Suberin Fatty Acids from Outer Birch Bark: Isolation and Physical Material Characterization.

The isolation and physical material properties of suberin fatty acids (SFAs) were investigated with special reference to their potential applications as novel pharmaceutical excipients. SFAs were isolated from outer birch bark (OBB) with a new extractive hydrolysis method. The present simplified isolation process resulted in a moderate batch yield and chemical purity of SFAs, but further development is needed for establishing batch-to-batch variation. Cryogenic milling was the method of choice for the particle size reduction of SFAs powder. The cryogenically milled SFAs powder exhibited a semicrystalline structure with apparent microcrystalline domains within an amorphous fatty acids matrix. The thermogravimetric analysis (TGA) of SFAs samples showed a good thermal stability up to 200 °C, followed by a progressive weight loss, reaching a plateau at about 95% volatilization at about 470 °C. The binary blends of SFAs and microcrystalline cellulose (MCC; Avicel PH 101) in a ratio of 25:75 (w/w) displayed good powder flow and tablet compression properties. The corresponding theophylline-containing tablets showed sustained or prolonged-release characteristics. The physicochemical and bulk powder properties of SFAs isolated from OBB are auspicious in terms of potential pharmaceutical excipient applications.

Simultaneous Comparison of Two Roller Compaction Techniques and Two Particle Size Analysis Methods.

A new dry granulation technique, gas-assisted roller compaction (GARC), was compared with conventional roller compaction (CRC) by manufacturing 34 granulation batches. The process variables studied were roll pressure, roll speed, and sieve size of the conical mill. The main quality attributes measured were granule size and flow characteristics. Within granulations also the real applicability of two particle size analysis techniques, sieve analysis (SA) and fast imaging technique (Flashsizer, FS), was tested. All granules obtained were acceptable. In general, the particle size of GARC granules was slightly larger than that of CRC granules. In addition, the GARC granules had better flowability. For example, the tablet weight variation of GARC granules was close to 2%, indicating good flowing and packing characteristics. The comparison of the two particle size analysis techniques showed that SA was more accurate in determining wide and bimodal size distributions while FS showed narrower and mono-modal distributions. However, both techniques gave good estimates for mean granule sizes. Overall, SA was a time-consuming but accurate technique that provided reliable information for the entire granule size distribution. By contrast, FS oversimplified the shape of the size distribution, but nevertheless yielded acceptable estimates for mean particle size. In general, FS was two to three orders of magnitude faster than SA.

Towards improved solubility of poorly water-soluble drugs: cryogenic co-grinding of piroxicam with carrier polymers.

Amorphous solid dispersions (SDs) open up exciting opportunities in formulating poorly water-soluble active pharmaceutical ingredients (APIs). In the present study, novel catalytic pretreated softwood cellulose (CPSC) and polyvinylpyrrolidone (PVP) were investigated as carrier polymers for preparing and stabilizing cryogenic co-ground SDs of poorly water-soluble piroxicam (PRX). CPSC was isolated from pine wood (Pinus sylvestris). Raman and Fourier transform infrared (FTIR) spectroscopy, X-ray powder diffraction (XRPD) and differential scanning calorimetry (DSC) were used for characterizing the solid-state changes and drug-polymer interactions. High-resolution scanning electron microscope (SEM) was used to analyze the particle size and surface morphology of starting materials and final cryogenic co-ground SDs. In addition, the molecular aspects of drug-polymer interactions and stabilization mechanisms are presented. The results showed that the carrier polymer influenced both the degree of amorphization of PRX and stabilization against crystallization. The cryogenic co-ground SDs prepared from PVP showed an enhanced dissolution rate of PRX, while the corresponding SDs prepared from CPSC exhibited a clear sustained release behavior. In conclusion, cryogenic co-grinding provides a versatile method for preparing amorphous SDs of poorly water-soluble APIs. The solid-state stability and dissolution behavior of such co-ground SDs are to a great extent dependent on the carrier polymer used.

Fast tablet tensile strength prediction based on non-invasive analytics.

