Preparation and application of metal-modified biochar in the purification of micro-polystyrene polluted aqueous environment.

Microplastics (MPs) have already spread across the globe and have been found in drinking water and human tissues. This may pose severe threats to human health and water environment. Therefore, this study accurately evaluated the removal effect of metal-modified biochar on polystyrene microplastics (PS-MPs) (1.0 µm) in the water environment using a high-throughput fluorescence quantification method. The results indicated that Fe-modified biochar (FeBC) and Fe/Zn-modified biochar (Fe/ZnBC) had good removal efficiencies for PS-MPs under the dosage of 3 g/L, which were 96.24% and 84.77%, respectively. Although pore effects were observed (such as "stuck", "trapped"), the electrostatic interaction was considered the main mechanism for the adsorption of PS-MPs on metal-modified biochar, whereas the formation of metal-O-PS-MPs may also contribute to the adsorption process. The removal efficiency of PS-MPs by FeBC was significantly reduced under alkaline conditions (pH = 9 and 11) or in the presence of weak acid ions (PO43-, CO32-, HCO3-). A removal efficiency of 72.39% and 78.33% of PS-MPs was achieved from tap water (TW) and lake water (LW) using FeBC when the initial concentration was 20 mg/L. However, FeBC had no removal effect on PS-MPs in biogas slurry (BS) and brewing wastewater (BW) due to the direct competitive adsorption of high concentrations of chemical oxygen demand (COD). The findings of this study highlighted that metal-modified biochar had a potential application in purifying tap water or lake water which contaminated by MPs.

The Formation of Chitosan-Coated Rhamnolipid Liposomes Containing Curcumin: Stability and In Vitro Digestion.

There is growing interest in developing biomaterial-coated liposome delivery systems to improve the stability and bioavailability of curcumin, which is a hydrophobic nutraceutical claimed to have several health benefits. The curcumin-loaded rhamnolipid liposomes (Cur-RL-Lips) were fabricated from rhamnolipid and phospholipids, and then chitosan (CS) covered the surface of Cur-RL-Lips by electrostatic interaction to form CS-coated Cur-RL-Lips. The influence of CS concentration on the physical stability and digestion of the liposomes was investigated. The CS-coated Cur-RL-Lips with RL:CS = 1:1 have a relatively small size (412.9 nm) and positive charge (19.7 mV). The CS-coated Cur-RL-Lips remained stable from pH 2 to 5 at room temperature and can effectively slow the degradation of curcumin at 80 °C; however, they were highly unstable to salt addition. In addition, compared with Cur-RL-Lips, the bioavailability of curcumin in CS-coated Cur-RL-Lips was relatively high due to its high transformation in gastrointestinal tract. These results may facilitate the design of a more efficacious liposomal delivery system that enhances the stability and bioavailability of curcumin in nutraceutical-loaded functional foods and beverages.

Structures of a glucose-tolerant ß-glucosidase provide insights into its mechanism.

Cellulose can be converted to ethanol via the fermentation of glucose, which is considered as a promising green alternative for transportation fuels. The conversion of cellulose to glucose needs three enzymes, in which ß-glucosidase (BGL) plays an essential role. However, BGL is inhibited by its own product glucose, greatly limiting its applications in industry. We previously obtained a novel BGL named Bgl6 with a high glucose tolerance. Further engineering through random mutagenesis produced a triple mutant M3 with improved thermostability. This enzyme shows promising properties for wide applications but the structural basis of the unusual properties of Bgl6 is not clear. In this study, we determined the crystal structures of Bgl6 and variants at high resolution, which provide insights into its glucose-tolerant mechanism and thermostability. Particularly, Bgl6 forms an extra channel that could be used as a secondary binding site for glucose, which may contribute to glucose tolerance. Additionally, the triple mutations could strengthen the hydrophobic interactions within the enzyme and may be responsible for the enhanced thermostability exhibited by M3, which was further confirmed by dynamic light scattering data. Lastly, structural comparison to other orthologs allows us to formulate new strategies on how to improve the catalytic efficiency of Bgl6.

Synergistic effects of Fe-based nanomaterial catalyst on humic substances formation and microplastics mitigation during sewage sludge composting.

