Ultrasonic, bipolar, and integrated energy devices: comparing heat spread in collateral tissues.

BACKGROUND: Integrated devices incorporating ultrasonic and bipolar technology have been used in laparoscopic surgery, however, are not yet incorporated into open operations. Here, we compare thermal spread and recurrent laryngeal nerve (RLN) functional data of the integrated THUNDERBEAT Open Fine Jaw device, the bipolar Ligasure Small Jaw, and the ultrasonic Harmonic Focus for open thyroidectomy. MATERIALS AND METHODS: The three energy devices were compared in a live porcine model using three tissue types including liver, muscle, and thyroid. The devices were fired three times on each energy setting, and the thermal spread was measured by thermocouples that were inserted in surrounding tissues at 1-mm intervals. To determine RLN injury, devices were fired at successive 1-mm increments from the RLN until the monitor signal was lost. RESULTS: When comparing heat generated across these devices at 1 mm, the peak temperature (Celsius) reached in liver tissue was observed with the ultrasonic device (115.4 ± 86.7), in muscle tissue with the integrated device (104.2 ± 82.1), and in thyroid with the bipolar device (81.4 ± 41.3). Temperatures generated at individual settings on each device were similar (P = 0.11-0.81). RLN injury occurred after firing on manually approximated tissue 1-mm away from the RLN for all devices; however, there was no signal loss at ≥2 mm. CONCLUSIONS: Heat transfer was similar among all devices with the exception of the ultrasonic device when used in the liver, which showed higher temperatures. Liver tissue showed the most consistent results. RLN injury did not occur if the devices were fired on manually approximated tissue ≥2 mm from the nerve.

Healing at implant sites prepared conventionally or by means of Sonosurgery ®. An experimental study in dogs.

OBJECTIVE: To compare peri-implant tissue healing at implants installed in sites prepared with conventional drills or a sonic device. MATERIAL AND METHODS: In six Beagle dogs, the mandibular premolars and first molars were extracted bilaterally. After 3 months, full-thickness muco-periosteal flaps were elevated and recipient sites were prepared in both sides of the mandible. In the right side (control), the osteotomies were prepared using conventional drills, while, at the left side (test), a sonic device (Sonosurgery(®)) was used. Two implants were installed in each side of the mandible. After 8 weeks of non-submerged healing, biopsies were harvested and ground sections prepared for histological evaluation. RESULTS: The time consumed for the osteotomies at the test was more than double compared to the conventional control sites. No statistically significant differences were found for any of the histological variables evaluated for hard and soft tissue dimensions. Although not statistically significant, slightly higher mineralized bone-to-implant contact was found at the test (65.4%) compared to the control (58.1) sites. CONCLUSIONS: Similar healing characteristics in osseointegration and marginal hard tissue remodeling resulted at implants installed into osteotomies prepared with conventional drills or with the sonic instrument (Sonosurgery(®)).

Three-dimensional computed tomographic evaluation of bilateral sagittal split osteotomy lingual fracture line and le fort I pterygomaxillary separation in orthognathic surgery using cadaver heads: ultrasonic osteotome versus conventional saw.

PURPOSE: The purpose of this study was to observe the quality of the fracture line on the lingual side of the mandible after sagittal split osteotomy and the quality of pterygomaxillary separation after Le Fort I osteotomy using the BoneScalpel ultrasonic osteotome. MATERIALS AND METHODS: Bimaxillary procedures, according to the standard protocol, were performed using 10 fresh cadaver heads. The ultrasonic osteotome was used in the study group, and a reciprocating saw was used in the control group. Three-dimensional reconstructions of postoperative computed tomographic scans were obtained. The lingual ramus fracture pattern and the pterygomaxillary separation pattern were observed, classified, and compared. Postoperative dissections of the skulls were performed to assess the integrity of the infra-alveolar nerve and the descending palatine artery. RESULTS: No significant differences were found in the cutting time of bone between the BoneScalpel and the sagittal saw. Of the sagittal split osteotomies in the study group, 90% showed a good pattern (vertical pattern of fracture line extending to the inferior border of the mandible running behind the mandibular canal) compared with 50% of the sagittal split osteotomies in the control group. Ideal separation of the pterygoid plates without fractures was observed in 80% of the Le Fort I osteotomies in the study group compared with 50% of the osteotomies in the control group. High-level fractures occurred in 30% of cases in the control group compared with none in the study group. The integrities of the infra-alveolar nerve and the descending palatine artery were preserved in all cases. CONCLUSION: Use of the ultrasonic BoneScalpel did not require more time than the conventional method. An improved pattern of lingual fracture lines in mandibular sagittal split osteotomy procedures and the pattern of pterygomaxillary separation in Le Fort I osteotomy procedures were observed.

