Antimicrobial surface processing of polymethyl methacrylate denture base resin using a novel silica-based coating technology.

OBJECTIVES: This study investigated the surface characteristics of denture base resin coatings prepared using a novel silica-based film containing hinokitiol and assessed the effect of this coating on Candida albicans adhesion and growth. METHODS: Silica-based coating solutions (control solution; CS) and CS containing hinokitiol (CS-H) were prepared. C. albicans biofilm formed on denture base specimens coated with each solution and these uncoated specimens (control) were analyzed using colony-forming unit (CFU) assay, fluorescence microscopy, and scanning electron microscopy (SEM). Specimen surfaces were analyzed by measuring the surface roughness and wettability and with Fourier-transform infrared (FT-IR) and proton nuclear magnetic resonance (1H NMR). Stability of coated specimens was assessed via immersion in water for 1 week for each group (control-1w, CS-1w, and CS-H-1w) followed by CFU assay, measurement of surface roughness and wettability, and FT-IR. RESULTS: CS-H and CS-H-1w contained significantly lower CFUs than those present in the control and control-1w, which was also confirmed via SEM. Fluorescence microscopy from the CS-H group identified several dead cells. The values of surface roughness from coating groups were significantly less than those from the control and control-1w. The surface wettability from all coating groups exhibited high hydrophobicity. FT-IR analyses demonstrated that specimens were successfully coated, and 1H NMR analyses showed that hinokitiol was incorporated inside CS-H. CONCLUSIONS: A silica-based denture coating that incorporates hinokitiol inhibits C. albicans growth on denture. CLINICAL RELEVANCE: We provide a novel antifungal denture coating which can be helpful for the treatment of denture stomatitis.

Microbicidal effect of 405-nm blue LED light on Candida albicans and Streptococcus mutans dual-species biofilms on denture base resin.

This study investigated: (1) the microbicidal effect of 405-nm blue LED light irradiation on biofilm formed by Candida albicans hyphae and Streptococcus mutans under dual-species condition on denture base resin, (2) the generation of intracellular reactive oxygen species (ROS) induced by irradiation, and (3) the existence of intracellular porphyrins, which act as a photosensitizer. Denture base resin specimens were prepared and C. albicans and S. mutans dual-species biofilms were allowed to form on the specimens. The biofilms were irradiated with 405-nm blue LED light and analyzed using the colony-forming unit assay, fluorescence microscopy, and scanning electron microscopy (SEM). Single-species biofilms of C. albicans and S. mutans formed on the specimens were irradiated with 405-nm blue LED light. After the irradiation, the intracellular ROS levels in C. albicans and S. mutans cells were measured. In addition, the level of intracellular porphyrins in C. albicans and S. mutans were measured. Irradiation for more than 30 min significantly inhibited the colony formation ability of C. albicans and S. mutans. Fluorescence microscopy revealed that almost all C. albicans and S. mutans cells were killed by irradiation. SEM images showed various cell damage patterns. Irradiation led to the generation of intracellular ROS and porphyrins were present in both C. albicans and S. mutans cells. In conclusion, irradiation with 405-nm blue light-emitting diode light for 40 min effectively disinfect C. albicans hyphae and S. mutans dual-species biofilms and possibly react with intracellular porphyrins resulting in generation of ROS in each microorganism.

Inhibitory effect of 405-nm blue LED light on the growth of Candida albicans and Streptococcus mutans dual-species biofilms on denture base resin.

