Biological matrix composites from cultured plant cells.

We present an approach to fabricate biological matrix composites made entirely from cultured plant cells. We utilize the cell's innate ability to synthesize nanofibrillar cell walls, which serve as the composite's fundamental building blocks. Following a controlled compression/dehydration process, the cells arrange into lamellar structures with hierarchical features. We demonstrate that the native cell wall nanofibrils tether adjacent cells together through fibrillar interlocking and intermolecular hydrogen bonding. These interactions facilitate intercellular adhesion and eliminate the need for other binders. Our fabrication process utilizes the entire plant cell, grown in an in vitro culture; requires no harsh chemical treatments or waste-generating extraction or selection processes; and leads to bulk biocomposites that can be produced in situ and biodegrade in soil. The final mechanical properties are comparable to commodity plastics and can be further modulated by introducing filler particles.

Novel Bioplastic Based on PVA Functionalized with Anthocyanins: Synthesis, Biochemical Properties and Food Applications.

Over the last ten years, researchers' efforts have aimed to replace the classic linear economy model with the circular economy model, favoring green chemical and industrial processes. From this point of view, biologically active molecules, coming from plants, flowers and biomass, are gaining considerable value. In this study, firstly we focus on the development of a green protocol to obtain the purification of anthocyanins from the flower of Callistemon citrinus, based on simulation and on response surface optimization methodology. After that, we utilize them to manufacture and add new properties to bioplastics belonging to class 3, based on modified polyvinyl alcohol (PVA) with increasing amounts from 0.10 to 1.00%. The new polymers are analyzed to monitor morphological changes, optical properties, mechanical properties and antioxidant and antimicrobial activities. Fourier transform infrared spectroscopy (FTIR) spectra of the new materials show the characteristic bands of the PVA alone and a modification of the band at around 1138 cm-1 and 1083 cm-1, showing an influence of the anthocyanins' addition on the sequence with crystalline and amorphous structures of the starting materials, as also shown by the results of the mechanical tests. These last showed an increase in thickening (from 29.92 µm to approx. 37 µm) and hydrophobicity with the concomitant increase in the added anthocyanins (change in wettability with water from 14° to 31°), decreasing the poor water/moisture resistance of PVA that decreases its strength and limits its application in food packaging, which makes the new materials ideal candidates for biodegradable packaging to extend the shelf-life of food. The functionalization also determines an increase in the opacity, from 2.46 to 3.42 T%/mm, the acquisition of antioxidant activity against 2,2-diphenyl-1-picrylhdrazyl and 2,2'-azino-bis-(3-ethylbenzothiazoline-6-sulfonic acid) radicals and, in the ferric reducing power assay, the antimicrobial (bactericidal) activity against different Staphylococcus aureus strains at the maximum tested concentration (1.00% of anthocyanins). On the whole, functionalization with anthocyanins results in the acquisition of new properties, making it suitable for food packaging purposes, as highlighted by a food fresh-keeping test.

Highly Efficient Modular Construction of Functional Drug Delivery Platform Based on Amphiphilic Biodegradable Polymers via Click Chemistry.

Amphiphilic copolymers with pendant functional groups in polyester segments are widely used in nanomedicine. These enriched functionalities are designed to form covalent conjugates with payloads or provide additional stabilization effects for encapsulated drugs. A general method is successfully developed for the efficient preparation of functional biodegradable PEG-polyester copolymers via click chemistry. Firstly, in the presence of mPEG as initiator, Sn(Oct)2-catalyzed ring-opening polymerization of the α-alkynyl functionalized lactone with D,L-lactide or ε-caprolactone afforded linear mPEG-polyesters bearing multiple pendant alkynyl groups. Kinetic studies indicated the formation of random copolymers. Through copper-catalyzed azide-alkyne cycloaddition reaction, various small azido molecules with different functionalities to polyester segments are efficiently grafted. The molecular weights, polydispersities and grafting efficiencies of azido molecules of these copolymers were investigated by NMR and GPC. Secondly, it is demonstrated that the resulting amphiphilic functional copolymers with low CMC values could self-assemble to form nanoparticles in aqueous media. In addition, the in vitro degradation study and cytotoxicity assays indicated the excellent biodegradability and low cytotoxicity of these copolymers. This work provides a general approach toward the preparation of functional PEG-polyester copolymers in a quite efficient way, which may further facilitate the application of functional PEG-polyesters as drug delivery materials.

