RESUMO
BACKGROUND The aim of this study was to assess and compare the vertical/horizontal dimensions and occlusal accuracy of non-working/opposing casts obtained from three different impression materials and 3D print cast. MATERIAL AND METHODS Dentulous Master models simulating a case of a fixed dental prosthesis were mounted on an articulator (control group). Opposing mandibular casts obtained from three different impression materialsand 3-dimensional print constituted test groups , ,and , respectively. Three points, anterior vertical (AV), posterior vertical (PV), and anteroposterior (AP) were compared for dimensional accuracy among casts. Occlusal accuracy was analyzed on Medit Link software at 3 teeth (#13, #17, and #27). After calculating means for each group, the differences were calculated at probability value of P≤0.05 using the single-sample t test, ANOVA, and Tukey test. RESULTS The dimensions were significantly different from those of the mounted master models except in Gp AL(E) and Gp AL(F) at AV dimension and Gp AL(E) at AP dimension (P>0.05). A statistically significant difference of the error of means among the 4 tested groupswere detected only at 2 dimensions (AV and PV) between the Gp AL(E) and Gp 3D-C and between Gp AL(F) and Gp 3D-C groups. Other groups showed no significant differences. CONCLUSIONS The opposing casts obtained from the extended-pour alginate and alginate alternative impression materials showed higher occlusal accuracy compared to conventional alginate and 3D printed casts.
Assuntos
Modelos Dentários , Impressão Tridimensional , Humanos , Alginatos , Mandíbula , SoftwareRESUMO
BACKGROUND This study, employing an online questionnaire, aimed to assess and contrast the awareness, knowledge, and perceptions of dentists in Saudi Arabia (SA) regarding endocrowns (EC) as post-endodontic restorations with those of dentists educated in various other countries. MATERIAL AND METHODS We conducted a cross-sectional survey among dental interns and practicing dentists in government facilities, private dental centers, and dental colleges in SA, including participants of diverse nationalities. We disseminated validated, closed-ended questionnaires through WhatsApp via Google Forms. The Chi-square test was applied to assess associations between categorical variables, with a P-value of ≤0.05 indicating statistical significance. RESULTS The majority of participants (61.2%) indicated that EC restorations are best suited for molar teeth. Furthermore, 69.6% asserted that the primary objective of employing EC is to accomplish minimally invasive preparations while preserving the existing tooth structure. Among the responses, 68.3% pinpointed debonding of ECs as a significant cause of failure. Notably, substantial differences were observed in responses concerning the knowledge or practice of EC across various factors such as gender, educational attainment, country of graduation, and workplace. CONCLUSIONS The findings reveal a comparatively low adoption of ECs among the participants, irrespective of experience or country of education. This underscores the need for incorporating ECs into dental curricula through theoretical and clinical discussions or considering them as a subject for post-graduate continuing education programs.
Assuntos
Currículo , Dente Molar , Humanos , Estudos Transversais , Escolaridade , OdontólogosRESUMO
BACKGROUND The ratio between a tooth root and its crown is an essential diagnostic parameter that determines treatment options. This radiographic study used panoramic dental radiographs or orthopantograms to measure the mean root (R)-to-crown (C) ratios (R/C) of the permanent teeth in 81 Saudi adults. MATERIAL AND METHODS A total of 81 panoramic radiographs of Saudi adult patients (40 males and 41 females) previously treated in the College of Dentistry, Saudi Arabia, aged 16-35 years, were selected. The crown height and root length for each tooth were measured on the digital panoramic radiographs. The correlation coefficient (intra-class) was calculated to assess the intra-examiner reproducibility and a good agreement was achieved (ICC=0.79-0.89). RESULTS For both males and females, the highest mean R/C ratio was for maxillary canine (1.91) and for mandibular second premolar (2.0) while the lowest R/C ratio was for maxillary first molar (1.64) and for mandibular central incisor (1.59). Except for the maxillary second premolar, no significant differences in R/C ratios were observed for maxillary arch. In the mandibular arch, the R/C ratio for lateral incisor, both premolars, and molars differed significantly (P<0.05). Among males, statistically significant differences between teeth existed in R/C ratios for central and lateral incisors, second premolar, and both molars (P>0.05). For females, significant differences between teeth in R/C ratios were observed for both premolars and both molars (P>0.05). CONCLUSIONS This study supports the findings from previous studies that orthopantograms can be used to calculate root/crown ratios, which varies between males and females and the dental arch among Saudi adults.
