Comparison of air-sealing characteristics of tapered- vs. cylindrical-shaped high-volume, low-pressure tube cuffs.

BACKGROUND: This study aimed at comparing air-sealing characteristics of the new tapered-shaped tracheal tube cuffs with cylindrical tube cuffs. METHODS: Tracheal tubes with tapered-shaped polyurethane (PU) and polyvinyl chloride (PVC) cuffs as well as standard cylindrical-shaped cuffs made of PU and PVC (Covidien, Athlone, Ireland) were investigated. A tracheal model attached to a test lung was intubated, and cuffs were inflated to 10, 15, 20, 25 and 30 cm H(2)O. The test lung was ventilated with intermittent positive pressure ventilation at peak inspiratory pressures (PIPs) of 20 and 25 cm H(2)O. Air leakage was assessed by spirometry and measurement of sevoflurane concentration passing the cuff at the upper cuff border using an anaesthetic gas analyser. Experiments were repeated four times with new tracheal tubes for each run. Statistical comparisons were done using Mann-Whitney U-test with level of significance at P < 0.05. RESULTS: The tapered-shaped PVC tube cuff demonstrated a significantly lower air leakage determined by spirometry than the cylindrical-shaped cuff at both PIPs (20 and 25 cm H(2)O). Similarly, sevoflurane leakage was less with the tapered PVC cuff particularly at higher cuff pressures. With the PU cuff, reduction in air leakage by a tapered-shaped compared with a cylindrical-shaped tube cuff was not significant. CONCLUSIONS: A tapered-shaped tube cuff considerably improves air-sealing characteristics of PVC tube cuffs and allows thereby reducing cuff pressure required for sufficient ventilation. In tube cuffs made of PU that exhibits superior sealing characteristics compared with PVC, a tapered shape failed to result in a further reduction of air leakage.

Effect of tracheal tube cuff shape on fluid leakage across the cuff: an in vitro study.

BACKGROUND: This study compared the fluid leakage in the new 'tapered' shaped against the classic 'cylindrical' shaped tracheal tube cuffs when placed in different sized tracheas. METHODS: The 7.5 mm internal diameter (ID) tracheal tube cuffs-Tapered Seal Guard (TSG), Standard Seal Guard (SSG), Hi-Lo, Microcuff, Ruesch, and Portex Profile-were compared in an in vitro apparatus. Vertical artificial tracheas with 16, 20, and 22 mm ID were intubated, 5 ml clear water was applied above the unlubricated tube cuffs, and fluid leakage was measured up to 60 min. Data of tapered vs non-tapered tube cuffs (16 observations) were compared for each tracheal diameter using the Mann-Whitney test. RESULTS: Median (range) fluid leakage (ml) at 60 min was 2.14 (0.05-4.88), 1.14 (0.00-4.84), and 0.13 (0.00-1.32), respectively, for 16, 20, and 22 mm tracheas in the TSG tube studies when compared with 4.58 (0.44-4.88), 2.21 (0.00-4.81), and 0.00 (0.00-4.81) in the SSG tube and 4.54 (1.54-4.82), 0.90 (0.00-4.49), and 4.85 (4.40-4.99) in the Microcuff tube studies. Leakage in all polyvinylchloride (PVC) tube cuffs was almost complete (5 ml) within 5 min (P<0.001). CONCLUSIONS: The tapered PU tube cuff was as effective as the cylindrical PU cuffs in smaller tracheal diameters and was more efficient than the cylindrical Microcuff PU tube cuff in larger tracheal diameter in preventing subglottic fluid leakage across the tube cuff tested in this in vitro study. PVC tube cuffs leaked much more and faster than PU cuffs.

The use of localised CBCT to image inflammatory collateral cysts: a retrospective case series demonstrating clinical and radiographic features.

INTRODUCTION: Inflammatory collateral cysts are uncommon cysts primarily affecting first permanent molars during their eruption. There are diagnostic challenges that can be overcome with CBCT imaging. However, given the paediatric age group for this condition, there are patient cooperation and radiation dose factors to consider when justifying the scan. The aim of this case series study is to illustrate the value of CBCT in imaging and diagnosing inflammatory collateral cysts in paediatric patients, to highlight the need for a multidisciplinary approach for this uncommon pathological condition and to review the relevant literature. CASE SERIES DESCRIPTION AND RESULTS: We present three patients aged between 6 and 11 years of age with inflammatory collateral cysts affecting their first or second permanent molars for which CBCT imaging was utilised. All patients underwent cyst enucleation with preservation or extraction of affected teeth under general anaesthesia. DISCUSSION: Inflammatory collateral cysts are likely to be under reported given their indistinct clinical features and radiological signs. Conventional planar radiographs may not reveal this lesions size and full extent. CBCT overcomes these limitations; however, careful assessment of patient cooperation is needed and a low-dose protocol should be used. CONCLUSIONS: CBCT can provide useful imaging information which is difficult to obtain using conventional radiography, especially in cases where an inflammatory collateral cyst is suspected.

Correction to: Diagnostic efficacy of cone beam computed tomography in paediatric dentistry: a systematic review.

