Effect of Slurry Viscosity and Dispersant Agent on the Sintering of 3Y-TZP Ceramics Fabricated by Slip Casting.

Dental zirconia implants are typically manufactured by mechanical machining of a zirconia block into a tooth shape. Many cracks are created by this machining process on the surface of the green body, which induces deterioration of mechanical strength and reliability of the sintered zirconia implant. In this study, we fabricated a dense zirconia specimen by slip casting and sintering. The zirconia slurry for slip casting was prepared by mixing yttria-stabilized zirconia powder with an average particle size of 20 nm, distilled water, and dispersant. Slurry viscosity was controlled by varying pH, dispersant concentration, and solid content; the lower viscosity being achieved at pH 11 controlled by ammonium hydroxide. With a dispersant content of 0.4-0.8 wt%, the viscosity was reduced from 190 cP to 40 cP at pH 11. After casting and sintering at 1550 °C for 2 h, the sintered body reached a density of 5.70-6.01 g/cm³ and a grain size of 300-700 nm, depending on the slurry preparation conditions.

Effect of Solid Loading on the Sintered Properties of 3 mol% Yttria-Stabilized Tetragonal Zirconia Polycrystals (3Y-TZP) Ceramics via Slip Casting.

Dental zirconia implants fabricated by the mechanical machining and sintering of zirconia blocks have many surface cracks that lead to the deterioration of mechanical strength and the failure of the implant in the body. In this study, we attempted to manufacture an extremely dense and crack-free zirconia specimen by slip casting and pressureless sintering. After the preparation of zirconia slurry by control of its viscosity and by solid loading, highly dense zirconia specimens could be obtained by pressureless sintering at 1450 °C for 2 h. Slurry viscosity was controlled by adjusting the mixing ratio of 3Y-TZP powder, a dispersant, and a pH adjustment agent. Highly dense 3Y-TZP specimens with a relative density of 99% and small grain size of 200-400 nm could be obtained at a solid loading of 50-65 wt%. An optimally dense specimen was fabricated from zirconia slurry with 60 wt% solid loading that had the highest apparent density of 6.07 g/cm³ (99.5%).

In-Vitro Mechanical Performance Study of Biodegradable Polylactic Acid/Hydroxyapatite Nanocomposites for Fixation Medical Devices.

Osteoconductive, biocompatible, and resorbable organic/inorganic composites are most commonly used in fixation medical devices, such as suture anchors and interference screws, because of their unique physical and chemical properties. Generally, studies on biodegradable composites have focused on their mechanical properties based on the composition and the individual roles of organic and inorganic biomaterials. In this study, we prepared biodegradable organic/inorganic nanocomposite materials using the solvent mixing process and conventional molding. We used polylactic acid (PLA) as the matrix and nano-sized hydroxyapatite (nano-HAp) as the osteoconductive filler. The content of nano-HAp was varied in 0-30 wt% and its influence on the In-Vitro mechanical performance of PLA/HAp nanocomposites was evaluated. The In-Vitro mechanical properties of nanocomposites were evaluated using standardized tensile and flexural tests after different immersion times in simulated body fluid.

Polylactic Acid/Nanostructured Si-Substituted ß-Tricalcium Phosphate Composites for Biodegradable Fixation Medical Devices.

Organic/inorganic biocomposite materials for biodegradable fixation medical devices require osteoconductivity, biocompatibility, and adequate mechanical properties with biodegradation behavior. The objective of this study was to investigate the effect of Si ions substituted in ß-tricalcium phosphate (ß-TCP) on the mechanical properties of organic/inorganic biocomposites. Biodegradable composite materials were prepared with polylactic acid (PLA) as the matrix and nano Si-substituted ß-TCP as the osteoconductive filler by solvent mixing and conventional molding. The nanostructured Si-substituted ß-TCP powders were synthesized by co-precipitation, controlling the quantity of Si ions. The amount of nanostructured Si-substituted ß-TCP powders in composites was varied in the 0-40 wt% range and the material properties were compared with those of pure ß-TCP/PLA composites. The influence of Si ions on the mechanical properties of the composites was evaluated by tensile and flexural tests.

Interfacial Property of Dental Cobalt­Chromium Alloys and Their Bonding Strength with Porcelains.

Porcelain-fused-to-metal crown is one of the widely-used prostheses among the dental porcelain restorations. Nonprecious metals like Ni­Cr and Co­Cr have extensively been used for metal-ceramic restorations due to advantages such as inexpensive price, hardness, durability, resistance to deformation, thin thickness of metal of porcelain area, and other mechanical and physical properties. However, the immediate advantage of the Co­Cr alloy is comparable performance to other base metal alloys, but without an allergenic nickel component. To achieve clinical longevity of porcelain-fused-to-metal (PFM) crowns, it is essential to have adequate bond strength between the metal substrate and porcelain. Any type of metal-ceramic fracture failure can become a costly and timeconsuming problem, both in the clinic and laboratory. Therefore, the suitability of the Co­Cr alloy for dental applications is critically associated with its ceramic bonding capacity. In this study, Co­Cr metal alloys modified by acid-etching and sandblasting, oxide layer was formed for subsequent bonding to porcelain ceramics. By both acid-etching and sandblasting oxide layer was formed and showed higher bonding strength at a proper condition, but debonding was occurred at porcelain layer so that they showed highest bonding strength by combined these two kind of surface treatment. Because the oxide film was formed more densely in a vacuum at the portions where more sophisticated concavo-convex were formed on the surface of a metal.

Surface Corrosion of Nanoscaled Hydroxyapatite During an In Vivo Experiment.

