Cellulose-Acetate Coating by Integrating Ester Group with Zinc Salt for Dendrite-Free Zn Metal Anodes.

Zinc (Zn) metal is considered a potential anode owing to its high theoretical capacity, safety, and low cost. However, the dendrites and corresponding side reactions in aqueous electrolytes hinder their further development in environmentally-friendly energy storage. Herein, ion-affiliative cellulose acetate (CA) coating with Zn(CF3 SO3 )2 is constructed on Zn anode (CAZ@Zn). Owing to the complexation effect between the polar ester group (CO) and Zn salt (Zn2+ ), the CAZ polymer coating enhances the hydrophilicity of the Zn anode and reduces the interfacial resistance, allowing the rapid Zn2+ diffusion and homogenizing the Zn deposition in an aqueous electrolyte to suppress zinc dendrite formation and growth. Therefore, the symmetric CAZ@Zn//CAZ@Zn battery achieves reversible plating/stripping over 2800 h at 1 mA cm-2 with 1 mAh cm-2 , about sevenfold higher than bare Zn. The full cell fabricated with an optimized Zn anode and the NH4 V4 O10 cathode achieves substantially stable performance, superior to that of bare Zn. This work provides a straightforward, effective, and scalable method to suppress the zinc dendrites and corresponding side reactions for aqueous Zn-ions batteries.

A New Type of Quartz Smog Chamber: Design and Characterization.

Since the 1960s, many indoor and outdoor smog chambers have been developed worldwide. However, most of them are made of Teflon films, which have relatively high background contaminations due to the wall effect. We developed the world's first medium-size quartz chamber (10 m3), which is jointed with 32 pieces of 5 mm thick polished quartz glasses and a stainless-steel frame. Characterizations show that this chamber exhibits excellent performance in terms of relative humidity (RH) (2-80%) and temperature (15-30 ± 1 °C) control, mixing efficiency of the reactants (6-8 min), light transmittance (>90% above 290 nm), and wall loss of pollutants. The wall loss rates of the gas-phase pollutants are on the order of 10-4 min-1 at 298 K under dry conditions. It is 0.08 h-1 for 100-500 nm particles, significantly lower than those of Teflon chambers. The photolysis rate of NO2 (JNO2) is automatically adjustable to simulate the diurnal variation of solar irradiation from 0 to 0.40 min-1. The inner surface of the chamber can be repeatedly washed with deionized water, resulting in low background contaminations. Both experiments (toluene-NOx and α-pinene-ozone systems) and box model demonstrate that this new quartz chamber can provide high-quality data for investigating SOA and O3 formation in the atmosphere.

Effect of spraying on coal dust diffusion in a coal mine based on a numerical simulation.

Aimed at effectively controlling coal dust pollution in the mining face of a coal mine, this study first conducted a theoretical analysis and then combined a spraying experiment and a numerical simulation to perform an in-depth examination of the atomizing characteristics and dust suppression performance of a coal cutter external spraying device. Based on the experimental spraying results, the optimal nozzle was determined to be a pressure round-mouth nozzle with an X-shaped core. The characteristics of the spray fields from nozzles of different calibers (1.6, 2.0 and 2.4 mm) at different spraying pressures (2, 4, 6 and 8 MPa) were then analyzed. It was found that the droplet concentration in the spray field increased with increasing spraying pressure and nozzle caliber. The droplet diameter was mainly dependent on the spraying pressure and varied more slowly with increased spraying pressure. At a spraying pressure of 8 MPa, the spray field formed could achieve effective dust suppression; specifically, the droplet concentration in the spray field was mostly more than 15 g/m3, and the droplet size was mainly distributed in the range of 30-100 µm. When using a 2.4 mm caliber nozzle, the dust concentration measured around the coal cutter operator was reduced to 87.21 mg/m3 under a spraying pressure of 8 MPa, suggesting adequate dust suppression.