[Effect of printing orientation on physical and mechanical properties of 3D printing prosthodontic base resin materials].

OBJECTIVE: To analyze the influence of forming direction on the surface characteristics, elastic modulus, bending strength and fracture toughness of printed parts and the relationship between forming direction and force direction, and to provide scientific basis and guidance for the clinical application of oral denture base resin materials. METHODS: The 3D printing technology was used to print denture base resin samples. The shape and size of the samples referred to the current standard for testing conventional denture base materials. The samples used for physical performance testing were cylindrical (with a diameter of 15 mm and a thickness of 1 mm) and printed at different angles along the Z axis (0°, 45°, 90°). Scanning electron microscope was used to observe the microscopic topography of the different samples. The color stability of different samples was observed by color stabilizer. The surface roughness of the samples was analyzed by using surface roughness tester. The Vickers hardness was measured to analyze the hardness of the samples. The samples used for mechanical performance testing were rectangular (elastic modulus and bending strength: A length of 64 mm, a width of 10 mm, and a height of 3.3 mm; fracture toughness: A length of 39 mm, a width of 8 mm, and a height of 4 mm), divided into two groups: W group and H group. The W group was printed from the bottom up along the Z axis with the length × width as the bottom surface parallel to the X, Y axis plane, while the H group printed from the bottom up along the Z axis with the length × height as the bottom surface parallel to the X, Y axis plane. The forming angles of both groups were equally divided into 0°, 45°, and 90°. The elastic modulus, bending strength and fracture toughness of different samples were studied through universal mechanical testing machine. SPSS 22.0 software was used for statistical analysis. RESULTS: The microscopic topography and roughness of different samples were closely related to the printing direction, with significant differences between the 0°, 45°, and 90° specimens. The 0° specimens had the smoothest surface (roughness < 1 µm). The surface of the 45° specimen was the roughest (roughness>3 µm). The microhardness of the 0° sample was the best [(196.13±0.20) MPa], with a significant difference compared with the 90° sample [(186.62±4.81) MPa, P < 0.05]. The mechanical properties of different samples were also closely related to the printing direction. The elastic modulus, bending strength, and fracture toughness of the 45° samples in the W group were the highest compared with the other groups. The results of elastic modulus showed that in the H group, the 45° specimens had the highest elastic mo-dulus, which was significantly different from the 0° and 90° specimens (P < 0.05). The elastic modulus of 0° and 45° specimens in the W group were higher than those in 90° specimens (P < 0.05). The bending strength results showed that there was no significant difference between the specimens from dif-ferent angles in the H group. The bending strength of the 90° specimens in the W group was the smallest, and there was a significant difference between 90° and the 0° and 45° specimens (P < 0.05); And the bendind strength of the 0° and 45° specimens in the W group was significantly higher than that of the 0° and 45° specimens in the H group (P < 0.05). The fracture toughness results showed that the fracture toughness of the H group specimens was lower than 1.9 MPa m1/2, which was specified in the denture base standard. The 45° samples in the W group were the highest, with significant differences compared with the 0° and 90° samples (P < 0.05). And the 90° samples of the W group specimens were lower than 1.9 MPa m1/2. And the fracture toughness of the 45° specimen in the W group was significantly higher than that of all the specimens in the H group (P < 0.05). CONCLUSION: The 0° samples had relatively better physical properties. The 45° samples had the best mechanical properties. But the fracture toughness of specimens (H group and 90° samples of W group) did not yet meet clinical requirements. That indicated that the characteristics of the 3D printing denture base resin were affected by the printing direction. Only when the performance of the printed samples in all directions met the minimum requirements of the standard, they could be used in clinical practice.

Oriented face-centered cubic to hexagonal close-packed martensitic transition, grain morphology, and mechanical properties of Co-Cr alloy fabricated by selective laser melting.

