The development of bioresorbable composite polymeric implants with high mechanical strength.

Implants for the treatment of tissue defects should mimic the mechanical properties of the native tissue of interest and should be resorbable as well as biocompatible. In this work, we developed a scaffold from variants of poly(glycolic) acid which were braided and coated with an elastomer of poly(glycolide-co-caprolactone) and crosslinked. The coating of the scaffold with the elastomer led to higher mechanical strength in terms of compression, expansion and elasticity compared to braids without the elastomer coating. These composite scaffolds were found to have expansion properties similar to metallic stents, utilizing materials which are typically much weaker than metal. We optimized the mechanical properties of the implant by tuning the elastomer branching structure, crosslink density, and molecular weight. The scaffolds were shown to be highly resorbable following implantation in a porcine femoral artery. Biocompatibility was studied in vivo in an ovine model by implanting the scaffolds into femoral arteries. The scaffolds were able to support an expanded open lumen over 12 months in vivo and also fully resorbed by 18 months in the ovine model.

Fractionating Polymer Microspheres as Highly Accurate Density Standards.

This paper describes a method of isolating small, highly accurate density-standard beads and characterizing their densities using accurate and experimentally traceable techniques. Density standards have a variety of applications, including the characterization of density gradients, which are used to separate objects in a variety of fields. Glass density-standard beads can be very accurate (±0.0001 g cm(-3)) but are too large (3-7 mm in diameter) for many applications. When smaller density standards are needed, commercial polymer microspheres are often used. These microspheres have standard deviations in density ranging from 0.006 to 0.021 g cm(-3); these distributions in density make these microspheres impractical for applications demanding small steps in density. In this paper, commercial microspheres are fractionated using aqueous multiphase systems (AMPS), aqueous mixture of polymers and salts that spontaneously separate into phases having molecularly sharp steps in density, to isolate microspheres having much narrower distributions in density (standard deviations from 0.0003 to 0.0008 g cm(-3)) than the original microspheres. By reducing the heterogeneity in densities, this method reduces the uncertainty in the density of any specific bead and, therefore, improves the accuracy within the limits of the calibration standards used to characterize the distributions in density.

Combining Step Gradients and Linear Gradients in Density.

Combining aqueous multiphase systems (AMPS) and magnetic levitation (MagLev) provides a method to produce hybrid gradients in apparent density. AMPS­solutions of different polymers, salts, or surfactants that spontaneously separate into immiscible but predominantly aqueous phases­offer thermodynamically stable steps in density that can be tuned by the concentration of solutes. MagLev­the levitation of diamagnetic objects in a paramagnetic fluid within a magnetic field gradient­can be arranged to provide a near-linear gradient in effective density where the height of a levitating object above the surface of the magnet corresponds to its density; the strength of the gradient in effective density can be tuned by the choice of paramagnetic salt and its concentrations and by the strength and gradient in the magnetic field. Including paramagnetic salts (e.g., MnSO4 or MnCl2) in AMPS, and placing them in a magnetic field gradient, enables their use as media for MagLev. The potential to create large steps in density with AMPS allows separations of objects across a range of densities. The gradients produced by MagLev provide resolution over a continuous range of densities. By combining these approaches, mixtures of objects with large differences in density can be separated and analyzed simultaneously. Using MagLev to add an effective gradient in density also enables tuning the range of densities captured at an interface of an AMPS by simply changing the position of the container in the magnetic field. Further, by creating AMPS in which phases have different concentrations of paramagnetic ions, the phases can provide different resolutions in density. These results suggest that combining steps in density with gradients in density can enable new classes of separations based on density.

Disulfide-Based Diblock Copolymer Worm Gels: A Wholly-Synthetic Thermoreversible 3D Matrix for Sheet-Based Cultures.

