Modification of pore-wall in direct ink writing wollastonite scaffolds favorable for tuning biodegradation and mechanical stability and enhancing osteogenic capability.

Surface chemistry and mechanical stability determine the osteogenic capability of bone implants. The development of high-strength bioactive scaffolds for in-situ repair of large bone defects is challenging because of the lack of satisfying biomaterials. In this study, highly bioactive Ca-silicate (CSi) bioceramic scaffolds were fabricated by additive manufacturing and then modified for pore-wall reinforcement. Pure CSi scaffolds were fabricated using a direct ink writing technique, and the pore-wall was modified with 0%, 6%, or 10% Mg-doped CSi slurry (CSi, CSi-Mg6, or CSi-Mg10) through electrostatic interaction. Modified CSi@CSi-Mg6 and CSi@CSi-Mg10 scaffolds with over 60% porosity demonstrated an appreciable compressive strength beyond 20 MPa, which was ~2-fold higher than that of pure CSi scaffolds. CSi-Mg6 and CSi-Mg10 coating layers were specifically favorable for retarding bio-dissolution and mechanical decay of scaffolds in vitro. In-vivo investigation of critical-size femoral bone defects repair revealed that CSi@CSi-Mg6 and CSi@CSi-Mg10 scaffolds displayed limited biodegradation, accelerated new bone ingrowth (4-12 weeks), and elicited a suitable mechanical response. In contrast, CSi scaffolds exhibited fast biodegradation and retarded new bone regeneration after 8 weeks. Thus, tailoring of the chemical composition of pore-wall struts of CSi scaffolds is beneficial for enhancing the biomechanical properties and bone repair efficacy.

Preparation and In Vitro Biological Evaluation of Octacalcium Phosphate/Bioactive Glass-Chitosan/ Alginate Composite Membranes Potential for Bone Guided Regeneration.

The chitosan/alginate-trace element-codoped octacalcium phosphate/nano-sized bioactive glass (CS/ALG-teOCP/nBG) composite membranes were prepared by a layer-by-layer coating method for the functional requirement of guided bone regeneration (GBR). The morphology, mechanical properties and moisture content of the membranes was studied by scanning electron microscopy (SEM) observation, mechanical and swelling test. The results showed that the teOCP/nBG distributed uniformly in the composite membranes, and such as-prepared composite membrane exhibited an excellent tensile strength, accompanying with mechanical decay with immersion in aqueous medium. Cell culture and MTT assays showed that the surface microstructure and the ion dissolution products from teOCP/nBG components could enhance the cell proliferation, and especially the composite membranes was suitable for supporting the adhesion and growth behavior of human bone marrow mesenchymal stem cells (hBMSCs) in comparison with the CS/ALG pure polymer membranes. These results suggest that the new CS/ALG-teOCP/nBG composite membrane is highly bioactive and biodegradable, and favorable for guiding bone regeneration.

Bioceramic scaffolds with two-step internal/external modification of copper-containing polydopamine enhance antibacterial and alveolar bone regeneration capability. / å«é“œèšå¤šå·´èƒºå† å¤–åŒä¿®é¥°æ³•æž„å»ºæŠ—èŒä¿ƒéª¨å†ç”Ÿç”Ÿç‰©é™¶ç“·æ”¯æž¶.

Magnesium-doped calcium silicate (CS) bioceramic scaffolds have unique advantages in mandibular defect repair; however, they lack antibacterial properties to cope with the complex oral microbiome. Herein, for the first time, the CS scaffold was functionally modified with a novel copper-containing polydopamine (PDA(Cu2+|)) rapid deposition method, to construct internally modified (*P), externally modified (@PDA), and dually modified (*P@PDA) scaffolds. The morphology, degradation behavior, and mechanical properties of the obtained scaffolds were evaluated in vitro. The results showed that the CS*P@PDA had a unique micro-/nano-structural surface and appreciable mechanical resistance. During the prolonged immersion stage, the release of copper ions from the CS*P@PDA scaffolds was rapid in the early stage and exhibited long-term sustained release. The in vitro evaluation revealed that the release behavior of copper ions ascribed an excellent antibacterial effect to the CS*P@PDA, while the scaffolds retained good cytocompatibility with improved osteogenesis and angiogenesis effects. Finally, the PDA(Cu2+)-modified scaffolds showed effective early bone regeneration in a critical-size rabbit mandibular defect model. Overall, it was indicated that considerable antibacterial property along with the enhancement of alveolar bone regeneration can be imparted to the scaffold by the two-step PDA(Cu2+) modification, and the convenience and wide applicability of this technique make it a promising strategy to avoid bacterial infections on implants.

