Exploring access cavity through non-carious cervical lesions: Impacts on instrumentation, obturation, and fracture resistance in mandibular incisors.

AIM: To compare the effects of Cervical Access Cavity (CervAC) and Traditional Access Cavity (TradAC) on root canal preparation, root canal filling, and fracture resistance in mandibular incisors. METHODOLOGY: Twenty recently extracted and intact mandibular incisors were initially scanned using a micro-CT device. The specimens were anatomically matched to create two groups (n = 10). A wedge-shaped non-carious cervical lesion (NCCL) was created on the buccal aspect of all teeth using a double-faced segmented diamond disc. In group 1, a TradAC was prepared, whilst in group 2, access was created through the simulated NCCL using a round diamond bur 1012. After root canal preparation with Rotate instruments sizes 15/0.04, 20/0.04, and 25/0.04, the teeth were scanned again and evaluated for root canal volume and surface area, static voxels, volume of removed dental tissue, and dentine thickness. After that, the root canals were filled using the single-cone technique, teeth were restored with composite resin, and subsequently rescanned to calculate the volume of filling materials and voids. Then, the restored teeth were subjected to fracture resistance tests using a universal testing machine. Statistical comparisons between groups were performed with the Mann-Whitney test or the Student's t-test, with a statistical significance level of 5%. RESULTS: Statistical comparisons indicated no significant differences between groups in terms of root canal volume, surface area, static voxels, removed root dentine, root canal filling volume, percentage of voids, or fracture resistance load (p > .05). Conversely, teeth prepared with TradAC showed a significantly higher percentage of dental tissue removed from the crown (p = .001) and a greater volume of filling material remnants in the pulp chamber (p < .001) compared to the CervAC group. A significantly lower percentage reduction in dentine thickness was observed only on the mesial aspect of root at Level 1 in TradAC group (p = .008). CONCLUSIONS: CervAC can be considered a viable alternative approach in the presence of NCCL in mandibular incisors.

Chronic alcohol and nicotine consumption as catalyst for systemic inflammatory storm and bone destruction in apical periodontitis.

AIM: To assess the periapical alveolar bone pattern and the serum levels of proinflammatory cytokines, biochemical markers and metabolites in rats subjected to chronic alcohol and nicotine consumption and induced apical periodontitis. METHODOLOGY: Twenty-eight male Wistar rats were divided into four groups: Control, Alcohol, Nicotine and Alcohol+Nicotine. The alcohol groups were exposed to self-administration of a 25% alcohol solution, while the other groups were given only filtered water. The nicotine groups received daily intraperitoneal injections of a nicotine solution (0.19 µL of nicotine/mL), whereas the other groups received saline solution. Periapical lesions were induced by exposing the pulps of the left mandibular first molars for 28 days. After euthanasia, the mandibles were removed and the percentage bone volume, bone mineral density, trabecular thickness, trabecular separation and trabecular number of the periapical bone were measured using micro-computed tomography images. Serum samples were collected for analysis of proinflammatory cytokines (IL-1ß, IL-4, IL-6 and TNF-α), biochemical and metabolomic analysis. Statistical analysis was performed with a significance level of 5%. Nonparametric data were analysed using the Kruskal-Wallis test followed by Dunn's test, while one-way anova followed by Tukey's test was performed for parametric data. RESULTS: The groups exposed to alcohol or nicotine consumption exhibited an altered bone pattern indicating lower bone density and higher levels of IL-1ß, IL-6 and TNF-α compared to the Control group (p < .05). Significant differences were observed among the groups in the levels of aspartate aminotransferase (AST), alanine aminotransferase (ALT), alkaline phosphatase, cholesterol, triglycerides, urea, creatinine, albumin, uric acid, bilirubin and calcium. Metabolomic analysis revealed significant differences in glycine, phosphocholine, lysine, lactate, valine, pyruvate and lipids (CH2 CH2 CO), n(CH2 ) and n(CH3 ). Most of these parameters were even more altered in the simultaneous consumption of both substances compared to single consumption. CONCLUSION: Alcohol and nicotine chronic consumption altered several metabolic markers, impaired liver and kidney function, increased the production of systemic proinflammatory mediators and harmed the periapical bone microarchitecture in the presence of apical periodontitis. The simultaneous consumption of alcohol and nicotine intensified these detrimental effects.

Apical periodontitis as an aggravating factor for the severity of rheumatoid arthritis: An animal study.

