Poly(malic acid) production from liquefied corn starch by simultaneous saccharification and fermentation with a novel isolated Aureobasidium pullulans GXL-1 strain and its techno-economic analysis.

In this study, a novel Aureobasidium pullulans GXL-1 strain without melanin secretion was isolated for efficient polymalic acid (PMA) production. The PMA produced by GXL-1 was characterized, and its molecular mass was determined to be 1.621 kDa by gel permeation chromatography. Liquefied corn starch was shown to replace glucose for PMA production by GXL-1 through simultaneous saccharification and fermentation. The PMA titer obtained from batch fermentation was up to 49.0 ± 1.6 g/L in a 10 L fermentor, and the PMA yield and productivity obtained from repeated-batch fermentation were up to 0.50 g/g and 0.34 g/L·h, respectively. Furthermore, process design and techno-economic analysis were performed at an annual output level of 5000 metric tons by SuperPro Designer. Results showed that the production cost of $2.046/kg and payback period of 6.9 years were achieved by repeated-batch fermentation; this provides an economically feasible strategy for industrial-scale production of PMA.

Selective removal and persulfate catalytic decomposition of diethyl phthalate from contaminated water on modified MIL100 through surface molecular imprinting.

Adsorptive removal of phthalate esters from wastewater combined with their persulfate (PS) catalytic degradation has attracted the attention of many researchers. In this study, the adsorptive and catalytic properties of an MIL100 material obtained by a green synthetic route have been optimized by a surface molecular imprinting technique. Results have shown that there are two steps in the molecular imprinting process. A polymerization is first carried out in the internal channels of the material and the imprinting layer is then formed on the surface. The relative proportions of the starting materials for the synthesis have been optimized through the design of a three-dimensional response surface. The amount of pollutant adsorbed was increased fourfold after surface imprinting, reaching 13.6 mg g-1. The homogeneity of the recognition sites has been evaluated by dynamics calculations and the Freundlich equation. The selective adsorption ability of the material for diethyl phthalate was improved, and the process involved chemical adsorption. The catalytic properties of the material after imprinting were increased about 1.5-fold, indicating that selective adsorption is important. Such molecularly imprinted polymers may potentially serve as good functional materials for the removal of phthalate esters from wastewater.

Development and benefit evaluation of fermentation strategies for poly(malic acid) production from malt syrup by Aureobasidium melanogenum GXZ-6.

Malt syrup, as a low-cost substrate without any pretreatment, was proved to be able to replace maltose for ploymalic acid (PMA) production by Aureobasidium melanogenum GXZ-6. The PMA titer of 55.53 ±â€¯1.72 g/L was obtained by batch fermentation in a 10-L fermentor with addition of malate, citrate and sodium malonate. Then, a higher PMA titer of 124.07 ±â€¯2.28 g/L was obtained in fed-batch fermentation, which increased by 123.43% than that from batch fermentation. Moreover, repeated-batch fermentation with three batches gave a PMA titer of 64.06 g/L on average with a higher yield of 0.81 g/g and productivity of 0.56 g/L·h. Fermentation process and economics analysis were performed by SuperPro Designer for a 2000 metric tons plant. Results showed that PMA production cost was as low as $ 1.716/kg by fed-batch fermentation, which provides an economical strategy for large-scale PMA production.

Highly Stretchable Metallic Nanowire Networks Reinforced by the Underlying Randomly Distributed Elastic Polymer Nanofibers via Interfacial Adhesion Improvement.

On-skin electronics require conductive, porous, and stretchable materials for a stable operation with minimal invasiveness to the human body. However, porous elastic conductors that simultaneously achieve high conductivity, good stretchability, and durability are rare owing to the lack of proper design for good adhesion between porous elastic polymer and conductive metallic networks. Here, a simple fabrication approach for porous nanomesh-type elastic conductors is shown by designing a layer-by-layer structure of nanofibers/nanowires (NFs/NWs) via interfacial hydrogen bonding. The as-prepared conductors, consisting of Ag NWs and polyurethane (PU) NFs, simultaneously achieve high conductivity (9190 S cm-1 ), high stretchability (310%), and good durability (82% resistance increase after 1000 cycles of deformation at 70% tensile strain). The direct contact between the Ag NWs enables the high conductivity. The synergistic effect of the layer-by-layer structure and good adhesion between the Ag NWs and the PU NFs enables good mechanical properties. Furthermore, without any adhesive gel/tape, the conductors can be utilized as breathable strain sensors for precise joint motion monitoring, and as breathable sensing electrodes for continuous electrophysiological signal recording.

One-Step Fabrication of Stretchable Copper Nanowire Conductors by a Fast Photonic Sintering Technique and Its Application in Wearable Devices.

Copper nanowire (CuNW) conductors have been considered to have a promising perspective in the area of stretchable electronics due to the low price and high conductivity. However, the fabrication of CuNW conductors suffers from harsh conditions, such as high temperature, reducing atmosphere, and time-consuming transfer step. Here, a simple and rapid one-step photonic sintering technique was developed to fabricate stretchable CuNW conductors on polyurethane (PU) at room temperature in air environment. It was observed that CuNWs were instantaneously deoxidized, welded and simultaneously embedded into the soft surface of PU through the one-step photonic sintering technique, after which highly conductive network and strong adhesion between CuNWs and PU substrates were achieved. The CuNW/PU conductor with sheet resistance of 22.1 Ohm/sq and transmittance of 78% was achieved by the one-step photonic sintering technique within only 20 µs in air. Besides, the CuNW/PU conductor could remain a low sheet resistance even after 1000 cycles of stretching/releasing under 10% strain. Two flexible electronic devices, wearable sensor and glove-shaped heater, were fabricated using the stretchable CuNW/PU conductor, demonstrating that our CuNW/PU conductor could be integrated into various wearable electronic devices for applications in food, clothes, and medical supplies fields.