Mandibular condylectomy revisited: technical notes concerning the use of an ultrasonic system.

Condylar hyperplasia is a well-known pathologic entity with an established treatment protocol. Traditionally, saws and drills have been used in the condylar osteotomy. The use of ultrasonic systems has optimized many procedures in the maxillofacial area; however, exploration of the use of this technique for condylectomy has been limited. Ultrasonic systems offer several advantages, such as a decrease in the risk of blood vessel damage and clarity of the osteotomy. The present report addressed the scope of condylar osteotomy using ultrasonic systems.

Ultrasonic versus drills implant site preparation: a histologic analysis in bovine ribs.

PURPOSE: Ultrasonic surgery is a recently developed system for cutting bone with microvibrations. The aim of the current study was a histologic comparison between conventional drills versus ultrasonic surgery devices in implant bed preparation. METHODS: Ten bovine ribs were used, and a total of 100 perforations were randomly performed: half (n = 50) (group A) of the perforations were done through conventional drills using a single cylindrical bur (Bone System, Milan, Italy), 13 mm in height and 2 mm in width at a speed of 400 rpm, and the other half (n = 50) (group B) using an ultrasonic device (Surgysonic; Esacrom, Imola Italy), mounted with a diamond-coated cylindrical tip. After implant sites' preparation, the ribs were immediately stored in 10% buffered formalin and processed to obtain thin ground sections. RESULTS: At higher magnification, microcracks at the interface were detected. In group A, they were numerous and showed a thickness and depth ranging from 20 to 120 µm and from 500 to 1000 µm, respectively. In group B, very few or no microcracks were present. Statistically significant differences were found in the microcracks density in the cortical bone but not in the cancellous bone. CONCLUSIONS: The findings from this study suggest that ultrasonic implant site preparation showed a higher performance in terms of accuracy and uniformity of the osteotomy cut, compared with conventional rotary instruments. Further studies should be conducted to understand whether a smooth, congruent implant bed able to retain fine bone structures may affect the early phases of bone healing and therefore improve osseointegration.

Utility of the ultrasonic scalpel in mandibular distraction osteogenesis.

The purpose of this study was to describe our technique of bilateral mandibular distraction for micrognathia and to highlight the ultrasonic scalpel as an alternative to conventional saws in performing osteotomies for mandibular distraction osteogenesis. To do so, we retrospectively reviewed all patients who underwent mandibular distraction with an ultrasonic scalpel for tongue-based upper airway obstruction due to micrognathia between 2010 and 2011. Study outcome measures include operative blood loss, length of surgery, postoperative complications, and avoidance of a tracheostomy. Excel (Microsoft) was used to calculate averages, P values (2-tailed Student t test), and SDs for operative data, sleep studies, and cephalometric analysis. Nine patients--7 females and 2 males--were distracted for a mean distance of 17 ± 6 mm. Mean blood loss was 15 ± 7 mL, and the average length of surgery was 111 ± 27 minutes. One patient returned to the operating room for debridement/washout of a wound infection, but distraction was continued without sequelae. There were no other postoperative complications. Resolution of airway obstruction was evidenced by clinical examination and avoidance of a tracheostomy in all cases. Based on these data, we feel that mandibular distraction with univector, internal distractors, and ultrasonic osteotomies at the mandibular angle is safe and efficacious at relieving tongue-based upper airway obstruction and avoiding a tracheostomy.

Sonosurgery for atraumatic tooth extraction: a clinical report.

The preservation of an intact labial plate during tooth extraction is a critical determinant of whether an immediate implant can be placed and is also an important predictor of the esthetic result. The purpose of this clinical report was to present a method for atraumatic tooth extraction by using an air-driven sonic instrument with specially designed inserts. This surgical technique provides the clinician with an efficient method for atraumatic tooth extraction and preservation of an intact labial plate.

Pulp hyperthermia during tooth preparation: the effect of rotary--instruments, lasers, ultrasonic devices, and airborne particle abrasion.

The rise in pulp temperature during restorative therapy can compromise vitality of the dental pulp. Of the various reasons for the increase in intrapulpal temperature, tooth preparation is considered to be the primary cause. This article describes the reasons for the rise in pulp temperature during various modalities of tooth preparation. The article also comments on the measures that need to be taken to avoid the risk of pulp hyperthermia during tooth preparation.

