RESUMO
This study aimed to evaluate the influence of radiotherapy and different endodontic treatment protocols on the bond strength to pulp chamber dentin. Eighty mandibular molars were randomly divided into two groups (n = 40): non-irradiated and irradiated (60 Gy). The pulp chambers were sectioned, and each group was subdivided (n = 8), according to the endodontic treatment protocol: no treatment (Control); Single-visit; Two-visits; Immediate dentin sealing (IDS) + single-visit; and IDS + two-visits. Each endodontic treatment visit was simulated through irrigation with 2.5% NaOCl, 17% EDTA and distilled water. IDS was performed by actively applying two coats of a universal adhesive to the lateral walls of the pulp chamber. After, the pulp chambers were restored with resin composite and four sticks were obtained for microtensile test. In addition, the dentin of the pulp chamber roof was assessed for surface roughness, chemical composition, and topography after each treatment protocol. Two-way ANOVA, Tukey's post hoc, Mann-Whitney, Kruskal-Wallis and Dunn's post hoc were performed (α = 5%). The treatment protocol affected bond strength (p < 0.05), while the irradiation did not (p > 0.05). The control group presented the highest values (p < 0.05). The single-visit group demonstrated better performance compared to the other groups (p < 0.05), which did not differ from each other (p > 0.05) The use of IDS changed the surface roughness (p < 0.05), chemical composition (p < 0.05) and topography of the dentin. In conclusion, the treatment protocol influenced dentin adhesion, while irradiation did not.
RESUMO
STATEMENT OF PROBLEM: The influence of computer-aided manufacturing (CAM) parameters and settings on the outcomes of milled indirect restorations is poorly understood. PURPOSE: The purpose of this scoping review was to summarize the current CAM systems, parameters, and setting changes, and their effects on different outcomes of milled indirect restorations and aspects related to their manufacture. MATERIAL AND METHODS: The protocol of this review is available online (https://osf.io/x28ps/). Studies that used at least 2 different parameters (CAM units, number of axes, digital spacers, or protocols with different rotatory instruments, grit-sizes, milling speed, or others) for milling indirect restorations were included. A structured search up to July 2023 was performed by 2 independent reviewers for articles written in English in LILACS, MEDLINE via PubMed, EMBASE, Web of Science, and Scopus. RESULTS: Of 1546 studies identified, 22 were included in the review. Discrepancies were found between the planned and actual measured cement space, with a decreasing linear relationship impacting restoration adaptation at different points. The CEREC MC XL milling machine was the most used system in the included studies, with variations in bur types, milling modes, and number of burs uses affecting internal fit and surface trueness. The results demonstrated the better adaptation of restorations made with 5-axis over 3-axis milling machines. Lithium disilicate and zirconia were the most commonly used materials, and crowns and inlays were popular designs. Marginal and internal adaptation were the primary outcomes assessed using the various techniques. CONCLUSIONS: The study presented a comprehensive exploration of CAM systems and parameters, and their influence on indirect restorations. The planned cement space was not properly reproduced by the milling. Bur characteristics can affect restoration fit and trueness. The 5-axis units seem to result in better-adapted restorations compared with 3- and 4-axis units.
Assuntos
Desenho Assistido por Computador , Planejamento de Prótese Dentária , Humanos , Planejamento de Prótese Dentária/métodos , Restauração Dentária Permanente/métodos , Adaptação Marginal DentáriaRESUMO
OBJECTIVES: To evaluate the longevity of metal-ceramic single crowns cemented onto resin composite prosthetic cores using a self-adhesive resin cement in a prospective clinical descriptive study. METHODS: A total of 152 teeth were endodontically treated and received resin composite prosthetic cores and metal-ceramic crowns cemented with a self-adhesive resin cement. The patients included in the sample were recalled for clinical and radiography evaluation in an up-to-106-month period after the final cementation procedures, with an average of 62 months of follow-up. 91.5% of the sample (142 teeth) were evaluated regarding the treatment survival rate, analyzed considering the loss of crown retention (crown debonding) and tooth loss as the primary outcome. In addition, post debonding, and root fracture occurrences were also recorded as secondary outcomes to evaluate the success rate of the prosthetic treatment. The aesthetic parameters were also evaluated according to the FDI criteria. The Kaplan-Meier method and Cox regression with 95% confidence interval were applied for the statistical analysis. RESULTS: Regarding the primary outcome, the metal-ceramic crowns cemented with self-adhesive resin cement presented a high survival rate (91.5%), with 8 crown debondings and 3 tooth losses (1 due to caries and 2 due to periodontal disease) occurring after the evaluation period. For secondary outcomes, 9 root fractures and 4 post debondings occurred, generating a success rate of 72%. All crowns had a score 1 on the FDI criteria, indicating that they were clinically excellent or very good regarding the aesthetic parameters. CONCLUSION: The metal-ceramic crowns luted with a self-adhesive resin cement presented a survival rate of 91.5% after an average of 62 months of follow-up. Furthermore, the restorations remained aesthetically satisfactory over time, without changes that would indicate prosthetic retreatment. A success rate of 72% was obtained considering the secondary outcome, mainly related to intraradicular retainer failures (root fractures or post debonding). CLINICAL SIGNIFICANCE: The self-adhesive resin cement is clinically indicated for cementation of metal-ceramic crowns onto resin composite prosthetic cores.