Hydroxyapatite (HA) is widely used as a bioactive ceramics as it forms a chemical bond with bone. However, the drawback to using this material is its inferior mechanical properties. In this research, surface corrosion and disintegration of nanoscaled HA in a dog were studied, and the mechanism by which phase-pure HA dissolved in vivo was investigated. Biological properties of HA in vivo are affected by the grain-boundary dissolution followed by a surface corrosion and microstructural disintegration. This kind of dissolution process, apparently evidenced at the grain boundary, causes particle generation, which indicates that both long-term bone in-growth and mechanical properties can dramatically deteriorate. Implant dissolution by osteoclasts in vivo is also observed on the surface of hydroxyapatite. Implant surface showed an aggressive corrosion by an osteoclast resorption. Severe and deeper dissolution underwent close to osteoclast resulting in formation of smaller and more round particle shape.

Fabrication and Microstructure of Hydroxyapatite Coatings on Zirconia by Room Temperature Spray Process.

Hydroxyapatite coatings were fabricated on zirconia substrates by a room temperature spray process and were investigated with regards to their microstructure, composition and dissolution in water. An initial hydroxyapatite powder was prepared by heat treatment of bovine-bone derived powder at 1100 °C for 2 h, while dense zirconia substrates were fabricated by pressing 3Y-TZP powder and sintering it at 1350 °C for 2 h. Room temperature spray coating was performed using a slit nozzle in a low pressure-chamber with a controlled coating time. The phase composition of the resultant hydroxyapatite coatings was similar to that of the starting powder, however, the grain size of the hydroxyapatite particles was reduced to about 100 nm due to their formation by particle impaction and fracture. All areas of the coating had a similar morphology, consisting of reticulated structure with a high surface roughness. The hydroxyapatite coating layer exhibited biostability in a stimulated body fluid, with no severe dissolution being observed during in vitro experimentation.

Influence of Starting Powders on Hydroxyapatite Coatings Fabricated by Room Temperature Spraying Method.

Three types of raw materials were used for the fabrication of hydroxyapatite coatings by using the room temperature spraying method and their influence on the microstructure and in vitro characteristics were investigated. Starting hydroxyapatite powders for coatings on titanium substrate were prepared by a heat treatment at 1100 °C for 2 h of bovine bone, bone ash, and commercial hydroxyapatite powders. The phase compositions and Ca/P ratios of the three hydroxyapatite coatings were similar to those of the raw materials without decomposition or formation of a new phase. All hydroxyapatite coatings showed a honeycomb structure, but their surface microstructures revealed different features in regards to surface morphology and roughness, based on the staring materials. All coatings consisted of nano-sized grains and had dense microstructure. Inferred from in vitro experiments in pure water, all coatings have a good dissolution-resistance and biostability in water.

The Role of Magnesium Ion Substituted Biphasic Calcium Phosphate Spherical Micro-Scaffolds in Osteogenic Differentiation of Human Adipose Tissue-Derived Mesenchymal Stem Cells.

This study was investigated the role of magnesium (Mg2+) ion substituted biphasic calcium phosphate (Mg-BCP) spherical micro-scaffolds in osteogenic differentiation of human adipose tissue-derived mesenchymal stem cells (hAT-MSCs). Mg-BCP micro-scaffolds with spherical morphology were successfully prepared using in situ co-precipitation and spray drying atomization process. The in vitro cell proliferation and differentiation of hAT-MSCs were determined up to day 14. After in vitro biological tests, Mg-BCP micro-scaffolds with hAT-MSCs showed more enhanced osteogenicity than pure hAT-MSCs as control group by unique biodegradation of TCP phase and influence of substituted Mg2+ ion in biphasic nanostructure. Therefore, these results suggest that Mg-BCP micro-scaffolds promote osteogenic differentiation of hAT-MSCs.

Antimicrobial HPA3NT3 peptide analogs: placement of aromatic rings and positive charges are key determinants for cell selectivity and mechanism of action.

In an earlier study, we determined that HP(2-20) (residues 2-20 of parental HP derived from the N-terminus of the Helicobacter pylori ribosomal protein L1) and its analog, HPA3NT3, had potent antimicrobial effects. However, HPA3NT3 also showed undesirable cytotoxicity against HaCaT cells. In the present study, we designed peptide analogs including HPA3NT3-F1A (-F1A), HPA3NT3-F8A (-F8A), HPA3NT3-F1AF8A (-F1AF8A), HPA3NT3-A1 (-A1) and HPA3NT3-A2 (-A2) in an effort to investigate the effects of amino acid substitutions in reducing their hydrophobicity or increasing their cationicity, and any resulting effects on their selectivity in their interactions with human cells and pathogens, as well as their mechanism of antimicrobial action. With the exception of HPA3NT3-A1, all of these peptides showed potent antimicrobial activity. Moreover, substitution of Ala for Phe at positions 1 and/or 8 of the HPA3NT3 peptides (-F1A, -F8A and -F1AF8A) dramatically reduced their cytotoxicity. Thus the cytotoxicity of HPA3NT3 appears to be related to its Phe residues (positions 1 and 8), which strongly interact with sphingomyelin in the mammalian cell membrane. HPA3NT3 exerted its bactericidal effects through membrane permeabilization mediated by pore formation. In contrast, fluorescent dye leakage and nucleic acid gel retardation assays showed that -A2 acted by penetrating into the cytoplasm, where it bound to nucleic acids and inhibited protein synthesis. Notably, Staphylococcus aureus did not develop resistance to -A2 as it did with rifampin. These results suggest that the -A2 peptide could potentially serve as an effective antibiotic agent against multidrug-resistant bacterial strains.