Maxillary sinus augmentation with a sonic handpiece for the osteotomy of the lateral window: a clinical report.

Several techniques have been proposed to manage patients with insufficient bone height for implant placement in the posterior maxilla. The lateral approach to sinus elevation is a successful procedure, with percentages of success close to 100%. Unfortunately, a frequent complication encountered during sinus elevation procedure is perforation of the Schneiderian membrane. In this clinical report, the authors present the application of a diamond coated sonic tip and an air-driven sonic instrument, commonly used in prosthodontics for the preparation of the lateral window osteotomy during sinus augmentation procedures.

Harmonic scalpel for a bloodless partial glossectomy: a case report.

Tongue surgery is almost always complicated by intraoperative bleeding. Its rich blood supply especially from the lingual vessels makes the operative field bloody. Electrocautery has been widely used to replace cold scissors in order to achieve better hemostasis. The use of ultrasonic harmonic scalpel for glossectomy is still new in this country. We report a case of partial glossectomy using the harmonic scalpel in a patient who had a squamous cell carcinoma of the lateral border of the tongue.

Advances in Endovascular Intervention Using Biomaterials: Study on Heat Efficiency of Scissor-Type Ultrasonic Catheter Device.

To improve the performance of the ultrasonic device during the endovascular operation, a scissor-type ultrasonic catheter device with compound vibration was developed. The heat generated by friction between the target and the device affects its coagulation mechanism while the actuator contacts the tissue. The scissor-type ultrasonic catheter device proposed in this study is expected to improve heat generation performance because it has the action of rubbing the object when it is pushed by combined vibration. In addition, since it is constructed by simple notch processing, it can be miniaturized and can be expected to be introduced into catheters. However, the observation of ultrasonic vibration during frictional heating is difficult, which is an issue for device design. In this paper, a thermal-structure coupling analysis was done using the finite element method to calculate the heat generation efficiency and evaluate its coagulation performance.

A comparative study of the incidence of Schneiderian membrane perforations during maxillary sinus augmentation with a sonic oscillating handpiece versus a conventional turbine handpiece.

BACKGROUND: Sonic instruments may reduce perforation rates of the schneiderian membrane during lateral window sinus augmentation procedures. This study compares the incidence of membrane perforations using a sonic handpiece with an oscillating diamond insert versus a turbine handpiece with a conventional rotary diamond stone during lateral window sinus augmentation procedures. MATERIALS AND METHODS: A retrospective chart analysis identified all lateral window sinus augmentation procedures done during a defined period. Among these procedures, those performed with a sonic handpiece and an oscillating diamond insert (experimental) and those performed with a conventional turbine and rotary diamond stone (conventional) were selected for this study. Reported occurrences of sinus membrane perforations during preparation of the osteotomy and elevation of the sinus membrane, as well as postoperative complications, were recorded and compared between treatment groups. RESULTS: Ninety-three consecutive patients were identified for a total of 130 sinus augmentation procedures (51 conventional, 79 experimental). Schneiderian membrane perforations were noted during preparation of the lateral window osteotomy in 27.5% of the sinuses in the conventional group and 12.7% of sinuses in the experimental group. During membrane elevation, perforations were noted in 43.1% of the sinuses in the conventional group and 25.3% of sinuses in the experimental group. Both differences in perforation rates were statistically significant (p < .05). There was no statistically significant difference in postoperative complications. CONCLUSIONS: In this study, the use of a sonic instrument to prepare the lateral window osteotomy during sinus elevation procedures resulted in a reduced perforation rate of the Schneiderian membrane compared with the conventional turbine instrument.

A Prospective, Randomized Study between the Small Jaw® and the Harmonic Focus® in Open Thyroidectomy.

OBJECTIVES: LigaSure Small Jaw(®) (LSJ) was recently developed and applied to thyroid surgery along with Harmonic Focus(®) (HF). We compared the 2 devices in open total thyroidectomy for papillary thyroid carcinoma (PTC). STUDY DESIGN: A prospective, randomized study. SETTING: Tertiary care center. METHODS: This prospective, randomized study included 126 patients enrolled between December 2011 and June 2012. The numbers of patients in the LSJ group and the HF group were 64 and 62, respectively. Operative times, drain output, parathyroid status, complications, laboratory data, hospital stay, and analgesia requirements were analyzed. RESULTS: Operation time, parathyroid status, postoperative complications including hypocalcemia, oral calcium supplement, calcium, parathyroid hormone, usage count of painkiller, and hospital stay were not different among the 2 groups. Ionized calcium on postoperative days 1, 2, and 10 was higher in the LSJ group (P = .04, P = .04, P = .01), and drain output was lower in the LSJ group (106.8 vs 123.6 mL, P = .01). CONCLUSIONS: Open thyroidectomy for PTC using the HF or the LSJ was safe and effective and was not associated with any increase in complications. Surgical outcomes and operative morbidity were equivalent between the 2 groups.