Assuntos
Cimentos Dentários , Cimentos de Resina , Humanos , Seguimentos , Estética Dentária , Resinas Compostas , Coroas , Cimentação/métodos , Cerâmica , Teste de Materiais , Falha de Restauração DentáriaRESUMO
OBJECTIVES: The objective of this study is to evaluate the longevity of two fiber post cementation strategies in a prospective, multicenter, non-inferiority, double-blind randomized controlled trial. METHODS: A total of 152 teeth, with adequate endodontic treatment and loss of coronal structure and bilateral simultaneous posterior occlusal contacts, were randomly allocated to receive glass fiber posts cemented with a conventional cementation strategy (CRC group: adhesive system + resin cement) (Adper Single Bond + RelyX ARC; 3 M-ESPE) or a self-adhesive cementation strategy (SRC group: self-adhesive resin cement; RelyX U100/U200; 3 M-ESPE). The patients were recalled annually for clinical and radiographical evaluation with a 93% recall rate (142 teeth, with 74 at CR groups and 68 at SRC group). The primary outcome was survival rate, considering the fiber post debonding (loss of retention). The secondary outcome included the success rate of the prosthetic treatment with crown debonding, post fracture, and tooth loss (not related to post failure). Both outcomes were evaluated annually. The Kaplan-Meier method and Cox regression with 95% confidence interval were used for the statistical analysis. RESULTS: For the primary outcome (failures directly related to fiber posts cementation strategy), there were 4 fiber post debondings (2 per group), 8 root fractures (3 for SRC group and 5 for CRC group), and one mixed failure (debonding combined with root fracture for CRC), with both strategies presenting similar survival rates (p = 0.331), with 88.9% for the CRC group and 90.9% for the SRC group. For the secondary outcome (failures not related to fiber post cementation strategies), there were 8 crown debondings, 3 post fractures, and 3 tooth losses, with no statistically difference between groups (p = 0.701), with 77% for SRC and 82% for CRC. CONCLUSION: Fiber post cementation strategies with conventional or self-adhesive resin cement presents similar tooth survival and success rates. TRIAL REGISTRATION: NCT01461239 CLINICAL RELEVANCE: Both adhesive cementation strategies led to high survival and success rates and are indicated for fiber post cementation, even after a long follow-up period (up to 106 months).
Assuntos
Colagem Dentária , Técnica para Retentor Intrarradicular , Humanos , Cimentos de Resina/química , Cimentação/métodos , Cimentos Dentários/química , Taxa de Sobrevida , Estudos Prospectivos , Vidro/química , Teste de Materiais , Análise do Estresse Dentário , DentinaRESUMO
OBJECTIVES: This study evaluated the effect of deep margin elevation (DME) and restorative materials (leucite-reinforced glass-ceramics [C] vs. indirect resin composite [R]) on the fatigue behavior and stress distribution of maxillary molars with 2-mm deep proximal margins restored with MOD inlay. METHODS: Fifty-two extracted human third molars were randomly assigned into four groups (n = 13): C; DME + C; R; and DME + R. Inlays were fabricated in CAD-CAM and bonded to all teeth. The fatigue behavior was assessed with the stepwise stress test (10,000 cycles/step; step = 50 N; 20 Hz; initial load = 200 N). Fatigue failure loads and the number of cycles were analyzed with 2-way ANOVA and Tukey's test (p < 0.05) and Kaplan-Meier survival plots. The stress distribution was assessed with finite element analysis. The models were considered isotropic, linear, and homogeneous, and presented bonded contacts. A tripod axial load (400 N) was applied to the occlusal surface. The stress distribution was analyzed with the maximum principal stress criterion. RESULTS: For fatigue, there was no difference for DME factor (p > 0.05). For the material factor, the load and number of cycles for failure were statistically higher in the R groups (p < 0.05). The finite element analysis showed that resin composite inlays concentrated more stress in the tooth structure, while ceramic inlays concentrated more stress in the restoration. Non-reparable failures were more frequent in the resin composite inlays groups. CONCLUSIONS: DME was not negative for fatigue and biomechanical behaviors. Resin composite inlays were more resistant to the fatigue test, although the failure mode was more aggressive. CLINICAL SIGNIFICANCE: DME does not impair mechanical behavior. Resin composite inlays failed at higher loads but with a more aggressive failure mode.