AIM: The present study investigated the influence of apical periodontitis (AP) on the severity of rheumatoid arthritis (RA) using a Wistar rat model. METHODOLOGY: Forty male Wistar rats were distributed across four groups (n = 10) based on the induction of RA and AP: Control, RA, AP, and RA + AP. RA was induced through two immunisations with type II collagen emulsified in incomplete Freund's adjuvant, followed by one immunisation with complete Freund's adjuvant. After 21 days of RA induction, AP was induced by exposing the pulp of four molars. Animals were euthanized after 28 days of pulp exposure. Through the experiment, visual and behavioural assessments tracked RA development and the knees and hind paw joints were measured. Micro-computed tomography scans of knees and hind paws, as well as mandibles and maxillae, were conducted to evaluate RA severity and the presence of AP, respectively. Serum samples were collected to analyse proinflammatory cytokines (IL-1ß, IL-2, IL-17, and TNF-α). Non-parametric data were analysed using the Kruskal-Wallis test followed by Student-Newman-Keuls test, while one-way anova followed by Tukey's test was performed for parametric data. A significance level of 5% was employed. RESULTS: All molars submitted to access cavity developed AP. All joints subjected to arthritis induction developed the disease, with AP + RA demonstrating a higher arthritis severity when compared to the RA group (p < .05). RA + AP group displayed a significantly larger hind paw and knee circumference compared to the RA group (p < .05). Micro-CT images of RA and RA + AP groups revealed joints with erosions and bone deformities, with a significantly lower bone surface density, lower trabecular number and higher trabecular separation in the hind paw and a significantly lower percent bone volume and higher trabecular separation in the knees of RA + AP group compared to RA group (p < .05). RA + AP group exhibited a significantly higher level of TNF-α and a lower level of IL-2 compared to all other groups (p < .05). Both RA and RA + AP groups had significantly higher IL-17 levels (p < .05), while there was no significant difference in IL-1ß levels among the groups (p > .05). CONCLUSION: The findings from this study underscore a possible relationship between apical periodontitis and the exacerbation of rheumatoid arthritis.

Multimethod analysis of large- and low-tapered single file reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow.

AIM: To compare eight large- and low-tapered heat-treated reciprocating instruments regarding their design, metallurgy, mechanical properties, and irrigation flow through an in silico model. METHODOLOGY: A total of 472 new 25-mm E-Flex Rex (25/.04 and 25/.06), Excalibur (25/.05), Procodile (25/.06), Reciproc Blue R25 (25/.08v), WaveOne Gold Primary (25/.07v), and Univy Sense (25/.04 and 25/.06) instruments were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy (energy-dispersive X-ray spectroscopy and differential scanning calorimetry), and mechanical performance (cyclic fatigue, torsional resistance, cutting ability, bending and buckling resistance). Computational fluid dynamics assessment was also conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparations. Kruskal-Wallis and one-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments presented variations in blade numbers, helical angles, and tip designs, with all featuring non-active tips, symmetrical blades, and equiatomic nickel-titanium ratios. Cross-sectional designs exhibited an S-shaped geometry, except for WaveOne Gold. Univy 25/.04 and Reciproc Blue displayed the smallest and largest core diameters at D3. Univy 25/.04 and E-Flex Rec 25/.04 demonstrated the longest time to fracture (p < .05). Reciproc Blue and Univy 25/.04 exhibited the highest and lowest torque to fracture, respectively (p < .05). Univy 25/.04 and Reciproc Blue had the highest rotation angles, whilst E-Flex Rec 25/.06 showed the lowest angle (p < .05). The better cutting ability was observed with E-Flex Rec 25/.06, Procodile, Excalibur, and Reciproc Blue (p > .05). Reciproc R25 and E-Flex Rec showed the highest buckling resistance values (p < .05), with WaveOne Gold being the least flexible instrument. The impact of instruments' size and taper on wall shear stress and apical pressure did not follow a distinct pattern, although Univy 25/.04 and E-Flex Rec 25/.06 yielded the highest and lowest values for both parameters, respectively. CONCLUSIONS: Low-tapered reciprocating instruments exhibit increased flexibility, higher time to fracture, and greater angles of rotation, coupled with reduced maximum bending loads and buckling strength compared to large-tapered instruments. Nevertheless, low-tapered systems also exhibit lower maximum torque to fracture and inferior cutting ability, contributing to a narrower apical canal enlargement that may compromise the penetration of irrigants in that region.

Do the apical limit and diameter of the instrumentation influence the extrusion of sodium hypochlorite solution? A micro-CT study.

This study evaluated the influence of the apical limit and the diameter of the instrumentation on the extrusion of the irrigating solution. Sixty human lower premolars were distributed into 5 groups according to the apical limit and diameter of the root canal instrumentation (n = 12): (G-140) R40 instrument 1 mm above the tooth length (TL) (Control); (G-150) R50 instrument 1 mm above the TL; (GF25) R25 instrument at the TL; (GF40) R40 instrument at the root canal length and (GF50) R50 instrument at the TL. A space of 33.5 ± 1 mm3 was created for storage of the extruded solution. Omnipaque contrast was added to the NaOCl solution in a 1:2 ratio, totaling 15 mL of solution to allow its visualization when extruded in microcomputed tomography. Final irrigation was performed with a syringe and needle and activated with a passive ultrasonic irrigation (PUI). Three activation cycles were performed. Data were tabulated and statistically analyzed (one-way ANOVA) with a significance level set at 5%. It was observed irrigating solution extrusion after final irrigation in all groups. However, there were no statistically significant differences among experimental groups, regardless of the diameter or apical limit of root canal instrumentation (p > 0.05). The different apical limits and diameters of root canal instrumentation did not influence the volume of extruded irrigating solution using passive ultrasonic irrigation.