STATEMENT OF PROBLEM: Removable partial dentures (RPDs) can be fabricated by selective laser melting (SLM) with different build orientations. How microstructures and mechanical properties of SLM Co-Cr alloy are affected by different build orientations is unclear. PURPOSE: The purpose of this in vitro study was to investigate the phase structures, grain morphology, and mechanical properties of SLM Co-Cr alloy with different build orientations. MATERIAL AND METHODS: SLM Co-Cr tensile specimens were fabricated at orientation angles of 0, 45, and 90 degrees between the building and longitudinal direction named the T0, T45, and T90 design groups (n=14). Mechanical properties were obtained by tensile testing conducted by using a universal testing machine according to the International Organization for Standardization (ISO) 22674. The grains along the longitudinal direction of the specimens and phase structures were observed before and after tensile testing by electron backscatter diffraction. One-way analysis of variance followed by the Bonferroni post hoc test and Kruskal-Wallis test were used for statistical analysis (α=.05). RESULTS: The 0.2% yield strengths in descending order were T90 (870 MPa)>T45 (840 MPa)>T0 (786 MPa) (P<.05); the elongations were T0 (21.8%)>T45 (15.6%)>T90 (8.7%) (P<.05); the ultimate tensile strengths were T45 (1226 MPa)>T90 (1200 MPa)>T0 (1149 MPa) (P<.05). The average grain sizes in the T0, T45, and T90 groups were 22 µm, 18 µm, and 14 µm, respectively. After the tensile test, a face-centered cubic (FCC) to hexagonal close-packed (HCP) martensitic transition was found in each group, and the phase transition area fractions were T0 (38.3%)>T45 (11.4%)>T90 (0.7%). CONCLUSIONS: The FCC to HCP martensitic transition, grain morphology, and mechanical properties of SLM Co-Cr alloy depended on the build orientations. The oriented phase transition and grains affected the anisotropic mechanical properties of SLM Co-Cr alloy.

Effectiveness and cytotoxicity of two desensitizing agents: a dentin permeability measurement and dentin barrier testing in vitro study.

BACKGROUND: When evaluating the efficacy and safety of various desensitizing products in vitro, their mechanism of action and clinical utility should be considered during test model selection. This study aimed to evaluate the effects of two desensitizers, an in-office use material and an at-home use material, on dentin specimen permeability, and their dentin barrier cytotoxicity with appropriate test models. METHODS: Two materials, GLUMA desensitizer (GLU) containing glutaraldehyde and remineralizing and desensitizing gel (RD) containing sodium fluoride and fumed silica, were selected. Human dentin specimens were divided into three groups (n = 6): in groups 1 and 2, GLU was applied, and in group 3, RD was applied and immersed in artificial saliva (AS) for 24 h. Dentin specimen permeability before and after each treatment/post-treatment was measured using a hydraulic device under a pressure of 20 cm H2O. The perfusion fluid was deionized water, except in group 2 where 2% bovine serum albumin (BSA) was used. The representative specimens before and after treatment from each group were investigated using scanning electron microscopy. To measure cytotoxicity, test materials were applied to the occlusal surfaces of human dentin disks under which three-dimensional cell scaffolds were placed. After 24-h contact within the test device, cell viability was measured via 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays. RESULTS: GLU significantly reduced the dentin permeability and occluded the dentinal tubules when 2% BSA was used as perfusion fluid. RD significantly reduced dentin permeability and occluded the tubules, but permeability rebounded after AS immersion. GLU significantly decreased cell viability, but RD was non-cytotoxic. CONCLUSIONS: In vitro GLU application induced effective dentinal tubule occlusion only following the introduction of simulated dentinal fluid. RD provided effective tubule occlusion, but its full remineralization potential was not realized after a short period of immersion in AS. GLU may harm the pulp, whereas RD is sufficiently biocompatible.

Effect of the prosthetic index on stress distribution in Morse taper connection implant system and peri-implant bone: a 3D finite element analysis.

BACKGROUND: The combination of a prosthetic index with Morse taper connection was developed, with the purpose of making prosthetic procedures more precise. However, the presence of the index may compromise the mechanical performance of the abutment. The aim of this study is to evaluate the effect of prosthetic index on stress distribution in implant-abutment-screw system and peri-implant bone by using the 3D finite element methodology. METHODS: Two commercial dental implant systems with different implant-abutment connections were used: the Morse taper connection with platform switching (MT-PS) implant system and the internal hex connection with platform matching (IH-PM) implant system. Meanwhile, there are two different designs of Morse taper connection abutment, namely, abutments with or without index. Consequently, three different models were developed and evaluated: (1) MT-PS indexed, (2) MT-PS non-indexed, and (3) IH-PM. These models were inserted into a bone block. Vertical and oblique forces of 100 N were applied to each abutment to simulate occlusal loadings. RESULTS: For the MT-PS implant system, the maximum stress was always concentrated in the abutment neck under both vertical and oblique loading. Moreover, the maximum von Mises stress in the neck of the MT-PS abutment with index even exceed the yield strength of titanium alloy under the oblique loading. For the IH-PM implant system, however, the maximum stress was always located at the implant. Additionally, the MT-PS implant system has a significantly higher stress level in the abutment neck and a lower stress level around the peri-implant bone compared to the IH-PM implant system. The combined average maximum stress from vertical and oblique loads is 2.04 times higher in the MT-PS indexed model, and 1.82 times for the MT-PS non-indexed model than that of the IH-PM model. CONCLUSIONS: MT-PS with index will cause higher stress concentration on the abutment neck than that of without index, which is more prone to mechanical complications. Nevertheless, MT-PS decreases stress within cancellous bone and may contribute to limiting crestal bone resorption.