Assuntos
Porcelana Dentária , Restaurações Intracoronárias , Resinas Compostas/química , Porcelana Dentária/química , Análise do Estresse Dentário , Humanos , Teste de Materiais , Dente Molar , Estresse MecânicoRESUMO
To evaluate the effect of acidic challenge on erosion depth and topographic characteristics of different materials used as occlusal sealants. Two hundred specimens of five sealant materials (Fuji IX, Ketac Molar, Fuji II, Equia and Clinpro) and forty bovine teeth enamel samples (control) were prepared and exposed to acidic challenge. The specimens were immersed in four different solutions (orange juice, coke drink, citric acid or distilled water) under mildly shaken conditions for 3 days. The erosion depth profiles were measured using a profilometer and Scanning Electron Microscope (SEM). Two-way ANOVA with Tukey post-hoc test was performed to evaluate the interactions. Sealant material and acidic challenge had significant effects on erosion depth. Among the materials, Fuji II presented the highest mean of erosion depth after immersion in orange juice, coke drink, and citric acid. All materials groups presented higher erosion depth values after immersion in the citric acid solution, except Clinpro. Bovine enamel presented higher erosion depth values compared to all materials when submitted to erosive challenge. Sealant materials submitted to the acidic challenge presented different degrees of erosion and topographic modification; however, they are less susceptible to erosion than bovine teeth enamel.
Assuntos
Ácido Cítrico , Esmalte Dentário , Teste de Materiais , Microscopia Eletrônica de Varredura , Selantes de Fossas e Fissuras , Propriedades de Superfície , Erosão Dentária , Bovinos , Animais , Erosão Dentária/prevenção & controle , Erosão Dentária/induzido quimicamente , Esmalte Dentário/efeitos dos fármacos , Selantes de Fossas e Fissuras/química , Análise de Variância , Fatores de Tempo , Propriedades de Superfície/efeitos dos fármacos , Cimentos de Ionômeros de Vidro/química , Cimentos de Ionômeros de Vidro/uso terapêutico , Reprodutibilidade dos Testes , Bebidas Gaseificadas/efeitos adversos , Valores de Referência , Concentração de Íons de Hidrogênio , Resinas Compostas/químicaRESUMO
The aim of this study was to mechanically characterize through flexural fatigue test two CAD-CAM glass-ceramics according to distinct surface etching protocols. To do so, feldspathic (FELD) and lithium disilicate (LD) glass ceramics were subjected to different surface treatments: (1) control - no treatment (Ctrl); (2) conventional protocol etching with 5% hydrofluoric acid followed by silane coupling agent application (HF + SIL; Monobond N, Ivoclar); or (3) using a self-etching ceramic primer (E&P; Monobond Etch & Prime, Ivoclar). Ceramic discs (N = 120; Ø = 12 mm; thickness = 1.2 mm) were produced from CAD-CAM blocks, with 60 being from FELD (VITABLOCS Mark II, Vita Zahnfabrik) and 60 from LD (IPS e.max CAD, Ivoclar). Next, 20 disks of each ceramic were allocated into three groups: Ctrl, HF + SIL, or E&P. Surface roughness data were collected on all samples before and after surface treatments (except for Ctrl). Cyclic fatigue (n = 15) biaxial flexural strength tests were performed by the piston-on-three-balls geometry (ISO 6872) considering the test parameters established from a monotonic test (n = 5). The monotonic test was carried out at a 1 mm/min loading rate and 500 kgf loading cell until fracture to obtain the failure data. The cyclic fatigue test was executed underwater at a frequency up to 20 Hz, with the first stress being 25% of the monotonic test for 5000 cycles, followed by increments of 5% of the monotonic test at each step of 10,000 cycles until failure (fracture). Complementary fractography, topography and Atomic Force Microscopy (AFM) analyses were performed. Characteristic Fatigue Strength (CFS) and Weibull modulus were analyzed by Weibull analysis using the fatigue test data. Roughness and complementary analysis data were analyzed by one-way ANOVA. The statistical results exhibited similar CFS among Ctrl, HF + SIL and E&P for both glass-ceramics. The survival analysis corroborates the findings, however the Weibull modulus pointed out superior structural reliability of FELD treated with the E&P group compared to HF + SIL. According to the complementary analyses, HF + SIL exhibited a higher surface area than E&P and Ctrl for FELD (p = 0.001). Roughness showed statistically significant differences among conditions for FELD (E&P < Ctrl = HF + SIL; p < 0.05) and no difference for LD (p > 0.05). Therefore, the CFS were not influenced by any condition evaluated for FELD and LD glass-ceramics; however, superior structural reliability (higher Weibull modulus) for the feldspathic ceramic treated with the E&P was observed.