Preferentially Biodegradable Gypsum Fibers Endowing Invisible Microporous Structures and Enhancing Osteogenic Capability of Calcium Phosphate Cements.

It is known that hydroxyapatite-type calcium phosphate cement (CPC) shows appreciable self-curing properties, but the phase transformation products often lead to slow biodegradation and disappointing osteogenic responses. Herein, we developed an innovative strategy to endow invisible micropore networks, which could tune the microstructures and biodegradation of α-tricalcium phosphate (α-TCP)-based CPC by gypsum fibers, and the osteogenic capability of the composite cements could be enhanced in vivo. The gypsum fibers were prepared via extruding the gypsum powder/carboxylated chitosan (CC) slurry through a 22G nozzle (410 µm in diameter) and collecting with a calcium salt solution. Then, the CPCs were prepared by mixing the α-TCP powder with gypsum fibers (0-24 wt %) and an aqueous solution to form self-curing cements. The physicochemical characterizations showed that injectability was decreased with an increase in the fiber contents. The µCT reconstruction demonstrated that the gypsum fiber could be distributed in the CPC substrate and produce long-range micropore architectures. In particular, incorporation of gypsum fibers would tune the ion release, produce tunnel-like pore networks in vitro, and promote new bone tissue regeneration in rabbit femoral bone defects in vivo. Appropriate gypsum fibers (16 and 24 wt %) could enhance bone defect repair and cement biodegradation. These results demonstrate that the highly biodegradable cement fibers could mediate the microstructures of conventional CPC biomaterials, and such a bicomponent composite strategy may be beneficial for expanding clinical CPC-based applications.

Customized bioceramic scaffolds and metal meshes for challenging large-size mandibular bone defect regeneration and repair.

Large-size mandible graft has huge needs in clinic caused by infection, tumor, congenital deformity, bone trauma and so on. However, the reconstruction of large-size mandible defect is challenged due to its complex anatomical structure and large-range bone injury. The design and fabrication of porous implants with large segments and specific shapes matching the native mandible remain a considerable challenge. Herein, the 6% Mg-doped calcium silicate (CSi-Mg6) and ß- and α-tricalcium phosphate (ß-TCP, α-TCP) bioceramics were fabricated by digital light processing as the porous scaffolds of over 50% in porosity, while the titanium mesh was fabricated by selective laser melting. The mechanical tests showed that the initial flexible/compressive resistance of CSi-Mg6 scaffolds was markedly higher than that of ß-TCP and α-TCP scaffolds. Cell experiments showed that these materials all had good biocompatibility, while CSi-Mg6 significantly promoted cell proliferation. In the rabbit critically sized mandible bone defects (∼13 mm in length) filled with porous bioceramic scaffolds, the titanium meshes and titanium nails were acted as fixation and load bearing. The results showed that the defects were kept during the observation period in the blank (control) group; in contrast, the osteogenic capability was significantly enhanced in the CSi-Mg6 and α-TCP groups in comparison with the ß-TCP group, and these two groups not only had significantly increased new bone formation but also had thicker trabecular and smaller trabecular spacing. Besides, the CSi-Mg6 and α-TCP groups showed appreciable material biodegradation in the later stage (from 8 to 12 weeks) in comparison with the ß-TCP scaffolds while the CSi-Mg6 group showed much outstanding mechanical capacity in vivo in the early stage compared to the ß-TCP and α-TCP groups. Totally, these findings suggest that the combination of customized strength-strong bioactive CSi-Mg6 scaffolds together with titanium meshes is a promising way for repairing the large-size load-bearing mandible defects.