Assuntos
Dentição Permanente , Radiografia Panorâmica/métodos , Coroa do Dente/diagnóstico por imagem , Adolescente , Adulto , Feminino , Seguimentos , Humanos , Masculino , Reprodutibilidade dos Testes , Estudos Retrospectivos , Arábia Saudita , Adulto JovemRESUMO
The aim of this study is to investigate the combined effect of a digital manufacturing technique (subtractive vs. additive), preparation taper (10° vs. 20° TOC), and finish line (chamfer vs. shoulder) on the marginal adaptation of temporary crowns following cementation with a compatible temporary cement. Four mandibular first molar typodont teeth were prepared for full coverage crowns with standard 4 mm preparation height as follows: 10° TOC with the chamfer finish line, 10° TOC with the shoulder finish line, 20° TOC with the chamfer finish line and 20° TOC with the shoulder finish line. Each of the four preparation designs were subdivided into two subgroups to receive CAD/CAM milled and 3D-printed crowns (n = 10). A total of 80 temporary crowns (40 CAD/CAM milled and 40 3D-printed) were cemented to their respective die using clear temporary recement in the standard cementation technique. The samples were examined under a stereomicroscope at ×100 magnification following calibration. Linear measurements were performed at seven equidistant points on each axial surface and five equidistant points on each proximal surface. One-way ANOVA analysis and Tukey HSD (Honestly Significance Difference) were performed. The best marginal fit was seen in group 8, while the poorest fit was noted in group 2. Shoulder finish lines and 10° TOC resulted in higher marginal gaps, especially in CAD/CAM milled group. The selection of 3D-printed crowns may provide a better marginal fit within the range of clinical acceptability. Marginal gaps were within clinical acceptability (50 and 120 µm) in all groups except group 2.
RESUMO
This study aimed to evaluate the effect of three oral hygiene tools, a regular toothbrush, an electronic toothbrush, and mouthwash, on the color stability of three different computer-aided design (CAD) and computer-aided manufactured (CAM) ceramic blocks. Feldspathic ceramic (Vita Triluxe Forte), hybrid resin ceramic (Vita Enamic), and lithium disilicate glass-ceramic (IPS e.max CAD) were used in this study. A CAD/CAM system and 81 (27 of each material) samples of ceramic blocks were used. All samples were immersed in black coffee for 15 days, and the coffee was changed twice per day. Using a spectrophotometer probe, samples on a grey background were scanned, and physical properties like surface hardness and depth were measured using interferometry and a 3D non-contact surface metrology. After 30 days of application of oral hygiene tools, instruments were used to measure various physical, mechanical, and optical properties. Vita Triluxe had the highest average color variation values (ΔE00) after 15 and 30 days of immersion in coffee in both regular and electronic toothbrushes. Moreover, IPS e.max CAD had the least ΔE00 values with no significant differences among the groups. The surface roughness (Ra) of the Vita Enamic ceramic increased when using a regular toothbrush, and the surface height (Rz) for the Vita Enamic ceramic increased when an electronic toothbrush was used. IPS e.max CAD had the greatest modules of elasticity forces, and Vita Triluxe Forte had the lowest when used with a regular toothbrush. The ΔE00 values of the tested materials were minimally increased or decreased after 30 days of cleaning, and all were clinically acceptable. Ra and Rz were the highest for Vita Enamic in comparison to the other groups. The highest percentage in IPS e.max CAD was associated with a type 1 fracture, whereas type 3 was predominantly observed with Vita Enamic, and type 2 in the Vita Triluxe group without significant differences.
Assuntos
Café , Imersão , Teste de Materiais , Higiene Bucal , CerâmicaRESUMO
Healthcare workers have reported a certain segment of geriatric patients that are suffering from abuse/neglect, which in turn has been associated with anxiety, depression, and helplessness in the individual. Family caregivers (blood relations), being the most common perpetrators of elder abuse and neglect (EAN), have also been shown to respond to sensitization if the type of EAN and the interventions are appropriate. This study was aimed to comparatively analyze the influence of intervention (psychotherapeutic sensitization of FCG) upon long-term (24 months) treatment maintenance and satisfaction in elderly neglected patients. One hundred and fifty patients (aged 41-80 years) suffering from elder neglect (EN) (self-confession) and their respective FCGs, fulfilling the study criteria, participated in this longitudinal 2-year study. The patients were randomly distributed (simple random, convenient) in two equal groups (75 each), namely Group (GP) A (control) and GP B (test). A standardized, complete denture treatment was initiated for all the participants. Both the FCGs and the patients of GP B were sensitized (psychotherapeutic education) for EN, while there was no such intervention in GP A. The influence of such intervention was measured for denture maintenance [denture plaque index (DPI) scores] and treatment satisfaction (10-point visual analog scale). Absolute/relative frequencies and means were major calculations during data analysis. Differences between the groups for any treatment compliance parameter was done through the unpaired t-test, while Karl Pearson's test determined the level of relationship between variables (p-value < 0.05). Decrease in mean DPI scores (suggesting improvement) was seen among patients in GP A from 1 month (m = 2.92) to 24 months (m = 2.77). A negligible increase in DPI scores was observed among patients of GP B from 1 month (m = 1.38) to 24 months (m = 1.44). Differences in mean values between the two groups were statistically significant at 24-month intervals, while the relationship between the variables was nonsignificant. FCG sensitization through psychotherapeutic education shows a long-term positive influence on the treatment compliance (maintenance and satisfaction). Identifying the existence of EAN among geriatric patients, followed by psychotherapeutic education of FCGs is recommended for routine medical and dental long-duration treatment procedures.