Improved Synthesis of a Novel Biodegradable Tunable Micellar Polymer Based on Partially Hydrogenated Poly(ß-malic Acid-co-benzyl Malate).

Poly(benzyl malate) (PBM), together with its derivatives, have been studied as nanocarriers for biomedical applications due to their superior biocompatibility and biodegradability. The acquisition of PBM is primarily from chemical routes, which could offer polymer-controlled molecular weight and a unique controllable morphology. Nowadays, the frequently used synthesis from L-aspartic acid gives an overall yield of 4.5%. In this work, a novel synthesis route with malic acid as the initiator was successfully designed and optimized, increasing the reaction yield up to 31.2%. Furthermore, a crystalline form of PBM (PBM-2) that polymerized from high optical purity benzyl-ß-malolactonate (MLABn) was discovered during the optimization process. X-ray diffraction (XRD) patterns revealed that the crystalline PBM-2 had obvious diffraction peaks, demonstrating that its internal atoms were arranged in a more orderly manner and were different from the amorphous PBM-1 prepared from the racemic MLABn. The differential scanning calorimetry (DSC) curves and thermogravimetric curves elucidated the diverse thermal behaviors between PBM-1 and PBM-2. The degradation curves and scanning electron microscopy (SEM) images further demonstrated the biodegradability of PBM, which have different crystal structures. The hardness of PBM-2 implied the potential application in bone regeneration, while it resulted in the reduction of solubility when compared with PBM-1, which made it difficult to be dissolved and hydrogenated. The solution was therefore heated up to 75 °C to achieve benzyl deprotection, and a series of partially hydrogenated PBM was sequent prepared. Their optimal hydrogenation rates were screened to determine the optimal conditions for the formation of micelles suitable for drug-carrier applications. In summary, the synthesis route from malic acid facilitated the production of PBM for a shorter time and with a higher yield. The biodegradability, biosafety, mechanical properties, and adjustable hydrogenation widen the application of PBM with tunable properties as drug carriers.

Biodegradable Polymersomes with Structure Inherent Fluorescence and Targeting Capacity for Enhanced Photo-Dynamic Therapy.

Biodegradable nanostructures displaying aggregation-induced emission (AIE) are desirable from a biomedical point of view, due to the advantageous features of loading capacity, emission brightness, and fluorescence stability. Herein, biodegradable polymers comprising poly (ethylene glycol)-block-poly(caprolactone-gradient-trimethylene carbonate) (PEG-P(CLgTMC)), with tetraphenylethylene pyridinium-TMC (PAIE) side chains have been developed, which self-assembled into well-defined polymersomes. The resultant AIEgenic polymersomes are intrinsically fluorescent delivery vehicles. The presence of the pyridinium moiety endows the polymersomes with mitochondrial targeting ability, which improves the efficiency of co-encapsulated photosensitizers and improves therapeutic index against cancer cells both in vitro and in vivo. This contribution showcases the ability to engineer AIEgenic polymersomes with structure inherent fluorescence and targeting capacity for enhanced photodynamic therapy.

Progress in the Preparation of Functional and (Bio)Degradable Polymers via Living Polymerizations.

This review presents the latest developments in (bio)degradable approaches and functional aliphatic polyesters and polycarbonates prepared by typical ring-opening polymerization (ROP) of lactones and trimethylene carbonates. It also considers several recent innovative synthetic methods including radical ring-opening polymerization (RROP), atom transfer radical polyaddition (ATRPA), and simultaneous chain- and step-growth radical polymerization (SCSRP) that produce aliphatic polyesters. With regard to (bio)degradable approaches, we have summarized several representative cleavable linkages that make it possible to obtain cleavable polymers. In the section on functional aliphatic polyesters, we explore the syntheses of specific functional lactones, which can be performed by ring-opening copolymerization of typical lactone/lactide monomers. Last but not the least, in the recent innovative methods section, three interesting synthetic methodologies, RROP, ATRPA, and SCSRP are discussed in detail with regard to their reaction mechanisms and polymer functionalities.