Fast self-curing α-tricalcium phosphate/ß-dicalcium silicate composites beneficial for root canal sealing treatment.

Objectives: α-tricalcium phosphate (α-TCP) and ß-dicalcium silicate (ß-C2S) have attracted much attention since these two types of self-curing Ca-phosphate and Ca-silicate are valuable biomaterials for bone defect or endodontic therapy. However, the injectable paste of their individual with high liquid/solid ratio is junior for root canal sealing due to very long self-setting time, low pH value and/or much volume shrinkage during paste-to-cement transformation. Methods: Our studies evaluated the effect of biphasic ratio, liquid/solid ratio and pH condition of aqueous medium on setting time and mechanical strength of this biphasic composite cement, and also the hydroxyapatite re-mineralization potential and anti-microleakage level of the cements with different α-TCP/ß-C2S ratio were explored in vitro. A control group free of paste filler was included in the extracted teeth model. Dentine re-mineralization and microleakage degree were observed by scanning electron microscopy and microCT reconstruction analysis. Results: It indicated that the weak acidic solution with pH value of 6.0 may produce a significantly shorter initial setting time (from 90 min to less 20 min) and expected final setting time (<150 min) for the biphasic composite (2:1 or 1:2) in comparison with the pure ß-C2S. Notably, the phasic composites exhibited limited microleakage and induced hydroxyapatite mineralization in the dentine tubules. These hydraulic pastes also produced strong alkaline feature and appreciable compressive resistance (12-18 MPa) after setting for a very short time stage. Moreover, a link between the addition of α-TCP leading to fast re-mineralization reaction was established. Significance: Our findings suggest that the appreciable self-setting and physicochemical properties adaption to root canal sealability make α-TCP/ß-C2S composites as preferential candidates for endodontic treatments.

3D printed bioceramic scaffolds: Adjusting pore dimension is beneficial for mandibular bone defects repair.

Bioceramic scaffolds for repairing mandibular bone defects have considerable effects, whereas pore architecture in porous scaffolds on osteogenesis in specific structures is still controversial. Herein 6 mol% magnesium-substituted calcium silicate scaffolds were fabricated with similar porosity (∼58%) but different cylindrical pore dimensions (Ø 480, 600, and 720 µm) via digital light processing-based three-dimensional (3D) printing technique. The mechanical properties, bioactive ion release, and bio-dissolution of the bioceramic scaffolds were evaluated in vitro, and the facilitation of scaffolds on bone formation was investigated after implanting in vivo. The results showed that as the pore dimension increased, the scaffolds indicated similar surface microstructures, but their compressive strength was enhanced gradually. There was no significant difference in vitro bio-dissolution between the 480 and 600 µm groups, whereas the 720 µm group showed a much slower dissolution and ion release. Interestingly, the two-dimensional/three-dimensional (2D/3D) micro-CT reconstruction analysis of rabbits' mandibular bone defects model showed that the 600 µm group exhibited evidently higher ratio of the newly formed bone volume to total volume (BV/TV) and trabecular number (Tb. N) values and lower ratio of the scaffolds residual volume to total volume (RV/TV) compare to the other two sizes. Furthermore, the histological analysis also revealed a considerably higher new bone ingrowth rate in the 600 µm group than the other two groups at 4-12 weeks post-implantation. Totally, it is proved from these experimental studies that the DLP-based accurately fabricated calcium (Ca) silicate bioceramic scaffolds with appropriate pore dimensions (i.e., 600 µm in pore size) are promising to guide new bone ingrowth and thus accelerate the regeneration and repair of cranial maxillofacial or periodontal bone defects.

Modularized bioceramic scaffold/hydrogel membrane hierarchical architecture beneficial for periodontal tissue regeneration in dogs.