Effects of Microplastics on Microbial Community in Zhanjiang Mangrove Sediments.

Microplastics are easily consumed by marine animals, thereby entering the food chain and endangering animal health. However, there are few studies focusing on the effects of microplastics in mangrove sediments on microbial communities. In order to study the influence of microplastics on microorganisms, microplastics and microorganisms were extracted from Zhanjiang (Guangdong Province, China) mangrove sediments and analyzed. The results showed that there were differences in Shannon and Simpson indices of the microbial community in microplastics (p < 0.05), and there were also differences between JG30_KF_CM45 and Natranaerovirga at the genus level, indicating that microplastics may affect the diversity and composition of microorganisms in sediments. In addition, FAPROTAX function prediction analysis showed that microplastics may affect the nitrification of microbial communities. The results from this study indicate that microplastics affected the diversity and richness of microorganisms in mangrove sediments, which provides an experimental basis for the relationship between microplastics and microorganisms.

Network meta-analysis of the treatment efficacy of different lasers for peri-implantitis.

The aim of this study was comparing different lasers with conventional non-surgical treatment (CNT) for the management of peri-implantitis, regarding probing depth (PD), plaque index (PLI), clinical attachment level (CAL), and sulcus bleeding index (SBI). Randomized controlled trials (RCTs) on different lasers and CNT for peri-implantitis were searched. Pairwise and network meta-analyses were performed to analyze the PD, PLI, CAL, and SBI outcomes. The risk of bias, evidence quality, statistical heterogeneity, and ranking probability were also evaluated. Eleven studies were included in this study, involving three types of lasers. Diode + CNT had significantly superior efficacy to CNT alone, regarding PD reduction, while Er:YAG + CNT had significantly superior efficacy than CNT in terms of the PLI, CAL, and SBI. The highest probability of being most effective for PD was diode + CNT (49%), while Er:YAG + CNT had the highest probability of improving the PLI, CAL, and SBI (66%, 53%, and 79%, respectively). Diode + CNT was significantly superior for PD management in peri-implantitis compared with CNT alone, while Er:YAG + CNT significantly improved the PLI, CAL, and SBI. Therefore, Er:YAG + CNT might be recommended methods considered for management of peri-implantitis.

Contribution of phenylpropanoid metabolism to plant development and plant-environment interactions.

Phenylpropanoid metabolism is one of the most important metabolisms in plants, yielding more than 8,000 metabolites contributing to plant development and plant-environment interplay. Phenylpropanoid metabolism materialized during the evolution of early freshwater algae that were initiating terrestrialization and land plants have evolved multiple branches of this pathway, which give rise to metabolites including lignin, flavonoids, lignans, phenylpropanoid esters, hydroxycinnamic acid amides, and sporopollenin. Recent studies have revealed that many factors participate in the regulation of phenylpropanoid metabolism, and modulate phenylpropanoid homeostasis when plants undergo successive developmental processes and are subjected to stressful environments. In this review, we summarize recent progress on elucidating the contribution of phenylpropanoid metabolism to the coordination of plant development and plant-environment interaction, and metabolic flux redirection among diverse metabolic routes. In addition, our review focuses on the regulation of phenylpropanoid metabolism at the transcriptional, post-transcriptional, post-translational, and epigenetic levels, and in response to phytohormones and biotic and abiotic stresses.

Compound heterozygous mutations in the ALDH3A2 gene cause Sjögren-Larsson syndrome: a case report.