In this paper, linkages between tablet surface roughness, tablet compression forces, material properties, and the tensile strength of tablets were studied. Pure sodium halides (NaF, NaBr, NaCl, and NaI) were chosen as model substances because of their simple and similar structure. Based on the data available in the literature and our own measurements, various models were made to predict the tensile strength of the tablets. It appeared that only three parameters-surface roughness, upper punch force, and the true density of material-were needed to predict the tensile strength of a tablet. Rather surprising was that the surface roughness alone was capable in the prediction. The used new 3D imaging method (Flash sizer) was roughly a thousand times quicker in determining tablet surface roughness than traditionally used laser profilometer. Both methods gave practically analogous results. It is finally suggested that the rapid 3D imaging can be a potential in-line PAT tool to predict mechanical properties of tablets in production.

Direct compression of cellulose and lignin isolated by a new catalytic treatment.

Tablet compression of softwood cellulose and lignin prepared by a new catalytic oxidation and acid precipitation method were investigated and compared with the established pharmaceutical direct compression excipients. Catalytic pretreated softwood cellulose (CPSC) and lignin (CPSL) were isolated from pine wood (Pinus sylvestris). The compaction studies were carried out with an instrumented eccentric tablet machine. The plasticity and elasticity of the materials under compression were evaluated using force-displacement treatment and by determining characteristic plasticity (PF) and elasticity (EF) factors. With all biomaterials studied, the PF under compression decreased exponentially as the compression force increased. The compression force applied in tablet compression did not significantly affect the elasticity of CPSC and microcrystalline cellulose (MCC) while the EF values for softwood lignins increased as compression force increased. CPSL was clearly a less plastically deforming and less compactable material than the two celluloses (CPSC and MCC) and hardwood lignin. CPSL presented deformation and compaction behaviour almost identical to that of lactose monohydrate. In conclusion, the direct tablet compression behaviour of native lignins and celluloses can greatly differ from each other depending on the source and isolation method used.

3D simulation of internal tablet strength during tableting.

This study presents a new approach to model powder compression during tableting. The purpose of this study is to introduce a new discrete element simulation model for particle-particle bond formation during tablet compression. This model served as the basis for calculating tablet strength distribution during a compression cycle. Simulated results were compared with real tablets compressed from microcrystalline cellulose/theophylline pellets with various compression forces. Simulated and experimental compression forces increased similarly. Tablet-breaking forces increased with the calculated strengths obtained from the simulations. The calculated bond strength distribution inside the tablets showed features similar to those of the density and pressure distributions in the literature. However, the bond strength distributions at the center of the tablets varied considerably between individual tablets.

Rapid particle size measurement using 3D surface imaging.

The present study introduces a new three-dimensional (3D) surface image analysis technique in which white light illumination from different incident angles is used to create 3D surfaces with a photometric approach. The three-dimensional features of the surface images created are then used in the characterization of particle size distributions of granules. This surface image analysis method is compared to sieve analysis and a particle sizing method based on spatial filtering technique with nearly 30 granule batches. The aim is also to evaluate the technique in flowability screening of granular materials. Overall, the new 3D imaging approach allows a rapid analysis of large amounts of sample and gives valuable visual information on the granule surfaces in terms of surface roughness and particle shape.

Ultrasound-assisted powder-coating technique to improve content uniformity of low-dose solid dosage forms.

An ultrasound-assisted powder-coating technique was used to produce a homogeneous powder formulation of a low-dose active pharmaceutical ingredient (API). The powdered particles of microcrystalline cellulose (MCC; Avicel® PH-200) were coated with a 4% m/V aqueous solution of riboflavin sodium phosphate, producing a uniform drug layer on the particle surfaces. It was possible to regulate the amount of API in the treated powder. The thickness of the API layer on the surface of the MCC particles increased near linearly as the number of coating cycles increased, allowing a precise control of the drug content. The tablets (n = 950) prepared from the coated powder showed significantly improved weight and content uniformity in comparison with the reference tablets compressed from a physical binary powder mixture. This was due to the coated formulation remaining uniform during the entire tabletting process, whereas the physical mixture of the powders was subject to segregation. In conclusion, the ultrasound-assisted technique presented here is an effective tool for homogeneous drug coating of powders of irregular particle shape and broad particle size distribution, improving content uniformity of low-dose API in tablets, and consequently, ensuring the safe delivery of a potent active substance to patients.