In this study, a novel Fe-based nanomaterial catalyst (Fe0/FeS) was synthesized via a self-heating process and employed to explore its impact on the formation of humic substances and the mitigation of microplastics. The results reveal that Fe0/FeS exhibited a significant increase in humic acid content (71.01 mg kg-1). Similarly, the formation of humic substances resulted in a higher humification index (4.91). Moreover, the addition of Fe0/FeS accelerated the degradation of microplastics (MPs), resulting in a lower concentration of MPs (9487 particles/kg) compared to the control experiments (22792 particles/kg). Fe0/FeS significantly increased the abundance of medium-sized MPs (50-200 µm) and reduced the abundance of small-sized (10-50 µm) and large-sized MPs (>1000 µm). These results can be attributed to the Fe0/FeS regulating the ▪OH production and specific microorganisms to promote humic substance formation and the degradation of MPs. This study proposes a feasible strategy to improve composting characteristics and reduce contaminants.

Simultaneously optimizing multiple properties of ß-glucosidase Bgl6 using combined (semi-)rational design strategies and investigation of the underlying mechanisms.

The performance of ß-glucosidase during cellulose saccharification is determined by thermostability, activity and glucose tolerance. However, conflicts between them make it challenging to simultaneously optimize three properties. In this work, such a case was reported using Bgl6-M3 as a starting point. Firstly, four thermostability-enhancing mutations were obtained using computer-aided engineering strategies (mutant M7). Secondly, substrate binding pocket of M7 was reshaped, generating two mutations that increased activity but decreased glucose tolerance (mutant M9). Then a key region lining active site cavity was redesigned, resulting in three mutations that boosted glucose tolerance and activity. Finally, mutant M12 with simultaneously improved thermostability (half-life of 20-fold), activity (kcat/Km of 5.6-fold) and glucose tolerance (ΔIC50 of 200 mM) was obtained. Mechanisms for property improvement were elucidated by structural analysis and molecular dynamics simulations. Overall, the strategies used here and new insights into the underlying mechanisms may provide guidance for multi-property engineering of other enzymes.

[Research Progress on Distribution Characteristics and Formation Mechanisms of Microplastics in the Environment].

The extensive application of plastic products leads to the increasingly significant harm of plastic wastes to the ecological environment, which is also a focus of global environmental issues. Due to the lack of a sound plastic waste management system, most plastic waste is still treated by the traditional mode or remains in the environment, with low recycling efficiency, and the plastic life cycle has not yet formed. Plastics in the environment will age and degrade under the actions of physical (wear, waves), chemical (ultraviolet radiation, hydrolysis), and biological (fungi, bacteria) factors for a long time and generate micro (nano) plastics. Due to their small particle size, large specific surface area, and charged characteristics, in addition to their own toxicity, they can also be used as carriers or covert carriers of pollutants (heavy metals, persistent organic pollutants, polycyclic aromatic hydrocarbons, bacteria, etc.) to migrate in the environment through runoff, sewage discharge, and hydrometeorology, causing ecological environmental pollution. MPs pollution has been listed as the second largest scientific problem in the field of environmental and ecological science by the United Nations Environment Programme. MPs are widely distributed, and there are different degrees of MPs pollution in the global water (freshwater, ocean), soil, and atmospheric environment. Traces of MPs have also been found in human placentas, human breastmilk, living lungs, and blood in recent years. Therefore, the formation mechanisms of MPs under the actions of physics, chemistry, and microorganisms, as well as their abundance levels and migration characteristics in water, soil, and atmosphere environment were comprehensively reviewed, with the hope of providing reference for monitoring the pollution levels of MPs in the environment, exploring their transport laws in the environment, proposing the management strategy of MPs pollution, and revealing the degradation mechanisms of MPs under different effects.

Harvesting Chlorella vulgaris by electro-flotation with stainless steel cathode and non-sacrificial anode.

As a promising method for efficiently harvesting microalgae, electro-flotation's performance is related to various factors including electrode design and process operating parameters. In this paper, bubble generation behavior on stainless-steel cathodes, with wire diameters of 0.8 mm, 0.2 mm and 0.05 mm, was studied. The results show that the bubble size increased with the increasing diameter of the electrode wire. Over 90 % harvesting efficiency was achieved using non-sacrificial anode. Extracellular polymeric substance is the main reason keeping bubbles from bursting.

Microwave catalytic co-pyrolysis of waste cooking oil and low-density polyethylene to produce monocyclic aromatic hydrocarbons: Effect of different catalysts and pyrolysis parameters.