We investigated whether irradiation with 405-nm blue LED light could inhibit the growth of not only single- but dual-species biofilms formed by Candida albicans and Streptococcus mutans on denture base resin and cause the alteration in gene expression related to adhesion and biofilm formation. C. albicans and S. mutans single-/dual-species biofilms were formed on the denture base specimens. The biofilms were irradiated with 405-nm blue LED light (power density output: 280 mW/cm2) for 0 (control) and 40 min. Dual-species biofilms were analyzed using CFU assay and fluorescence microscopy, and single-/dual-species biofilms were analyzed using alamarBlue assays and gene expression analysis. To assess the inhibitory effect of irradiation on dual-species biofilms, specimens after irradiation were aerobically incubated for 12 h. After incubation, the inhibition of growth was assessed using CFU assays and fluorescence microscopy. Data were analyzed using the Mann-Whitney U or Student's t test (p < 0.05). Irradiation produced a significant inhibitory effect on biofilms. Fluorescence microscopy revealed that almost all C. albicans and S. mutans cells were killed by irradiation, and there was no notable difference in biofilm thickness immediately after irradiation and after irradiation and incubation for 12 h. alamarBlue assays indicated the growth of the biofilms was inhibited for 12-13 h. The expression of genes associated with adhesion and biofilm formation-als1 in C. albicans and ftf, gtfC, and gtfB in S. mutans-significantly reduced by irradiation. Irradiation with 405-nm blue LED light effectively inhibited the growth of C. albicans and S. mutans dual-species biofilms for 12 h.

Effectiveness of 405-nm blue LED light for degradation of Candida biofilms formed on PMMA denture base resin.

This study investigated (i) the degradation effect of 405-nm blue light-emitting diode (LED) light irradiation on Candida albicans and C. glabrata biofilms formed on denture base resin and (ii) the effects of 405-nm blue LED light irradiation on the mechanical and surface characteristics of the resin. Polymethyl methacrylate denture base resin discs were prepared, and C. albicans or C. glabrata biofilms formed on the denture base resin discs. Each biofilm was irradiated with 405-nm blue LED light under a constant output power (280 mW/cm2) for different times in a moisture chamber with 100% relative humidity. Postirradiation, each biofilm was analyzed using a colony-forming unit assay, fluorescence microscopy, and scanning electron microscopy (SEM). Parallelepiped specimens of acrylic resin were prepared, and changes in their flexural strength (FS), flexural modulus (FM), and surface roughness (Ra) preirradiation and postirradiation with 405-nm blue LED light were evaluated. Irradiation for 30 min completely inhibited colony formation in both Candida species. Fluorescence microscopy showed that almost all Candida cells were killed because of irradiation. SEM images showed various cell damage patterns, such as wrinkles, shrinkage, and cell surface damage. An increase in FS was noted postirradiation, but no significant changes were observed in FM and Ra preirradiation and postirradiation. In conclusion, irradiation with 405-nm blue LED light induces degradation of C. albicans and C. glabrata biofilms on denture base resin, even in the absence of photosensitizers, without resin surface deterioration.

Ozone ultrafine bubble water inhibits the early formation of Candida albicans biofilms.

This study aimed to investigate the effect of ozone ultrafine bubble water (OUFBW) on the formation and growth of Candida albicans (C. albicans) biofilms and surface properties of denture base resins. OUFBWs were prepared under concentrations of 6 (OUFBW6), 9 (OUFBW9), and 11 ppm (OUFBW11). Phosphate buffered saline and ozone-free electrolyte aqueous solutions (OFEAS) were used as controls. Acrylic resin discs were made according to manufacturer instructions, and C. albicans was initially cultured on the discs for 1.5 h. A colony forming unit (CFU) assay was performed by soaking the discs in OUFBW for 5 min after forming a 24-h C. albicans biofilm. The discs after initial attachment for 1.5 h were immersed in OUFBW and then cultured for 0, 3, and 5 h. CFUs were subsequently evaluated at each time point. Moreover, a viability assay, scanning electron microscopy (SEM), Alamar Blue assay, and quantitative real-time polymerase chain reaction (qRT-PCR) test were performed. To investigate the long-term effects of OUFBW on acrylic resin surface properties, Vickers hardness (VH) and surface roughness (Ra) were measured. We found that OUFBW9 and OUFBW11 significantly degraded the formed 24-h biofilm. The time point CFU assay showed that C. albicans biofilm formation was significantly inhibited due to OUFBW11 exposure. Interestingly, fluorescence microscopy revealed that almost living cells were observed in all groups. In SEM images, the OUFBW group had lesser number of fungi and the amount of non-three-dimensional biofilm than the control group. In the Alamar Blue assay, OUFBW11 was found to suppress Candida metabolic function. The qRT-PCR test showed that OUFBW down-regulated ALS1 and ALS3 expression regarding cell-cell, cell-material adhesion, and biofilm formation. Additionally, VH and Ra were not significantly different between the two groups. Overall, our data suggest that OUFBW suppressed C. albicans growth and biofilm formation on polymethyl methacrylate without impairing surface properties.