RESUMO
PURPOSE: This study investigated the occlusal fracture resistance of Turkom-Cerafused alumina compared to Procera AllCeram and In-Ceram all-ceramic restorations. MATERIALS AND METHODS: Sixmaster dies were duplicated from the prepared maxillary first premolar tooth using nonprecious metal alloy (Wiron 99). Ten copings of 0.6 mm thickness were fabricated from each type of ceramic, for a total of thirty copings. Two master dies were used for each group, and each of them was used to lute five copings. All groups were cemented with resin luting cement Panavia F according to manufacturer's instructions and received a static load of 5 kg during cementation. After 24 hours of distilled water storage at 37 degrees C, the copings were vertically compressed using a universal testing machine at a crosshead speed of 1 mm/min. RESULTS: The results of the present study showed the following mean loads at fracture: Turkom-Cera (2184 +/- 164 N), In-Ceram (2042 +/- 200 N), and Procera AllCeram (1954 +/- 211 N). ANOVA and Scheffe's post hoc test showed that the mean load at fracture of Turkom-Cera was significantly different from Procera AllCeram (p < 0.05). Scheffe's post hoc test showed no significant difference between the mean load at fracture of Turkom-Cera and In-Ceram or between the mean load at fracture of In-Ceram and Procera AllCeram. CONCLUSION: Because Turkom-Cera demonstrated equal to or higher loads at fracture than currently accepted all-ceramic materials, it would seem to be acceptable for fabrication of anterior and posterior ceramic crowns.
Assuntos
Força Compressiva , Coroas , Dente Suporte , Porcelana Dentária , Falha de Restauração Dentária , Óxido de Alumínio , Análise de Variância , Colagem Dentária , Porcelana Dentária/classificação , Planejamento de Prótese Dentária , Análise do Estresse Dentário/métodos , Humanos , Estatísticas não Paramétricas , Estresse MecânicoRESUMO
AIM: The objective of this study is to investigate the effect of different luting agents on the fracture strength of Turkom-Cera all-ceramic copings. METHODS AND MATERIALS: Standardized metal dies were duplicated from a prepared maxillary first premolar tooth using non-precious metal alloy (Wiron 99). Thirty Turkom-Cera copings of 0.6 mm thickness were then fabricated. Three types of luting agents were used: zinc phosphate cement (Elite), glass-ionomer cement (Fuji I), and a dual-cured composite resin cement (Panavia F). Ten copings were cemented with each type. All copings were cemented to their respective dies according to manufacturer's instructions and received a static load of 5 kg for ten minutes. After 24 hours of storage in distilled water at 37 degrees C, the copings were vertically loaded until fracture using an Instron Universal Testing Machine at a crosshead speed of 1 mm/minute. The mode of fracture was then determined. RESULTS: Statistical analysis carried out using analysis of variance (ANOVA) revealed significant differences in the compressive strength between the three groups (P<0.001). The mean fracture strength (in Newtons) of Turkom-Cera copings cemented with Elite, Fuji I, and Panavia F were 1537.4 N, 1294.4 N, and 2183.6 N, respectively. CONCLUSIONS: Luting agents have an influence on the fracture resistance of Turkom-Cera copings.
