[Glide path management of rotary nickel-titanium instruments in simulated root canals].

OBJECTIVE: To compare the shaping ability of ProGlider, HyFlex EDM Glidepath File and RaCe ISO 10 with that of PathFile and stainless steel K-file hand instruments in simulated root canals. METHODS: A total of 60 simulated resin blocks were divided randomly into five groups (n=12), each group prepared with each instrument, respectively. Preparation time was recorded. Pre- and post-operative images were obtained using a scanner and superimposed using Photoshop. The material removal from the inner and outer canal walls beginning from 0 mm at the end point of the canal were measured using ImageJ. Centering ability was determined, accordingly. The data were analyzed using the One-Way ANOVA at a significance level of P<0.05. RESULTS: Preparation time for ProGlider was (61.018±5.020) s, significantly the fastest (P < 0.05), that for SS K-file (111.100±6.987) s, the slowest (P<0.05), and the differences among the other 3 groups were not significant (P>0.05). The removal of resin from the outer wall at the apical portion was significantly lower for HyFlex EDM Glidepath File than for ProGlider (P<0.05), both of them were significantly lower than the other 3 groups (P<0.05). For the removal from the inner wall at the curvature portion, ProGlider was the least whilst SS K-file the most (P<0.05). At the straight portion, RaCe ISO 10 removed the most not only from the inner but also the outer wall (P<0.05), HyFlex EDM Glidepath File the second most, and the other 3 groups among the same levels. As far as the centering ability was concerned, at the apical portion, HyFlex EDM Glidepath File was the best, ProGlider the second best, no significant difference identified among the other 3 groups. At the curvature portion, ProGlider and HyFlex EDM Glidepath File were the best, PathFile the second, RaCe ISO 10 the third, the worst was the SS K-file. At the straight portion, the difference amongt the 5 groups was not significant. CONCLUSION: The shaping abilities of ProGlider, HyFlex EDM Glidepath File and RaCe ISO 10 were better or comparable to that of PathFile, while the preparation time for ProGlider reduced significantly, and HyFlex EDM Glidepath File and RaCe ISO 10 removed significantly more resin at the straight portion of the canal.

[Effects of different techniques on removal of vapor lock in the apical region of curved canals: a cone-beam computed tomography study].

OBJECTIVE: To compare the effect of four different techniques on removal of vapor lock in the apical region of curved root canals. METHODS: Forty simulated resin root canals with 45° curvature were prepared using WaveOne Primary, then the apical foramen were sealed with soft wax. The teeth were divided randomly into 4 groups thereafter (n=10). Contract solution was injected into the canals using a 30 G side-vented needle and scanned with cone-beam CT (CBCT) to identify the volume of the vapor lock. Four different techniques including photon-induced photoacoustic streaming (PIPS) laser-activated irrigation, gutta-percha cone technique, ultrasonic irrigation, and sonic irrigation were used to remove the vapor locks in the root canals. The residual volume of the vapor lock was identified again using CBCT scanning data. Accordingly, the reduction rates of the vapor lock were calculated. Furthermore, the initial and residual vapor lock length was calculated. The data were analyzed by using the One-way ANOVA analysis and Kruskal-Wallis H test at a significance level of P<0.05. RESULTS: There was no significant difference in the initial vapor lock volume (P>0.05). Residual volume of the vapor lock for PIPS laser-activated irrigation was 0 mm(3), and that for gutta-percha cone technique was (0.02±0.07) mm3, significantly lower than those of ultrasonic and sonic irrigation, the values being (0.20±0.09) mm(3) and (0.23±0.06) mm(3) (P<0.001), respectively. The reduction rates of the vapor lock of PIPS laser-activated irrigation and gutta-percha cone technique were 100.00% (100.00%, 100.00%) and 100.00% (77.66%, 100.00%), respectively, significantly higher than those of ultrasonic irrigation [70.37% (56.41%, 91.43%)] and sonic irrigation [63.54% (51.47%, 74.00%), P<0.001]. The length of the residual vapor lock for PIPS laser-activated irrigation was 0 mm, and that for gutta-percha cone technique was (0.15±0.47) mm, significantly lower than those of ultrasonic and sonic irrigation, values being (2.21±0.09) mm and (2.34±0.08) mm (P<0.001), respectively. The length of the residual vapor locks in the ultrasonic and sonic group remained approximately the same as the distance between the working tip and the apical foramen. CONCLUSION: PIPS laser activated irrigation and gutta-percha cone technique could remove the vapor lock from the apical region of curved canals effectively.

Effect of transmembrane Ca2+ gradient on Gs function.

Gs and adenylate cyclase from bovine brain cortices were co-reconstituted into asolectin liposomes with or without 1000-fold transmembrane Ca2+ gradient. Obtained results showed that Gs activities of both binding GTP gamma S and stimulating adenylate cyclase were the highest in proteoliposomes, with a transmembrane Ca2+ gradient similar to the physiological situation and the lowest while the transmembrane Ca2+ gradient was in the inverse direction. Such a difference could be diminished following the dissipation of the transmembrane Ca2+ gradient by A23187. Time-resolved fluorescence anisotropy of diphenylhexatriene (DPH) has been used to compare the physical state of phospholipids among those proteoliposomes. It is suggested that a proper transmembrane Ca2+ gradient is essential for higher membrane fluidity, which may favor Gs function with higher GTP-binding activity and stimulation of adenylate cyclase.