Nano-coating of beta-galactosidase onto the surface of lactose by using an ultrasound-assisted technique.

We nano-coated powdered lactose particles with the enzyme beta-galactosidase using an ultrasound-assisted technique. Atomization of the enzyme solution did not change its activity. The amount of surface-attached beta-galactosidase was measured through its enzymatic reaction product D-galactose using a standardized method. A near-linear increase was obtained in the thickness of the enzyme coat as the treatment proceeded. Interestingly, lactose, which is a substrate for beta-galactosidase, did not undergo enzymatic degradation during processing and remained unchanged for at least 1 month. Stability of protein-coated lactose was due to the absence of water within the powder, as it was dry after the treatment procedure. In conclusion, we were able to attach the polypeptide to the core particles and determine precisely the coating efficiency of the surface-treated powder using a simple approach.

Development of a new method to get a reliable powder flow characteristics using only 1 to 2 g of powder.

In powder technology, it is often important to directly measure real powder flow rate from a small amount of powder. For example, in pharmaceutical industry, a frequent problem is to determine powder flow properties of new active pharmaceutical ingredient (API) in an early stage of the development when the amount of API is limited. The purpose of this paper is to introduce a new direct method to measure powder flow when the material is poorly flowing (cohesive) and the amount of material is about 1 to 2 g. The measuring system was simple, consisting of a flow chamber and electronic balance and an automated optical detection system, and for each measurement, only 1 to 2 g of sample was required. Based on the results obtained with this testing method, three selected sugar excipients, three grades of microcrystalline cellulose, and APIs (caffeine, carbamazepine, and paracetamol) can be classified as freely flowing, intermediate flowing, and poorly flowing powders, respectively. The average relative standard deviation for the flow time determinations was not more than 2-10%. The present novel flowability testing method provides a new tool for a rapid determination of flowing characteristics of powders (e.g., inhalation powders) and granules at a small scale.

Application of crustacean chitin as a co-diluent in direct compression of tablets.

A "simplex-centroid mixture design" was used to study the direct-compression properties of binary and ternary mixtures of chitin and two cellulosic direct-compression diluents. Native milled and fractioned (125-250 microm) crustacean chitin of lobster origin was blended with microcrystalline cellulose, MCC (Avicel PH 102) and spray-dried lactose-cellulose, SDLC Cellactose (composed of a spray-dried mixture of alpha-lactose monohydrate 75% and cellulose powder 25%). An instrumented single-punch tablet machine was used for tablet compactions. The flowability of the powder mixtures composed of a high percentage of chitin and SDLC was clearly improved. The fractioned pure chitin powder was easily compressed into tablets by using a magnesium stearate level of 0.1% (w/w) but, as the die lubricant level was 0.5% (w/w), the tablet strength collapsed dramatically. The tablets compressed from the binary mixtures of MCC and SDLC exhibited elevated mechanical strengths (>100 N) independent of the die lubricant level applied. In conclusion, fractioned chitin of crustacean origin can be used as an abundant direct-compression co-diluent with the established cellulosic excipients to modify the mechanical strength and, consequently, the disintegration of the tablets. Chitin of crustacean origin, however, is a lubrication-sensitive material, and this should be taken into account in formulating direct-compression tablets of it.

Image-based characterization of powder flow to predict the success of pharmaceutical minitablet manufacturing.

Powder flowability plays an important role in die filling during tablet manufacturing. The present study introduces a novel small-scale measuring technique for powder flow. Based on image analysis, the flow was defined depending on the variation of luminous intensity and the movement of powder inside the measurement cuvette. Using quantities around 100 mg it was possible to characterize a wide range of common pharmaceutical powders, especially in distinguishing subtle differences in flow caused by minor changes in samples characteristics. The method was compared with powder rheometry, which is widely used in the pharmaceutical literature, and showed a significant improvement in predicting the success of pharmaceutical minitablet manufacture (d = 5 mm). Tablet weight variation (RSD) was defined as the most efficient way to assess relevant powder flow behaviour in tablet production when using the novel device. The proposed method was distinguished from others by its ability to classify different grades of microcrystalline cellulose in the die-filling process. Subsequently, eight common pharmaceutical powders, both excipients and APIs, were properly ranked as a function of flowability based on their physical properties. The method showed a high repeatability, with a relative standard deviation not more than 10%.

