In vivo and in vitro degradation comparison of pure Mg, Mg-10Gd and Mg-2Ag: a short term study.

The purpose of this study was to compare short term in vitro and in vivo biodegradation studies with low purity Mg (> 99.94 %), Mg-10Gd and Mg-2Ag designed for biodegradable implant applications. Three in vitro testing conditions were applied, using (i) phosphate buffered saline (PBS), (ii) Hank's balanced salt solution (HBSS) and (iii) Dulbecco's modified eagle medium (DMEM) in 5 % CO2 under sterile conditions. Gas evolution and mass loss (ML) were assessed, as well as the degradation layer, by elemental mapping and scanning electron microscopy (SEM). In vivo, implantations were performed on male Sprague-Dawley rats evaluating both, gas cavity volume and implant volume reduction by micro-computed tomography (µCT), 7 d after implantation. Samples were produced by casting, solution heat treatment and extrusion in disc and pin shape for the in vitro and in vivo experiments, respectively. Results showed that when the processing of the Mg sample varied, differences were found not only in the alloy impurity content and the grain size, but also in the corrosion behaviour. An increase of Fe and Ni or a large grain size seemed to play a major role in the degradation process, while the influence of alloying elements, such as Gd and Ag, played a secondary role. Results also indicated that cell culture conditions induced degradation rates and degradation layer elemental composition comparable to in vivo conditions. These in vitro and in vivo degradation layers consisted of Mg hydroxide, Mg-Ca carbonate and Ca phosphate.

Simulation as a set-up for technical proficiency: can a virtual warm-up improve live fibre-optic intubation?

BACKGROUND: Fibre-optic intubation (FOI) is an advanced technical skill, which anaesthesia residents must frequently perform under pressure. In surgical subspecialties, a virtual 'warm-up' has been used to prime a practitioner's skill set immediately before performance of challenging procedures. This study examined whether a virtual warm-up improved the performance of elective live patient FOI by anaesthesia residents. METHODS: Clinical anaesthesia yr 1 and 2 (CA1 and CA2) residents were recruited to perform elective asleep oral FOI. Residents either underwent a 5 min, guided warm-up (using a bronchoscopy simulator) immediately before live FOI on patients with predicted normal airways or performed live FOI on similar patients without the warm-up. Subjects were timed performing FOI (from scope passing teeth to viewing the carina) and were graded on a 45-point skill scale by attending anaesthetists. After a washout period, all subjects were resampled as members of the opposite cohort. Multivariate analysis was performed to control for variations in previous FOI experience of the residents. RESULTS: Thirty-three anaesthesia residents were recruited, of whom 22 were CA1 and 11 were CA2. Virtual warm-up conferred a 37% reduction in time for CA1s (mean 35.8 (SD 3.2) s vs. 57 (SD 3.2) s, P<0.0002) and a 26% decrease for CA2s (mean 23 (SD 1.7) s vs. 31 (SD 1.7) s, P=0.0118). Global skill score increased with warm-up by 4.8 points for CA1s (mean 32.8 (SD 1.2) vs. 37.6 (SD 1.2), P=0.0079) and 5.1 points for CA2s (37.7 (SD 1.1) vs. 42.8 (SD 1.1), P=0.0125). Crossover period and sequence did not show a statistically significant association with performance. CONCLUSIONS: Virtual warm-up significantly improved performance by residents of FOI in live patients with normal airway anatomy, as measured both by speed and by a scaled evaluation of skills.

Innate immunity including epithelial and nonspecific host factors: workshop 1B.

The majority of HIV infections are initiated at mucosal sites. The oral mucosal tissue has been shown to be a potential route of entry in humans and primates. Whereas HIV RNA, proviral DNA, and infected cells are detected in the oral mucosa and saliva of infected individuals, it appears that the oral mucosa is not permissive for efficient HIV replication and therefore may differ in susceptibility to infection when compared to other mucosal sites. Since there is no definitive information regarding the fate of the HIV virion in mucosal epithelium, there is a pressing need to understand what occurs when the virus is in contact with this tissue, what mechanisms are in play to determine the outcome, and to what degree the mechanisms and outcomes differ between mucosal sites. Workshop 1B tackled 5 important questions to define current knowledge about epithelial cell-derived innate immune agents, commensal and endogenous pathogens, and epithelial cells and cells of the adaptive immune system and how they contribute to dissemination or resistance to HIV infection. Discovering factors that explain the differential susceptibility and resistance to HIV infection in mucosal sites will allow for the identification and development of novel protective strategies.