Comparative analysis of reciprocating and flat-side heat-treated rotary single-file systems: Design, metallurgical characteristics, and mechanical performance.

AIM: To compare two flat-side single-file rotary instruments with three single-file reciprocating systems through a multimethod assessment. METHODOLOGY: A total of 290 new NiTi single-file rotary (AF F One Blue 25/0.06 and Platinum V.EU 25/0.06) and reciprocating (One Files Blue R25, Reciproc Blue R25, Reciproc R25) instruments were selected, carefully examined for any major deformations, and evaluated regarding their macroscopic and microscopic design, nickel and titanium elements ratio, phase transformation temperatures, and mechanical performance (time/rotation to fracture, maximum torque, angle of rotation, microhardness, maximum bending, and buckling strengths). One-way anova post hoc Tukey, T-test, and nonparametric Mood's median tests were used for statistical comparisons (α = 5%). RESULTS: Tested instruments had identical blade counts and near-identical helical angles of approximately 24° (rotary instruments) and 151° (reciprocating instruments). The flat-side analysis revealed a few inconsistencies, such as discontinuity segments, different orientations, and gaps in the homogeneity of the bluish colour. Microscopically, flat-side instruments exhibited blade discontinuity and an incomplete S-shaped cross-section. The surface finish was smoother for One Files Blue and more irregular for both rotary instruments. There were distinct phase transformation temperatures amongst all instruments. All heat-treated instruments were in R-phase arrangement, and Reciproc was in R-phase plus austenite at test temperature (20°C). Compared with the reciprocating instruments, both flat-side instruments exhibited lower results in the cyclic fatigue tests using two different clockwise kinematics, maximum torque, angle of rotation, and maximum buckling strength (p < .05). The rotary systems also exhibited low flexibility (p < .05). AF F One Blue had the lowest microhardness, whilst Reciproc had the highest value. CONCLUSION: This multimethod investigation revealed that the flat-side rotary instruments underperformed the reciprocating instruments regarding cyclic fatigue (with two different clockwise kinematics), maximum torque, angle of rotation, maximum buckling strength, and flexibility. Manufacturing inconsistencies were also observed in some of the flat-side instruments, including discontinuity segments, different orientations, and in the homogeneity of their bluish colour given by the heat treatment.

Success rate of permanent teeth pulpotomy using bioactive materials: A systematic review and meta-analysis of randomized clinical trials.

BACKGROUND: The results of vital pulp treatments in permanent teeth have been encouraging. Currently, pulpotomy treatment for permanent teeth primarily utilizes mineral trioxide aggregate (MTA) as the dressing material, followed by calcium hydroxide. While other calcium-silicate-based cements have been suggested for pulpotomy, there is a limited number of studies evaluating their long-term effectiveness. OBJECTIVES: The objective of this systematic review and meta-analysis was to evaluate the success rate of pulpotomies performed on permanent teeth, comparing the use of ProRoot MTA with that of calcium hydroxide and other bioceramic materials. METHODS: A comprehensive search was conducted in several electronic databases, including PubMed, Cochrane Library, Scopus, Web of Science, Embase and Science Direct until December 2022. The search was guided by PICOS criteria, including only randomized clinical trials (RCTs) that evaluated the success rate of pulpotomy treatments in permanent teeth using ProRoot MTA in comparison to calcium hydroxide and other bioceramic materials. The quality of the included studies was assessed using the RoB-2 tool to evaluate the risk of bias, and relevant data were extracted and analysed in RevMan software 5.3 using fixed-effect models. The GRADE tool was used to determine the overall quality of evidence. RESULTS: The initial search retrieved 1072 studies and, after eliminating duplicates, 677 studies were screened and 28 studies were considered for eligibility. In the final selection process, 16 studies were included in the systematic review, with 10 being determined as having a high risk of bias. Pulpotomy showed an overall mean success rate of 92% after 1 year. The meta-analysis indicated a significantly higher success rate for pulpotomies utilizing MTA in comparison with calcium hydroxide, while no significant difference was seen between MTA and calcium-enriched mixture (CEM) or Biodentine. The GRADE assessment revealed an overall low level of evidence for the included studies. DISCUSSION: Most randomized controlled trials exhibited a significant absence of control over confounding factors. CONCLUSIONS: This systematic review and meta-analysis demonstrate that pulpotomy is a highly effective treatment for managing permanent teeth. The results indicate that the success rate of pulpotomy using ProRoot MTA is significantly higher than when using calcium hydroxide. However, the certainty of evidence supporting these findings is low, and there is a need for well-designed RCTs to assess the long-term outcomes of pulpotomy using newer bioceramic materials. REGISTRATION: This systematic review was registered in the PROSPERO database (registration number CRD42023393970).