Sugar end-capped poly-D,L-lactides as excipients in oral sustained release tablets.

Sugar end-capped poly-D,L-lactide (SPDLA) polymers were investigated as a potential release controlling excipient in oral sustained release matrix tablets. The SPDLA polymers were obtained by a catalytic ring-opening polymerization technique using methyl alpha-D-gluco-pyranoside as a multifunctional initiator in the polymerization. Polymers of different molecular weights were synthesized by varying molar ratios of monomer/catalyst. The matrix tablets were prepared by direct compression technique from the binary mixtures of SPDLA and microcrystalline cellulose, and theophylline was used as a model drug. The tablet matrices showed in vitro reproducible drug release profiles with a zero-order or diffusion-based kinetic depending on the SPDLA polymer grade used. Further release from the tablet matrices was dependent on the molecular weight of the SPDLA polymer applied. The drug release was the fastest with the lowest molecular weight SPDLA grade, and the drug release followed zero-order rate. With the higher molecular weight SPDLAs, more prolonged dissolution profiles for the matrix tablets (up to 8-10 h) were obtained. Furthermore, the prolonged drug release was independent of the pH of the dissolution media. In conclusion, SPDLAs are a novel type of drug carrier polymers applicable in oral controlled drug delivery systems.

Crystal morphology engineering of pharmaceutical solids: tabletting performance enhancement.

Crystal morphology engineering of a macrolide antibiotic, erythromycin A dihydrate, was investigated as a tool for tailoring tabletting performance of pharmaceutical solids. Crystal habit modification was induced by using a common pharmaceutical excipient, hydroxypropyl cellulose, as an additive during crystallization from solution. Observed morphology of the crystals was compared with the predicted Bravais-Friedel-Donnay-Harker morphology. An analysis of the molecular arrangements along the three dominant crystal faces [(002), (011), and (101)] was carried out using molecular simulation and thus the nature of the host-additive interactions was deduced. The crystals with modified habit showed improved compaction properties as compared with those of unmodified crystals. Overall, the results of this study proved that crystal morphology engineering is a valuable tool for enhancing tabletting properties of active pharmaceutical ingredients and thus of utmost practical value.

Predicting tablet tensile strength with a model derived from the gravitation-based high-velocity compaction analysis data.

In the present study, a model was developed to estimate tablet tensile strength utilizing the gravitation-based high-velocity (G-HVC) method introduced earlier. Three different formulations consisting of microcrystalline cellulose (MCC), dicalcium phosphate dihydrate (DCP), hydroxypropyl methylcellulose (HPMC), theophylline and magnesium stearate were prepared. The formulations were granulated using fluid bed granulation and the granules were compacted with the G-HVC method and an eccentric tableting machine. Compaction energy values defined from G-HVC data predicted tensile strength of the tablets surprisingly well. It was also shown, that fluid bed granulation improved the compaction energy intake of the granules in comparison to respective physical mixtures. In addition, general mechanical properties and elastic recovery were also examined for all samples. In this study it was finally concluded, that the data obtained by the method was of practical relevance in pharmaceutical formulation development.

Direct compression properties of chitin and chitosan.

Deformation and compaction properties of native amino poly-saccharides chitin and chitosan were studied and compared with those obtained with established pharmaceutical direct compression excipients. An instrumented single-punch tablet machine was used for tablet compaction. The following compression parameters were evaluated: a ratio of crushing strength and compression pressure, plasticity and elasticity factor (PF and EF), tensile strength and R-value. Chitin and chitosan were found to have a marked tendency to plastic deformation, and both showed a good compression behaviour compared with the other direct compression excipients including microcrystalline cellulose. It is concluded that chitin and chitosan are potential co-excipients for direct compression applications.

Controlling granule size by granulation liquid feed pulsing.