It is well-known that 3D in vitro cell cultures provide a much better model than 2D cell cultures for understanding the in vivo microenvironment of cells. However, significant technical challenges in handling and analyzing 3D cell cultures remain, which currently limits their widespread application. Herein, we demonstrate the application of wholly synthetic thermoresponsive block copolymer worms in sheet-based 3D cell culture. These worms form a soft, free-standing gel reversibly at 20-37 °C, which can be rapidly converted into a free-flowing dispersion of spheres on cooling to 5 °C. Functionalization of the worms with disulfide groups was found to be essential for ensuring sufficient mechanical stability of these hydrogels to enable long-term cell culture. These disulfide groups are conveniently introduced via statistical copolymerization of a disulfide-based dimethacrylate under conditions that favor intramolecular cyclization and subsequent thiol/disulfide exchange leads to the formation of reversible covalent bonds between adjacent worms within the gel. This new approach enables cells to be embedded within micrometer-thick slabs of gel with good viability, permits cell culture for at least 12 days, and facilitates recovery of viable cells from the gel simply by incubating the culture in buffer at 4 °C (thus, avoiding the enzymatic degradation required for cell harvesting when using commercial protein-based gels, such as Matrigel).

Enrichment of reticulocytes from whole blood using aqueous multiphase systems of polymers.

This paper demonstrates the enrichment of reticulocytes by centrifuging whole blood through aqueous multiphase systems (AMPSs)-immiscible phases of solutions of polymers that form step-gradients in density. The interfaces of an AMPS concentrate cells; this concentration facilitates the extraction of blood enriched for reticulocytes. AMPS enrich reticulocytes from blood from both healthy and hemochromatosis donors. Varying the osmolality and density of the phases of AMPS provides different levels of enrichment and yield of reticulocytes. A maximum enrichment of reticulocytemia of 64 ± 3% was obtained from donors with hemochromatosis. When used on peripheral blood from normal donors, AMPS can provide a higher yield of enriched reticulocytes and a higher proportion of reticulocytes expressing CD71 than differential centrifugation followed by centrifugation over Percoll. Blood enriched for reticulocytes by AMPS could be useful for research on malaria. Several species of malaria parasites show a preference to invade young erythrocytes and reticulocytes; this preference complicates in vitro cultivation of these species in human blood. Plasmodium knowlesi malaria parasites invade normal human blood enriched for reticulocytes by AMPSs at a rate 2.2 times greater (P < 0.01) than they invade unenriched blood. Parasite invasion in normal blood enriched by AMPS was 1.8 times greater (P < 0.05) than in blood enriched to a similar reticulocytemia by differential centrifugation followed by centrifugation over Percoll. The enrichment of reticulocytes that are invaded by malaria parasites demonstrates that AMPSs can provide a label-free method to enrich cells for biological research.

Charging of multiple interacting particles by contact electrification.

Many processes involve the movement of a disordered collection of small particles (e.g., powders, grain, dust, and granular foods). These particles move chaotically, interact randomly among themselves, and gain electrical charge by contact electrification. Understanding the mechanisms of contact electrification of multiple interacting particles has been challenging, in part due to the complex movement and interactions of the particles. To examine the processes contributing to contact electrification at the level of single particles, a system was constructed in which an array of millimeter-sized polymeric beads of different materials were agitated on a dish. The dish was filled almost completely with beads, such that beads did not exchange positions. At the same time, during agitation, there was sufficient space for collisions with neighboring beads. The charge of the beads was measured individually after agitation. Results of systematic variations in the organization and composition of the interacting beads showed that three mechanisms determined the steady-state charge of the beads: (i) contact electrification (charging of beads of different materials), (ii) contact de-electrification (discharging of beads of the same charge polarity to the atmosphere), and (iii) a long-range influence across beads not in contact with one another (occurring, plausibly, by diffusion of charge from a bead with a higher charge to a bead with a lower charge of the same polarity).

The rate of charge tunneling is insensitive to polar terminal groups in self-assembled monolayers in Ag(TS)S(CH2)(n)M(CH2)(m)T//Ga2O3/EGaIn junctions.