Material modifications enhancing the antibacterial properties of two biodegradable poly(3-hydroxybutyrate) implants.

The aim of this study was to evaluate the antimicrobial efficacy of adding a gentamicin palmitate (GP) coating and zirconium dioxide (ZrO2) to biodegradable poly(3-hydroxybutyrate) (PHB) to reduce biofilm formation. Cylindrical pins with and without a coating were incubated in Müller-Hinton broth inoculated with 2 × 105 colony-forming units (CFU) ml-1 of Staphylococcus aureus for 2 d or 7 d, then sonicated to disrupt biofilms. Pure PHB (PHB + GP) and PHB pins with ZrO2 added (PHBzr + GP) were coated with GP and compared with PHB pins lacking a coating (PHB). Cells (CFU) were counted to quantify the number of bacteria in the biofilm and a cell proliferation assay was employed to evaluate metabolic activity, and scanning electron microscopy (SEM) was performed to visualize the structure of the biofilm. After 2 d of incubation there were significantly more cells in biofilms on PHB pins than PHB + GP and PHBzr + GP pins (p < 0.0001), and cells in the sonication fluid obtained from GP-coated pins exhibited significantly lower metabolic activity than cells from uncoated PHB pins (p < 0.0001). After 7 d of incubation metabolic activity was lowest for PHBzr + GP, with significant differences between PHB and PHBzr + GP (p = 0.001). SEM revealed more cells attached to the surface, and more structured biofilms, on pins without a coating. Coating pins with GP significantly reduced early biofilm formation on PHB implants. This could lower the potential risk of surgical site infections when using PHB implants. Addition of ZrO2 might further enhance the antibacterial properties. Such modification of the implant material should therefore be considered when developing new biodegradable PHB implants.

The role of zinc in the biocorrosion behavior of resorbable Mg‒Zn‒Ca alloys.

Zinc- and calcium-containing magnesium alloys, denominated ZX alloys, excel as temporary implant materials because of their composition made of physiologically essential minerals and lack of commonly used rare-earth alloying elements. This study documents the specific role of nanometric intermetallic particles (IMPs) on the in vitro and in vivo biocorrosion behavior of two ZX-lean alloys, Mg‒Zn1.0‒Ca0.3 (ZX10) and Mg‒Zn1.5‒Ca0.25 (ZX20) (in wt.%). These alloys were designed according to thermodynamic considerations by finely adjusting the nominal Zn content towards microstructures that differ solely in the type of phase composing the IMPs: ZX10, with 1.0 wt.% Zn, hosts binary Mg2Ca-phase IMPs, while ZX20, with 1.5 wt.% Zn, hosts ternary IM1-phase IMPs. Electrochemical methods and the hydrogen-gas evolution method were deployed and complemented by transmission electron microscopy analyses. These techniques used in concert reveal that the Mg2Ca-type IMPs anodically dissolve preferentially and completely, while the IM1-type IMPs act as nano-cathodes, facilitating a faster dissolution of ZX20 compared to ZX10. Additionally, a dynamically increasing cathodic reactivity with progressing dissolution was observed for both alloys. This effect is explained by redeposits of Zn on the corroding surface, which act as additional nano-cathodes and facilitate enhanced cathodic reaction kinetics. The higher degradation rate of ZX20 was verified in vivo via micro-computed tomography upon implantation of both materials into femurs of Sprague DawleyⓇ rats. Both alloys were well integrated with direct bone‒implant contact observable 4 weeks post operationem, and an appropriately slow and homogeneous degradation could be observed with no adverse effects on the surrounding tissue. The results suggest that both alloys qualify as new temporary implant materials, and that a minor adjustment of the Zn content may function as a lever for tuning the degradation rate towards desired applications. STATEMENT OF SIGNIFICANCE: In Mg‒Zn‒Ca (ZX)-lean alloys Zn is the most electropositive element, and thus requires special attention in the investigation of biocorrosion mechanisms acting on these alloys. Even a small increase of only 0.5 wt.% Zn is shown to accelerate the biodegradation rate in both simulated body conditions and in vivo. This is possible due to Zn's role in influencing the type of intermetallic particles (IMPs) in these alloys. These IMPs in turn, even though minute in size, are shown to govern the biocorrosion behavior on the macroscopic scale. The deep understanding gained in this study on the role of Zn and of the IMP type it governs is crucial to ensuring a safe and controllable implant degradation.