Characterization of the file-specific heat-treated ProTaper Ultimate rotary system.

AIM: To compare design, metallurgy and mechanical performance of the ProTaper (PT) Ultimate system with instruments of similar dimensions from the ProGlider, PT Gold and PT Universal systems. METHODOLOGY: New PT Ultimate instruments (n = 248) were compared with instruments of similar dimensions from ProGlider (n = 31), PT Gold (n = 155) and PT Universal (n = 155) systems regarding their number of spirals, helical angle, blade symmetry, tip geometry, surface finishing, nickel/titanium ratio, phase transformation temperatures and mechanical performance. One-way anova and nonparametric Mood's median tests were used for statistical comparison (α = 5%). RESULTS: All instruments had symmetrical blades without radial lands or flat sides, similar surface finishing and an almost equiatomic nickel/titanium ratio, whilst the number of spirals, helical angles and the tip geometry were different. PT Ultimate instruments showed 3 distinct heat treatments that matched with the colour of their metal wire. Slider and ProGlider instruments had similar R-phase start (Rs) and R-phase finish (Rf) temperatures. SX, F1, F2, F3 and Shaper instruments showed equivalent heat treatments (Rs ~45.6°C and Rf ~28.3°C) that were similar to their PT Gold counterparts (Rs ~47.9°C and Rf ~28.2°C), but completely distinct to the PT Universal ones (Rs ~16.2°C and Rf ~-18.2°C). Amongst the PT Ultimate instruments, the lowest maximum torques were observed in the SX (0.44 N cm), Slider (0.45 N cm) and Shaper (0.60 N cm) instruments, whilst the highest was noted in the FXL (4.90 N cm). PT Ultimate Slider and ProGlider had similar torsional (~0.40 N cm) and bending loads (~145.0 gf) (p = 1.000), whilst the other PT Ultimate instruments showed statistically significantly lower maximum torque, higher angle of rotation and lower bending load (higher flexibility) than their counterparts of the PT Universal and PT Gold systems. CONCLUSIONS: The PT Ultimate system comprises instruments with 3 distinct heat treatments that showed similar phase transformation temperatures to their heat-treated analogues. PT Ultimate instruments presented lower torsional strength and superior flexibility than their counterparts, whilst maximum torque, angle of rotation and bending loads progressively increased with their sizes.

Multimethod analysis of three rotary instruments produced by electric discharge machining technology.

AIM: This study aimed to compare three rotary instruments produced by the EDM process with the heat-treated ProTaper Gold system regarding design, metallurgy, mechanical properties and shaping ability. METHODOLOGY: HyFlex EDM (25/~), Neoniti (25/.06), EDMax (25/.06) and ProTaper Gold (25/.08v) instruments (n = 58 per group) were compared regarding design, metallurgy and mechanical performance. Unprepared canal areas were calculated for each system after preparation of mesiobuccal, mesiolingual and distal canals of mandibular molars (15 canals per group) using micro-CT technology. Statistical analyses were performed using One-way anova post-hoc Tukey and Kruskal-Wallis post-hoc Dunn's tests (α = 5%). RESULTS: All instruments had asymmetrical blades, no radial lands, no major defects and almost equiatomic nickel/titanium ratios, but different cross-section designs, tip geometries and surface appearances. Although instruments had distinct transformation temperature curves, they showed crystallographic martensitic arrangement at 21°C and mixed austenite plus R-phase at body temperature. Neoniti and HyFlex EDM showed similar results in all mechanical tests (p > .05), while EDMax and ProTaper Gold had similar time to fracture (p = .841), maximum bending load (p = .729), and cutting ability (p = .985). ProTaper Gold showed the highest torque to failure (p < .001) and HyFlex EDM had the lowest buckling resistance (p < .001). Mean percentages of unprepared canal areas ranged from 20.4% to 25.7% in the mesial canals, and from 20.8% to 26.2% in the distal canal, with no statistical differences among systems (p > .05). CONCLUSIONS: Instruments' geometry and phase transformation temperatures influenced the results of the mechanical tests, but not their shaping ability.

To flat or not to flat? Exploring the impact of flat-side design on rotary instruments using a comprehensive multimethod investigation.