Assuntos
Colagem Dentária , Silanos , Propriedades de Superfície , Silanos/química , Ácido Fluorídrico , Reprodutibilidade dos Testes , Teste de Materiais , Condicionamento Ácido do Dente , Cerâmica/química , Porcelana Dentária , Análise do Estresse Dentário , Cimentos de ResinaRESUMO
OBJECTIVES: Gerontological education and intergenerational contact are proven strategies for effectively combating ageism. In this context, this study investigates the association between gerontological education, intergenerational contact, and ageism among dental students. METHODS: Gerontological education from students' perspective, intergenerational contact, and ageism were assessed using a questionnaire containing sociodemographical aspects and an ageism scale (ASDS-Braz). The sample included students enrolled in the final year of dental programs at three public universities in southern Brazil. A multilevel Poisson regression was conducted to assess factors associated with ASDS-Braz scores. RESULTS: A modest correlation was identified between dental schools in terms of reducing ageism, and a weak correlation was found between self-reported race and ageism. Notably, statistically significant findings were observed across family relationship with older individuals: students who reported having a poor relationship with older adults in their families presented 45% higher ageism scores than did those with an excellent relationship. CONCLUSION: The results suggested that while some gerontological education was reported by the participants, it may not be sufficient to prepare dental students to provide effective oral healthcare to older adults and to reduce ageism among them. Additionally, reinforcing positive aspects of intergenerational relationships may be an additional strategy in combating ageism within this population.
RESUMO
This study aimed to evaluate the fatigue performance of simplified ceramic restorations (leucite-reinforced glass ceramic) adhesively cemented onto substrates of different resin composites. Three options from the same commercial line were selected (Tetric N-Line, Ivoclar), classified as Conventional (CRC), Bulk-fill (BRC) and Flowable (FRC), which were used to make discs using a cylindrical metallic device (n = 19; Ø = 10 mm, thickness = 2.0 mm). A total of 57 discs (Ø = 10 mm, thickness = 1.0 mm) were made from CAD/CAM prefabricated blocks of a leucite reinforced glass-ceramic (Empress CAD, Ivoclar) to simulate a monolithic restoration, then were randomly distributed to be bonded on 19 discs of each three different resin composite substrates (CRC; BRC; or FRC) with a dual resin cement (Multilink N; Ivoclar). The samples were subjected to a compression test with a hemispherical stainless-steel piston (Ø = 40 mm) at a monotonic regimen (n = 4; 1 mm/min loading rate and 500 kgf loading cell until fracture). The cyclic fatigue test was performed underwater at a frequency of 20 Hz (n = 15). The first step was applied using 200N for 5000 cycles, followed by increments of 50N at each step of 10,000 until failure. The outcome considered for both tests was the occurrence of radial crack. Specific statistical tests (α = 0.05) were performed for monotonic (One-way ANOVA; Tukey's test) and fatigue data (Kaplan-Meier test; Log-rank test). Fractography of fractured samples were also performed. The FRC group had the lowest failure load in both test regimes (p < 0.05; monotonic: 726.64N; fatigue: 716.67N). There were no differences between the CRC and BRC groups (p > 0.05; monotonic: 989.30 and 990.11N; fatigue: 810.00 and 833.33N, respectively). The same result was obtained considering cycles for fatigue failure (FRC < CRC=BRC). Leucite glass-ceramic bonded to substrates made of flowable resin composite behaves worse mechanically than bonding to conventional or bulk-fill resin composite substrates.