Synthesis, Properties, and Biodegradation of Sequential Poly(Ester Amide)s Containing γ-Aminobutyric Acid.

Poly(ester amide)s are attracting attention because they potentially have excellent thermal and mechanical properties as well as biodegradability. In this study, we synthesized a series of novel poly(ester amide)s by introducing γ-aminobutyric acid (GABA) regularly into polyesters, and investigated their properties and biodegradabilities. GABA is the monomer unit of biodegradable polyamide 4 (PA4). The new poly(ester amide)s were synthesized from the reaction of ammonium tosylate derivatives of alkylene bis(γ-aminobutylate) and p-nitrophenyl esters of dicarboxylic acids. All the obtained polymers showed relatively high melting temperatures (Tm). Their thermal decomposition temperatures were improved in comparison with that of PA4 and higher enough than their Tm. The poly(ester amide)s exhibited higher biodegradability in seawater than the corresponding homopolyesters. Their biodegradabilities in activated sludge were also studied.

Use of a Mixture of Polyols Based on Metasilicic Acid and Recycled PLA for Synthesis of Rigid Polyurethane Foams Susceptible to Biodegradation.

Two polyol raw materials were obtained in the conducted research, one based on metasilicic acid (MSA), the other based on poly(lactic acid) (PLA) waste. The obtained polyols were characterized in terms of their applicability for the production of rigid polyurethane foams (RPUFs). Their basic analytical properties (hydroxyl number, acid number, elemental analysis) and physicochemical properties (density, viscosity) were determined. The assumed chemical structure of the obtained new compounds was confirmed by performing FTIR and 1H NMR spectroscopic tests. Formulations for the synthesis of RPUFs were developed on the basis of the obtained research results. A mixture of polyols based on MSA and PLA in a weight ratio of 1:1 was used as the polyol component in the polyurethane formulation. The reference foam in these tests was a foam that was synthesized only on the basis of MSA-polyol. The obtained RPUFs were tested for basic functional properties (apparent density, compressive strength, water absorption, thermal conductivity coefficient etc.). Susceptibility to biodegradation in soil environment was also tested. It was found that the use of mixture of polyols based on MSA and PLA positively affected the properties of the obtained foam. The polyurethane foam based on this polyol mixture showed good thermal resistance and significantly reduced flammability in comparison with the foam based MSA-polyol. Moreover, it showed higher compressive strength, lower thermal conductivity and biodegradability in soil. The results of the conducted tests confirmed that the new foam was characterized by very good performance properties. In addition, this research provides information on new waste management opportunities and fits into the doctrine of sustainable resource management offered by the circular economy.

Slicing parameter optimization for 3D printing of biodegradable drug-eluting tracheal stents.

In 3D printing, the schematic representation of an object must be converted into machine commands. This process is called slicing. Depending on the slicing parameters, products with different properties are obtained. In this work, biodegradable drug-eluting tracheal stents consisting of a medical grade poly(lactic-co-glycolic acid) and a drug were printed by fused deposition modeling. A slicing parameter optimization method was proposed with the aim of obtaining a particularly low stent porosity and high mechanical strength while maintaining the stent dimensions, which is essential regarding patient-tailored implants. Depending on the three slicing parameters printing pattern, lateral strand distance and spatial fill, porosities of approximately 2-5% were obtained. The tensile strength was used as a measure for the mechanical strength of the implants and was found to be dependent on the porosity as well as the strand orientation relative to the load direction. Strand orientations in load direction yielded the highest tensile strengths of 40-46 MPa and the bonding between individual layers yielded the lowest tensile strengths of 20-24 MPa. In vitro dissolution tests of successfully printed stents were used to predict sustained release of the drug over several months.

Rational design and characterization of bioplastics from Hermetia illucens prepupae proteins.