AIM: To assess the influence of a flat-side design on the geometry, metallurgy, mechanical performance and shaping ability of a novel nickel-titanium rotary instrument. METHODOLOGY: Sixty-five new 25-mm flat-side rotary instruments (size 25, taper 0.04) and their nonflat-side prototypes (n = 65) were assessed for major deformations and examined regarding macroscopic and microscopic design, determination of nickel and titanium elements ratio, measurement of phase transformation temperature and evaluation of mechanical performance parameters including time/cycles to fracture, maximum torque, angle of rotation, maximum bending and buckling strengths and cutting ability. Additionally, unprepared canal areas, volume of hard tissue debris and percentage reduction of dentine thickness were calculated for each tested instrument after preparing mesial canals of mandibular molars (n = 12), using micro-CT imaging. Statistical analyses were performed using the U-Mann-Whitney test and independent Student t-test (α = 5%). RESULTS: The number of spirals (n = 8) and blade direction (clockwise) were similar between both flat and nonflat instruments, whilst the helical angles were equivalent (⁓25°). Flat-instruments showed inconsistencies in the homogeneity of the gold colour on the flat-side surface, blade discontinuity, and incomplete and variable S-shaped cross-sections. The titanium-to-nickel ratios were equivalent, but significant differences in the R-phase finish and austenitic start phase transformation temperatures were observed between the flat and nonflat-side instruments. The flat-side instruments demonstrated superior cutting ability compared to the nonflat instruments, as well as, significantly lower values for time to fracture, rotation to fracture and maximum torque to fracture (p < .001). No statistical difference was observed between tested instruments regarding angle of rotation (p = .437), maximum bending (p = .152) and buckling load (p = .411). Preparation protocols using flat and nonflat instruments did not show any statistically significant differences (p > .05). All flat-side instruments exhibited deformation after shaping procedures. CONCLUSIONS: The flat-side instrument showcased enhanced cutting ability compared to its nonflat counterpart. However, it exhibited inferior performance in terms of time, rotation and maximum torque to fracture, along with distinct phase transformation temperatures. No differences were observed in the titanium-to-nickel ratios, angle of rotation, maximum bending, buckling load, preparation time, percentage of untouched canal walls, volume of hard tissue debris and percentage reduction of dentine thickness.

Characterization of four heat-treated reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow patterns.

AIM: To compare the design, metallurgy, and mechanical properties of four heat-treated reciprocating instruments coupled with the evaluation of the irrigation flow using an in silico model. METHODOLOGY: New EdgeOne Fire Primary, Easy-File Flex Regular 25, WaveOne Gold Primary and Reciproc Blue R25 instruments (n = 124) were initially evaluated regarding their design through stereomicroscopy, scanning electron microscopy and 3D surface scanning. In addition, energy-dispersive X-ray spectroscopy was utilized to determine their elemental composition, and differential scanning calorimetry tests to evaluate their phase transformation temperatures. Their mechanical performance was further assessed through torsional and bending tests. Using scans obtained from a real tooth and the instruments, a computational fluid dynamics assessment was conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparation. Mood's median and One-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Reciproc Blue exhibited a superior number of blades (n = 8), whereas EdgeOne Fire had the highest overall volume (4.38 mm3 ) and surface area (32.32 mm2 ). At the 3-mm axial level, EdgeOne Fire displayed the lowest core diameter (0.13 mm), while Reciproc Blue had the highest (0.16 mm). All blades were symmetrical, and the tips of the instruments were non-active but differed from each other. The most irregular surfaces were observed in EdgeOne Fire and Easy-File Flex. All instruments were manufactured from nickel-titanium alloys and exhibited distinct phase transformation temperatures. WaveOne Gold and Reciproc Blue demonstrated the highest maximum torque values (1.87 and 1.62 N cm, respectively), while the lowest was observed on EdgeOne Fire (1.21 N cm) (p < .05). The most flexible (p < .05) were EdgeOne Fire (angle of rotation: 602.6°; maximum bending load: 251.4 g.f) and Reciproc Blue (533.2° and 235.6 g.f). There were no significant differences observed in the irrigation flow among the four domains generated by the tested instruments. CONCLUSIONS: Despite observing variations in the design, phase transformation temperatures, and in the torsional and bending test outcomes among the four heat-treated reciprocating instruments, no significant differences were found in the irrigation flow pattern among the different groups in the simulated root canal preparations.

Volumetric changes in root canal sealers in ex vivo and a novel animal model approach.

AIM: This study aimed to evaluate the volumetric change of root canal sealers through micro-computed tomographic analysis using a novel in vivo model and to compare the results with those obtained using an ex vivo test. METHODOLOGY: Eighteen single-rooted teeth were cut to 5 mm length from the root apex. The root canals were uniformly enlarged and filled with EndoSequence BC Sealer or AH Plus Jet root canal sealers. Samples were stored at 37°C and 95% relative humidity for 24 h and then scanned with a micro-CT device. Twelve samples (n = 6 for each sealer) were implanted in the subcutaneous tissue of Wistar rats, while six samples (n = 3 for each sealer) were immersed in 20 mL of phosphate-buffered saline (PBS) at 37°C at neutral pH. After 7 and 30 days, teeth were removed from subcutaneous tissue or PBS and rescanned. Statistical analysis of volume changes was performed using Shapiro-Wilk's test and independent t-test (p < .05). RESULTS: AH Plus Jet had smaller volume changes (-2.2 to +0.77%) than EndoSequence BC Sealer (-2.0 to +4.0%) (p < .05), in the two tested models. The volume of the root canal sealers decreased over time (p < .05), in vivo. AH Plus Jet results varied between the in vivo and ex vivo results (p < .05), while EndoSequence BC Sealer presented similar volume losses for both experimental models (p > .05). CONCLUSION: EndoSequence BC Sealer lost more volume than AH Plus Jet. The experimental conditions influenced the volumetric change of AH Plus Jet but not the EndoSequence BC Sealer. The ex vivo model should be further explored as a methodological alternative to assess the volumetric changes of root canal sealers without causing harm to animals.