Assuntos
Silicatos de Alumínio , Cerâmica , Desenho Assistido por Computador , Propriedades de Superfície , Teste de Materiais , Suporte de Carga , Análise do Estresse Dentário , Porcelana Dentária , Falha de Restauração DentáriaRESUMO
The aim of this in vitro study was to evaluate the effect of the combinations of two different intraoral scanners (IOS), two milling machines, and two restorative materials on the marginal/internal fit and fatigue behavior of endocrowns produced by CAD-CAM. Eight groups (n= 10) were considered through the combination of TRIOS 3 (TR) or Primescan (PS) IOS; 4-axes (CR; CEREC MC XL) or 5-axes (PM; PrograMill PM7) milling machines; and lithium disilicate (LD; IPS e.max CAD) or resin composite (RC; Tetric CAD) restorative materials. Specific surface treatments were applied to each material, and the bonding to its corresponding Endocrown-shaped fiberglass-reinforced epoxy resin preparations was performed (Variolink Esthetic DC). Computed microtomography (µCT) was performed to assess the marginal/internal fit, as well as a mechanical fatigue test (20 Hz, initial load = 100 N/5000 cycles; step-size = 50 N/10,000 cycles until a threshold of 1500 N, then, the step-size was increased if needed to 100 N/10,000 cycles until failure or a threshold of 2800 N) to evaluate the restorations long-term behavior. Complementary analysis of the fracture features and surface topography in scanning electron microscopy was performed. Three-way ANOVA and Kaplan-Meier test (α = 0.05) were performed for marginal/internal fit, and fatigue behavior data, respectively. PS scanner, CR milling machine, and RC endocrowns resulted in a better marginal fit compared to their counterparts. Still, the PM machine resulted in a better pulpal space fit compared to the CR milling machine. Regardless of the scanner and milling machine, RC endocrowns exhibited superior fatigue behavior than LD ones. LD endocrowns presented margin chipping regardless of the milling machine used. Despite minor differences in terms of fit, the 'IOS' and 'milling machine' factors did not impair the fatigue behavior of endocrowns. Resin-composite restorations resulted in a higher survival rate compared to glass-ceramic ones, independently of the digital devices used in the workflow.
Assuntos
Resinas Compostas , Desenho Assistido por Computador , Porcelana Dentária , Teste de Materiais , Resinas Compostas/química , Porcelana Dentária/química , Fenômenos Mecânicos , Propriedades de Superfície , Testes Mecânicos , Estresse MecânicoRESUMO
This in vitro study assessed the effectiveness of three cleaning protocols (air-water spray, 37% phosphoric acid, or Ivoclean) on lithium disilicate restorations' fatigue behavior after try-in paste application, compared to a clean condition. Lithium disilicate discs (IPS e.max CAD, Ivoclar) with Ø-= 12 mm and 1 mm thickness were prepared from prefabricated CAD-CAM blocks, polished, subjected to CAD-CAM milling topography simulation and crystallization. After, etching with 5% hydrofluoric acid and the application of try-in paste (Variolink try-in paste shade white; load of 2.5 N for 5 min) was performed. Discs that received try-in paste were divided into three groups according to the removal protocol: SPRAY - air-water spray for 30 s; HPO - active application of 37% phosphoric acid for 60 s; IVOC - application of Ivoclean for 20 s. Control group (CTRL group) did not receive the try-in paste application. Half of the specimens (n= 15) were tested in the baseline condition (24 h up to 7 days), and the others underwent 25,000 thermal cycles (5 - 55 °C) + 210 days of distilled water storage (37 °C). Additional specimens (n= 3) underwent monotonic testing (1 mm/min). Fatigue testing involved a cyclic fatigue approach (20 Hz, initial load = 100 N - 5000 cycles, step size = 50 N - 10,000 cycles) until a visible crack appeared. Fractographic and topographic analyses were performed. Fatigue data were statistically analyzed with two-way ANOVA, Kaplan-Meier log-rank (Mantel-Cox), and independent t-test (α= 0.05). In the baseline condition, the IVOC group resulted in a superior fatigue behavior compared to the CTRL and SPRAY groups, but similar to the HPO group. The HPO and SPRAY presented a similar fatigue behavior to the CTRL group. It was noticed a decrease in fatigue behavior after aging, which resulted in all the cleaning protocols leading to similar fatigue behavior compared to the CTRL group. On the SPRAY group surface, try-in pastes remnants were noticed. In summary, despite a detrimental impact at baseline conditions, all tested cleaning protocols seem proper to remove the try-in paste from the ceramic's surface in the long-term evaluation.
