Different Polymers for the Base of Removable Dentures? Part II: A Narrative Review of the Dynamics of Microbial Plaque Formation on Dentures.

This review focuses on the current disparities and gaps in research on the characteristics of the oral ecosystem of denture wearers, making a unique contribution to the literature on this topic. We aimed to synthesize the literature on the state of current knowledge concerning the biological behavior of the different polymers used in prosthetics. Whichever polymer is used in the composition of the prosthetic base (poly methyl methacrylate acrylic (PMMA), polyamide (PA), or polyether ether ketone (PEEK)), the simple presence of a removable prosthesis in the oral cavity can disturb the balance of the oral microbiota. This phenomenon is aggravated by poor oral hygiene, resulting in an increased microbial load coupled with the reduced salivation that is associated with older patients. In 15-70% of patients, this imbalance leads to the appearance of inflammation under the prosthesis (denture stomatitis, DS). DS is dependent on the equilibrium-as well as on the reciprocal, fragile, and constantly dynamic conditions-between the host and the microbiome in the oral cavity. Several local and general parameters contribute to this balance. Locally, the formation of microbial plaque on dentures (DMP) depends on the phenomena of adhesion, aggregation, and accumulation of microorganisms. To limit DMP, apart from oral and lifestyle hygiene, the prosthesis must be polished and regularly immersed in a disinfectant bath. It can also be covered with an insulating coating. In the long term, relining and maintenance of the prosthesis must also be established to control microbial proliferation. On the other hand, several general conditions specific to the host (aging; heredity; allergies; diseases such as diabetes mellitus or cardiovascular, respiratory, or digestive diseases; and immunodeficiencies) can make the management of DS difficult. Thus, the second part of this review addresses the complexity of the management of DMP depending on the polymer used. The methodology followed in this review comprised the formulation of a search strategy, definition of the inclusion and exclusion criteria, and selection of studies for analysis. The PubMed database was searched independently for pertinent studies. A total of 213 titles were retrieved from the electronic databases, and after applying the exclusion criteria, we selected 84 articles on the possible microbial interactions between the prosthesis and the oral environment, with a particular emphasis on Candida albicans.

Relationships between bone mass and micro-architecture at the mandible and iliac bone in edentulous subjects: a dual X-ray absorptiometry, computerised tomography and microcomputed tomography study.

OBJECTIVES: To compare bone volume, bone mineral density, cortical thickness and bone micro-architecture in a series of paired mandibular and iliac bone samples analysed by various imagery techniques to see whether relationships exist between the various techniques and between mandibular and iliac bone. MATERIALS AND METHODS: Bone samples from the mandible and ilium were harvested in 20 cadavers and analysed by dual energy X-ray absorptiometry (DXA), computerised tomography (CT) on a conventional hospital machine and microCT. RESULTS: Significant correlations were found between Hounsfield density obtained by CT, and bone mass determined by microCT but not with DXA values. Cortical thickness measurements were well correlated between CT and microCT. No relationships were found between mandibular and iliac bone, when considering mineral density, cortical thickness, bone volume or micro-architecture. CONCLUSION: In clinical practice, CT remains the most appropriate routine means for bone qualitative and quantitative evaluation at the mandible. In this ex vivo study, these results confirm that mandibular bone status does not reflect the axial skeletal one and assist in the placement of implants with dental prostheses in old or osteoporotic patients.

Bone loss and teeth.

Loss of teeth results in irreversible alveolar bone resorption, and untreated dental disease causes alveolar bone lysis that ultimately leads to loss of teeth. In addition to anchoring the teeth in the alveolar ridge, the maxillary and mandibular bone allows dental restoration procedures, such as construction of root-supported implants, fixed dentures, or removable dentures. However, the functional and cosmetic results depend on the quantity and quality of the maxillary or mandibular bone, which can be affected by many normal and abnormal processes. The alveoli are particularly fragile and labile. Changes in alveolar bone vary considerably across individuals and depend directly on local factors. Many studies have investigated associations between alveolar bone status and bone mass at other skeletal sites. These studies focused chiefly on the course of parodontal disease, alveolar ridge resorption after tooth extraction, and density differences across various mandibular sites. They produced conflicting results, probably because of differences in measurement methods. Measurement sites and methods should be standardized to ensure that reliable and comparable data are obtained. To date, there are few reliable methods for obtaining quantitative measurements of bone mineral content in maxillary and mandibular bone.

[Non-invasive evaluation of an injectable bone substitute]. / Méthods non invasive d'évaluation d'un substitut osseux injectable.

Despite the increasing number of techniques for the preservation of bone ridges after dental avulsion, no precise evaluation of alveolar filling has been performed to date. The criteria of available measurement techniques (probes, retroalveolar or panoramic radiography, and lateral teleradiography) are not sufficiently reliable and precise. This study investigated the reliability of evaluation based on CT images in comparison with retroalveolar radiography (the most precise radiographic technique, providing standardised images), direct measurements, and images obtained in scanning electron microscopy. After a preliminary investigation ex vivo, a study was performed in vivo on three beagles. Mandibular premolars were extracted, and the corresponding alveoli were filled with an injectable bone substitute composed of a calcium phosphate mineral load associated with hydroxypropyl methylcellulose. Measurements performed on CT images relative to visual and automatic detection of density changes and studies of density curves provided better precision than those obtained by retroalveolar radiography.