It is promising to convert waste oil and plastics to renewable fuels and chemicals by microwave catalytic co-pyrolysis, enabling pollution reduction and resource recovery. The purpose of this study was to evaluate the effect of catalysts on the product selectivity of microwave-assisted co-pyrolysis of waste cooking oil and low-density polyethylene and optimize the pyrolysis process, including pyrolysis temperature, catalytic temperature, waste cooking oil to low-density polyethylene ratio, and catalyst to feedstocks ratio. The results indicated that catalysts had a great influence on the product distribution, and the yield of BTX (benzene, toluene, and xylenes), which increased in the following order: SAPO-34 < Hß < HY < HZSM-5. HZSM-5 was more active for the formation of light aromatic hydrocarbons as compared to others, where the concentrations of toluene, benzene and xylenes reached 252.59 mg/mL, 114.7 mg/mL and 132.91 mg/mL, respectively. The optimum pyrolysis temperature, catalytic temperature, waste cooking oil to low-density polyethylene ratio and catalyst to feedstocks ratio could be 550 °C, 450 °C, 1:1 and 1:2, respectively, to maximize the formation of BTX and inhibit the formation of polycyclic aromatic hydrocarbons.

Engineering of ß-Glucosidase Bgl15 with Simultaneously Enhanced Glucose Tolerance and Thermostability To Improve Its Performance in High-Solid Cellulose Hydrolysis.

In this study, a Petri-dish-based double-layer high-throughput screening method was established to improve glucose tolerance of ß-glucosidase Bgl15. Two beneficial mutations were identified, and the joint mutant 2R1 improved the half-maximal inhibitory concentration of glucose from 0.04 to 2.1 M. The crystal structure of 2R1 was subsequently determined at 2.7 Å. Structure analysis revealed that enhancement of glucose tolerance may be due to improved transglycosylation activity made possible by a hydrophobic binding site for glucose as an acceptor and more stringent control of a putative water channel. To further ameliorate the application potential of the enzyme, it was engineered to increase the half-life at 50 °C from 0.8 h (Bgl15) to 180 h (mutant 5R1). Furthermore, supplementation of 5R1 to the cellulase cocktail significantly improved glucose production from pretreated sugar cane bagasse by 38%. Consequently, this study provided an efficient approach to enhance glucose tolerance and generated a promising catalyst for cellulose saccharification.

A review on selective production of value-added chemicals via catalytic pyrolysis of lignocellulosic biomass.

Increasing fossil fuel consumption and global warming has been driving the worldwide revolution towards renewable energy. Biomass is abundant and low-cost resource whereas it requires environmentally friendly and cost-effective conversion technique. Pyrolysis of biomass into valuable bio-oil has attracted much attention in the past decades due to its feasibility and huge commercial outlook. However, the complex chemical compositions and high water content in bio-oil greatly hinder the large-scale application and commercialization. Therefore, catalytic pyrolysis of biomass for selective production of specific chemicals will stand out as a unique pathway. This review aims to improve the understanding for the process by illustrating the chemistry of non-catalytic and catalytic pyrolysis of biomass at the temperatures ranging from 400 to 650 °C. The focus is to introduce recent progress about producing value-added hydrocarbons, phenols, anhydrosugars, and nitrogen-containing compounds from catalytic pyrolysis of biomass over zeolites, metal oxides, etc. via different reaction pathways including cracking, Diels-Alder/aromatization, ketonization/aldol condensation, and ammoniation. The potential challenges and future directions for this technique are discussed in deep.

Microwave-assisted synthesis of bifunctional magnetic solid acid for hydrolyzing cellulose to prepare nanocellulose.

The conventional studies on the preparation of nanocellulose used a high concentration of sulfuric acid that is difficult to remove and recover. A biochar-based solid acid with magnetic properties was developed to hydrolyze cellulose to prepare nanocellulose in this work. Two different methods were selected to investigate the properties of the synthesized magnetic carbon-based solid acids. The synthesized catalysts were characterized by SEM, TEM, XRD, NH3-TPD and FT-IR. The experimental results showed that two solid acids by the microwave-assisted synthesis had good magnetic properties by a magnet adsorption. Analysis by SEM and TEM showed that the two solid acids had rich pore structures. According to mineral element analysis, both solid acids contained high sulfur content. The solid acid was an amorphous carbon structural material with a surface rich in active groups. The catalytic activity of the biochar-based solid acids in cellulose hydrolysis to prepare nano-scale cellulosic material was evaluated. It was found that magnetic biochar-based solid acid (MBC-SA1) could achieve a high yield, which produced up to 57.68% for hydrolyzing cellulose into nanometers.

Comparative study on characteristics of the bio-oil from microwave-assisted pyrolysis of lignocellulose and triacylglycerol.

Microwave-assisted pyrolysis of Camellia oleifera shell (COS) and stillingia oil (SO) was performed in the temperature range of 400-600 °C. The effects of feedstock and pyrolysis temperatures on product yield and bio-oil composition were discussed in detail. The bio-oil yield from COS pyrolysis varied from 37.30 wt% to 40.27 wt%, which was 11.32 wt% to 21.62 wt% lower than that from SO pyrolysis. Gas chromatography-mass spectrometry analysis indicated that SO bio-oil was rich in hydrocarbons, whereas COS pyrolysis produced mainly oxygen-containing compounds predominantly comprising phenols and acids. Fourier transform infrared and 1H-nuclear magnetic resonance spectra showed significant differences in the chemical structure of bio-oils from COS and SO pyrolysis. Elemental-composition and physical-property analyses further revealed that SO bio-oils were similar to gasoline and heavy fuel oil.