Use of a new retrograde filling material (Biodentine) for endodontic surgery: two case reports.

Mineral trioxide aggregate (MTA) is considered at the present time as the gold standard for root-end filling in endodontic surgery. However, this biocompatible material presents several drawbacks such as a long setting time and handling difficulties. The aim of this article is to present a new commercialized calcium silicate-based material named Biodentine with physical improved properties compared to MTA in a clinical application. Two endodontic microsurgeries were performed by using specific armamentarium (microsurgical instrumentation, ultrasonic tips) under high-power magnification with an operatory microscope. Biodentine was used as a root-end filling in order to seal the root canal system. The two cases were considered completely healed at 1 year and were followed for one more year. The 2-year follow-up consolidated the previous observation with absence of clinical symptoms and radiographic evidence of regeneration of the periapical tissues.

Minimal intervention dentistry II: part 4. Minimal intervention techniques of preparation and adhesive restorations. The contribution of the sono-abrasive techniques.

The concept of minimal intervention in oral medicine is based on advances in biological sciences applied to the dental organ. Many cultural barriers, economic as well as technical, have thwarted the application of micro-invasive conservative techniques by the general practitioner. Emerging technologies do not remove all obstacles but promote the integration of less invasive techniques in daily practice. Sono-abrasion is a technique for the selective preparation of enamel and dentine offering excellent efficacy, quality and safety. The authors describe the therapeutic principles, the choice of instrumentation and its mode of action and discuss its interest in adhesive restorative dentistry. The illustrated clinical situations focus on the preservation and optimisation of tissue bonding for both initial lesions and advanced lesions.

Endoscopy-assisted transoral resection of large benign parapharyngeal space tumors.

We have evaluated the outcomes of endoscopically-assisted resection of large benign tumours of the parapharyngeal space by an intraoral approach. Six patients with primary benign tumours were treated in this way. The lesions were pleomorphic adenomas, Warthin's tumour, and schwannoma. The sizes of the tumours varied from 4×4 cm to 7×7 cm. All tumours were removed completely without rupture and without damage to the facial nerve. No patient developed any permanent postoperative complications such as damage to the facial nerve, salivary fistula, or limited mouth opening. The cosmetic effects were excellent. The patients were followed up for 8 to 21 months without recurrence. Endoscopically-assisted transoral resection of large benign tumours of the parapharyngeal space is a simple and safe technique that achieves excellent aesthetic and functional results.

Ultracision Harmonic Scalpel in oral and oropharyngeal cancer resection.

OBJECTIVE: The aim of this prospective study was to evaluate the benefits and risks when using an Ultracision Harmonic Scalpel in the surgical treatment of oral and oropharyngeal carcinomas. STUDY DESIGN: Prospective non-randomized. SETTING: Clinica Otorinolaringoiatrica, Azienda Ospedaliero-Universitaria. Trieste, Italy. SUBJECTS AND METHODS: In this study, conducted from April 2008 to August 2010, 36 consecutive patients underwent resection of oral or oropharyngeal carcinoma and lateral lymphadenectomy using the Ultracision Harmonic Scalpel. Evaluation criteria included length of the surgical procedure, intraoperative blood loss, quantity of neck drainage on the first, second and third postoperative days, postoperative complications, and a subjective assessment of postoperative pain and lymphatic oedema of the neck. Results were compared with previous surgical procedures carried out between May 2006 and March 2008 using cold knife and bipolar haemostasis (n = 36) when the Harmonic Scalpel was not available. RESULTS: In patients treated with the Harmonic Scalpel, operating time was significantly reduced, both for resection of the carcinoma and the lateral lymphadenectomy. Intraoperative blood loss and neck drainage on the first and second postoperative days were significantly less and pain scores were significantly lower than in the cold knife group. No postoperative complications were noted in the Harmonic Scalpel group. The only disadvantage noted in the Harmonic Scalpel group was the high incidence of lymphatic oedema of the neck. CONCLUSIONS: Use of the Harmonic Scalpel during resection of oral cancer and lateral lymphadenectomy is safe and confers some advantages over conventional methods.