Design, metallurgy, mechanical properties, and shaping ability of 3 heat-treated reciprocating systems: a multimethod investigation.

OBJECTIVE: This study aimed to compare 3 reciprocating systems regarding design, metallurgy, mechanical properties, and shaping ability. MATERIALS AND METHODS: New Reciproc Blue R25, WaveOne Gold Primary, and REX 25 instruments (n=41 per group) were analyzed regarding design, metallurgy, and mechanical performance, while shaping ability (untouched canal walls, volume of removed dentin, and hard tissue debris) was tested in 36 anatomically matched root canals of mandibular molars. Results were compared using one-way ANOVA post hoc Tukey and Kruskal-Wallis tests with a significant level set at 5%. RESULTS: All instruments showed symmetrical cross sections with asymmetrical blades, no radial lands, no major defects, and an almost equiatomic nickel and titanium ratio. The highest R-phase start temperatures were observed with WaveOne Gold (46.1°C) and REX (44.8°C), while Reciproc Blue had the lowest R-phase start (34.5°C) and finish (20°C) temperatures. WaveOne Gold had the lowest time to fracture (169 s) and the highest maximum load (301.6 gf) (P <0.05). The maximum torque of Reciproc Blue (2.2 N.cm) and WaveOne Gold (2.1 N.cm) were similar (P >0.05), but lower than REX (2.6 N.cm) (P <0.05). No statistical differences were observed among instruments in the angle of rotation (P >0.05) and in the shaping ability in both mesial and distal canals (P >0.05). CONCLUSION: Although the overall design, temperature transition phases and mechanical behavior parameters were different among tested instruments, they were similar in terms of shaping ability. CLINICAL RELEVANCE: All tested heat-treated NiTi reciprocating systems showed similar shaping ability, without clinically significant errors.

Shaping ability of novel nickel-titanium systems in printed primary molars.

BACKGROUND: Manual or mechanized instruments can be used for root canal preparation. Manual instrumentation using K-files is widely used in primary teeth, but there are many limitations. Mechanized root canal preparation can lead to easy access to all canals, decrease instrumentation time, and result in more funnel-shaped root canals, resulting in a more predictable uniform paste fill. AIM: This study aimed to evaluate the shaping ability and instrumentation time of VDW.ROTATE™ and EdgeTaper Platinum™ during the preparation of resin-printed primary molars. Hand K-files were used as a reference for comparison. DESIGN: Sixty-six resin-based maxillary second primary molars, obtained from extracted tooth cone-beam computed tomography (CBCT) image and printed on a three-dimensional printer, were divided into three groups: VDW.ROTATE™, EdgeTaper Platinum™, and K-files. The specimens were scanned using CBCT imaging before and after root canal preparation. Images were registered using a dedicated software, and changes (Δ) in the canal area, volume, and untouched canal surface were calculated. Instrumentation time was evaluated. Data were statistically analyzed using the SPSS program. RESULTS: There was no significant difference among the tested file systems for Δ canal volume and area (p > .05). VDW.ROTATE™, however, showed significantly lower untouched canal surface area than other systems in all roots (p < .001). The VDW.ROTATE™ was found to be significantly faster (6.47 ± 0.39 min) than EdgeTaper Platinum™ (7.71 ± 0.73 min) and K-files (8.22 ± 0.72 min), (p < .05). CONCLUSIONS: The shaping ability and the instrumentation time were directly influenced by the root canal instrumentation system used during the preparation of resin-printed primary molars, with VDW.ROTATE™ being the faster system and associated with the lower amount of untouched canal surface area.

Mechanical activation with Easy Clean device enhanced organic tissue removal from simulated internal root resorption in a laboratory evaluation.

BACKGROUND: Considering the irregular shape of the root canal, removing inflamed pulp and granulation tissue completely from internal resorption cavities during chemomechanical preparation can be challenging. This study aimed to evaluate the effectiveness of passive ultrasonic irrigation (PUI) compared to mechanical activation with Easy Clean in the removal of organic tissue from simulated areas of internal root resorption. METHODS: The root canals of 72 extracted single-rooted teeth with oval canals were instrumented with Reciproc R25 instruments. After root canal preparations, the specimens were split longitudinally, and semicircular cavities were prepared using a round bur on each half of the roots. Samples obtained from bovine muscle tissue were weighed and adapted into semicircular cavities. The roots were reassembled and joined, and the teeth were divided into six groups (n = 12) according to the irrigation protocol: Sodium hypochlorite (NaOCl) without activation; NaOCl + PUI; NaOCl + Easy Clean; distilled water without activation; distilled water + PUI; and distilled water + Easy Clean. After irrigation protocols, the teeth were disassembled, and the remaining organic tissue was weighed. Data were analyzed by two-way ANOVA and Tukey's post hoc test (p < 0.05). RESULTS: None of the experimental protocols totally removed the bovine tissue from simulated cavities. Tissue weight reduction was significantly affected by the activation method (p < 0.05) and by irrigation solution (p < 0.05). Groups with NaOCl irrigation presented higher tissue weight loss when compared to distilled water, for all irrigation methods (p < 0.05). The use of Easy Clean resulted in the greatest tissue weight loss (42.0%-Distilled water/45.5%- NaOCl) compared to those of PUI (33.3%-Distilled water/37.7%- NaOCl) and no activation (33.4%-Distilled water/38.8%- NaOCl) (p < 0.05). However, no differences were observed between PUI and no activation groups (p > 0.05). CONCLUSIONS: Mechanical activation with Easy Clean enhanced organic tissue removal from simulated internal resorption more effectively than PUI. Easy Clean for agitation of the irrigating solution is effective in removing simulated organic tissues from artificial internal resorption cavities, being an alternative to the use of PUI.