Transcriptome analysis of Porphyromonas gingivalis and Acinetobacter baumannii in polymicrobial communities.

Acinetobacter baumannii is a nosocomial, opportunistic pathogen that causes several serious conditions including meningitis, septicemia, endocarditis, and pneumonia. It can be found in the oral biofilm, which may be a reservoir for pneumonia and chronic obstructive pulmonary disease. Subgingival colonization by A. baumannii is associated with chronic and aggressive periodontitis as well as refractory periodontal disease. Porphyromonas gingivalis, a keystone periodontal pathogen localized to subgingival plaque, is also implicated in several chronic conditions including aspiration pneumonia. Although both bacteria are found together in subgingival plaque and can cause multiple polymicrobial infections, nothing is known about the interactions between these two important human pathogens. In this study, we used RNA sequencing to understand the transcriptional response of both species as they adapt to heterotypic communities. Among the differentially regulated genes were those encoding a number of important virulence factors for both species including adhesion, biofilm formation, and protein secretion. Additionally, the presence of A. baumannii increased the abundance of P. gingivalis in model dual-species communities. Collectively these results suggest that both P. gingivalis and A. baumannii adapt to each other and have synergistic potential for increased pathogenicity. In identifying the mechanisms that promote pathogenicity and refractory disease, novel approaches to mitigate polymicrobial synergistic interactions may be developed to treat or prevent associated diseases.

(C3) The oral epithelial cell and first encounters with HIV-1.

The oral epithelium is the site of first exposure of HIV-1 to host tissues during oral sex with an infected partner or through breast-feeding by an infected mother. Although the oral epithelium is distinguishable by its apparent resistance, the mucosal surfaces represent a primary target of HIV-1. After oral exposure and swallowing, infection is detected prominently in the gastrointestinal tract, which becomes depleted of CD4+ T-cells. The oral cavity and palatine tonsils appear to resist infection and transfer to susceptible lymphoid cells in the lamina propria by local anti-HIV-1 mechanisms. In some cases, expression of these antiviral mechanisms increases after exposure to HIV-1. During primary exposure and before seroconversion, based on limited in vitro and primate data, a window of opportunity for capture of HIV-1 by the oral epithelium may exist. After seroconversion, the risk of infectious HIV-1 appearing in saliva is negligible. This report considers evidence that oral epithelium has the potential both to enable and to resist infection by HIV-1.

Magnesium from bioresorbable implants: Distribution and impact on the nano- and mineral structure of bone.

Biocompatibility is a key issue in the development of new implant materials. In this context, a novel class of biodegrading Mg implants exhibits promising properties with regard to inflammatory response and mechanical properties. The interaction between Mg degradation products and the nanoscale structure and mineralization of bone, however, is not yet sufficiently understood. Investigations by synchrotron microbeam x-ray fluorescence (µXRF), small angle x-ray scattering (µSAXS) and x-ray diffraction (µXRD) have shown the impact of degradation speed on the sites of Mg accumulation in the bone, which are around blood vessels, lacunae and the bone marrow. Only at the highest degradation rates was Mg found at the implant-bone interface. The Mg inclusion into the bone matrix appeared to be non-permanent as the Mg-level decreased after completed implant degradation. µSAXS and µXRD showed that Mg influences the hydroxyl apatite (HAP) crystallite structure, because markedly shorter and thinner HAP crystallites were found in zones of high Mg concentration. These zones also exhibited a contraction of the HAP lattice and lower crystalline order.

Adhesive strength of bone-implant interfaces and in-vivo degradation of PHB composites for load-bearing applications.