Assuntos
Cerâmica , Porcelana Dentária , Ácidos Fosfóricos , Propriedades de Superfície , Teste de Materiais , Cerâmica/química , Desenho Assistido por Computador , Água , Análise do Estresse DentárioRESUMO
The characteristics of dental ceramics have been extensively studied over the years to provide highly qualified materials for use in prosthetic restorations. The ability to adhere to dental substrates, outstanding aesthetics (translucency, color, and substrate masking ability) and improved mechanical properties provide these materials with optical features and high strength to withstand masticatory stimuli. Different classifications are adopted, and it is generally considered that glass-ceramics have better optical characteristics due to the high glass content, and polycrystalline ceramics have superior strength favored by their densified and organized crystals, hampering crack growth. This knowledge was largely built-up during years of scientific research through different testing methodologies, but mainly employing static loads. It is important to not only take into account the intensity of loads that these materials will be exposed to, but also the effect of the intermittence of cyclic load application leading to mechanical fatigue and the influence of factors related to the crack origin and their propagation under this condition. Furthermore, the bonding surface of ceramic restorations requires surface treatments that improve the bond strength to luting agents; however, these treatments require caution because of their potential to produce defects and affect the structural behavior. Moreover, ceramic restorations often require internal adjustments for proper seating or external adjustments for fitting the occlusal contact with the antagonist. In this sense, finishing/polishing protocols may alter the defect population, as luting agents may also interact by filling in the superficial defects on the restoration intaglio surface. Thus, the balance among all these factors will define the performance of a restorative setup, as well as the posterior exposure to the humid environment and the masticatory stimuli (cyclical loading), which may favor developing slow and subcritical growth of cracks in ceramic materials and the degradation of the bond interface. Therefore, it is essential that the concepts which explain the fatigue mechanism are understood, as well as the crack propagation and failure patterns of restorative ceramic materials.
Assuntos
Cerâmica , Vidro , Teste de Materiais , Cerâmica/química , Cimentos Dentários , Odontologia , Porcelana Dentária , Propriedades de Superfície , Desenho Assistido por Computador , Análise do Estresse Dentário , Falha de Restauração DentáriaRESUMO
This study evaluated the effect of resin cement coating with high and low viscosities on the flexural fatigue strength of machined lithium disilicate glass-ceramic. Discs (IPS e.max CAD; Ivoclar Vivadent) were prepared and divided according to the surface condition (machining [M]-CEREC inLab; and polishing [P]-laboratory procedures), resin cement coating (with or without), and cement viscosity (high [H] and low [L]). The ceramic bonding surface was etched/primed by a one-step primer application followed by resin cement application (Variolink N base + high or low viscosity catalyst; Ivoclar Vivadent). Biaxial flexural fatigue strength was evaluated on a piston-on-three-ball set by the step-test method (n = 15) (initial stress: 60 MPa; incremental steps: 20 MPa; 10,000 cycles/step, at 20 Hz). Weibull statistics were used for fatigue data. Contact angle, topographic, and fractographic analysis were also performed. Machining produced statistically lower contact angle than polishing and a significant detrimental effect on the fatigue behavior (σ0 M = 247.2 [246.9-268.3]; σ0 P = 337.4 [297.8-382.4]). Machined groups followed by resin cement coating (σ0 MH = 297.9 [276.0-321.5]; σ0 Ml = 301.2 [277.1-327.4]) behaved similarly to the polished and coated groups (σ0 PH = 342.0 [308.9-378.5]; σ0 PL = 357.3 [324.7-393.1]), irrespective of the cement viscosity. Therefore, cement coating has able to revert the detrimental effects of the machining on the fatigue strength of lithium disilicate glass-ceramic. High and low viscosity cements behaved similarly in the improvement of CAD-CAM lithium disilicate fatigue strength.