This paper describes a physical-organic study of the effect of uncharged, polar, functional groups on the rate of charge transport by tunneling across self-assembled monolayer (SAM)-based large-area junctions of the form Ag(TS)S(CH2)(n)M(CH2)(m)T//Ga2O3/EGaIn. Here Ag(TS) is a template-stripped silver substrate, -M- and -T are "middle" and "terminal" functional groups, and EGaIn is eutectic gallium-indium alloy. Twelve uncharged polar groups (-T = CN, CO2CH3, CF3, OCH3, N(CH3)2, CON(CH3)2, SCH3, SO2CH3, Br, P(O)(OEt)2, NHCOCH3, OSi(OCH3)3), having permanent dipole moments in the range 0.5 < µ < 4.5, were incorporated into the SAM. A comparison of the electrical characteristics of these junctions with those of junctions formed from n-alkanethiolates led to the conclusion that the rates of charge tunneling are insensitive to the replacement of terminal alkyl groups with the terminal polar groups in this set. The current densities measured in this work suggest that the tunneling decay parameter and injection current for SAMs terminated in nonpolar n-alkyl groups, and polar groups selected from common polar organic groups, are statistically indistinguishable.

Adaptive use of bubble wrap for storing liquid samples and performing analytical assays.

This paper demonstrates that the gas-filled compartments in the packing material commonly called "bubble wrap" can be repurposed in resource-limited regions as containers to store liquid samples, and to perform bioanalyses. The bubbles of bubble wrap are easily filled by injecting the samples into them using a syringe with a needle or a pipet tip, and then sealing the hole with nail hardener. The bubbles are transparent in the visible range of the spectrum, and can be used as "cuvettes" for absorbance and fluorescence measurements. The interiors of these bubbles are sterile and allow storage of samples without the need for expensive sterilization equipment. The bubbles are also permeable to gases, and can be used to culture and store micro-organisms. By incorporating carbon electrodes, these bubbles can be used as electrochemical cells. This paper demonstrates the capabilities of the bubbles by culturing E. coli, growing C. elegans, measuring glucose and hemoglobin spectrophotometrically, and measuring ferrocyanide electrochemically, all within the bubbles.

Multigait soft robot.

This manuscript describes a unique class of locomotive robot: A soft robot, composed exclusively of soft materials (elastomeric polymers), which is inspired by animals (e.g., squid, starfish, worms) that do not have hard internal skeletons. Soft lithography was used to fabricate a pneumatically actuated robot capable of sophisticated locomotion (e.g., fluid movement of limbs and multiple gaits). This robot is quadrupedal; it uses no sensors, only five actuators, and a simple pneumatic valving system that operates at low pressures (< 10 psi). A combination of crawling and undulation gaits allowed this robot to navigate a difficult obstacle. This demonstration illustrates an advantage of soft robotics: They are systems in which simple types of actuation produce complex motion.

Structural transformation by electrodeposition on patterned substrates (STEPS): a new versatile nanofabrication method.

Arrays of high-aspect-ratio (HAR) nano- and microstructures are of great interest for designing surfaces for applications in optics, bio-nano interfaces, microelectromechanical systems, and microfluidics, but the difficulty of systematically and conveniently varying the geometries of these structures significantly limits their design and optimization for a specific function. This paper demonstrates a low-cost, high-throughput benchtop method that enables a HAR array to be reshaped with nanoscale precision by electrodeposition of conductive polymers. The method-named STEPS (structural transformation by electrodeposition on patterned substrates)-makes it possible to create patterns with proportionally increasing size of original features, to convert isolated HAR features into a closed-cell substrate with a continuous HAR wall, and to transform a simple parent two-dimensional HAR array into new three-dimensional patterned structures with tapered, tilted, anisotropic, or overhanging geometries by controlling the deposition conditions. We demonstrate the fabrication of substrates with continuous or discrete gradients of nanostructure features, as well as libraries of various patterns, starting from a single master structure. By providing exemplary applications in plasmonics, bacterial patterning, and formation of mechanically reinforced structures, we show that STEPS enables a wide range of studies of the effect of substrate topography on surface properties leading to optimization of the structures for a specific application. This research identifies solution-based deposition of conductive polymers as a new tool in nanofabrication and allows access to 3D architectures that were previously difficult to fabricate.

Contact de-electrification of electrostatically charged polymers.