In this study proteins extracted from prepupae of Hermetia illucens, also known as black soldier fly, are investigated as promising base for a new type of bioplastics for agricultural purposes. Design of experiments techniques are employed to perform a rational study on the effects of different combination of glycerol as plasticizer, citric acid as cross-linking agent and distilled water as solvent on the capability of proteins to form a free-standing film through casting technique, keeping as fixed the quantity of proteins. Glycerol shows interesting properties as plasticizer contributing to the formation of homogenous and free-standing film. Moreover, mechanical and thermal characterizations are performed to estimate the effect of increasing amounts of proteins on the final properties and thickness of the specimens. Proteins derived from H. illucens can be successfully employed as base for bioplastics to be employed for agricultural purposes.

Functional, Degradable Zwitterionic Polyphosphoesters as Biocompatible Coating Materials for Metal Nanostructures.

A zwitterionic polyphosphoester (zPPE), specifically l-cysteine-functionalized poly(but-3-yn-1-yloxy)-2-oxo-1,3,2-dioxaphospholane (zPBYP), has been developed as a poly(ethylene glycol) (PEG) alternative coating material for gold nanoparticles (AuNPs), the most extensively investigated metal nanoparticulate platform toward molecular imaging, photothermal therapy, and drug delivery applications. Thiol-yne conjugation of cysteine transformed an initial azido-terminated and alkynyl-functionalized PBYP homopolymer into zPBYP, offering hydrolytic degradability, biocompatibility, and versatile reactive moieties for installation of a range of functional groups. Despite minor degradation during purification, zPPEs were able to stabilize AuNPs presumably through multivalent interactions between combinations of the side chain zwitterions (thioether and phosphoester groups of the zPPEs with the AuNPs). 31P NMR studies in D2O revealed ca. 20% hydrolysis of the phosphoester moieties of the repeat units had occurred during the workup and purification by aqueous dialysis at pH 3 over ca. 1 d, as observed by the 31P signal of the phosphotriesters resonating at ca. -0.5 to -1.7 shifting downfield to ca. 1.1 to -0.4 ppm, attributed to transformation to phosphates. Further hydrolysis of side chain and backbone units proceeded to an extent of ca. 75% over the next 2 d in nanopure water (pH 5-6). The NMR degradation results were consistent with the broadening and red-shift of the surface plasmon resonance (SPR) observed by UV-vis spectroscopy of the zPPE-coated AuNPs in water over time. All AuNP formulations in this study, including those with citrate, PEG, and zPPE coatings, exhibited negligible immunotoxicity, as determined by cytokine overexpression in the presence of the nanostructures relative to those in cell culture medium. Notably, the zPPE-coated AuNPs displayed superior antifouling properties, as assessed by the extent of cytokine adsorption relative to both the PEGylated and citrate-coated AuNPs. Taken together, the physicochemical and biological evaluations of zPPE-coated AuNPs in conjunction with PEGylated and citrate-coated analogues indicate the promise of zPPEs as favorable alternatives to PEG coatings, with negligible immunotoxicity, good antifouling performance, and versatile reactive groups that enable the preparation of highly tailored nanomaterials for diverse applications.

Zwitterionic Cross-Linked Biodegradable Nanocapsules for Cancer Imaging.

Zwitterionic cross-linked biodegradable nanocapsules (NCs) were synthesized for cancer imaging. A polylactide (PLA)-based diblock copolymer with two blocks carrying acetylenyl and allyl groups respectively was synthesized by ring-opening polymerization (ROP). Azide-alkyne "click" reaction was conducted to conjugate sulfobetaine (SB) zwitterions and fluorescent dye Cy5.5 onto the acetylenyl-functionalized first block of the diblock copolymer. The resulting copolymer with a hydrophilic SB/Cy5.5-functionalized PLA block and a hydrophobic allyl-functionalized PLA block could stabilize miniemulsions because of its amphiphilic diblock structure. UV-induced thiol-ene "click" reaction between a dithiol cross-linker and the hydrophobic allyl-functionalized block of the copolymer at the peripheral region of nanoscopic oil nanodroplets in the miniemulsion generated cross-linked polymer NCs with zwitterionic outer shells. These NCs showed an average hydrodynamic diameter ( Dh) of 136 nm. They exhibited biodegradability, biocompatibility and high colloidal stability. In vitro study indicated that these NCs could be taken up by MIA PaCa-2 cancer cells. In vivo imaging study showed that, comparing to a small molecule dye, NCs had a longer circulation time, facilitating their accumulation at tumors for cancer imaging. Overall, this work demonstrates the applicability of zwitterionic biodegradable polymer-based materials in cancer diagnosis.