Microwave-assisted co-pyrolysis of lignin and waste oil catalyzed by hierarchical ZSM-5/MCM-41 catalyst to produce aromatic hydrocarbons.

Microwave-assisted catalytic fast co-pyrolysis (MACFP) of lignin and waste oil with SiC as microwave absorbent and hierarchical ZSM-5/MCM-41 as catalyst were implemented in a microwave-induced reactor. ZSM-5/MCM-41 is a kind of composite catalyst with MCM-41 as shell and ZSM as core. The effects of catalyst temperature, the ratio of feedstock-to-catalyst and the ratio of two reactants (lignin and waste oil) on product distribution and yield were studied. The study shows that catalytic co-pyrolysis is a complex reaction process, and many reaction conditions could affect the final reaction results. The optimum reaction conditions are as follows: catalytic temperature 400 °C, the feedstock-to-catalyst ratio of 10:1 and the ratio of lignin to waste oil of 2:1. Under this reaction condition, the conversion of feedstocks reached 76.00%, the proportion of aromatics was 50.31% and the selectivity of monocyclic aromatic hydrocarbons (MAHs) was 42.83%.

Lignocellulosic residue as bio-carrier for algal biofilm growth: Effects of carrier physicochemical proprieties and toxicity on algal biomass production and composition.

Five types of lignocellulosic materials were applied as the bio-carriers for low-cost algal biofilm cultivation of three algal strains. The effects of bio-carrier physicochemical properties and toxicity on algal cells growth and attachment were investigated. Rougher and hydrophilic bio-carrier could yield more algal biomass than smoother and hydrophobic bio-carrier. Pine sawdust (diameter: 0.420-0.595 mm) performed the best when cultured Diplosphaera sp. (9.61 g·m-2·day-1) biofilm. Meanwhile, bio-carriers could be leached by the culture medium during cultivation, and their energy conversion proprieties could be improved due to the reduced ash contents and the decreased crystallinities. In addition, Chlorella vulgaris growth tests indicated that pine sawdust (15.45%) leachate promoted cell growth, whereas rick husk (15.48%) and sugarcane bagasse (13.19%) leachate inhibited cell growth. And bio-carriers leachates also modified the chemical compositions (lipid, protein and carbohydrate) of algal cells and increased the corresponding saturated fatty acids methyl ester content (from 48.71 to 55.58-57.08%).

Bamboo (Phyllostachys pubescens) as a Natural Support for Neutral Protease Immobilization.

Lignin polymers in bamboo (Phyllostachys pubescens) were decomposed into polyphenols at high temperatures and oxidized for the introduction of quinone groups from peroxidase extracted from bamboo shoots and catalysis of UV. According to the results of FT-IR spectra analysis, neutral proteases (NPs) can be immobilized on the oxidized lignin by covalent bonding formed by amine group and quinone group. The optimum condition for the immobilization of NPs on the bamboo bar was obtained at pH 7.0, 40 °C, and duration of 4 h; the amount of immobilized enzyme was up to 5 mg g-1 bamboo bar. The optimal pH for both free NP (FNP) and INP was approximately 7.0, and the maximum activity of INP was determined at 60 °C, whereas FNP presented maximum activity at 50 °C. The Km values of INP and FNP were determined as 0.773 and 0.843 mg ml-1, respectively; INP showed a lower Km value and Vmax, than FNP, which demonstrated that INP presented higher affinity to substrate. Compared to FNP, INP showed broader thermal and storage stability under the same trial condition. With respect to cost, INP presented considerable recycling efficiency for up to six consecutive cycles.

Tat-Independent Secretion of Polyethylene Terephthalate Hydrolase PETase in Bacillus subtilis 168 Mediated by Its Native Signal Peptide.

Widespread utilization of polyethylene terephthalate (PET) has caused critical environmental pollution. The enzymatic degradation of PET is a promising solution to this problem. In this study, PETase, which exhibits much higher PET-hydrolytic activity than other enzymes, was successfully secreted into extracellular milieu from Bacillus subtilis 168 under the direction of its native signal peptide (named SPPETase). SPPETase is predicted to be a twin-arginine signal peptide. Intriguingly, inactivation of twin-arginine translocation (Tat) complexes improved the secretion amount by 3.8-fold, indicating that PETase was exported via Tat-independent pathway. To the best of our knowledge, this is the first report on the improvement of Tat-independent secretion by inactivating Tat components of B. subtilis 168 in LB medium. Furthermore, PET film degradation assay showed that the secreted PETase was fully active. This study paves the first step to construct an efficient engineered strain for PET degradation.