Grapefruit seed extract effectively inhibits the Candida albicans biofilms development on polymethyl methacrylate denture-base resin.

This study aimed to investigate the cleansing effects of grapefruit seed extract (GSE) on biofilms of Candida albicans (C. albicans) formed on denture-base resin and the influence of GSE on the mechanical and surface characteristics of the resin. GSE solution diluted with distilled water to 0.1% (0.1% GSE) and 1% (1% GSE) and solutions with Polident® denture cleansing tablet dissolved in distilled water (Polident) or in 0.1% GSE solution (0.1% G+P) were prepared as cleansing solutions. Discs of acrylic resin were prepared, and the biofilm of C. albicans was formed on the discs. The discs with the biofilm were treated with each solution for 5 min at 25°C. After the treatment, the biofilm on the discs was analyzed using a colony forming unit (CFU) assay, fluorescence microscopy, and scanning electron microscopy (SEM). In order to assess the persistent cleansing effect, the discs treated with each solution for 5 min were aerobically incubated in Yeast Nitrogen Base medium for another 24 h. After incubation, the persistent effect was assessed by CFU assay. Some specimens of acrylic resin were immersed in each solution for 7 days, and changes in surface roughness (Ra), Vickers hardness (VH), flexural strength (FS), and flexural modulus (FM) were evaluated. As a result, the treatment with 1% GSE for 5 min almost completely eliminated the biofilm formed on the resin; whereas, the treatment with 0.1% GSE, Polident, and 0.1% G+P for 5 min showed a statistically significant inhibitory effect on biofilms. In addition, 0.1% GSE and 0.1% G+P exerted a persistent inhibitory effect on biofilms. Fluorescence microscopy indicated that Polident mainly induced the death of yeast, while the cleansing solutions containing at least 0.1% GSE induced the death of hyphae as well as yeast. SEM also revealed that Polident caused wrinkles, shrinkage, and some deep craters predominantly on the cell surfaces of yeast, while the solutions containing at least 0.1% GSE induced wrinkles, shrinkage, and some damage on cell surfaces of not only yeasts but also hyphae. No significant changes in Ra, VH, FS, or FM were observed after immersion in any of the solutions. Taken together, GSE solution is capable of cleansing C. albicans biofilms on denture-base resin and has a persistent inhibitory effect on biofilm development, without any deteriorations of resin surface.

Superhydrophilic co-polymer coatings on denture surfaces reduce Candida albicans adhesion-An in vitro study.

OBJECTIVE: In this study, we aimed to investigate denture-base-resin coatings prepared with a crosslinkable co-polymer containing sulfobetaine methacrylamide (SBMAm) and the relationship between their surface characteristics and the initial adhesion of Candida albicans (C. albicans). METHODS: Acrylic resin discs were coated with co-polymers containing various concentrations of SBMAm and N,N'-(4,7,10-trioxa-1,13-tridecadiamine) diacrylamide (JDA) as crosslinking agent. Uncoated discs were used as controls. An acquired pellicle was formed on each disc using artificial saliva, and the discs were immersed in a suspension of C. albicans (JCM2085) cells. After incubation, tetrazolium salt (XTT-reduction) and colony forming unit (CFU) assays were performed and the morphogenesis of C. albicans was examined using scanning electron microscopy (SEM). The surface roughness, film thickness, and the water contact angle of each disc surface were measured. RESULTS: All coating groups showed significantly lower amounts of adhered C. albicans in the XTT-reduction and CFU assays than the control, confirmed by the SEM images. Many wrinkle structures were observed on the surfaces coated with co-polymers containing more than 30% SBMAm. There were no significant differences in surface roughness among all groups. The co-polymer films on the coated discs were less than 5.0 µm in thickness, and these surfaces exhibited significantly lower mean water contact angles than the control. CONCLUSION: Crosslinkable co-polymers containing SBMAm can enhance the hydrophilicity of the surface of denture-base resins and reduce the initial adhesion of C. albicans.