Clinical validation of a saliva-based matrix metalloproteinase-1 rapid strip test for detection of oral cavity cancer.

BACKGROUND: We previously identified matrix metalloproteinase-1 (MMP-1) as one of the most promising salivary biomarkers for oral squamous cell carcinoma (OSCC) and developed a sensitive ELISA for MMP-1 with good performance in detection of OSCC using a cohort of 1160 saliva samples. METHODS: A time-saving rapid strip test (RST) for MMP-1 was developed in this study and its diagnostic performance compared with ELISA using saliva samples from a new cohort of 603 subjects (171 healthy controls, 236 patients with oral potentially malignant disorders, and 196 OSCC patients). RESULTS: Salivary MMP-1 levels measured using RST and ELISA were highly comparable and both assays could effectively distinguish between OSCC and non-cancerous groups. Similar to ELISA, receiver operating characteristic curve analysis of the MMP-1 RST was effective in identifying patients with OSCC at different oral cavity sites and stages. CONCLUSIONS: Salivary MMP-1 can be sensitively detected using both RST and ELISA methods. Our newly developed point-of-care MMP-1 RST is a promising in vitro diagnostic device (IVD) that may serve as a novel auxiliary tool in the routine clinical detection and monitoring of OSCC.

Effects of varying material properties on the load deformation characteristics of heel cushions.

Various insole materials were used in attenuation of heel-strike impact. This study presented a compression test to investigate the deformation characteristics of common heel cushions. There were two materials (thermoplastic elastomer "TPE" and silicone) with three hardness and six thickness being analyzed. They underwent consecutive loading-unloading cycles with a load control mode. The displacement of material thickness was recorded during cyclic compression being applied and released from 0 to 1050 N. The energy input, return and dissipation were evaluated based on the load deformation curves when new and after repeated compression. The TPE recovered more deformed energy and thickness than the silicone after the first loading cycle. The silicone would preserve more strain energy with increasing its hardness for the elastic recovery in the unloading process. The deformed energy was decreased as the original thickness did not completely recover under cyclic tests. The reduction in hysteresis area was gradually converged within 20 cycles. The silicone attenuated more impact energy in the initial cycles, but its energy dissipation was reduced after repeated loading. To increase hardness or thickness should be considered to improve resilience or accommodate persistent compression without flattening. The careful selection of cushion materials is imperative to meet individual functional demands.

Polyvinylidene fluoride/siloxane nanofibrous membranes for long-term continuous CO2 -capture with large absorption-flux enhancement.

In a CO2 membrane contactor system, CO2 passes through a hydrophobic porous membrane in the gas phase to contact the amine absorbent in the liquid phase. Consequently, additional CO2 gas is absorbed by amine absorbents. This study examines highly porous polyvinylidene fluoride (PVDF)/siloxane nanofibrous layers that are modified with hydrophobic fluoroalkylsilane (FAS) functional groups and successfully coated onto a macroporous Al2 O3 membrane. The performance of these materials in a membrane contactor system for CO2 absorption is also investigated. Compared with pristine PVDF nanofibrous membranes, the PVDF/siloxane nanofibrous membranes exhibit greater solvent resistance and mechanical strength, making them more suitable for use in CO2 capture by the membrane contactor. The PVDF/siloxane nanofibrous layer in highly porous FAS-modified membranes can prevent the wetting of the membrane by the amine absorbent; this extends the periods of continuous CO2 absorption and results in a high CO2 absorption flux with a minimum of 500 % enhancement over that of the uncoated membranes. This study suggests the potential use of an FAS-modified PVDF/siloxane nanofibrous membrane in a membrane contactor system for CO2 absorption. The resulting hydrophobic membrane contactor also demonstrates the potential for large-scale CO2 absorption during post-combustion processes in power plants.

Mesoporous fluorocarbon-modified silica aerogel membranes enabling long-term continuous CO2 capture with large absorption flux enhancements.

The use of a membrane contactor combined with a hydrophobic porous membrane and an amine absorbent has attracted considerable attention for the capture of CO2 because of its extensive use, low operational costs, and low energy consumption. The hydrophobic porous membrane interface prevents the passage of the amine absorbent but allows the penetration of CO2 molecules that are captured by the amine absorbent. Herein, highly porous SiO2 aerogels modified with hydrophobic fluorocarbon functional groups (CF3 ) were successfully coated onto a macroporous Al2 O3 membrane; their performance in a membrane contactor for CO2 absorption is discussed. The SiO2 aerogel membrane modified with CF3 functional groups exhibits the highest CO2 absorption flux and can be continuously operated for CO2 absorption for extended periods of time. This study suggests that a SiO2 aerogel membrane modified with CF3 functional groups could potentially be used in a membrane contactor for CO2 absorption. Also, the resulting hydrophobic SiO2 aerogel membrane contactor is a promising technology for large-scale CO2 absorption during the post-combustion process in power plants.