Label-free electrochemical immunosensor based on gold nanoparticle/polyethyleneimine/reduced graphene oxide nanocomposites for the ultrasensitive detection of cancer biomarker matrix metalloproteinase-1.

Matrix metalloproteinase-1 (MMP-1) is associated with many types of cancers, including oral, colorectal, and brain cancers. This paper describes the fabrication of an MMP-1 immunosensor based on a gold nanoparticle/polyethyleneimine/reduced graphene oxide (AuNP/PEI/rGO)-modified disposable screen-printed electrode (SPE). A microwave-assisted single-step method was employed for the simultaneous reduction of gold and graphene oxide in a PEI environment to avoid AuNP agglomeration. The crystal structure, chemical composition, optical properties, and interior morphology of the materials were probed by X-ray diffraction, Raman spectroscopy, UV-visible spectrometry, and transmission electron microscopy techniques. To assemble a label-free MMP-1 immunosensor layer-by-layer, 3-mercaptopropionic acid was utilized due to its strong sulfur-gold bonding ability, and its tail end was attached to a carboxyl group, allowing the MMP-1 antibody (anti-MMP-1) to be subsequently cross-linked using the traditional N-(3-dimethylaminopropyl) and N' ethylcarbodiimide hydrochloride method. Differential pulse voltammetry analysis showed a linear relationship with MMP-1 concentration in the range of 1-50 ng ml-1 with an R2 value of ∼0.996 (n = 5, RSD < 5%). This immunosensor was successfully applied for MMP-1 detection in urine, saliva, bovine serum, and cell culture media (HSC-3 & C6) of oral and brain cancers showing results comparable to those of the credible ELISA method.

Disposable and cost-effective label-free electrochemical immunosensor for prolactin based on bismuth sulfide nanorods with polypyrrole.

Prolactin (PRL) is produced by the pituitary gland and plays a vital role in the production of milk after a baby is born. PRL levels are normally elevated in pregnant and nursing women, and high levels of PRL in the human body cause hyperprolactinemia, infertility, galactorrhea, infrequent or irregular periods, amenorrhea, breast pain, and loss of libido. Accordingly, herein, a novel label-free immunosensor using a bismuth sulfide/polypyrrole (Bi2S3/PPy)-modified screen-printed electrode (SPE) for the fast and facile detection of the peptide hormone PRL. Bi2S3 nanorods were synthesized via a facile hydrothermal technique, and PPy was prepared by chemical polymerization method. Subsequently, the Bi2S3/PPy/ SPE was modified with 3-mercaptopropionic acid (MPA) and EDC/NHS. Owing to the cross-linking effect of EDC/NHS, antibody-PRL (anti-PRL) was firmly stabilized on the modified SPE surface. These layer-by-layer modifications enhanced the conducting properties, anti-PRL loading capacity, and sensitivity of the developed immunosensor. Under optimized conditions, the PRL immunosensor demonstrated a broad linear range of approximately 1-250 ng/mL, a low detection limit of approximately 0.130 ng/mL (3 × SD/b), good specificity, reproducibility, and stability. PRL was successfully evaluated in human and mouse serum samples, and the corresponding outcomes were compared with those of the electrochemical and ELISA methods.

An energy-harvesting scheme employing CuGaSe2 quantum dot-modified ZnO buffer layers for drastic conversion efficiency enhancement in inorganic-organic hybrid solar cells.

We demonstrated a promising route to enhance the performance of inverted organic photovoltaic (OPV) devices by the incorporation of CuGaSe2 (CGS) quantum dots (QDs) into the ZnO buffer layer of P3HT:PCBM-based devices. The modification of QDs provides better band alignment between the organic/cathode interface, improves ZnO crystal quality, and increases photon absorption, leading to more effective carrier transport/collection. By employing this energy-harvesting scheme, short-circuit current density, open-circuit voltage, and fill factor of the OPV device after CGS QD modification are improved by 9.43%, 7.02% and 6.31%, respectively, giving rise to a 23.8% enhancement in the power conversion efficiency.

ZnO1-x nanorod arrays/ZnO thin film bilayer structure: from homojunction diode and high-performance memristor to complementary 1D1R application.

We present a ZnO(1-x) nanorod array (NR)/ZnO thin film (TF) bilayer structure synthesized at a low temperature, exhibiting a uniquely rectifying characteristic as a homojunction diode and a resistive switching behavior as memory at different biases. The homojunction diode is due to asymmetric Schottky barriers at interfaces of the Pt/ZnO NRs and the ZnO TF/Pt, respectively. The ZnO(1-x) NRs/ZnO TF bilayer structure also shows an excellent resistive switching behavior, including a reduced operation power and enhanced performances resulting from supplements of confined oxygen vacancies by the ZnO(1-x) NRs for rupture and recovery of conducting filaments inside the ZnO TF layer. A hydrophobic behavior with a contact angle of ~125° can be found on the ZnO(1-x) NRs/ZnO TF bilayer structure, demonstrating a self-cleaning effect. Finally, a successful demonstration of complementary 1D1R configurations can be achieved by simply connecting two identical devices back to back in series, realizing the possibility of a low-temperature all-ZnO-based memory system.