A comparison of dentin cutting efficiency of 4 round-tipped ultrasonic instruments.

INTRODUCTION: Ultrasonic instruments are available for a variety of endodontic uses. Few published evaluations exist that compare the dentin cutting efficiency of endodontic ultrasonic tips. Furthermore, previous comparison studies often did not take into account 2 critical factors: clinically relevant downward forces and linear movement during use. METHODS: Four different round-tipped ultrasonic tips were compared (n = 5 per tip group): BUC-1 (Obtura Spartan, Fenton, MO), BL-2 (B&L Biotech, Bala Cynwyd, PA), BL-3 (B&L Biotech), and START-X #2 (Dentsply Maillefer, Ballaigues, Switzerland). The tips were attached to a testing apparatus that applied a 15-g axial force and a linear movement during instrumentation of a human dentin specimen. Instrumentation was completed at the manufacturers' recommended power settings, and 3 of the tips were also compared at an equal power setting. Instrumentation consisted of 20-second cycles for a total of 6 minutes. Dentin specimens were weighed at baseline and after 2, 4, and 6 minutes of instrumentation. The dentin cutting efficiency was measured by the change in weight of dentin specimens to the nearest 0.1 mg. RESULTS: A 1-factor analysis of variance and Tukey post hoc analysis of cumulative dentin removal (after 6 minutes of instrumentation) revealed a statistically significant difference among the 4 ultrasonic tips (P ≤ .0001) at the recommended PS, with the BUC-1 tip removing significantly more dentin across time. At an equal power setting, the BUC-1 was significantly more efficient than the BL-3; no difference was found between the BUC-1 and the BL-2. CONCLUSIONS: Within the limits of this study, the BUC-1 showed the greatest dentin removal. Adding a linear movement and a clinically relevant axial force allows better generalization to clinical applications.

Analysis of forces in conventional and ultrasonically assisted plane cutting of cortical bone.

Bone cutting is a well accepted but technically demanding surgical procedure in orthopaedics. A level of tool penetration force during cutting of bones has been the prime concern to surgeons, since it can produce unnecessary mechanical damage to surrounding tissues. Research in this area has been undertaken for many decades to find ways to minimise the cutting force. Cutting of bone with ultrasonic tools is a relatively new technique replacing conventional procedures in neuro-, dental and orthopaedic surgeries, due to its precision and safety. In this article, the level of forces produced during a chisel-like tool penetration in a fresh cortical bone is studied. The obtained force data are analysed for both conventional cutting and ultrasonically assisted cutting. Through a series of experiments, it was demonstrated that the depth of cut and parameters of ultrasonic oscillations affected the level of cutting force, the former being the main factor in both types of cutting. It was found that the tool penetration force was decreased with an increase in the ultrasonic frequency or amplitude and was not affected by the cutting speed. The rise in bone temperature was measured and was found to be insensitive to the level of cutting speed within the range used in this study.

Evaluation of root-end preparation with a new ultrasonic tip.

INTRODUCTION: This study was conducted to evaluate the effect of a new ultrasonic tip (Jetip) for root-end preparation. METHODS: A total of 80 single-rooted teeth were endodontically treated, and the apical 3 mm of the root apex was resected. Teeth were randomly distributed into 2 experimental groups according to the ultrasonic tips used to prepare the root-end cavity. Epoxy resin replicas of root-end surfaces after root-end resection were obtained. A root-end cavity was then prepared with an ultrasonic tip, either Jetip or AS3D. Replicas of the apices were fabricated after the retropreparations, and they were processed for analysis by scanning electron microscopy (SEM) to evaluate the presence of microcracks and the quality of the root-end preparation. The morphologic characteristics of the ultrasonic tip were also assessed by SEM. The time required for root-end preparation was recorded. RESULTS: There were no statistically significant differences between the Jetip and AS3D groups in the mean time for the root-end preparation, the incidence of microcracks, or the quality of the root-end preparation (P > .05). SEM analysis showed that Jetip exhibited smoothed microprojections after the root preparations, whereas the loss of diamond particles was observed in AS3D. CONCLUSIONS: Both Jetip and AS3D provided rapid and regular root-end preparations. The cutting efficiencies of both Jetip and AS3D decreased with the number of times the tips were used. The Jetip showed smooth microprojections after root-end preparation, whereas the AS3D tip exhibited the loss of diamond particles.