Assuntos
Cimentação , Coroas , Porcelana Dentária , Cimentos de Ionômeros de Vidro , Cimentos de Resina , Cimento de Fosfato de Zinco , Óxido de Alumínio , Análise de Variância , Dente Pré-Molar , Distribuição de Qui-Quadrado , Força Compressiva , Análise do Estresse Dentário , Humanos , Teste de Materiais , Silanos , Estatísticas não ParamétricasRESUMO
BACKGROUND: The selection of the appropriate luting cement is a key factor for achieving a strong bond between prepared teeth and dental restorations. AIM: To evaluate the shear bond strength of Zinc phosphate cement Elite, glass ionomer cement Fuji I, resin-modified glass ionomer cement Fuji Plus and resin luting cement Panavia-F to Turkom-Cera all-ceramic material. MATERIALS AND METHODS: Turkom-Cera was used to form discs 10mm in diameter and 3 mm in thickness (n = 40). The ceramic discs were wet ground, air - particle abraded with 50 - µm aluminium oxide particles and randomly divided into four groups (n = 10). The luting cement was bonded to Turkom-Cera discs as per manufacturer instructions. The shear bond strengths were determined using the universal testing machine at a crosshead speed of 0.5 mm/min. The data were analysed using the tests One Way ANOVA, the nonparametric Kruskal - Wallis test and Mann - Whitney Post hoc test. RESULTS: The shear bond strength of the Elite, Fuji I, Fuji Plus and Panavia F groups were: 0.92 ± 0.42, 2.04 ± 0.78, 4.37 ± 1.18, and 16.42 ± 3.38 MPa, respectively. There was the statistically significant difference between the four luting cement tested (p < 0.05). CONCLUSION: the phosphate-containing resin cement Panavia-F exhibited shear bond strength value significantly higher than all materials tested.
RESUMO
OBJECTIVES: The study aimed to evaluate and compare the dental prosthetic status and treatment needs of adult population in Jizan, Saudi Arabia, in relation to the age. MATERIALS AND METHODS: A total of 1779 people aged 35-74 years from 4 survey areas (Hay al matar, Mahata khams, Dara ut tawhid, and Suq ad dakhili) selected through convenient sampling, around Jizan University, were surveyed, using the WHO survey criteria, 1997. STATISTICAL ANALYSIS: Number and percentages were calculated, and univariate analysis was performed using Chi-square test at 5% level of significance. RESULTS: Different forms of prosthesis were present among patients in the upper (19.9%) and lower (19%) arches, respectively. Prosthetic treatment need was recognized in subjects, 56.4% for the upper and 57.2% for the lower arches, respectively. The prosthetic status and treatment needs differed statistically with respect to age. CONCLUSION: More than half of the surveyed adult populations were in need of some or the other forms of prosthesis. This study provides data for an oral health-care provider program for Jizan.
RESUMO
The aim of this study was to evaluate the marginal adaptation of Turkom-Cera all-ceramic crowns compared to In-Ceram and Procera AllCeram systems. The influence of finish line design (chamfer or shoulder) on the marginal adaptation of Turkom-Cera all-ceramic crowns was also investigated. Thirty human premolars were prepared with chamfer margins and assigned to either the Turkom-Cera, In-Ceram, or Procera system group. In addition, 10 premolars were prepared with rounded shoulder finish lines and assigned to an additional Turkom-Cera group. Ceramic copings (0.6-mm thick) were fabricated for each group following the manufacturers' instructions. The copings were seated on abutments using a special holding device that facilitated uniform loading, and marginal adaptation was assessed using a stereomicroscope. Data were analyzed using analysis of variance, the Tukey HSD post hoc test, and an independent samples t test. There was a statistically significant difference regarding marginal adaptation among the three all-ceramic systems (P < .05). There were no significant differences in the mean marginal discrepancies of Turkom-Cera crowns among chamfer and shoulder finish line groups (P > .05). Within the limitations of this study, the marginal discrepancies were all within the clinically acceptable standard. Int J Prosthodont 2011;24:379-381.
Assuntos
Coroas , Planejamento de Prótese Dentária , Cerâmica , Adaptação Marginal Dentária , HumanosRESUMO
PURPOSE: The current study investigated the effect of different luting agents on the fracture resistance of Procera AllCeram copings. METHODS: Six master dies were duplicated from the prepared maxillary first premolar tooth using nonprecious metal alloy (Wiron 99). Thirty copings (Procera AllCeram) of 0.6-mm thickness were manufactured. Three types of luting media were used: zinc phosphate cement (Elite), glass ionomer cement (Fuji I), and dual-cured composite resin cement (Panavia F). Ten copings were cemented with each type. Two master dies were used for each group, and each of them was used to lute five copings. All groups were cemented according to manufacturer's instructions and received a static load of 5 kg during cementation. After 24 hours of distilled water storage at 37 degrees C, the copings were vertically compressed using a universal testing machine at a crosshead speed of 1 mm/min. RESULTS: ANOVA revealed significant differences in the load at fracture among the three groups (p < 0.001). The fracture strength results showed that the mean fracture strength of zinc phosphate cement (Elite), glass ionomer cement (Fuji I), and resin luting cement (Panavia F) were 1091.9 N, 784.8 N, and 1953.5 N, respectively. CONCLUSION: Different luting agents have an influence on the fracture resistance of Procera AllCeram copings.