Aim of this study was to evaluate the response of bone to novel biodegradable polymeric composite implants in the femora of growing rats. Longitudinal observation of bone reaction at the implant site (BV/TV) as well as resorption of the implanted pins were monitored using in vivo micro-focus computed tomography (µCT). After 12, 24 and 36 weeks femora containing the implants were explanted, scanned with high resolution ex vivo µCT, and the surface roughness of the implants was measured to conclude on the ingrowth capability for bone tissue. Scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDX) were used to observe changes on the surface of Polyhydroxybutyrate (PHB) during degradation and cell ingrowth. Four different composites with zirconium dioxide (ZrO2) and Herafill(®) were compared. After 36 weeks in vivo, none of the implants did show significant degradation. The PHB composite with ZrO2 and a high percentage (30%) of Herafill® as well as the Mg-alloy WZ21 showed the highest values of bone accumulation (increased BV/TV) around the implant. The lowest value was measured in PHB with 3% ZrO2 containing no Herafill®. Roughness measurements as well as EDX and SEM imaging could not reveal any changes on the PHB composites׳ surfaces. Biomechanical parameters, such as the adhesion strength between bone and implant were determined by measuring the shear strength as well as push-out energy of the bone-implant interface. The results showed that improvement of these mechanical properties of the studied PHBs P3Z, P3Z10H and P3Z30H is necessary in order to obtain appropriate load-bearing material. The moduli of elasticity, tensile strength and strain properties of the PHB composites are close to that of bone and thus promising. Compared to clinically used PLGA, PGA and PLA materials, their additional benefit is an unchanged local pH value during degradation, which makes them well tolerated by cells and immune system. They might be used successfully for personalized 3D printed implants or as coatings of rapidly dissolving implants.

Reaction of bone nanostructure to a biodegrading Magnesium WZ21 implant - A scanning small-angle X-ray scattering time study.

Understanding the implant-bone interaction is of prime interest for the development of novel biodegrading implants. Magnesium is a very promising material in the class of biodegrading metallic implants, owing to its mechanical properties and excellent immunologic response during healing. However, the influence of degrading Mg implants on the bone nanostructure is still an open question of crucial importance for the design of novel Mg implant alloys. This study investigates the changes in the nanostructure of bone following the application of a degrading WZ21 Mg implant (2wt% Y, 1wt% Zn, 0.25wt% Ca and 0.15wt% Mn) in a murine model system over the course of 15months by small angle X-ray scattering. Our investigations showed a direct response of the bone nanostructure after as little as 1month with a realignment of nano-sized bone mineral platelets along the bone-implant interface. The growth of new bone tissue after implant resorption is characterized by zones of lower mineral platelet thickness and slightly decreased order in the stacking of the platelets. The preferential orientation of the mineral platelets strongly deviates from the normal orientation along the shaft and still roughly follows the implant direction after 15months. We explain our findings by considering geometrical, mechanical and chemical factors during the process of implant resorption. STATEMENT OF SIGNIFICANCE: The advancement of surgical techniques and the increased life expectancy have caused a growing demand for improved bone implants. Ideally, they should be bio-resorbable, support bone as long as necessary and then be replaced by healthy bone tissue. Magnesium is a promising candidate for this purpose. Various studies have demonstrated its excellent mechanical performance, degradation behaviour and immunologic properties. The structural response of bone, however, is not well known. On the nanometer scale, the arrangement of collagen fibers and calcium mineral platelets is an important indicator of structural integrity. The present study provides insight into nanostructural changes in rat bone at different times after implant placement and different implant degradation states. The results are useful for further improved magnesium alloys.

Long-term in vivo degradation behavior and near-implant distribution of resorbed elements for magnesium alloys WZ21 and ZX50.