Plasticized Cellulosic Films by Partial Esterification and Welding in Low-Concentration Ionic Liquid Electrolyte.

Alternatives to petroleum-based plastics are of great significance not only from the point of view of their scientific and practical impact but to reduce the environmental footprint. Inspired by the composition and structure of wood's cell walls, we used phenolic acids to endow cellulosic fibers with new properties. The fiber dissolution and homogeneous modification were performed with a recyclable ionic liquid (IL) (tetrabutylammonium acetate ([N4444][OAc]):dimethyl sulfoxide) to attain different levels of reaction activity for three phenolic acids ( p-hydroxybenzoic acid, vanillic acid, and syringic acid). The successful autocatalytic Fischer esterification reaction was thoroughly investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, elemental analysis, and nuclear magnetic resonance spectroscopy (13C CP-MAS, diffusion-edited 1H NMR and multiplicity-edited heteronuclear single quantum coherence). Control of the properties of cellulose in the dispersed state, welding, and IL plasticization were achieved during casting and recrystallization to the cellulose II crystalline allomorph. Films of cellulose carrying grafted acids were characterized with respect to properties relevant to packaging materials. Most notably, despite the low degree of esterification (DS < 0.25), the films displayed a remarkable strength (3.5 GPa), flexibility (strains up to 35%), optical transparency (>90%), and water resistance (WCA ∼ 90°). Moreover, the measured water vapor barrier was found to be similar to that of poly(lactic acid) composite films. Overall, the results contribute to the development of the next-generation green, renewable, and biodegradable films for packaging applications.

Tunable and Selective Degradation of Amine-Reactive Multilayers in Acidic Media.

We report the design of reactive and hydrolytically degradable multilayers by the covalent layer-by-layer assembly of an azlactone-containing polymer, poly(2-vinyl-4,4-dimethylazlactone), with an acid-degradable, acetal-containing, small-molecule diamine linker. This approach yields cross-linked multilayers that contain (i) residual azlactone reactivity that can be used for further functionalization after fabrication and (ii) acid-labile cross-links that can undergo pH-triggered degradation. Thin films and hollow capsules fabricated using this approach were relatively stable in slightly basic media (pH = 7.4) but eroded and degraded gradually in mildly acidic environments (pH = 5). The residual azlactones in these materials could be functionalized by reaction with hydrophilic or hydrophobic amines to tune physicochemical properties, including surface wetting and rates of degradation/erosion. Interestingly, our results reveal that rates of degradation could be tuned over a broad range (from ∼4 h to ∼10 days) simply by post-fabrication modification of the parent reactive material. We further demonstrate the potential of acetal-containing microcapsules to be used for the acid-triggered release of encapsulated cargo. The results of in vitro experiments reveal that microcapsules loaded with fluorescently labeled dextran can be internalized by mammalian cells and that cell uptake and intracellular degradation were also influenced by the types of functional groups installed post-fabrication. The introduction of acid degradability expands the range of stimuli that can be used to trigger the destruction of these reactive materials to include changes in pH relevant to chemical and biological processes. Our results also introduce an approach to tuning degradation profiles that differs from past strategies used to design degradable multilayers. We conclude that this approach provides a new, useful, and modular platform for the design of stimuli-responsive nano/biointerfaces with transient environmental stability.

Modification of Poly(ethylene 2,5-furandicarboxylate) with Biobased 1,5-Pentanediol: Significantly Toughened Copolyesters Retaining High Tensile Strength and O2 Barrier Property.

