Wearable Flexible Strain Sensor Based on Three-Dimensional Wavy Laser-Induced Graphene and Silicone Rubber.

Laser-induced graphene (LIG) has the advantages of one-step fabrication, prominent mechanical performance, as well as high conductivity; it acts as the ideal material to fabricate flexible strain sensors. In this study, a wearable flexible strain sensor consisting of three-dimensional (3D) wavy LIG and silicone rubber was reported. With a laser to scan on a polyimide film, 3D wavy LIG could be synthesized on the wavy surface of a mold. The wavy-LIG strain sensor was developed by transferring LIG to silicone rubber substrate and then packaging. For stress concentration, the ultimate strain primarily took place in the troughs of wavy LIG, resulting in higher sensitivity and less damage to LIG during stretching. As a result, the wavy-LIG strain sensor achieved high sensitivity (gauge factor was 37.8 in a range from 0% to 31.8%, better than the planar-LIG sensor), low hysteresis (1.39%) and wide working range (from 0% to 47.7%). The wavy-LIG strain sensor had a stable and rapid dynamic response; its reversibility and repeatability were demonstrated. After 5000 cycles, the signal peak varied by only 2.32%, demonstrating the long-term durability. Besides, its applications in detecting facial skin expansion, muscle movement, and joint movement, were discussed. It is considered a simple, efficient, and low-cost method to fabricate a flexible strain sensor with high sensitivity and structural robustness. Furthermore, the wavy-LIG strain senor can be developed into wearable sensing devices for virtual/augmented reality or electronic skin.

Fabrication of bioinspired grid-crimp micropatterns by melt electrospinning writing for bone-ligament interface study.

Many strategies have been adopted to engineer bone-ligament interface, which is of great value to both the tissue regeneration and the mechanism understanding underlying interface regeneration. However, how to recapitulate the complexity and heterogeneity of the native bone-ligament interface including the structural, cellular and mechanical gradients is still challenging. In this work, a bioinspired grid-crimp micropattern fabricated by melt electrospinning writing (MEW) was proposed to mimic the native structure of bone-ligament interface. The printing strategy of crimped fiber micropattern was developed and the processing parameters were optimized, which were used to mimic the crimp structure of the collagen fibrils in ligament. The guidance effect of the crimp angle and fiber spacing on the orientation of fibroblasts was studied, and both of them showed different levels of cell alignment effect. MEW grid micropatterns with different fiber spacings were fabricated as bone region. Both the alkaline phosphatase activity and calcium mineralization results demonstrated the higher osteoinductive ability of the MEW grid structures, especially for that with smaller fiber spacing. The combined grid-crimp micropatterns were applied for the co-culture of fibroblasts and osteoblasts. The results showed that more cells were observed to migrate into the in-between interface region for the pattern with smaller fiber spacing, suggested the faster migration speed of cells. Finally, a cylindrical triphasic scaffold was successfully generated by rolling the grid-crimp micropatterns up, showing both structural and mechanical similarity to the native bone-ligament interface. In summary, the proposed strategy is reliable to fabricate grid-crimp triphasic micropatterns with controllable structural parameters to mimic the native bone-to-ligament structure, and the generated 3D scaffold shows great potential for the further bone-ligament interface tissue engineering.

Fabrication and in vitro evaluation of PCL/gelatin hierarchical scaffolds based on melt electrospinning writing and solution electrospinning for bone regeneration.

As an emerging 3D printing technique, melt electrospinning writing (MEW) has been used to fabricate scaffolds with controllable structure and good mechanical strength for bone regeneration. However, how to further improve MEW scaffolds with nanoscale extracellular matrix (ECM) mimic structure and bioactivity is still challenging. In this study, we proposed a simple composite process by combining MEW and solution electrospinning (SE) to fabricate a micro/nano hierarchical scaffold for bone tissue engineering. The morphological results confirmed the hierarchical structure with both well-defined MEW microfibrous grid structure and SE random nanofiber morphology. The addition of gelatin nanofibers turned the scaffolds to be hydrophilic, and led to a slight enhancement of mechanical strength. Compared with PCL MEW scaffolds, higher cell adhesion efficiency, improved cell proliferation and higher osteoinductive ability were achieved for the MEW/SE composite scaffolds. Finally, multilayer composite scaffolds were fabricated by alternately stacking of MEW layer and SE layer and used to assess the effect on cell ingrowth in the scaffolds. The results showed that gelatin nanofibers did not inhibit cell penetration, but promoted the three-dimensional growth of bone cells. Thus, the strategy of the combined use of MEW and SE is a potential method to fabricate micro/nano hierarchical scaffolds to improve bone regeneration.

Melt electrohydrodynamic 3D printed poly (ε-caprolactone)/polyethylene glycol/roxithromycin scaffold as a potential anti-infective implant in bone repair.

Implanted scaffold or bone substitute is a common method to treat bone defects. However, the possible bone infection caused by orthopaedic surgery has created a challenging clinical problem and generally invalidate bone repair and regeneration. In this study, a poly (ε-caprolactone) (PCL)/polyethylene glycol (PEG)/roxithromycin (ROX) composite scaffold was prepared via melt electrohydrodynamic (EHD) 3D printing. Fourier transform infrared spectroscopy (FTIR) spectroscopy was performed to verify the existence of PEG and ROX in the scaffolds. By water contact angle measurement, the addition of both PEG and ROX was found to improve the hydrophilicity of the scaffolds. By in vitro drug release assay, the PCL/PEG/ROX scaffolds showed an initial burst drug release and subsequent long-term sustained release behaviour, which is favourable for the prevention and treatment of bone infections. The antibacterial assays against E. coli and S. aureus demonstrated that the composite scaffold with ROX possessed effective antibacterial activity, especially for S. aureus, the main cause of bone infection. The immunostaining and MTT assay with human osteoblast-like cells (MG63) indicated that cells showed good viability and growth on the scaffolds. Therefore, the melt EHD 3D printed PCL/PEG/ROX scaffold could be a promising anti-infective implant for bone tissue engineering.

Automatic quantitative analysis of ore content of human tooth enamel based on image processing.

Introducing the theory of fuzzy set, mathematical morphology and computerized mask fast scanning, we developed the TOOTH.SCA software and method to analyze the effect of fluoride (NaF) on ore content of human tooth enamel automatically and quantitatively. And we obtained some characteristic parameters, such as the depth, the type and the demineralized content of every scathing layer of dental caries. The smallest scale of mask scanning is 0.1 microm x 0.1 microm and the time required to analyze a sample is only 12 s. The applied software and method we built play an important role to the research on the mechanism of pathological changes of teeth and preventing dental caries.