Present status and future directions - Minimal endodontic access cavities.

In the last decades, the move of medicine towards minimally invasive treatments is notorious and scientifically grounded. As dentistry naturally follows in its footsteps, minimal access preparation have also becume a trend topic in the endodontic field. This procedure aims to maximize preservation of dentine tissue backed up by the idea that this is an effective way to reduce the incidence of post-treatment tooth fracture. However, with the assessment of the body of evidence on this topic, it is possible to observe some key points (a) the demand for nomenclature standardization, (b) the requirement of specific tools such as ultra-flexible instruments, visual magnification, superior illumination, and three-dimensional imaging technology, (c) minimally invasive treatment does not seem to affect orifice location and mechanical preparation when using adequate armamentarium, but it (d) may impair adequate canal cleaning, disinfection and filling procedures, and also (e) it displays contradictory results regarding the ability to increase the tooth strengthen compared to the traditional access cavity. In spite of that, it is undeniable that methodological flaws of some benchtop studies using extracted teeth may be responsible for the conflicting data, thus triggering the need for more sophisticated devices/facilities and specifically designed research in an attempt to make clear the role of the access size/design on long-term teeth survival. Moreover, it is inevitable that a clinical approach such as minimal endodontic access cavities that demands complex tools and skilled and experienced operators bring to the fore doubts on its educational impact mainly when confronted with the conflicting scientific output, ultimately provoking a cost-benefit analysis of its implementation as a routine technique. In addition, this review discusses the ongoing scientific and clinical status of minimally invasive access cavities aiming to input an in-depth and unbiased view over the rationale behind them, uncovering not only the related conceptual and scientific flaws but also outlining future directions for research and clinical practices. The conclusions attempt to skip from passionate disputes highlighting the current body of evidence as weak and incomplete to guide decision making, demanding the development of a close-to-in situ laboratory model or a large and well-controlled clinical trial to solve this matter.

A critical analysis of research methods and experimental models to study dentinal microcracks.

The purpose of this narrative review was to discuss the scientific milestones that led to the current understanding of the root dentinal microcrack phenomenon based on the interplay between the usage of micro-computed tomography (micro-CT) as an analytical tool alongside a close-to-mouth experimental model. In 2009, reports on the development of dentinal microcracks in extracted teeth after root canal preparation triggered an awareness of the potential for vertical root fractures (VRFs) of endodontically treated teeth could be developed from defects created by the mechanical stress of nickel-titanium preparation systems on dentine. This assumption was taken for granted, even though no cause-effect relationship had been scientifically demonstrated. Since then, several studies using the sectioning method with extracted teeth have been published and the large discrepancy amongst their outcomes soon become evident. Moreover, the high frequency of reported dentinal microcracks largely contrasted with the clinical incidence of VRFs, raising doubts on their methodological reliability. Using micro-CT technology, it was demonstrated by several studies that, in extracted teeth, dentinal defects already existed before the endodontic procedures, indicating that the initial reports framed a non-existing cause-effect relationship between canal preparation and dentinal microcracks. Although these new findings contributed to a better comprehension of this phenomenon, the misconception that microcracks were the starting point for VRFs was only surpassed with a new in situ approach using fresh cadavers. Surprisingly, microcracks were not identified in sound teeth. As a conclusion, dentinal microcracks in extracted teeth can be considered a non-natural occurrence observed only in a laboratory set-up as a consequence of dehydration and storage conditions. Thus, dentinal microcracks shall not be considered as the starting point for VRFs as they do not manifest in non-extracted teeth. Identifying dentinal microcracks as a laboratory phenomenon highlights the impact of recent scientific developments to disclaim the clinical relevance of laboratory-obtained outcomes.

Influence of access cavity preparation on the dentine thickness of mesial canals of mandibular molars prepared with reciprocating instruments.