Poly(ethylene 2,5-furandicarboxylate) (PEF) is a biobased polyester characterized by high gas barrier properties as well as high tensile modulus and strength, but poor toughness. Toughening PEF without sacrificing its modulus, strength and gas barrier performance is a great challenge for PEF modification. In this study, high molecular weight random poly(ethylene- co-1,5-pentylene 2,5-furandicarboxylate)s (PEPeFs) were synthesized via melt copolycondensation of 2,5-furandicarboxylic acid (FDCA), ethylene glycol (EG) and 1,5-pentanediol (PeDO), a cheap, biobased and commercially available odd-carbon comonomer. The synthesized PEPeFs were characterized and assessed with intrinsic viscosity, ATR-FTIR, 1H NMR, DSC, TGA and tensile, impact and O2 permeation test. Mayo-Lewis equation with "reactivity ratio" of 3.78 for PeDO and 0.75 for EG could be used as an empirical equation to correlate the copolyester composition (ϕPeF) with monomer composition. PEPeFs proved nearly amorphous copolyesters having excellent thermal stability. Brittle-ductile transition was achieved at ϕPeF as low as 9 mol %. Increasing ϕPeF led to increase in elongation at break and notch impact strength and decrease in Tg, O2 barrier performance and tensile modulus and strength. However, in comparison with PEF, PEF-rich PEPeFs (ϕPeF 9-47%) not only showed greatly improved elongation at break (29-265% vs 4%) and enhanced impact strength (2.2-3.9 kJ/m2) but also retained very high Young's modulus (2.8-3.3 vs 3.3 GPa) and yielding strength (72-83 vs 82 MPa). Particularly, when compared with bottle-grade PET, PE82Pe18F possesses equal Tg (ca. 75 °C) and comparable elongation at break (ca. 115%), but greatly improved yielding strength (83 MPa) and O2 gas barrier property (4.8 times). As modified PEF materials possessing superior thermo-mechanical and O2 gas barrier properties, these integrally biobased copolyesters may find practical applications in eco-packaging and other fields.

Azide-Substituted Polylactide: A Biodegradable Substrate for Antimicrobial Materials via Click Chemistry Attachment of Quaternary Ammonium Groups.

Polylactide (PL) co-polymers substituted with pendant azide groups (azido-PL) were synthesized by the nucleophilic conjugate addition of 3-azido-1-propanethiol to a co-polymer of PL containing α,ß-unsaturated ester units, poly(lactide-co-methylene glycolide) (ene-PL) that is obtained from the base-promoted dehydrochlorination of poly(lactide-co-chlorolactide) (chloro-PL). Alternatively, azido-PL was prepared by the treatment of chloro-PL with 3-azido-1-propanethiol without isolation of the ene-PL intermediate. The azido-PL was functionalized by copper-catalyzed [3 + 2] cycloaddition reactions with four alkynes: propargyl 4-methoxybenzoate, N,N,N-trimethyl-N-propargylammonium bromide, N,N-dimethyl-N-octyl-N-propargylammonium bromide, and N,N,N-trioctyl-N-propargylammonium bromide. Polymer adducts with N,N,N-trioctyl-N-propargylammonium bromide displayed potent antimicrobial activity both in suspension and as a polymer film.

Harnessing the Chemical Diversity of the Natural Product Magnolol for the Synthesis of Renewable, Degradable Neolignan Thermosets with Tunable Thermomechanical Characteristics and Antioxidant Activity.

Magnolol, a neolignan natural product with antioxidant properties, contains inherent, orthogonal, phenolic, and alkenyl reactive groups that were used in both direct thermoset synthesis, as well as the stepwise synthesis of a small library of monomers, followed by transformation into thermoset materials. Each monomer from the small library was prepared via a single step functionalization reaction of the phenolic groups of magnolol. Thermoset materials were realized through solvent-free, thiol-ene reactions, and the resulting cross-linked materials were each comprised of thioether and ester linkages, with one retaining the hydrophilic phenols from magnolol, another having the phenols protected as an acetonide, and two others incorporating the phenols into additional cross-linking sites via hydrolytically labile carbonates or stable ether linkages. With this diversity of chemical compositions and structures, the thermosets displayed a range of thermomechanical properties including glass transition temperatures, Tg, 29-52 °C, onset of thermal degradation, Td, from about 290-360 °C, and ultimate strength up to 50 MPa. These tunable materials were studied in their degradation and biological properties with the aim of exploiting the antioxidant properties of the natural product. Hydrolytic degradation occurred under basic conditions (pH = 11) in all thermosets, but with kinetics that were dependent upon their chemical structures and mechanical properties: 20% mass loss was observed at 5, 7, 27, and 40 weeks for the thermosets produced from magnolol directly, acetonide-protected magnolol, bis(allyl carbonate)-functionalized magnolol, and bis(allyl ether)-functionalized magnolol, respectively. Isolated degradation products and model compounds displayed antioxidant properties similar to magnolol, as determined by both UV-vis and in vitro reactive oxygen species (ROS) assays. As these magnolol-based thermosets were found to also allow for extended cell culture, these materials may serve as promising degradable biomaterials.

