Epoxy monomers derived from tung oil fatty acids and its regulable thermosets cured in two synergistic ways.

A novel biobased epoxy monomer with conjugated double bonds, glycidyl ester of eleostearic acid (GEEA) was synthesized from tung oil fatty acids and characterized by (1)H and (13)C NMR. Differential scanning calorimeter analysis (DSC) and Fourier transform infrared spectroscopy (FT-IR) were utilized to investigate the curing process of GEEA with dienophiles and anhydrides. DSC indicated that GEEA could cross-link with both dienophiles and anhydrides through Diels-Alder reaction and epoxy/anhydride ring-opening reaction. Furthermore, Diels-Alder cross-link was much more active than the ring-opening of epoxy and anhydride in the curing process. FT-IR also revealed that GEEA successively reacted with dienophiles and anhydrides in both cross-linking methods. Dynamic mechanical analysis and mechanical tensile testing were used to study the thermal and mechanical properties of GEEA cured by maleic anhydride, nadic methyl anhydride and 1,1'-(methylenedi-4,1-phenylene)bismaleimide. Due to the independence between the curing agents, dienophile and anhydride, a series of thermosetting polymers with various properties could be obtained by adjusting the composition of these two curing agents.

Developing acrylated epoxidized soybean oil coating for improving moisture sensitivity and permeability of starch-based film.

Acrylated epoxidized soybean oil (AESO)-based coatings were developed to reduce moisture sensitivity and permeability of starch-based materials. The coating was applied on starch based films by dipping the samples on AESO-based coating solutions, followed by crosslinking with ultraviolet (UV) light. Effect of AESO concentration, photoinitiator content and processing conditions on the performance of coated starch-based film was systematically investigated, in particular the effect of coating on moisture absorption, permeability and mechanical properties. The modified surface was characterized by scanning electronic microscopy and Fourier transform infrared spectroscopy. The results showed that the moisture sensitivity of the starch-based sheets was reduced significantly since the crosslinked AESO acted as a hydrophobic layer. Moisture permeability was decreased more than 10 times after AESO treatment. It was found that the crosslinking density acted as one of the key factors, so even a very thin layer of AESO could achieve good water resistance.

"Green" composites from renewable resources: preparation of epoxidized soybean oil and flax fiber composites.

In recent years there has been considerable interest in using natural plant fibers as reinforcements for plastics. The motivation includes cost, performance enhancement, weight reduction, and environment concerns. High performance flax fiber could potentially substitute for glass or carbon fibers as reinforcements for plastics. This study reports the "green" composites obtained from a mixture of epoxidized soybean oil and epoxy resin, 1,1,1-tris(p-hydroxyphenyl)ethane triglycidyl ether (THPE-GE), reinforced with flax fiber. The compression molding method is used for making the composites. Curing agents triethylenetetramine and diethylenetriamine provide better physical properties of the composites than Jeffamine agents D-230 and EDR-148. Both the flexural modulus and the tensile modulus of the composites increase as the amount of THPE-GE increases. The flexural modulus increased at a fiber content of <10 wt %, but there is a decrease beyond 10 wt %. The tensile modulus increases with fiber content until a maximum at 13.5 wt %, and then it decreases. The flax fiber length affected the mechanical properties of the composites: the longer the fiber length, the better are the mechanical properties observed.

Microwave-assisted synthesis of cyclodextrin polyurethanes.

Cyclodextrin (CD) has often been incorporated into polyurethanes in order to facilitate its use in encapsulation or removal of organic species for various applications. In this work a microwave-assisted method has been developed to produce polyurethanes consisting of α-, ß-, and γ-CD and three common diisocyanates. As compared to conventional heating, this new synthetic method saves energy, significantly reduces reaction time, and gets similar or improved yield. The reaction products have been fully characterized with (13)C, (1)H, and two-dimensional NMR spectroscopy. With suitable stoichiometry of starting CD and diisocyanate, the resulting CD polyurethane is organic-soluble and water-insoluble and is shown to remove Nile red dye and phenol from water. Possible applications include the removal of undesirable materials from process streams, toxic compounds from the environment, and encapsulation of color or fragrance molecules.

From oligomers to molecular giants of soybean oil in supercritical carbon dioxide medium: 1. Preparation of polymers with lower molecular weight from soybean oil.

Polymers with a low molecular weight derived from soybean oil have been prepared in a supercritical carbon dioxide medium by cationic polymerization. Boron trifluoride diethyl etherate was used as an initiator. Influences of polymerization temperature, amount of initiator, and carbon dioxide pressure on the molecular weight were investigated. It is shown that the higher polymerization temperature favors polymers with relatively higher molecular weights. Larger amounts of initiator also provide polymers with higher molecular weights. Higher pressure favors polymers with relatively higher molecular weights. The applications of these soy-based materials will be in the lubrication and hydraulic fluid areas.

A new polymer-lipid hybrid nanoparticle system increases cytotoxicity of doxorubicin against multidrug-resistant human breast cancer cells.

PURPOSE: This work is intended to develop and evaluate a new polymer-lipid hybrid nanoparticle system that can efficiently load and release water-soluble anticancer drug doxorubicin hydrochloride (Dox) and enhance Dox toxicity against multidrug-resistant (MDR) cancer cells. METHODS: Cationic Dox was complexed with a new soybean-oil-based anionic polymer and dispersed together with a lipid in water to form Dox-loaded solid lipid nanoparticles (Dox-SLNs). Drug loading and release properties were measured spectrophotometrically. The in vitro cytotoxicity of Dox-SLN and the excipients in an MDR human breast cancer cell line (MDA435/LCC6/MDR1) and its wild-type line were evaluated by trypan blue exclusion and clonogenic assays. Cellular uptake and retention of Dox were determined with a microplate fluorometer. RESULTS: Dox-SLNs were prepared with a drug encapsulation efficiency of 60-80% and a particle size range of 80-350 nm. About 50% of the loaded drug was released in the first few hours and an additional 10-20% in 2 weeks. Treatment of the MDR cells with Dox-SLN resulted in over 8-fold increase in cell kill when compared to Dox solution treatment at equivalent doses. The blank SLN and the excipients exhibited little cytotoxicity. The biological activity of the released Dox remained unchanged from fresh, free Dox. Cellular Dox uptake and retention by the MDR cells were both significantly enhanced (p < 0.05) when Dox was delivered in Dox-SLN form. CONCLUSIONS: The new polymer-lipid hybrid nanoparticle system is effective for delivery of Dox and enhances its efficacy against MDR breast cancer cells.