The effects of inlet air humidity, granulation liquid feed rate and granulation liquid feed pulsing on the particle-size distribution of final granules were studied in a laboratory scale fluid-bed granulator using a central composite study design. The factors examined were modelled using three different particle-size measurement techniques (sieve analysis, laser light diffraction and the spatial filtering technique). Best goodness of fit (R2=0.94) and goodness of prediction (Q2=0.90) values were obtained using particle-size results of the spatial filtering technique. Increasing inlet air humidity and granulation liquid feed rate resulted in greater median granule size, as expected. When pulsing (interruption of granulation liquid feed in predetermined sequences) was used, the median granule size decreased clearly. This effect was strong, especially with high inlet air humidity and rapid liquid feed rate processes. Granulation liquid feed pulsing is an effective way to modify the particle size of final granules. Pulsing can be used as a controlling tool to compensate for excessive moisture content in the granulation process.

Effect of fluidisation activity on end-point detection of a fluid bed drying process.

The influence of inlet air humidity variations on fluid bed drying end-point detection was the primary focus here. Various drying end-point criteria based on temperature and humidity measurements were compared. Seasonally changing inlet air humidity affects the moisture content of the finished granules, as long as the drying process remains unchanged. However, a specific moisture content of the finished granules is commonly desired after fluid bed drying. When experimental batches of varying inlet air humidity were compared at the beginning of the drying phase, the temperature of the granules increased linearly as the humidity of the inlet air increased. This effect causes variation in moisture contents of the final granules of different batches when the fixed temperature of the mass is used as an end-point criterion. With varying inlet air humidity, the often used DeltaT temperature difference method resulted in more precise estimation of the drying end-point than the constant temperature criterion. In this study new insights were found into the correlation between moisture content and temperature of the fluidising mass. Fluidisation activity greatly affected detection of drying end-point. Use of the DeltaT criterion requires proper fluidisation throughout the process.

3D printed UV light cured polydimethylsiloxane devices for drug delivery.

The goal of this work was to study the printability of PDMS with a semi-solid extrusion printer in combination with the UV-assisted crosslinking technology using UV-LED light to manufacture drug containing structures. Structures with different pore sizes and different drug loadings were prepared containing prednisolone as a model drug. The work showed that it was possible to print drug-free and drug-loaded drug delivery devices of PDMS with the 3D printing technique used in this study. The required UV-curing time to get sufficient crosslinking yield and mechanical strength was minimum three minutes. The microgram drug release from the printed structures was highest for the most drug loaded structures regardless of the porosity of the devices. By altering the surface area/volume ratio it was possible to print structures with differences in the release rate. This study shows that room-temperature semi-solid extrusion printing 3D printing technique in combination with UV-LED crosslinking is an applicable method in the production of prednisolone containing PDMS devices. Both the extrusion 3D printing and the UV-crosslinking was done at room temperature, which make this manufacturing method an interesting alternative for manufacturing controlled release devices containing temperature susceptible drugs.

Interdependence of particle properties and bulk powder behavior of indomethacin in quench-cooled molten two-phase solid dispersions.

Solid dispersions (SDs) hold a proven potential in formulating poorly water-soluble drugs. The present paper investigates the interfacial phenomena associated with the bulk powder flow, water sorption, wetting and dissolution of the SDs prepared by a modified melt and quench-cooling (QC) method. Poorly water-soluble indomethacin (IND) was QC molten with solubilizing graft copolymer (Soluplus®) or polyol sugar alcohol (xylitol, XYL). The interfacial interactions of SDs with air/water were found to be reliant on the type (amorphous/crystalline) and amount of the carrier material used. The final SDs were composed of fused agglomerates (SOL) or large jagged particles (XYL) with good wetting and powder flow properties. The initial dissolution of IND was accelerated by both carrier materials studied. The QC molten SDs with amorphous Soluplus® significantly improved the dissolution rate of IND at pH 6.8 (79.9 ±â€¯0.2% at 30 min) compared to that of pure crystalline drug. The substantial improvement in the dissolution rate of IND was in connection with the amorphous state of the drug being stabilized by Soluplus® in the QC molten SDs. However, it is evident that a strong H-bond formation between the components in some regions of the QC molten SDs can limit the dissolution of IND. The QC molten two-phase SDs with a polyol carrier (XYL) showed rapid and continuous drug release without reaching a plateau.