Purpose: Sjögren-Larsson syndrome is a rare, autosomal, recessive neurocutaneous disorder caused by mutations in the ALDH3A2 gene, which encodes the fatty aldehyde dehydrogenase enzyme. Deficiency in fatty aldehyde dehydrogenase results in an abnormal accumulation of toxic fatty aldehydes in the brain and skin, which cause spasticity, intellectual disability, ichthyosis, and other clinical manifestations. We present the clinical features and mutation analyses of a case of SLS.Materials and Methods: The family history and clinical data of the patient were collected. Genomic DNA was extracted from peripheral blood samples of the patient and her parents, and next-generation sequencing was performed. The candidate mutation sites that required further validation were then sequenced by Sanger sequencing. Bioinformatics software PSIPRED and RaptorX were used to predict the secondary and tertiary structures of proteins.Results: The patient, a five-year-old girl with complaints of cough for three days and intermittent convulsions for seven hours, was admitted to the hospital. Other clinical manifestations included spastic paraplegia, mental retardation, tooth defects, and ichthyosis. Brain magnetic resonance imaging showed periventricular leukomalacia. Genetic screening revealed compound heterozygous mutations in the ALDH3A2 gene: a frameshift mutation c.779delA (p.K260Rfs*6) and a missense mutation c.1157A > G (p.N386S). Neither of the ALDH3A2 alleles in the compound heterozygote patient were able to generate normal fatty aldehyde dehydrogenase, which were likely responsible for her phenotype of Sjögren-Larsson syndrome.Conclusion: The compound heterozygous mutations found in the ALDH3A2 gene support the diagnosis of Sjögren-Larsson syndrome in the patient and expand the genotype spectrum of the gene.

Crystal growth in dentinal tubules with bio-calcium carbonate-silica sourced from equisetum grass.

BACKGROUND/PURPOSE: One effective way to deal with dentin hypersensitivity is to develop materials to seal the tubules. The porous bio-calcium carbonate-silica (BCCS) contained well-dispersed CaCO3 would form calcium phosphates to seal the dentinal tubules when mixed with an acidic solution. The acidic hydrothermal treatment and calcination to isolate the BCCS from the agricultural waste like equisetum grass was used, which would be more environmentally friendly than chemically synthesized mesoporous biomaterials. The aim of this study was to develop mesoporous materials from natural resources to occlude the dentinal tubules which could be more environmentally-friendly. METHODS: Dentin disc samples were prepared and treated with different methods as follows: (1) BCCS mixed with H3PO4; (2) BCCS mixed with KH2PO4; (3) Seal & Protect® was used as a comparison group. Sealing efficacy was evaluated by measuring the depths and percentages of precipitate occlusion in dentinal tubules with SEM. RESULTS: The N2 adsorption-desorption isotherm of the BCCS demonstrated a pore size of around 15.0 nm and a surface area of 61 m2g-1. From the results of occlusion percentage and depth, the BCCS treated with H3PO4 or KH2PO4 demonstrated promising sealing efficacy than the commercial product. CONCLUSION: This synthetic process used the agricultural waste equisetum grass to produce bio-calcium carbonate-silica would be environmentally friendly, which has great potential in treating exposed dentin related diseases.

Comparison of technical, biological, and esthetic parameters of ceramic and metal-ceramic implant-supported fixed dental prostheses: A systematic review and meta-analysis.

STATEMENT OF PROBLEM: Differences between ceramic and metal-ceramic implant-supported fixed dental prostheses are unclear. PURPOSE: The purpose of this systematic review and meta-analysis was to compare the technical, biological, and esthetic complication rates of implant-supported ceramic and metal-ceramic restorations. MATERIAL AND METHODS: Six databases were searched to identify randomized controlled clinical trials (RCTs) and prospective and retrospective cohort studies of implant-supported fixed dental prostheses. The survival rate, marginal adaptation, marginal bone loss, pocket probing depth, crown color match, and mucosal discoloration of ceramic and metal-ceramic single crowns were assessed. For implant-supported fixed partial dental prostheses (FPDPs), only the survival rate was assessed. The risk of bias was assessed for individual studies and across studies by using the Cochrane guidelines, Newcastle-Ottawa scale, and funnel plots. RESULTS: Twenty studies were included in this meta-analysis. Ceramic and metal-ceramic implant-supported single crowns were compared in terms of the survival rate (OR=0.84 [0.32, 2.23], P=.730), marginal adaptation (mean difference [MD]=0.33 [0.19, 0.47], P<.001), marginal bone loss (MD=-0.03 [-0.07, 0.02], P=.260), pocket probing depth (MD=-0.07 [-0.14, 0.00], P=.060), crown color match (MD=-0.15 [-0.29, 0.00], P=.040), and mucosal discoloration (standardized mean difference [SMD]=-0.14 [-0.86, 0.58], P=.710). The survival rate of ceramic and metal-ceramic implant-supported FPDPs was also compared (odds ratio [OR]=1.92 [1.26, 2.94], P=.003). CONCLUSIONS: No significant difference was observed between ceramic and metal-ceramic implant-supported single crowns in terms of the survival rate, marginal bone loss, pocket probing depth, or mucosal discoloration. However, metal-ceramic single crowns had better marginal adaptation and poorer crown color match than did ceramic single crowns. In addition, current evidence indicates that metal-ceramic implant-supported FPDPs might have a higher survival rate than ceramic FPDPs.