UNLABELLED: We report on the long-term effects of degrading magnesium implants on bone tissue in a growing rat skeleton using continuous in vivo micro-Computed Tomography, histological staining and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LA-ICP-MS). Two different magnesium alloys-one rapidly degrading (ZX50) and one slowly degrading (WZ21)-were used to evaluate the bone response and distribution of released Mg and Y ions in the femur of male Sprague-Dawley rats. Regardless of whether the alloy degrades rapidly or slowly, we found that bone recovers restitutio ad integrum after complete degradation of the magnesium implant. The degradation of the Mg alloys generates a significant increase in Mg concentration in the cortical bone near the remaining implant parts, but the Mg accumulation disappears after the implant degrades completely. The degradation of the Y-containing alloy WZ21 leads to Y enrichment in adjacent bone tissues and in newly formed bone inside the medullary space. Locally high Y concentrations suggest migration not only of Y ions but also of Y-containing intermetallic particles. However, after the full degradation of the implant the Y-enrichment disappears almost completely. Hydrogen gas formation and ion release during implant degradation did not harm bone regeneration in our samples. STATEMENT OF SIGNIFICANCE: Magnesium is generally considered to be one of the most attractive base materials for biodegradable implants, and many magnesium alloys have been optimized to adjust implant degradation. Delayed degradation, however, generates prolonged presence in the organism with the risk of foreign body reactions. While most studies so far have only ranged from several weeks up to 12months, the present study provides data for complete implant degradation and bone regeneration until 24months, for two magnesium alloys (ZX50, WZ21) with different degradation characteristics. µCT monitoring, histological staining and LA-ICP-MS illustrate the distribution of the elements in the neighboring bony tissues during implant degradation, and reveal in particular high concentrations of the rare-earth element Yttrium.

Influence of trace impurities on the in vitro and in vivo degradation of biodegradable Mg-5Zn-0.3Ca alloys.

The hydrogen evolution method and animal experiments were deployed to investigate the effect of trace impurity elements on the degradation behavior of high-strength Mg alloys of type ZX50 (Mg-5Zn-0.3Ca). It is shown that trace impurity elements increase the degradation rate, predominantly in the initial period of the tests, and also increase the material's susceptibility to localized corrosion attack. These effects are explained on the basis of the corrosion potential of the intermetallic phases present in the alloys. The Zn-rich phases present in ZX50 are nobler than the Mg matrix, and thus act as cathodic sites. The impurity elements Fe and Mn in the alloy of conventional purity are incorporated in these Zn-rich intermetallic phases and therefore increase their cathodic efficiency. A design rule for circumventing the formation of noble intermetallic particles and thus avoiding galvanically accelerated dissolution of the Mg matrix is proposed.

Expression of the antimicrobial peptide, human beta-defensin 1, in duct cells of minor salivary glands and detection in saliva.

The oral cavity is exposed to a variety of environmental insults. Salivary secretions play a critical role in maintaining oral health via innate host defense mechanisms and secretion of secretory IgA. Human beta-defensins (hBD) are antimicrobial peptides that are a component of the innate immune response; they are expressed in epithelia and are proposed to have a role in mucosal defense. hBD-1 mRNA is constitutively expressed in numerous mucosal tissues, including human gingiva and submandibular and parotid glands. Our objective was to detect the expression and localization of hBD-1 peptide in human salivary glands and in saliva. Minor salivary gland tissue was obtained from biopsies of patients with mucoceles (n = 20). hBD-1 peptide was detected by immunohistochemistry; expression was localized to the ductal cells and not the acinar cells of these glands. The peptide was located apically, toward the lumen in the duct cells. Further evaluation showed stronger hBD-1 expression in ducts with periductal inflammation, as indicated by the immunostaining of serial sections with anti-CD45 specific for B- and T-lymphocytes. Statistical analysis showed a strong correlation of hBD-1 staining and inflammation. Results of immunolocalization suggest that hBD-1 functions to protect salivary glands from retrograde infection, that expression of the peptide is enhanced in inflamed sites, and that post-transcriptional regulatory mechanisms may be involved in hBD-1 peptide expression. Western immunoblot analysis also detected hBD-1 peptide in unstimulated, whole, acidified saliva from normal volunteers. However, hBD-1 peptide associated with salivary mucin resulted in loss of the detection in a dot-immunoblot assay. Association of hBD-1 with salivary mucin may facilitate peptide distribution and adherence to oral surfaces and aid its function within the oral cavity.

Direct detection of Porphyromonas gingivalis in Macaca fascicularis dental plaque samples using an oligonucleotide probe.