Degradable and Injectable Hydrogel for Drug Delivery in Soft Tissues.

Injectable hydrogels are promising platforms for tissue engineering and local drug delivery as they allow minimal invasiveness. We have here developed an injectable and biodegradable hydrogel based on an amphiphilic PNIPAAm- b-PLA- b-PEG- b-PLA- b-PNIPAAm pentablock copolymer synthesized by ring-opening polymerization/nitroxide-mediated polymerization (ROP/NMP) combination. The hydrogel formation at around 30 °C was demonstrated to be mediated by intermicellar bridging through the PEG central block. Such a result was particularly highlighted by the inability of a PEG- b-PLA- b-PNIPAAm triblock analog of the same composition to gelify. The hydrogels degraded through hydrolysis of the PLA esters until complete mass loss due to the diffusion of the recovered PEG and PNIPAAm/micelle based residues in the solution. Interestingly, hydrophobic molecules such as riluzole (neuroprotective drug) or cyanine 5.5 (imaging probe) could be easily loaded in the hydrogels' micelle cores by mixing them with the copolymer solution at room temperature. Drug release was correlated to polymer mass loss. The hydrogel was shown to be cytocompatible (neuronal cells, in vitro) and injectable through a small-gauge needle (in vivo in rats). Thus, this hydrogel platform displays highly attractive features for use in brain/soft tissue engineering as well as in drug delivery.

Development of superabsorbent soy protein-based bioplastic matrices with incorporated zinc for horticulture.

BACKGROUND: The use of superabsorbent materials in horticulture has spread recently. These materials, which can retain water and release it as crops need it, have strong advantages such as the efficient use of water in periods of drought. However, these materials are made of synthetic polymers, which present problems of degradability and, sometimes, toxicity. For this reason, the main objective of this work is the development of biodegradable superabsorbent bioplastic (SAB) matrices using a soy protein isolate (SPI) as raw material. Zinc is also incorporated into these bioplastic matrices as an essential micronutrient for plants, to increase their added value. RESULTS: The incorporation of zinc chelated with 2,2',2″,2‴-(Ethene-1,2-diyldinitrilo)tetraacetic acid (Zn EDTA) (a salt with which the micronutrient is incorporated) into soy protein-based bioplastic matrices improved their superabsorbent capacity and provided a controlled release of water and nutrients to the crops. CONCLUSIONS: The results show the strong potential for the use of these bioplastic matrices in horticulture as superabsorbent materials that can release nutrients in a controlled manner. © 2019 Society of Chemical Industry.

Biodegradable, Hydrogen Peroxide, and Glutathione Dual Responsive Nanoparticles for Potential Programmable Paclitaxel Release.

Reactive oxygen species (ROS) and glutathione (GSH) dual responsive nanoparticulate drug delivery systems (nano-DDSs) hold great promise to improve the therapeutic efficacy and alleviate the side effects of chemo drugs in cancer theranosis. Herein, hydrogen peroxide (H2O2) and GSH dual responsive thioketal nanoparticle (TKN) was rationally designed for paclitaxel (PTX) delivery. Compared to other stimuli-sensitive nano-DDSs, this dual responsive DDS is not only sensitive to biologically relevant H2O2 and GSH for on-demand drug release but also biodegradable into biocompatible byproducts after fulfilling its delivering task. Considering the heterogeneous redox potential gradient, the PTX loaded TKNs (PTX-TKNs) might first respond to the extracellular ROS and then to the intracellular GSH, achieving a programmable release of PTX at the tumor site. The selective toxicity of PTX-TKNs to tumor cells with high levels of ROS and GSH was verified both in vitro and in vivo.