Crystal Structures of the C-Terminally Truncated Endoglucanase Cel9Q from Clostridium thermocellum Complexed with Cellodextrins and Tris.

Endoglucanase CtCel9Q is one of the enzyme components of the cellulosome, which is an active cellulase system in the thermophile Clostridium thermocellum. The precursor form of CtCel9Q comprises a signal peptide, a glycoside hydrolase family 9 catalytic domain, a type 3c carbohydrate-binding module (CBM), and a type I dockerin domain. Here, we report the crystal structures of C-terminally truncated CtCel9Q (CtCel9QΔc) complexed with Tris, Tris+cellobiose, cellobiose+cellotriose, cellotriose, and cellotetraose at resolutions of 1.50, 1.70, 2.05, 2.05 and 1.75 Å, respectively. CtCel9QΔc forms a V-shaped homodimer through residues Lys529-Glu542 on the type 3c CBM, which pairs two ß-strands (ß4 and ß5 of the CBM). In addition, a disulfide bond was formed between the two Cys535 residues of the protein monomers in the asymmetric unit. The structures allow the identification of four minus (-) subsites and two plus (+) subsites; this is important for further understanding the structural basis of cellulose binding and hydrolysis. In the oligosaccharide-free and cellobiose-bound CtCel9QΔc structures, a Tris molecule was found to be bound to three catalytic residues of CtCel9Q and occupied subsite -1 of the CtCel9Q active-site cleft. Moreover, the enzyme activity assay in the presence of 100 mm Tris showed that the Tris almost completely suppressed CtCel9Q hydrolase activity.

Surface functionalization of titanium with zinc/strontium-doped titanium dioxide microporous coating via microarc oxidation.

Deficient osseointegration and implant-related infections are pivotal issues for the long-term clinical success of titanium (Ti) implants. Zinc (Zn) and strontium (Sr) serve dual functions by promoting osteogenesis and inhibiting bone destruction, and Zn has good antibacterial activity. As such, this study examined the preparation of a Zn/Sr-doped titanium dioxide microporous coating (MT-Zn/Sr) on a Ti surface using microarc oxidation (MAO), with Zn and Sr evenly distributed throughout the coating. In vitro, the coating could promote the adhesion, proliferation, differentiation and mineralization of osteoblasts, showing good biological activity. Antibacterial testing demonstrated the good antibacterial activity of the coating, as it inhibited the proliferation of Staphylococcus. In vivo, MT-Zn/Sr promoted early osseointegration between the Ti substrate and the bone tissue. This work is expected to provide a new method for improving the biological activity of Ti implants and thus has important theoretical significance and great clinical prospects.

Effects of two disinfection/sterilization methods for dentin specimens on dentin permeability.

OBJECTIVES: To investigate the effects of two disinfection/sterilization methods on the permeability of dentin specimens. MATERIALS AND METHODS: Forty intact human third molars were freshly extracted and cut, close to the pulp chamber, into dentin disks with a 500-µm thickness. The disks were randomized (n = 20 each) into a 70% ethanol group (acid-etched dentin disks soaked in 70% ethanol for 15 min) and a steam autoclaving group (acid-etched dentin disks autoclaved for 25 min). The permeability (Lp) of each dentin disk was measured before and after either treatment using a hydraulic device, and intra- and inter-group differences in values before and after treatment were analyzed using t tests. Field emission scanning electron microscopy (FE-SEM) micrographs of the dentin surface were acquired and examined. FE-SEM samples were prepared using the critical point drying (CPD) method. RESULTS: Immersion in 70% ethanol increased the Lp values of dentin specimens by 17%, which was not statistically significant. Steam autoclaving significantly reduced dentin permeability by 66% because the dentin collagen mesh became compact and collapsed, as detected by FE-SEM. CONCLUSIONS: The disinfection of acid-etched dentin disks using 70% ethanol for 15 min does not significantly affect dentin permeability, whereas sterilization of acid-etched dentin disks via autoclaving significantly reduces dentin permeability. CLINICAL RELEVANCE: Considering the influences of dentin permeability by disinfection/sterilization methods, the disinfection of the acid-etched dentin disks using 70% ethanol for 15 min could be used for the study related to dentin permeability, while the sterilization of autoclaving could not.

Effect of Lasers on Dentine Hypersensitivity: Evidence From a Meta-analysis.