The contact electrification of insulating organic polymers is still incompletely understood, in part because multiple fundamental mechanisms may contribute to the movement of charge. This study describes a mechanism previously unreported in the context of contact electrification: that is, "contact de-electrification", a process in which polymers charged to the same polarity discharge on contact. Both positively charged polymeric beads, e.g., polyamide 6/6 (Nylon) and polyoxymethylene (Delrin), and negatively charged polymeric beads, e.g., polytetrafluoroethylene (Teflon) and polyamide-imide (Torlon), discharge when the like-charged beads are brought into contact. The beads (both with charges of ∼±20 µC/m(2), or ∼100 charges/µm(2)) discharge on contact regardless of whether they are made of the same material, or of different materials. Discharge is rapid: discharge of flat slabs of like-charged Nylon and Teflon pieces is completed on a single contact (∼3 s). The charge lost from the polymers during contact de-electrification transfers onto molecules of gas in the atmosphere. When like-charged polymers are brought into contact, the increase in electric field at the point of contact exceeds the dielectric breakdown strength of the atmosphere and ionizes molecules of the gas; this ionization thus leads to discharge of the polymers. The detection (using a Faraday cup) of charges transferred to the cup by the ionized gas is compatible with the mechanism. Contact de-electrification occurs for different polymers and in atmospheres with different values of dielectric breakdown strength (helium, argon, oxygen, carbon dioxide, nitrogen, and sulfur hexafluoride): the mechanism thus appears to be general.

Aqueous multiphase systems of polymers and surfactants provide self-assembling step-gradients in density.

This Communication demonstrates the generation of over 300 phase-separated systems-ranging from two to six phases-from mixtures of aqueous solutions of polymers and surfactants. These aqueous multiphase systems (MuPSs) form self-assembling, thermodynamically stable step-gradients in density using a common solvent, water. The steps in density between phases of a MuPS can be very small (Δρ ≈ 0.001 g/cm(3)), do not change over time, and can be tuned by the addition of co-solutes. We use two sets of similar objects, glass beads and pellets of different formulations of Nylon, to demonstrate the ability of MuPSs to separate mixtures of objects by differences in density. The stable interfaces between phases facilitate the convenient collection of species after separation. These results suggest that the stable, sharp step-gradients in density provided by MuPSs can enable new classes of fractionations and separations based on density.

Replacing -CH2CH2- with -CONH- does not significantly change rates of charge transport through Ag(TS)-SAM//Ga2O3/EGaIn junctions.

This paper describes physical-organic studies of charge transport by tunneling through self-assembled monolayers (SAMs), based on systematic variations of the structure of the molecules constituting the SAM. Replacing a -CH(2)CH(2)- group with a -CONH- group changes the dipole moment and polarizability of a portion of the molecule and has, in principle, the potential to change the rate of charge transport through the SAM. In practice, this substitution produces no significant change in the rate of charge transport across junctions of the structure Ag(TS)-S(CH(2))(m)X(CH(2))(n)H//Ga(2)O(3)/EGaIn (TS = template stripped, X = -CH(2)CH(2)- or -CONH-, and EGaIn = eutectic alloy of gallium and indium). Incorporation of the amide group does, however, increase the yields of working (non-shorting) junctions (when compared to n-alkanethiolates of the same length). These results suggest that synthetic schemes that combine a thiol group on one end of a molecule with a group, R, to be tested, on the other (e.g., HS~CONH~R) using an amide-based coupling provide practical routes to molecules useful in studies of molecular electronics.

Magnetic levitation as a platform for competitive protein-ligand binding assays.