Oligonucleotide probes complementary to the hypervariable regions of the 16S rRNA of Porphyromonas gingivalis, and previously shown to specifically identify human P. gingivalis strains to the species level, were tested for their ability to recognize P. gingivalis from nonhuman primates (Macaca fascicularis), either as distinct isolates or in subgingival dental plaque. The 32P-labeled probes hybridized with all 147 monkey isolates identified as P. gingivalis by morphology and biochemistry, but did not hybridize with any of the 331 isolates representing 17 genera of bacteria unrelated to P. gingivalis, or to the more closely related P. endodontalis and P. asaccharolytica. This corresponds to sensitivities and specificities of 100%. Of 76 M. fascicularis plaque samples, P. gingivalis was detected by probe and culture in 67. Of 26 human plaque samples taken from separate individuals free of periodontal disease, 23 failed to demonstrate P. gingivalis by probe or culture. The results of the combined 102 monkey and human plaque samples indicate that, when compared to culture as the "gold standard," the P. gingivalis probe had a sensitivity of 96%, a specificity of 87%, and an overall agreement with culture of 93%. These results reveal that the oligonucleotide probes used to identify P. gingivalis are specific for this organism, and give results comparable to culture methods for detecting the presence of P. gingivalis in M. fascicularis dental plaque.

Inflammatory cells and bacteria in pericoronal exudates from acute pericoronitis.

The present work is one in a series of studies carried out to verify the relationship between bacteria and gingival tissues in pericoronitis. Exudates from 6 cases of acute pericoronitis were examined by light and electron microscopy, including ultrathin sections and negative staining. While bacterial phagocytosis was prevalent in all the exudates studied, spirochetes, which were the predominant microorganisms, were not observed being phagocytized by PMNs or macrophages. The presence of spirochetes in pericoronitis as compared with acute necrotizing ulcerative gingivitis is discussed.

[Infection by cytomegalovirus in patients with acquired immunodeficiency syndrome (AIDS): clinical, virological, and histopathological correlations]. / Infecção pelo citomegalovírus em pacientes com síndrome da immunodeficiência adquirida (AIDS): relações clínico-virológicas e anatomopatológicas.

Between April 1986 and June 1987, 50 patients meeting the CDC criteria for AIDS were studied for serological and virological evidence of CMV infection. Attempts for virus isolation from peripheral blood, urine and saliva were performed in cell culture lines of human foreskin fibroblasts and CMV specific IgG and IgM were assayed by IFI and IgG by ELISA. A total of 121 blood, 119 urine and 96 saliva samples were collected. During the study period viremia was noted at least once in 12.5%, viruria in 23.2%, and excretion in saliva in 21.9%. When admitted in the study, 20% (10/50) of the patients had anti-CMV IgM antibodies and 100% (50/50) of them had IgG anti-CMV antibodies (IFI). Five of the 40 patients IgM negative at admission presented anti-CMV IgM antibodies during the study, suggesting CMV reactivation or reinfection. Active CMV infection based on virus isolation and/or IgM positivity was demonstrated in 60% of the patients. Histopathological studies were performed in 24 patients. CMV was found in 50% of the autopsies, mainly in the digestive system, lungs and adrenals. There was no correlation between clinical, virological (serology and isolation) and histopathological diagnosis.

[A decade of experience in craniofacial surgery].

Our craniofacial surgery team includes experts from the following fields: plastic surgery, neurosurgery, ophthalmology, genetics, neurology, orthodontics, pedodontics, facial rehabilitation, psychiatry, social work, anesthesiology and intensive care. Craniofacial surgery became to a large extent pediatric surgery, following evidence that careful, early surgery does not impair growth and that development following surgery is almost normal. The malformations that were repaired included those of the Crouzon and Apert syndromes, requiring frontal remodelling and advancement of the middle third of the facial skeleton; hypertelorism in which orbits were moved to the midline; large craniofacial clefts in which the hemiface from either side was moved to the midline; and different types of craniostenosis in which frontal advancement and remodelling with reconstruction of the vault was performed. The series consisted of 78 patients who presented between 1979-1989. 3 illustrative cases are described.

Characterization methods of bone-implant-interfaces of bioresorbable and titanium implants by fracture mechanical means.