In the original publication of the article the fifth author's name "A. Littlewood" was submitted as "A. Littewood" which was left unnoticed in the later stages. The correct name is as published in this erratum.

Diagnostic efficacy of cone beam computed tomography in paediatric dentistry: a systematic review.

PURPOSE: To determine in which clinical situations it is indicated or contra-indicated to prescribe cone beam computed tomography (CBCT) for paediatric patients. METHODS: Systematic review of in vivo paediatric research studies of diagnostic efficacy using CBCT, with supplementary searches for guideline documents on CBCT and for systematic reviews permitting inclusion of ex vivo and adult studies. RESULTS: After screening, 190 publications were included, mostly case studies. No systematic reviews were found of in vivo paediatric research. Fourteen studies of diagnostic efficacy were identified. The supplementary searches found 18 guideline documents relevant to the review and 26 systematic reviews. The diagnostic efficacy evidence on CBCT was diverse and often of limited quality. There was ex vivo evidence for diagnostic accuracy being greater using CBCT than radiographs for root fractures. The multiplanar capabilities of CBCT are advantageous when localising dental structures for surgical planning. Patient movement during scanning is more common in children which could reduce diagnostic efficacy. CONCLUSIONS: No strong recommendations on CBCT are possible, except that it should not be used as a primary diagnostic tool for caries. Guidelines on use of CBCT in the paediatric age group should be developed cautiously, taking into account the greater radiation risk and the higher economic costs compared with radiography. CBCT should only be used when adequate conventional radiographic examination has not answered the question for which imaging was required. Clinical research in paediatric patients is required at the higher levels of diagnostic efficacy of CBCT.

Challenges in X-ray diagnosis: a review of referrals for specialist opinion.

The aim of this study was to determine the common reasons why a dental professional might request a second opinion on a dental radiograph from a Dental and Maxillofacial (DMF) radiologist. The study was a retrospective analysis of consecutive referrals for an opinion received by post or email by one DMF radiologist based in a UK dental hospital. The study period was from March 2009 to November 2015. Referrals came from a mixture of sources: mainly from general dental practitioners and specialists working in primary care, but with some referrals from hospital-based practitioners. An enormous range in diagnoses were made by the DMF radiologist, but the ten most frequent diagnostic categories contributed 57.5% of the total. Normal anatomy and anatomical variations in normal anatomy made up the largest category. Common dental disease was often diagnosed, but idiopathic osteosclerosis and maxillary antrum pathosis were both frequent reasons for seeking a second opinion. This service evaluation may assist in developing curricula for undergraduates and in designing continuing education courses. It also highlights a service that may avoid unnecessary referrals to hospital specialists but which currently is not commissioned by the NHS.

The use of alkanethiol self-assembled monolayers on 316L stainless steel for coronary artery stent nanomedicine applications: an oxidative and in vitro stability study.

The use of self-assembled monolayers (SAMs) on medical devices offers a methodology for the incorporation of nanotechnology into medicine. SAMs are highly ordered nanosized molecular coatings, adding 1 to 10 nm thickness to a surface. This work is part of an overall goal to deliver therapeutic drugs from the surface of metal coronary stents using SAMs. In this study the oxidative and in vitro stability of functional alkylthiol SAMs on 316L stainless steel (SS) has been demonstrated. SAMs of 11-mercaptoundecanoic acid (-COOH SAM) and 11-mercapto-1-undecanol (-OH SAM) were formed on 316L SS. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and contact angle (CA) measurements collectively confirmed the formation of functional alkylthiol SAMs on 316L SS. Well-formed SAMs (CA: 82 deg +/- 9 deg) were achieved within 48 hours of immersion in ethanolic solutions, after which no significant improvement in CA was observed. The ratio of the thiolate peak (163.5 eV) to the oxidized sulfur (sulfonates) peak (166.5 eV) gives us an indication of the percentage SAMs that would bind to the metal and serve as a drug reservoir in vivo; which in turn represents the stability and viability of these SAMs, keeping in mind the cardiovascular application under consideration. Oxidative and in vitro stability studies showed that alkanethiol SAMs oxidized completely within 14 days. The SAMs tend to desorb and leave the metal surface after longer time periods (21 days) in phosphate-buffered saline (PBS) immersion, whereas for oxidative exposure the SAMs continue to remain on the metal surface in the form of sulfonates. Although the chemistry of bonding of alkylthiol with the 316L SS is not well understood, the nanosized alkylthiol SAMs demonstrate sufficient stability to justify further study on these systems for potential in vivo drug delivery in the chosen coronary artery stent applications.

Closed tracheal suction and fluid aspiration past the tracheal tube. Impact of tube cuff and airway pressure.