BACKGROUND: Destruction of alveolar bone and periodontal ligament due to periodontal disease often requires surgical treatment to reconstruct the biological construction and functions of periodontium. Despite significant advances in dental implants in the past two decades, it remains a major challenge to adapt bone grafts and barrier membrane in surgery due to the complicated anatomy of tooth and defect contours. Herein, we developed a novel biphasic hierarchical architecture with modularized functions and shape based on alveolar bone anatomy to achieve the ideal outcomes. METHODS: The integrated hierarchical architecture comprising of nonstoichiometric wollastonite (nCSi) scaffolds and gelatin methacrylate/silanized hydroxypropyl methylcellulose (GelMA/Si-HPMC) hydrogel membrane was fabricated by digital light processing (DLP) and photo-crosslinked hydrogel injection technique respectively. The rheological parameters, mechanical properties and degradation rates of composite hydrogels were investigated. L-929 cells were cultured on the hydrogel samples to evaluate biocompatibility and cell barrier effect. Cell scratch assay, alkaline phosphatase (ALP) staining, and alizarin red (AR) staining were used to reveal the migration and osteogenic ability of hydrogel membrane based on mouse mandible-derived osteoblasts (MOBs). Subsequently, a critical-size one-wall periodontal defect model in dogs was prepared to evaluate the periodontal tissue reconstruction potential of the biphasic hierarchical architecture. RESULTS: The personalized hydrogel membrane integrating tightly with the nCSi scaffolds exhibited favorable cell viability and osteogenic ability in vitro, while the scratch assay showed that osteoblast migration was drastically correlated with Si-HPMC content in the composite hydrogel. The equivalent composite hydrogel has proven good physiochemical properties, and its membrane exhibited potent occlusive effect in vivo; meanwhile, the hierarchical architectures exerted a strong periodontal regeneration capability in the periodontal intrabony defect models of dogs. Histological examination showed effective bone and periodontal ligament regeneration in the biomimetic architecture system; however, soft tissue invasion was observed in the control group. CONCLUSIONS: Our results suggested that such modularized hierarchical architectures have excellent potential as a next-generation oral implants, and this precisely tuned guided tissue regeneration route offer an opportunity for improving periodontal damage reconstruction and reducing operation sensitivity.

A new injectable quick hardening anti-collapse bone cement allows for improving biodegradation and bone repair.

The development of injectable cement-like biomaterials via a minimally invasive approach has always attracted considerable clinical interest for modern bone regeneration and repair. Although α-tricalcium phosphate (α-TCP) powders may readily react with water to form hydraulic calcium-deficient hydroxyapatite (CDHA) cement, its long setting time, poor anti-collapse properties, and low biodegradability are suboptimal for a variety of clinical applications. This study aimed to develop new injectable α-TCP-based bone cements via strontium doping, α-calcium sulfate hemihydrate (CSH) addition and liquid phase optimization. A combination of citric acid and chitosan was identified to facilitate the injectable and anti-washout properties, enabling higher resistance to structure collapse. Furthermore, CSH addition (5 %-15 %) was favorable for shortening the setting time (5-20 min) and maintaining the compressive strength (10-14 MPa) during incubation in an aqueous buffer medium. These α-TCP-based composites could also accelerate the biodegradation rate and new bone regeneration in rabbit lateral femoral bone defect models in vivo. Our studies demonstrate that foreign ion doping, secondary phase addition and liquid medium optimization could synergistically improve the physicochemical properties and biological performance of α-TCP-based bone cements, which will be promising biomaterials for repairing bone defects in situations of trauma and diseased bone.

Precisely Tuning the Pore-Wall Surface Composition of Bioceramic Scaffolds Facilitates Angiogenesis and Orbital Bone Defect Repair.