Bioresorbable materials for implants have become increasingly researched over the last years. The bone-implant-interfaces of three different implant materials, namely a new bioresorbable magnesium alloy, a new self-reinforced polymer implant and a conventional titanium alloy, were tested using various methods: push-out tests, SEM and EDX analyses as well as surface analyses based on stereoscopic 3D pictures were conducted. The fracture energy is proposed as a very significant reference value for characterizing the mechanical performance of a bone-implant system. By using a video-extensometer system instead of, as is commonly done, tracking the movement of the crosshead in the push-out tests, the accuracy of measurement could be increased.

Interaction of Treponema denticola TD-4, GM-1, and MS25 with human gingival fibroblasts.

The adherence of Treponema denticola GM-1, TD-4, and MS25 to human gingival fibroblasts (HGFs) was studied to serve as an introduction to investigations into the interactions of these oral bacteria with human host cells. Under both aerobic (5% CO2) and anaerobic (85% N2 plus 10% H2 plus 5% CO2) environments, the interactions with the HGFs were such that strains GM-1 and MS25 were consistently more adherent than strain TD-4. Polyclonal antibodies to GM-1 inhibited GM-1 adherence by 70%, while MS25 and TD-4 showed differing degrees of cross-reactive inhibition, indicative of common but not identical epitopes on the surface of the three T. denticola strains. Pretreatment of the three strains with trypsin did not inhibit adherence; proteinase K did, however, inhibit this interaction by 80%. Trypsin pretreatment of the HGFs resulted in increases in adherence of 50 and 86% for GM-1 and MS25, respectively, while a decrease of 41% was noted for TD-4. Exposure of the T. denticola strains to sugars and lectin pretreatment of the HGFs implicated adherence mediation by mannose and galactose residues on the HGF surface. Periodate treatment of HGFs resulted in a 50% drop in adherence for GM-1 and MS25, but did not decrease that of TD-4. Addition of fetal bovine serum inhibited adherence of the three strains to differing degrees, with TD-4 being the most susceptible. Addition of purified fibronectin (100 micrograms/ml) resulted in greater than 50% inhibition in GM-1 and MS25 adherence, while a 25% increase occurred with TD-4. While strain differences were noted in some of the parameters studied, the results indicate two possibilities for T. denticola-HGF adherence: a lectinlike adhesin(s) on the T. denticola surface with affinity for galactose and mannose on the HGF surface, and a serum host factor(s) bridging T. denticola and HGFs.

Chemical and biological activities of a 64-kilodalton outer sheath protein from Treponema denticola strains.

This study examined the distribution of the major outer sheath proteins (MOSP) in several Treponema denticola strains and reports the isolation of a 64-kDa protein from the outer sheath of human clinical isolate T. denticola GM-1. The outer sheath was isolated by freeze-thaw procedures, and the distribution of outer sheath proteins was examined by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). T. denticola GM-1, MS25, SR-5, and three low-passage clinical isolates possessed an MOSP with a relative molecular mass of 60 to 64 kDa. This MOSP was absent in T. denticola ATCC 35404 (TD-4) and clinical isolate SR-4. The latter possessed an MOSP of 58 kDa. 125I labeling revealed both MOSP to be dissociated forms of higher-molecular-mass oligomeric units between 116 and 162 kDa. Two-dimensional SDS-PAGE confirmed the modifiability of these MOSP. Isoelectric focusing of the 64-kDa MOSP indicated a pI of 6.7. Immunoblots with antiserum to GM-1 whole cells revealed the 64-kDa protein to be immunogenic and not cross-reactive with the MOSP of TD-4 or SR-4, and monospecific antibody to the 64-kDa protein recognized common epitopes on the high-molecular-weight oligomeric protein. These antibodies did not react with any component of TD-4 whole cells in immunoblots or in immunogold electron microscopy. Fab fragments inhibited the adherence of T. denticola GM-1 to human gingival fibroblasts by 78% (1:1,600; 0.72 micrograms of protein per ml), while TD-4 adherence was not inhibited. Amino acid analysis revealed a slightly acidic protein, devoid of cysteine, with 36% hydrophobic residues. Cyanogen bromide fragmentation of the 64-kDa protein revealed that a 42-kDa fragment contained a T-L-D-L-A-L-D segment which was 100% homologous with an integrin alpha subunit of a human leukocyte adhesion glycoprotein p 150,95.