BACKGROUND: This study investigated the effect of different tube cuff types and airway pressures on fluid leakage past the tracheal tube cuff during suction with a closed tracheal suction system (CTSS). METHODS: Unlubricated high-volume, low-pressure tracheal tube cuffs made from polyvinylchloride (PVC) and polyurethane (PU) with a size 7.5 mm internal diameter (ID) were placed in a 22 mm ID artificial trachea connected to a test lung and inflated to 25 or 50 cmH2O of cuff pressure. Positive pressure ventilation (PPV) with peak inspiratory pressures of 15, 20 or 25 cmH2O and positive end expiratory pressures (PEEP) of 5 or 10 cmH2O were used. A CTSS catheter (14 Fr) was attached to the tracheal tube and suction was performed for 5, 10, 15 or 20 s with 200 or 300 cmH2O of negative suction pressures. The volume of fluid leaking across the tube cuff at the end of the suction procedure was measured (mL), and the airway pressure was simultaneously recorded. Fluid leakage and airway pressures during different suction conditions were compared using a Kruskal Wallis test and Mann Whitney test (P<0.05). RESULTS: The airway pressure drop during suction was similar for both tube cuffs. The PU tube cuff resulted in significantly less fluid leakage (range 0.00-0.12 mL) than the PVC tube cuff (P<0.001). For the PVC tube cuff, fluid leakage at higher cuff pressures was significantly less (P<0.01).Varying PEEP and PIP did not change the fluid leakage or the drop in airway pressure. CONCLUSION: The use of PU tube cuffs and intermittent transient increases in cuff pressure during suction can effectively reduce fluid leakage past the tracheal tube during closed tracheal suctioning.

Drug delivery from therapeutic self-assembled monolayers (T-SAMs) on 316L stainless steel.

Delivery of therapeutic agents from self-assembled monolayers (SAMs) on 316L stainless steel (SS) has been demonstrated as a viable method to deliver drugs for localized coronary artery stent application. SAMs are highly-ordered, nano-sized molecular coatings, adding 1-10 nm thickness to a surface. Hydroxyl terminated alkanethiol SAMs of 11-mercapto-1-undecanol (-OH SAM) were formed on 316L SS with 48 hr immersion in ethanolic solutions. Attachment of ibuprofen (a model drug) to the functional SAMs was carried out in toluene for 5 hrs at 60 degrees C using Novozume-435 as a biocatalyst. SAM formation and subsequent attachment of ibuprofen was characterized collectively using X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and contact angle (CA) measure-ments. The quantitative in vitro release of ibuprofen into a "physiological" buffer solution was characterized using reverse phase HPLC. Drug release kinetics showed that 14.1 microg of ibuprofen eluted over a period of 35 days with 2.7microg being eluted in the first day and the remaining being eluted over a period of 35 days. The drug release kinetics showed an increase in ibuprofen elution that occurred during first 14 days (2.7microg in 1 day to 9.5 microg in 14 days), following which there was a decrease in the rate of elution. Thus, functional SAMs on 316L SS could be used as tethers for drug attachment and could serve as a drug delivery mechanism from stainless steel implants such as coronary artery stents.

Drug delivery from gold and titanium surfaces using self-assembled monolayers.

Currently available drug-eluting stents (DES) use polymers for coating and releasing drugs. Increasing evidence suggests that inflammatory and hypersensitive reactions are caused by such polymer coatings. This study focused on developing new techniques for delivering drugs directly from metal implant surfaces. Hydroxyl-terminated self-assembled monolayers (SAMs) were coated on Au and Ti surfaces. Therapeutic self-assembled monolayers (TSAMs) were prepared by chemically attaching the model drug, flufenamic acid, to SAM coated metal surfaces. Three different methods of esterification (acid chloride esterification, dry heat esterification, and direct esterification) were explored to attach flufenamic acid to SAMs. TSAMs were characterized using X-ray photoelectron spectroscopy, fluorescence microscopy, atomic force microscopy, and contact angle goniometry. These techniques collectively confirmed the attachment of drug onto SAM coated metal surfaces. In vitro drug release was investigated by immersing TSAM coated metal specimens in tris-buffered saline (TBS) at 37 degrees C for 28 days. TBS was analyzed at 1, 3, 7, 14, 21, and 28 days for the amount of drug eluted using high performance liquid chromatography. Large data scatter was observed for the release profiles of TSAMs prepared by acid chloride esterification. TSAMs prepared by dry heat and direct esterification methods showed an initial burst release of the drug followed by a sustained slow release for up to 2 weeks. Thus, this study suggests the potential for using self-assembled monolayers as an alternate system for delivering drugs from coronary stents and other metal implants.

Thiocyanate as a marker of saliva in gastric juice?

One source of error in gastric secretion studies is swallowed saliva. The possibility that salivary thiocyanate might be used to measure this contamination has been investigated. Thiocyanate concentration was measured in saliva and gastric juice collected simultaneously in 22 duodenal ulcer patients undergoing routine insulin and histamine secretion studies. On stimulation, despite the increase in the rate of gastric secretion this was not matched by an appropriate fall in the concentration of thiocyanate in gastric juice. Moreover, in one-third of the gastric juice specimens, the thiocyanate concentration was greater than in the simultaneous samples of saliva. Thus, contrary to what has been claimed, thiocyanate is present not only in saliva but also in gastric juice. Therefore it cannot be used as a marker of salivary contamination. An adequate marker of this source of error has not yet been found.