OBJECTIVES: The aim of the study was to evaluate the immediate and long-term desensitizing effect of lasers in reducing dentine hypersensitivity (DH) compared with negative controls. MATERIAL AND METHODS: Six databases were searched to identify relevant articles published up to June 8, 2018. Randomized controlled trials comparing lasers with placebo or no treatment control in adult patients who suffer from DH were included. The risk of bias was assessed according to the Cochrane guidelines, and the quality of the evidence was evaluated using the Grading of Recommendations Assessment, Development and Evaluation tool. Inverse-variance random effects meta-analyses of standardized mean differences and 95% confidence intervals were performed using the RevMan 5.3 software. RESULTS: Twenty-two randomized controlled trials were finally included in the meta-analysis, and 21 studies of these were conducted to analyze the immediate and long-term effects. All types of lasers had better immediate and long-term desensitizing effects on DH than negative controls. The quality of evidence of the included studies showed that lasers compared with negative controls had moderate-quality immediate and long-term effects on DH. The statistical heterogeneity of these comparisons was high, for which the result of I2 ranged from 90% to 98%. CONCLUSIONS: Our results indicate that all types of lasers had a better desensitizing effect on DH than negative controls, both in immediate and long term. Furthermore, more high-quality studies with a large sample size are needed to confirm our results (PROSPERO CRD42018102260).

Porous zirconia ceramic as an alternative to dentin for in vitro dentin barriers cytotoxicity test.

OBJECTIVES: This study assessed the potential of porous zirconia ceramic as an alternative to dentin via an in vitro dentin barrier cytotoxicity test. METHODS: The permeability of dentin and porous zirconia ceramic was measured using a hydraulic-conductance system, and their permeability was divided into two groups: high and low. Using an in vitro dentin barrier test, the cytotoxicity of dental materials by dentin and porous zirconia ceramic was compared within the same permeability group. The L-929 cell viability was assessed by MTT assay. RESULTS: The mean (SD) permeability of the high and low group for dentin was 0.334 (0.0873) and 0.147 (0.0377) µl min-1 cm-2 cm H2O-1 and for zirconia porous ceramic was 0.336 (0.0609) and 0.146 (0.0340) µl min-1 cm-2 cm H2O-1. The cell viability of experimental groups which are the low permeability group was higher than that of the high permeability group for both dentin and porous zirconia ceramic as a barrier except for Maxcem Elite™ by porous zirconia ceramic. There was no significant difference between dentin and porous zirconia ceramic in cell viability, within either the high or low permeability group for all materials. The SD for cell viability of the porous zirconia ceramic was less than that of the dentin, across all materials within each permeability group, except for Maxcem Elite™ in the high permeability group. CONCLUSIONS: Porous zirconia ceramic, having similar permeability to dentin at the same thickness, can be used as an alternative to dentin for in vitro dentin barrier cytotoxicity tests. CLINICAL RELEVANCE: In vitro dentin barrier cytotoxicity tests when a standardized porous zirconia ceramic was used as a barrier could be useful for assessing the potential toxicity of new dental materials applied to dentin before applying in clinical and may resolve the issue of procuring human teeth when testing proceeds.

Effects of heat treatment on metal-ceramic combination of selective-laser-melted cobalt-chromium alloy.

STATEMENT OF PROBLEM: Components fabricated by selective laser melting (SLM) deform because of residual stress, but heat treatment allows the release of that stress and avoids deformation. Although dental cobalt-chromium (Co-Cr) alloy has been specifically designed for SLM, the effects of heat treatment on the metal-ceramic combination of SLM Co-Cr restorations require investigation. PURPOSE: The purpose of this in vitro study was to evaluate the effects of heat treatment on the metal-ceramic combination of SLM Co-Cr alloy. MATERIAL AND METHODS: Following ISO 9693:2012, Co-Cr metal strips (Solibond C Plus cast alloy and SLM powders; YETI Dental) were fabricated with a dimension of 25×3×0.5 mm by casting and SLM. The SLM specimens were divided into 3 subgroups (n=15 for each subgroup). Two subgroups were subjected to heat treatment at 880°C (SLM-880) and 1100°C (SLM-1100). The third subgroup was not subjected to heat treatment and served as a control (As-SLM). Cast specimens (n=15) also acted as a control. A porcelain layer with a thickness of 1.1 mm was fired to the central area (3×8 mm) of each specimen. The 3-point bend test was used to evaluate the metal-ceramic bond strength (τb). The fractured metal surfaces were examined by the naked eye, using a digital camera, and also using a scanning electron microscope. The area fraction of adherence porcelain (AFAP) was determined by measuring the atomic percentage of silicon using energy-dispersive x-ray spectroscopy (EDS). One-way ANOVA and the Kruskal-Wallis test, followed by the Mann-Whitney test (α=.05), were used for statistical analysis. RESULTS: The 1-way ANOVA found no significant difference in the bond strength among the 4 groups. The EDS analysis indicated that specimens in the groups receiving heat treatment (SLM-880 and SLM-1100) showed higher AFAP values than those in the As-SLM group (P<.05). The SLM-880 also showed significantly higher AFAP values than the SLM-1100. Compared with the cast group, significant differences in AFAP values were also observed, and the specimens in the order of highest to lowest AFAP values were SLM-880>cast>As-SLM; no significant difference was found between the SLM-1100 and cast groups. CONCLUSIONS: Heat treatment at 880°C and 1100°C did not affect the metal-ceramic bond strength of Co-Cr alloy made by SLM but did improve the porcelain adherence. SLM-fabricated and heat-treated Co-Cr alloy shows comparable or more porcelain adherence than cast specimens.