AIM: To evaluate the influence of traditional and conservative access cavity preparations on the remaining dentine thickness in the coronal third of mesial canals of extracted mandibular molars prepared with reciprocating instruments using micro-computed tomography as the analytical tool. METHODOLOGY: Seventy extracted mandibular molars were scanned at a pixel size of 19 µm. From this initial sample, 20 teeth were selected, pair-matched and distributed into two groups (n = 10) according to the access cavity preparation: traditional (TradAC) or conservative (ConsAC). The root canals were sequentially enlarged with Reciproc Blue R25 (size 25, 0.08v taper) and R40 (size 40, 0.06v taper) instruments. A new scan was performed and the postoperative stacks were coregistered with their respective preoperative datasets. A colour-coded cross sections of the roots were created and used to identify and measure the smallest dentine thickness related to both MB and ML canals at 1.0-mm intervals from the furcation level of up to 5 mm in the apical direction, in both mesial and distal aspects of the roots, before and after preparation. The statistical analyses were performed with paired-samples t-test, independent-samples Student T-test and Chi-Square test with a significance level of 5%. RESULTS: At all levels of both groups, dentine thickness before preparation was greater than after preparation (p < .05). No difference in the percentage of dentine reduction was observed between TradAC and ConsAC groups (p > .05), but a significantly greater reduction was observed to the distal aspect of the roots (p < .05). After root canal preparation, dentine thinner than 0.5 mm was observed mostly along the distal aspect of the root (10% to 15%) of the MB and ML canals, with no influence of the access cavity type on its incidence to either mesial (X2  = 1.66; p = .2) or distal (X2  = 0.40; p = .5) directions. In the TradAC group, dentine thickness in most slices was greater than 1.0 mm after preparation (n = 124) whilst, in the ConsAC, it ranged from 0.5 to 1.0 mm (n = 136). CONCLUSION: Traditional or conservative access cavity preparation in extracted mandibular molars did not influence the remaining dentine thickness in the coronal third of mesial canals enlarged with thermomechanically treated nickel-titanium reciprocating instruments.

A critical analysis of research methods and experimental models to study root canal fillings.

Canal filling materials and techniques have been one of the most studied topics in Endodontics. A simple search using the mesh term "root canal filling" in PubMed revealed more than 11 000 articles, an impressive number that is much higher than "root canal disinfection" (5544 articles) or even the popular "root canal preparation" (8527 articles). The overriding importance attributed to root filling procedures is not merely intuitive. It derived from the appealing relevance given by the appearance of the white lines in common radiographs grounded on retrospective clinical data that had identified the quality of a root filling as one of the major causes of treatment failure (lack of healing). Since the publication of the Washington study, impressive efforts have been made for the release of new materials and techniques, as well as, for the development of a plethora of laboratory methods to assess the quality of root filling procedures. This narrative review aims to address and discuss the most relevant laboratory methods to assess the root canal filling. As filling quality improvements have not translated into higher success rates, as reported in longitudinal clinical studies, more than to deliver a simple methodology-based review, this paper aims to present an in-depth critical view on the assessment of laboratory methods used to study the filling materials and techniques. Recent data indicate that the long-term dimensional stability/degradation over time of endodontic sealers plays a central role in the treatment outcome. In this context, laboratory methods should be developed focusing on predicting, at least to some degree, the long-term clinical behaviour of root canal fillings, rather than simply ranking different materials or techniques.

Micro-CT assessment of gap-containing areas along the gutta-percha-sealer interface in oval-shaped canals.

AIM: To assess the interfacial adaptation (gap-containing areas) of two root canal sealers (EndoSequence BC Sealer and AH Plus) to a conventional gutta-percha (GP) cone (GP-sealer interface) in oval-shaped canals filled using the single cone technique. METHODOLOGY: Sixteen teeth with oval-shaped canals were selected, scanned in a micro-computed tomographic device, and pair-matched according to the volume, aspect ratio and configuration of root canals. Root canals were then sequentially prepared with WaveOne Gold Primary and Large instruments, followed by filling with WaveOne Large GP points associated with either the premixed calcium-silicate EndoSequence BC Sealer or the epoxy resin-based AH Plus sealer (n = 8 per group) using the single cone technique. After 7 days stored in phosphate-buffered saline solution at 37°C, the specimens were rescanned and the reconstructed images segmented in order to differentiate the filling materials (sealer and GP cone) to the dentine. A total of 453 cross-sectional slices were assessed and categorized according to the presence or absence of gaps at the GP-sealer interface. Mann-Whitney U-test verified the differences between groups and were considered significant at alpha = 5%. RESULTS: Gaps were non-homogenously distributed in two-dimensional axial cross-section images and none of the specimens showed completely gap-free areas along the entire GP-sealer interface. Root canals filled with EndoSequence BC Sealer and AH Plus displayed 171 (37.75%) and 136 (30.02%) slices with gaps in the GP-sealer interface and these frequencies were statistically significant (p = .000). CONCLUSIONS: Although none of the specimens had a gap-free area along the entire GP-sealer interface, oval canals filled with AH Plus showed less gaps than the ones filled with EndoSequence BC Sealer.