Orbital bone damage (OBD) may result in severe post-traumatic enophthalmos, craniomaxillofacial deformities, vision loss, and intracranial infections. However, it is still a challenge to fabricate advanced biomaterials that can match the individual anatomical structure and enhance OBD repair in situ. Herein, we aimed to develop a selective surface modification strategy on bioceramic scaffolds and evaluated the effects of inorganic or organic functional coating on angiogenesis and osteogenesis, ectopically and orthotopically in OBD models. It was shown that the low thermal bioactive glass (BG) modification or layer-by-layer assembly of a biomimetic hydrogel (Biogel) could readily integrate into the pore wall of the bioceramic scaffolds. The BG and Biogel modification showed appreciable enhancement in the initial compressive strength (∼30-75%) or structural stability in vivo, respectively. BG modification could enhance by nearly 2-fold the vessel ingrowth, and the osteogenic capacity was also accelerated, accompanied with a mild scaffold biodegradation after 3 months. Meanwhile, the Biogel-modified scaffolds showed enhanced osteogenic differentiation and mineralization through calcium and phosphorus retention. The potential mechanism of the enhanced bone repair was elucidated via vascular and osteogenic cell responses in vitro, and the cell tests indicated that the Biogel and BG functional layers were both beneficial for in vitro osteoblastic differentiation and mineralization on bioceramics. Totally, these findings demonstrated that the bioactive ions or biomolecules could significantly improve the angiogenic and osteogenic capabilities of conventional bioceramics, and the integration of inorganic or organic functional coating in the pore wall is a highly flexible material toolbox that can be tailored directly to improve orbital bone defect repair.

Artificial osteochondral interface of bioactive fibrous membranes mediating calcified cartilage reconstruction.

Calcified cartilage is a mineralized osteochondral interface region between the hyaline cartilage and subchondral bone. There are few reported artificial biomaterials that could offer bioactivities for substantial reconstruction of calcified cartilage. Herein we developed new poly(L-lactide-co-caprolactone) (PLCL)-based trilayered fibrous membranes as a functional interface for calcified cartilage reconstruction and superficial cartilage restoration. The trilayered membranes were prepared by the electrospinning technique, and the fibrous morphology was maintained when the chondroitin sulfate (CS) or bioactive glass (BG) particles were introduced in the upper or bottom layer, respectively. Although 30% BG in the bottom layer led to a significant decrease in tensile resistance, the inorganic ion release was remarkably higher than that in the counterpart with 10% BG. The in vivo studies showed that the fibrous membranes as osteochondral interfaces exhibited different biological performances on superficial cartilage restoration and calcified cartilage reconstruction. All of the implanted host hyaline cartilage enabled a self-healing process and an increase in the BG content in the membranes was desirable for promoting the repair of the calcified cartilage with time. The histological staining confirmed the osteochondral interface in the 30% BG bottom membrane maintained appreciable calcified cartilage repair after 12 weeks. These findings demonstrated that such an integrated artificial osteochondral interface containing appropriate bioactive ions are potentially applicable for osteochondral interface tissue engineering.

Zinc-/copper-substituted dicalcium silicate cement: advanced biomaterials with enhanced osteogenesis and long-term antibacterial properties.

The development of bioactive Ca-silicate-based cements which may simultaneously suppress infection is promising for periapical therapy or alveolar bone defect repair. While these treatments are usually effective in the short term, many of these cements have not been designed to have an affinity with dental tissue in a prolonged anti-infectious manner and are only high alkaline in the early stages. This can lead to less favorable long-term outcomes, such as in bone repair or secondary therapy. Inspired by the strong antibacterial activity of zinc and copper ions, we developed a nonstoichiometric dicalcium silicate (C2S) substituted by 5% or 10% Zn or Cu to endow it with appropriate multifunctions. It was found that the foreign ion substitution could inhibit free CaO content and increase the pH value in the initial ∼6 h. The C2S cement only showed antibacterial activity in the early stage (6-72 h), but the C2S displayed appreciable long-term antibacterial potential against P. aeruginosa, E. faecalis and E. coli (>6 h) and S. aureus (>72 h). Moreover, the enhanced new bone regeneration by Zn substitution in C2S was confirmed in a maxillofacial bone defect model in rabbits. The increases in new bone formation adjacent to C2S-10Zn and C2S after 16 weeks of implantation were 32% and 20%, respectively. And the Tb.N values in the C2S-10Zn and C2S-10Cu groups (∼5.7 and 4.9 mm-1) were over two-fold higher than in the C2S group (∼2.0 mm-1). It is considered that Zn- or Cu-substitution in C2S is promising for applications to infectious bone repair.

