Aggregation-Induced Emission Properties of Glutathione and L-Cysteine Capped CdS Quantum Dots and their Application as Zn(II) Probe.

Targeting to obtain better water solubility and stability and less aggregation-caused quenching effects of quantum dots, two kinds of thiol molecules, glutathione and L-cysteine, were firstly united to offer stabilizing ligands for aqueous synthesized CdS quantum dots, which exhibited sensitive aggregation-induced emission properties. Fluorescent intensity of the CdS quantum dots was enhanced about 5 folds by simple solvent exchange from water to 90 vol% PEG200. Restriction of intramolecular motions in an aggregate state was probably the main cause of the phenomenon. At the same time, fluorescent intensity of CdS quantum dots in the presence of zinc ions was able to be enhanced about 2.2 folds. Based on the researches, a handy metal enhanced fluorescent probe for detecting zinc ions was established. And the detection limit was 0.58 µmol/L. Zinc ions as a bridge among CdS quantum dots to form aggregates limited motions of CdS quantum dots to a certain extent and simultaneously enhanced their fluorescence emission intensities. Meanwhile, activation of surface states of CdS quantum dots also led to emission enhancement. Both of the two factors together contributed to the fluorescence enhancement and ultimately to the sensitivity to zinc ion sample detection.

Preparation of magnetic molecularly imprinted polymers for the identification of zearalenone in grains.

This study was based on the specific binding ability of magnetic molecularly imprinted polymers (MMIPs) combined with a high-performance liquid chromatography-fluorescence detector (HPLC-FLD) for the rapid determination of zearalenone (ZEN) in cereals. A novel magnetic molecularly imprinted polymer was prepared by surface imprinting technology. Warfarin was used as a virtual template, 3-aminopropyl triethoxysilane (APTES) was used as the functional monomer, and tetraethyl orthosilicate (TEOS) was used as the cross-linking agent. Analysis by a vibrating sample magnetometer (VSM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) showed that MMIPs were prepared with a particle size about 450 nm, the imprinted molecular layer accounting for 10.7% of the total mass, and saturation magnetization of about 34.54 emu/g. The maximum adsorption capacity (Qmax) of the thermodynamic and kinetic adsorption experiments were 13.90 mg/g and 8.71 mg/g, respectively. The Langmuir model showed that the binding sites were uniformly distributed on the surface of the MMIPs. The Scatchard analysis showed that MMIPs had two types of binding sites with Qmax of 8.22 mg/g and 15.37 mg/g, respectively. In actual sample detection, the limit of detection (LOD) and limit of quantification (LOQ) were 0.4 ng/kg and 0.9 ng/kg, respectively. The sample recovery rate was 90.56-99.96%, the daytime stability was 1.35-2.87%. These results showed that MMIPs had good performance in selectively identifying ZEN and were suitable for determining ZEN in cereals.

Assay of ceftazidime and cefepime based on fluorescence quenching of carbon quantum dots.

A novel and sensitive method for the determination of ceftazidime and cefepime in an active pharmaceutical ingredient (API) has been developed based on the fluorescence quenching of poly(ethylene glycol) (PEG)2000-capped carbon quantum dots (CQDs) prepared using a chemical oxidation method. The quenching of fluorescence intensity is proportional to the concentration of ceftazidime and cefepime over the range of 0.33-3.30 and 0.24-2.40 µg/mL, respectively. The mode of interaction between PEG2000-capped CQDs and ceftazidime/cefepime in aqueous solutions was investigated using a fluorescence, UV/Vis and Fourier transform infrared spectrometry (FTIR) at physiological pH. UV/Vis and FTIR spectra demonstrated that ground state compounds were formed through hydrophobic interaction the fluorescence quenching of CQDs caused by ceftazidime and cefepime. The quenching constants decreased with increases in temperature, which was consistent with static quenching.

Preparation of magnetic molecularly imprinted polymer for selective identification of patulin in juice.

A highly efficient and selective method was successfully developed by using magnetic molecularly imprinted polymers (MMIPs) combined with high performance liquid chromatography (HPLC) to quickly determine patulin (PAT) in juice. MMIPs was prepared by surface imprinting method using Fe3O4 nanoparticles as supporter, 2-oxindole as virtual template, (3-Aminopropyl) triethoxysilane (APTES) as functional monomer and tetraethyl orthosilicate (TEOS) as crosslinking agent. The structure of the product was characterized by vibrating sample magnetometer (VSM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). The results showed that MMIP with a particle size of about 450 nm was successfully prepared, the imprinted molecular layer accounted for about 11.6% of the total mass, and the saturation magnetization was about 6.82 emu/g. The maximum adsorption capacities (Qmax) of kinetic and thermodynamic adsorption experiments were 1.97 mg/g and 4.241 mg/g, respectively. The adsorption process was highly selective and fitted well with the pseudo-second-order model. Langmuir model demonstrated that the binding sites were evenly distributed on the surface of the MMIPs. Scatchard analysis showed that MMIPs had two types of binding sites with Qmax of 4.53 mg/g and 5.73 mg/g, respectively. In the actual sample application, the limit of detection (LOD) and the limit of quantification (LOQ) were 3 µg/kg and 10 µg/kg. And the recovery rate of the sample was 86.44-95.50%. MMIPs possessed excellent applicability with stability of 1.11-3.16% and accuracy of 0.63-1.94%. These results indicated that MMIPs had good performance in separating PAT and was suitable for determining PAT in actual samples.