Effect of two heat treatments on mechanical properties of selective-laser-melted Co-Cr metal-ceramic alloys for application in thin removable partial dentures.

STATEMENT OF PROBLEM: Heat treatment has been used to reduce the residual stress of alloys fabricated by selective laser melting (SLM) to avoid deformation. Co-Cr metal-ceramic alloys are used to fabricate metal-ceramic restorations and removable partial dentures (RPDs) on the same substrate by SLM. A heat treatment that enables the fabrication of metal-ceramic restorations and RPDs with excellent mechanical properties should be evaluated. PURPOSE: The purpose of this in vitro study was to determine the effects of 2 heat treatments on the mechanical properties of SLM Co-Cr metal-ceramic alloys intended for the fabrication of thin RPDs. MATERIAL AND METHODS: Tensile bars were manufactured using cast metal-ceramics (C-MC group), RPD alloys (C-RPD group), and SLM Co-Cr metal-ceramic alloys. The SLM specimens were subjected to 2 different heat treatments, L1 at 880°C and L2 at 1100°C, and were further divided into subgroups (L1-MC, L1-RPD, L2-MC, and L2-RPD). Thirty-six tensile specimens were prepared in C-RPD, L1-RPD, and L2-RPD (simulated partial denture alloys for clinical use) and in C-MC, L1-MC, and L2-MC (simulated metal-ceramic alloys); 18 metal-ceramic bond strength specimens were prepared in C-MC, L1-MC, and L2-MC groups (n=6). The tensile test and 3-point bend test were conducted using a universal testing machine. The fracture surfaces of the L2-RPD tensile bar were examined using a scanning electron microscope. The Student t test (α=.05) was used for statistical analysis. RESULTS: No significant differences were observed between the bond strengths of L1-MC and C-MC (P=.74) or between those of L2-MC and C-MC (P=.124). The 0.2% yield strength (σ0.2) and elongation of all SLM specimens exceeded the minimum requirements required for the fabrication of thin RPDs as prescribed in ISO 22674:2016. The σ0.2 value of L1-MC and L2-MC was significantly higher than that of C-MC. Significant differences in σ0.2 values were found among the 3 RPD groups, L1-RPD>L2-RPD>C-RPD. For the elongation, significant differences were found among the 3 groups, L2-RPD>C-RPD>L1-RPD. The fracture surface of L2-RPD showed clear submicroscale dimples with fusion defects. CONCLUSIONS: When Co-Cr metal copings and RPD frameworks were fabricated on the same substrate simultaneously using SLM, heat treatment at 1100°C was found more suitable than at 880°C to release residual stress, considering the toughness required for dental prostheses.

Conformations of a Metastable SH3 Domain Characterized by smFRET and an Excluded-Volume Polymer Model.

Conformational states of the metastable drkN SH3 domain were characterized using single-molecule fluorescence techniques. Under nondenaturing conditions, two Förster resonance energy transfer (FRET) populations were observed that corresponded to a folded and an unfolded state. FRET-estimated radii of gyration and hydrodynamic radii estimated by fluorescence correlation spectroscopy of the two coexisting conformations are in agreement with previous ensemble x-ray scattering and NMR measurements. Surprisingly, when exposed to high concentrations of urea and GdmCl denaturants, the protein still exhibits two distinct FRET populations. The dominant conformation is expanded, showing a low FRET efficiency, consistent with the expected behavior of a random chain with excluded volume. However, approximately one-third of the drkN SH3 conformations showed high, nearly 100%, FRET efficiency, which is shown to correspond to denaturation-induced looped conformations that remain stable on a timescale of at least 100 µs. These loops may contain interconverting conformations that are more globally collapsed, hairpin-like, or circular, giving rise to the observed heterogeneous broadening of this population. Although the underlying mechanism of chain looping remains elusive, FRET experiments in formamide and dimethyl sulfoxide suggest that interactions between hydrophobic groups in the distal regions may play a significant role in the formation of the looped state.