Core-Shell Bioactive Ceramic Robocasting: Tuning Component Distribution Beneficial for Highly Efficient Alveolar Bone Regeneration and Repair.

Biodegradable ceramic (composite) scaffolds have inspired worldwide efforts in bone regenerative medicine. However, balancing the biodegradation with the bone's natural healing time scale remains difficult; in particularl, there is a lack of strategy to control component distribution and bioactive ion release favorable for stimulating alveolar bone tissue ingrowth in situ within an expected time window. Here we aimed to develop the robocasting core-shell bioceramic scaffolds and investigate their physicochemical properties and osteostimulative capability in beagle alveolar bone defect model. The ß-tircalcium phosphate (TCP) and 5% Mg-doped calcium silicate (CSi-Mg5) were used to fabricate the core-shell-typed TCP@TCP, CSi-Mg5@CSi-Mg5 and TCP@CSi-Mg5 porous scaffolds. Both in vitro and in vivo studies show that the CSi-Mg5 shell readily contributed to the initial mechanical strength and early-stage osteogenic activity of the TCP@CSi-Mg5 scaffolds, including tunable ion release, enhanced biodegradation, and outstanding osteogenesis capacity in comparison with the CSi-Mg5@CSi-Mg5 scaffolds and clinically available Bio-Oss granules in alveolar bone defects. Therefore, the presented core-shell robocasting of bioceramic technology and porous scaffold biomaterials enables an accurate preparation of highly bioactive and biodegradable scaffolds with a large freedom of design, and thereby may be beneficial for fabricating osteostimulation-tuned porous scaffolds for the challengeable alveolar bone defect reconstruction medicine.

Biphasic ceramic biomaterials with tunable spatiotemporal evolution for highly efficient alveolar bone repair.

Alveolar bone defects, which are characterized by a relatively narrow space and location adjacent to the cementum, require promising substitute biomaterials for their regeneration. In this study, we introduced novel yolk-shell biphasic bio-ceramic granules with/without a customized porous shell and evaluated their biological effect together with structural transformation. Firstly, a self-made coaxial bilayer capillary system was applied for the fabrication of granules. Secondly, thorough morphological and physicochemical characterizations were performed in vitro. Subsequently, the granules were implanted into critical-size alveolar bone defects (10 × 4 × 3 mm) in New Zealand white rabbits, with Bio-Oss® as the positive control. Finally, at 2, 4, 8, and 16 weeks postoperatively, the alveolar bone specimens were harvested and assessed via radiological and histological examination. Our results showed that the yolk-shell biphasic bio-ceramic granules, especially those with porous shells, exhibited a tunable ion release performance, improved biodegradation behavior and satisfactory osteogenesis compared with the homogeneously hybrid and Bio-Oss® granules both in vitro and in vivo. This study provides the first evidence that novel yolk-shell bio-ceramic granules, on account of their adjustable porous microstructure, have great potential in alveolar bone repair.

Composition control in biphasic silicate microspheres on stimulating new bone regeneration and repair of osteoporotic femoral bone defect.

Application of bioactive materials as synthetic bone graft substitutes in regenerative medicine has seen great evolution over the past decades in treating challengeable bone defects. However, balancing the preparation conditions and biological performances of inorganic biomaterials remain a great challenge, especially when there is lack of biomaterial design on how to control component distribution and how pathological bone responds to the biomaterial stimulations and osteogenesis. Here, our objective is to develop yolk-shell Ca-silicate microspheres and to investigate the potential biological performances to overcome the limitations in repair of osteoporotic bone defects. The introduction of ß-calcium silicate (CaSiO3 ) or mesoporous bioactive glass (MBG) into self-curing ß-dicalcium silicate (Ca2 SiO4 ) cement shell to form spherical granules (CaSiO3 @Ca2 SiO4 , MBG@Ca2 SiO4 ) was to retain the physicochemical property and/or microstructure of each component for optimizing bioactive ion release that could maximize osteostimulation in osteoporosis. We report a scalable shape-controlled mild fabrication protocol to yield the yolk-shell granules, endowing to different phases in yolk layer and interconnected macropore networks in the closely packed granule scaffolds. This unique heterostructure preparation is governed by coaxially aligned bilayer nozzle, inorganic powders and biocompatible binders. Extensive in vitro and in vivo evaluation showed that the CaSiO3 @Ca2 SiO4 and MBG@Ca2 SiO4 granules exhibited many superior properties such as controllable ion release, improved biodegradation and enhanced osteogenic capability in comparison with the pure Ca2 SiO4 @Ca2 SiO4 , thereby opening new mild-condition approach in fabricating osteogenesis-tailored silicate biomaterials for bone regenerative medicine, especially for efficient reconstruction of challenging pathological bone defects.