Microwave-assisted acid pretreatment of alkali lignin: Effect on characteristics and pyrolysis behavior.

This study performed microwave-assisted acid pretreatment on pure lignin. The effects of microwave temperature, microwave time, and hydrochloric acid concentration on characteristics and pyrolysis behavior of lignin were examined. Results of ultimate analysis revealed better properties of all pretreated samples than those of raw lignin. Fourier transform infrared spectroscopy analysis showed breakage of ßO4 bond and aliphatic side chain, decrease in OH groups, and formation of CO groups in pretreatment. Microwave temperature exerted more significant influence on lignin structure. Thermal stability of treated lignin was improved and insensitive to short microwave time and acid concentration under mild conditions. Resulting from improved alkyl-phenols and decreased alkoxy-phenols, microwave-assisted acid pretreatment of lignin yielded bio-oil with excellent quality. Total yield of phenols in pyrolysis vapors (200 °C) improved to 14.15%, whereas that of guaiacols decreased to 22.36%. This study shows that microwave-assisted acid pretreatment is a promising technology for lignin conversion.

Enhancing the Thermostability of Highly Active and Glucose-Tolerant ß-Glucosidase Ks5A7 by Directed Evolution for Good Performance of Three Properties.

A high-performance ß-glucosidase for efficient cellulose hydrolysis needs to excel in thermostability, catalytic efficiency, and resistance to glucose inhibition. However, it is challenging to achieve superb properties in all three aspects in a single enzyme. In this study, a hyperactive and glucose-tolerant ß-glucosidase Ks5A7 was employed as the starting point. Four rounds of random mutagenesis were then performed, giving rise to a thermostable mutant 4R1 with five amino acid substitutions. The half-life of 4R1 at 50 °C is 8640-fold that of Ks5A7 (144 h vs 1 min). Meanwhile, 4R1 had a higher specific activity (374.26 vs 243.18 units·mg-1) than the wild type with a similar glucose tolerance. When supplemented to Celluclast 1.5L, the mutant significantly enhanced the hydrolysis of pretreated sugar cane bagasse, improving the released glucose concentration by 44%. With excellent performance in thermostability, activity, and glucose tolerance, 4R1 will serve as an exceptional catalyst for industrial applications.

Fast microwave-assisted ex-catalytic co-pyrolysis of bamboo and polypropylene for bio-oil production.

The ex-catalytic co-pyrolysis of bamboo and polypropylene (PP) with HZSM-5 was investigated with microwave assistance. The influences of catalytic temperature, feedstock/catalyst ratio, and bamboo/PP ratio on the product yields and chemical components of bio-oil from the co-pyrolysis were studied. When the catalytic temperature, feedstock/catalyst ratio, and bamboo/PP ratio were 250 °C, 1:2, and 2:1, respectively, the bio-oil yield reached its maximum value at 61.62 wt%. The oxygenate proportion compounds decreased with increasing catalyst content. The PP addition improved the proportions of aromatics and naphthenic hydrocarbons. The bio-oil was upgraded significantly from the jet fuel perspective. A synergistic effect also existed between bamboo and PP.

Microwave-assisted co-pyrolysis of pretreated lignin and soapstock for upgrading liquid oil: Effect of pretreatment parameters on pyrolysis behavior.

The co-pyrolysis of pretreated lignin and soapstock was carried out to upgrade vapors under microwave irradiation. Results showed that the yield of 29.92-42.21 wt% of upgraded liquid oil was achieved under varied pretreatment conditions. Char yield decreased from 32.44 wt% for untreated control to 24.35 wt% for the 150 °C pretreated samples. The increased temperature, irradiation time and acid concentration were conducive to decrease the relative contents of phenols and oxygenates in liquid oils. The main components of the liquid oil were gasoline fraction (mono-aromatics and C5-C12 aliphatics), which ranged from 57.38 to 71.98% under various pretreatment conditions. Meanwhile, the diesel fraction (C12+ aliphatics) ranged from 13.16 to 22.62% from co-pyrolysis of pretreated lignin and soapstock, comparing with 10.18% of C12+ aliphatics from co-pyrolysis of non-pretreated lignin and soapstock. A possible mechanism was proposed for co-pyrolysis of pretreated lignin and soapstock for upgraded liquid oils.