Developmental toxicity, oxidative stress, and related gene expression induced by dioxin-like PCB 126 in zebrafish (Danio rerio).

3,3',4,4',5-Pentachlorobiphenyl (PCB126) cause multiple adverse effects in organisms including animals and humans. Although PCB toxicities are linked to oxidative damage in rodents, the mechanism in early life stages of zebrafish is not clear. To explore the developmental toxicity mechanism of PCB126, three paradigms (toxicological phenotypes, biochemical changes, and molecular changes) were studied in 3-h postfertilization (hpf) zebrafish (Danio rerio) embryos exposed to different PCB126 concentrations (0, 16, 32, 64, and 128 µg/L) until 168 hpf. Developmental malformations, including pericardial and yolk sac edema, impaired lower jaw growth, spinal curvature, head edema and failure to inflate the swim bladder were observed, some as early as 72 hpf. Mortality was not apparent in early stages but significantly increased in a dose-dependent manner from 144 hpf onward. A dose-dependent significant increase in malformation rate was observed from 72 hpf onward with up to 100% at 132 hpf in embryos exposed to 128 µg/L of PCB126. Higher doses of PCB126 significantly decreased the copper-zinc superoxide dismutase (CuZn-Sod), catalase (Cat), and glutathione peroxidase (Gpx) enzyme activities at 96, 132 hpf, but markedly declined from thereafter. PCB126 at 128 µg/L significantly increased the malondialdehyde content at 72, 96, and 132 hpf. The transcriptional gene expression of antioxidant enzymes Cat and Gpx was upregulated in embryos exposed to 64 µg/L of PCB126 at 24 and 96 hpf. Sod1 messenger RNA (mRNA) was low in embryos exposed to 32 µg/L at 72 and 96 hpf but was induced in embryos exposed to 64 and 128 µg/L doses at 132 hpf. Collectively, the results suggest oxidative stress as a major factor in the induction of multiple developmental abnormalities in early life stages of zebrafish exposed to PCB126. However, the relationship between the antioxidant enzyme activity and the mRNA expression was not clear and the potential reasons for this are discussed.

Developmental toxicity, EROD, and CYP1A mRNA expression in zebrafish embryos exposed to dioxin-like PCB126.

Dioxin-like PCB126 is a persistent organic pollutant that causes a range of syndromes including developmental toxicity. Dioxins have a high affinity for aryl hydrocarbon receptor (AhR) and induce cytochrome P4501A (CYP1A). However, the role of CYP1A activity in developmental toxicity is less clear. To better understand dioxin induced developmental toxicity, we exposed zebrafish (Danio rerio) embryos to PCB126 at concentrations of 0, 16, 32, 64, and 128 µg L(-1) from 3-h post-fertilization (hpf) to 168 hpf. The embryonic survival rate decreased at 144 and 168 hpf. The fry at 96 hpf displayed gross developmental malformations, including pericardial and yolk sac edema, spinal curvature, abnormal lower jaw growth, and non-inflated swim bladder. The pericardial and yolk sac edema rate significantly increased and the heart rate declined from 96 hpf compared with the controls. PCB126 did not alter the hatching rate. To elucidate the mechanism of PCB126-induced developmental toxicity, we conducted ethoxyresorufin-O-deethylase (EROD) in vivo assay to determine CYP1A enzyme activity, and real-time PCR to study the induction of CYP1A mRNA gene expression in embryo/larval zebrafish at 24, 72, 96, and 132 hpf. In vivo EROD activity was induced by PCB126 at 16 µg L(-1) concentration as early as 72 hpf but significant increases were observed only in zebrafish exposed to 64 and 128 µg L(-1) doses (p < 0.005) at 72, 96, and 132 hpf. Induction of CYP1A mRNA expression was significantly upregulated in zebrafish exposed to 32 and 64 µg L(-1) at 24, 72, 96, and 132 hpf. Overall, the severe pericardial and yolk sac edema and reduced heart rate suggest that heart defects are a sensitive endpoint, and the general trend of dose-dependent increase in EROD activity and induction of CYP1A mRNA gene expression provide evidence that the developmental toxicity of PCB126 to zebrafish embryos is mediated by activation of AhR.