Yolk-porous shell biphasic bioceramic granules enhancing bone regeneration and repair beyond homogenous hybrid.

Bioactive stimulation and spatiotemporal evolution of porous scaffolds with time are crucial for bone regeneration rate in bone repair process. Granule-type bioceramic scaffolds have attracted significant interest in biomedical applications in recent years. However, the major limitation of such porous architecture is that the low initial porosity is disadvantageous for enhancing new bone tissue ingrowth. Here we reported that the yolk-shell-structured biphasic bioceramic granules with adjustable shell microstructures were favorable for controllable ion release in vitro, superior to the granules with the conventional homogenous hybrid structures. Also, we illustrated a significant difference in biodegradation of the granules in vivo, and especially the porous-shell granules exhibited appreciable new bone tissue ingrowth with time. The underlying fundamental mechanisms governing the new bone tissue ingrowth behavior of the yolk-shell granule scaffolds were elucidated based on microCT analyses and histological observation. It was underscored that during biodegradation in vivo, the highly bioactive ions in yolk layer were continuously released due to the porous structures of the sparingly dissolvable shell layer, thereby resulting in hollow shell and rapid new bone tissue ingrowth. Hence, these results demonstrate that the slight tailoring in microstructure and component distribution of biphasic composites is beneficial for adjusting the bone regeneration, and may help us to precisely control bone repair efficiency for a variety of clinical conditions.

Core-Shell Biphasic Microspheres with Tunable Density of Shell Micropores Providing Tailorable Bone Regeneration.

IMPACT STATEMENT: We have developed the new core-shell bioceramic CSi-Sr4@CaP-px microspheres with tuning porous shell layer so that the biodegradation of both CSi-Sr4 core and CaP shell is readily adjusted synergistically. This is for the first time, to the best of our knowledge, that the bioceramic scaffolds concerning gradient distribution and microstructure-tailoring design is available for tailoring biodegradation and ion release (bioactivity) to optimizing osteogenesis. Furthermore, it is possibly helpful to develop new bioactive scaffold system for time-dependent tailoring bioactivity and microporous structure to significantly enhance bone regeneration and repair applications, especially in some non-load-bearing arbitrary 3D anatomical bone and teeth defects.

Nonstoichiometric wollastonite bioceramic scaffolds with core-shell pore struts and adjustable mechanical and biodegradable properties.

Controllable mechanical strength and biodegradation of bioceramic scaffolds is a great challenge to treat the load-bearing bone defects. Herein a new strategy has been developed to fabricate porous bioceramic scaffolds with adjustable component distributions based on varying the core-shell-structured nozzles in three-dimensional (3D) direct ink writing platform. The porous bioceramic scaffolds composed of different nonstoichiometic calcium silicate (nCSi) with 0%, 4% or 10% of magnesium-substituting-calcium ratio (CSi, CSi-Mg4, CSi-Mg10) was fabricated. Beyond the mechanically mixed composite scaffolds, varying the different nCSi slurries through the coaxially aligned bilayer nozzle makes it easy to create core-shell bilayer bioceramic filaments and better control of the different nCSi distribution in pore strut after sintering. It was evident that the magnesium substitution in CSi contributed to the increase of compressive strength for the single-phasic scaffolds from 11.2 MPa (CSi), to 39.4 MPa (CSi-Mg4) and 80 MPa (CSi-Mg10). The nCSi distribution in pore struts in the series of core-shell-strut scaffolds could significantly adjust the strength [e.g. CSi@CSi-Mg10 (58.9 MPa) vs CSi-Mg10@CSi (30.4 MPa)] and biodegradation ratio in Tris buffer for a long time stage (6 weeks). These findings demonstrate that the nCSi components with different distributions in core or shell layer of pore struts lead to tunable strength and biodegradation inside their interconnected macropore architectures of the scaffolds. It is possibly helpful to develop new bioactive scaffolds for time-dependent tailoring mechanical and biological performances to significantly enhance bone regeneration and repair applications, especially in some load-bearing bone defects.