This paper describes a method based on magnetic levitation (MagLev) that is capable of indirectly measuring the binding of unlabeled ligands to unlabeled protein. We demonstrate this method by measuring the affinity of unlabeled bovine carbonic anhydrase (BCA) for a variety of ligands (most of which are benzene sulfonamide derivatives). This method utilizes porous gel beads that are functionalized with a common aryl sulfonamide ligand. The beads are incubated with BCA and allowed to reach an equilibrium state in which the majority of the immobilized ligands are bound to BCA. Since the beads are less dense than the protein, protein binding to the bead increases the overall density of the bead. This change in density can be monitored using MagLev. Transferring the beads to a solution containing no protein creates a situation where net protein efflux from the bead is thermodynamically favorable. The rate at which protein leaves the bead for the solution can be calculated from the rate at which the levitation height of the bead changes. If another small molecule ligand of BCA is dissolved in the solution, the rate of protein efflux is accelerated significantly. This paper develops a reaction-diffusion (RD) model to explain both this observation, and the physical-organic chemistry that underlies it. Using this model, we calculate the dissociation constants of several unlabeled ligands from BCA, using plots of levitation height versus time. Notably, although this method requires no electricity, and only a single piece of inexpensive equipment, it can measure accurately the binding of unlabeled proteins to small molecules over a wide range of dissociation constants (K(d) values within the range from ~10 nM to 100 µM are measured easily). Assays performed using this method generally can be completed within a relatively short time period (20 min-2 h). A deficiency of this system is that it is not, in its present form, applicable to proteins with molecular weight greater than approximately 65 kDa.

Analog modeling of Worm-Like Chain molecules using macroscopic beads-on-a-string.

This paper describes an empirical model of polymer dynamics, based on the agitation of millimeter-sized polymeric beads. Although the interactions between the particles in the macroscopic model and those between the monomers of molecular-scale polymers are fundamentally different, both systems follow the Worm-Like Chain theory.

Folding of electrostatically charged beads-on-a-string as an experimental realization of a theoretical model in polymer science.

The "beads-on-a-string" model for folding of polymers is a cornerstone of theoretical polymer science. This communication describes a physical model of beads-on-a-string, based on the folding of flexible strings of electrostatically charged beads in two dimensions. The system comprises millimeter-scale Teflon and Nylon-6,6 (spherical or cylindrical) beads (approximately 6 mm in diameter) separated by smaller (approximately 3 mm) poly(methyl methacrylate) (PMMA) spherical beads, threaded on a flexible string. The smaller, uncharged beads define the distances between the larger beads, and control the flexibility of the string. During agitation of the sequence of beads on a planar, horizontal paper surface, tribocharging generates opposite electrostatic charges on the larger Nylon and Teflon beads, but leaves the smaller PMMA beads essentially uncharged; the resulting electrostatic interactions cause the string to fold. Examination and comparison of two models--one physical and one theoretical--may offer a new approach to understanding folding, collapse, and molecular recognition at an abstract level, with particular opportunity to explore the influence of the flexibility of the string and the shape of the beads on the pattern and rate of folding. The physical system is, thus, an analog computer, simulating the theoretical beads-on-a-string model in two dimensions; this system makes it possible to test hypotheses connecting "sequence" to "folding", rapidly and conveniently, while exploring nonlinearities and other complexities omitted from the theoretical model.

Infochemistry and infofuses for the chemical storage and transmission of coded information.

This article describes a self-powered system that uses chemical reactions--the thermal excitation of alkali metals--to transmit coded alphanumeric information. The transmitter (an "infofuse") is a strip of the flammable polymer nitrocellulose patterned with alkali metal ions; this pattern encodes the information. The wavelengths of 2 consecutive pulses of light represent each alphanumeric character. While burning, infofuses transmit a sequence of pulses (at 5-20 Hz) of atomic emission that correspond to the sequence of metallic salts (and therefore to the encoded information). This system combines information technology and chemical reactions into a new area--"infochemistry"--that is the first step toward systems that combine sensing and transduction of chemical signals with multicolor transmission of alphanumeric information.

Cofabrication: a strategy for building multicomponent microsystems.

This Account describes a strategy for fabricating multicomponent microsystems in which the structures of essentially all of the components are formed in a single step of micromolding. This strategy, which we call "cofabrication", is an alternative to multilayer microfabrication, in which multiple layers of components are sequentially aligned ("registered") and deposited on a substrate by photolithography. Cofabrication has several characteristics that make it an especially useful approach for building multicomponent microsystems. It rapidly and inexpensively generates correctly aligned components (for example, wires, heaters, magnetic field generators, optical waveguides, and microfluidic channels) over very large surface areas. By avoiding registration, the technique does not impose on substrates the size limitations of common registrations tools, such as steppers and contact aligners. We have demonstrated multicomponent microsystems with surface areas exceeding 100 cm(2), but in principle, device size is only limited by the requirements of generating the original master. In addition, cofabrication can serve as a low-cost strategy for building microsystems. The technique is amenable to a variety of laboratory settings and uses fabrication tools that are less expensive than those used for multistep microfabrication. Moreover, the process requires only small amounts of solvent and photoresist, a costly chemical required for photolithography; in cofabrication, photoresist is applied and developed only once to produce a master, which is then used to produce multiple copies of molds containing the microfluidic channels. From a broad perspective, cofabrication represents a new processing paradigm in which the exterior (or shell) of the desired structures are produced before the interior (or core). This approach, generating the insulation or packaging structure first and injecting materials that provide function in channels in liquid phase, makes it possible to design and build microsystems with component materials that cannot be easily manipulated conventionally (such as solid materials with low melting points, liquid metals, liquid crystals, fused salts, foams, emulsions, gases, polymers, biomaterials, and fragile organics). Moreover, materials can be altered, removed, or replaced after the manufacturing stage. For example, cofabrication allows one to build devices in which a liquid flows through the device during use, or is replaced after use. Metal wires can be melted and reset by heating (in principle, repairing a break). This method leads to certain kinds of structures, such as integrated metallic wires with large cross-sectional areas or optical waveguides aligned in the same plane as microfluidic channels, that would be difficult or impossible to make with techniques such as sputter deposition or evaporation. This Account outlines the strategy of cofabrication and describes several applications. Specifically, we highlight cofabricated systems that combine microfluidics with (i) electrical wires for microheaters, electromagnets, and organic electrodes, (ii) fluidic optical components, such as optical waveguides, lenses, and light sources, (iii) gels for biological cell cultures, and (iv) droplets for compartmentalized chemical reactions, such as protein crystallization.

Transistors formed from a single lithography step using information encoded in topography.

This paper describes a strategy for the fabrication of functional electronic components (transistors, capacitors, resistors, conductors, and logic gates but not, at present, inductors) that combines a single layer of lithography with angle-dependent physical vapor deposition; this approach is named topographically encoded microlithography (abbreviated as TEMIL). This strategy extends the simple concept of 'shadow evaporation' to reduce the number and complexity of the steps required to produce isolated devices and arrays of devices, and eliminates the need for registration (the sequential stacking of patterns with correct alignment) entirely. The defining advantage of this strategy is that it extracts information from the 3D topography of features in photoresist, and combines this information with the 3D information from the angle-dependent deposition (the angle and orientation used for deposition from a collimated source of material), to create 'shadowed' and 'illuminated' regions on the underlying substrate. It also takes advantage of the ability of replica molding techniques to produce 3D topography in polymeric resists. A single layer of patterned resist can thus direct the fabrication of a nearly unlimited number of possible shapes, composed of layers of any materials that can be deposited by vapor deposition. The sequential deposition of various shapes (by changing orientation and material source) makes it possible to fabricate complex structures-including interconnected transistors-using a single layer of topography. The complexity of structures that can be fabricated using simple lithographic features distinguishes this procedure from other techniques based on shadow evaporation.

Controlling the orientation and synaptic differentiation of myotubes with micropatterned substrates.

Micropatterned poly(dimethylsiloxane) substrates fabricated by soft lithography led to large-scale orientation of myoblasts in culture, thereby controlling the orientation of the myotubes they formed. Fusion occurred on many chemically identical surfaces in which varying structures were arranged in square or hexagonal lattices, but only a subset of patterned surfaces yielded aligned myotubes. Remarkably, on some substrates, large populations of myotubes oriented at a reproducible acute angle to the lattice of patterned features. A simple geometrical model predicts the angle and extent of orientation based on maximizing the contact area between the myoblasts and patterned topographic surfaces. Micropatterned substrates also provided short-range cues that influenced higher-order functions such as the localization of focal adhesions and accumulation of postsynaptic acetylcholine receptors. Our results represent what we believe is a new approach for musculoskeletal tissue engineering, and our model sheds light on mechanisms of myotube alignment in vivo.