In vitro Chondrocyte Responses in Mg-doped Wollastonite/Hydrogel Composite Scaffolds for Osteochondral Interface Regeneration.

The zone of calcified cartilage (ZCC) is the mineralized region between the hyaline cartilage and subchondral bone and is critical in cartilage repair. A new non-stoichiometric calcium silicate (10% Ca substituted by Mg; CSi-Mg10) has been demonstrated to be highly bioactive in an osteogenic environment in vivo. This study is aimed to systematically evaluate the potential to regenerate osteochondral interface with different amount of Ca-Mg silicate in hydrogel-based scaffolds, and to compare with the scaffolds containing conventional Ca-phosphate biomaterials. Hydrogel-based porous scaffolds combined with 0-6% CSi-Mg10, 6% ß-tricalcium phosphate (ß-TCP) or 6% nanohydroxyapatite (nHAp) were made with three-dimensional (3D) printing. An increase in CSi-Mg10 content is desirable for promoting the hypertrophy and mineralization of chondrocytes, as well as cell proliferation and matrix deposition. Osteogenic and chondrogenic induction were both up-regulated in a dose-dependent manner. In comparison with the scaffolds containing 6% ß-TCP or nHAp, human deep zone chondrocytes (hDZCs) seeded on CSi-Mg10 scaffold of equivalent concentration exhibited higher mineralization. It is noteworthy that the hDZCs in the 6% CSi-Mg10 scaffolds maintained a higher expression of the calcified cartilage zone specific extracellular matrix marker and hypertrophic marker, collagen type X. Immunohistochemical and Alizarin Red staining reconfirmed these findings. The study demonstrated that hydrogel-based hybrid scaffolds containing 6% CSi-Mg10 are particularly desirable for inducing the formation of calcified cartilage.

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect.

Three-dimensional (3D) printing bioactive ceramics have demonstrated alternative approaches to bone tissue repair, but an optimized materials system for improving the recruitment of host osteogenic cells into the bone defect and enhancing targeted repair of the thin-wall craniomaxillofacial defects remains elusive. Herein we systematically evaluated the role of side-wall pore architecture in the direct-ink-writing bioceramic scaffolds on mechanical properties and osteogenic capacity in rabbit calvarial defects. The pure calcium silicate (CSi) and dilute Mg-doped CSi (CSi-Mg6) scaffolds with different layer thickness and macropore sizes were prepared by varying the layer deposition mode from single-layer printing (SLP) to double-layer printing (DLP) and then by undergoing one-, or two-step sintering. It was found that the dilute Mg doping and/or two-step sintering schedule was especially beneficial for improving the compressive strength (∼25-104 MPa) and flexural strength (∼6-18 MPa) of the Ca-silicate scaffolds. The histological analysis for the calvarial bone specimens in vivo revealed that the SLP scaffolds had a high osteoconduction at the early stage (4 weeks) but the DLP scaffolds displayed a higher osteogenic capacity for a long time stage (8-12 weeks). Although the DLP CSi scaffolds displayed somewhat higher osteogenic capacity at 8 and 12 weeks, the DLP CSi-Mg6 scaffolds with excellent fracture resistance also showed appreciable new bone tissue ingrowth. These findings demonstrate that the side-wall pore architecture in 3D printed bioceramic scaffolds is required to optimize for bone repair in calvarial bone defects, and especially the Mg doping wollastontie is promising for 3D printing thin-wall porous scaffolds for craniomaxillofacial bone defect treatment.