Assuntos
Cerâmica , Cimentos de Resina , Propriedades de Superfície , Teste de Materiais , Porcelana DentáriaRESUMO
OBJECTIVES: To evaluate the fatigue failure load (FFL), cycles for fatigue failure (CFF) and survival rates of different occlusal thicknesses of resin composite simplified crowns with internal adjustments (IA) or without as control (C). METHODS: 30 monolithic simplified crowns of CAD/CAM resin composite (Tetric CAD, Ivoclar) were milled in three different occlusal thicknesses (0.5 mm, 1.0 mm, and 1.5 mm). Half of the crowns were submitted to restricted adjustment with diamond burs on the crown's inner surface and half remained milled without internal adjustment. The samples were treated and adhesively luted onto a prosthetic preparation made of epoxy resin reinforced by glass-fiber substrate. The sets were subjected to a fatigue test (cyclic fatigue: initial load of 200 N; step-size of 50 N; 10,000 cycles/step; 20 Hz; maximum load: 2800 N).Microscopic analysis of tested representative samples was performed. The fatigue data were statistically analyzed (α= 0.05) and the micrograpic images were qualitatively evaluated. RESULTS: All specimens from groups 1.0C and 1.5C survived the cyclic loads, while all 0.5C samples failed during the test. The 1.0IA and 1.5IA crowns showed no statistical difference for FFL (2530 N= 2670 N) and CFF (471,000 cycles= 499,000 cycles) between them, and they were both statistically superior to the 0.5IA (FFL= 1812.50 N; CFF= 327,500 cycles). The 1.0 mm and 1.5 mm crowns presented superior fatigue behavior (2530 N-2800 N) compared to the 0.5 mm crowns (1812 N-2140 N), whether internal adjustment was performed or not. A statistically significant difference was found for FFL and CFF of 0.5 mm crowns with and without internal adjustment, with a deleterious impact of the adjustment for both parameters (FFL and CFF: 0.5C > 0.5IA). SIGNIFICANCE: Resin composite milled crowns can bear high cyclic fatigue loads despite thickness, although thicker crowns had better mechanical behavior; however, the internal adjustment in the composite resin crown leads to a detrimental effect on its fatigue behavior, which presents a risk of mechanical failure due to premature fatigue.
Assuntos
Cerâmica , Resinas Compostas , Desenho Assistido por Computador , Porcelana Dentária , Falha de Restauração Dentária , Análise do Estresse Dentário , Teste de Materiais , Propriedades de Superfície , Suporte de CargaRESUMO
OBJECTIVES: To evaluate the effect of in-lab simulation of CAD/CAM grinding and intaglio surface treatments on the surface characteristics (topography and roughness) and fatigue behavior of adhesively luted 4YSZ simplified restorations. METHODS: Ceramic discs (Ø = 10 mm, thickness = 1 mm) were randomly allocated into 6 groups considering: "In-lab simulation of CAD/CAM grinding" (ground or polished) and "intaglio surface treatments": Ctrl (without surface treatment), AlOx (aluminum oxide air abrasion) or GLZ (glaze spray application). The surface roughness of all samples was measured, the treated discs received a ceramic primer, were luted with resin cement onto a dentin analogue material (woven glass-reinforced epoxy resin) and tested under a cyclic fatigue test (step-stress approach, n = 15; 1.4 Hz, 10,000 cycles/step, step-size of 100N starting at 200N until failure). A complementary analysis was performed to corroborate the findings in the fatigue test that the glaze fill defects increase the mechanical properties of the ceramic. To do so, bars (n= 10; 1.0 × 1.0 × 12 mm; considering the groups: N-ID: non-indented; ID: indented; ID-GLZ: indented plus glaze spray application) were indented in a vickers hardness tester to produce a crack pattern, treated with glaze or not, and then submitted to flexural strength tests (FS). Fractographic and topographic analysis were performed. RESULTS: In-lab simulation of CAD/CAM grinding decreased the fatigue failure load of the 4YSZ ceramic when comparing polished and ground groups, regardless of surface treatment. GLZ induced better fatigue performance compared to the air abrasion, regardless of the grinding condition (ground or polished surface). The results of the flexural strength test corroborated the findings in the fatigue test, as the ID-GLZ group presented superior FS than the ID group, however both had inferior FS than N-ID. There is an inverse association between roughness and fatigue failure load, as the higher the surface roughness, the lower the fatigue failure load. Failures in the fatigue and flexural strength tests started from the face subjected to tensile stresses. CONCLUSION: In-lab simulation of CAD/CAM grinding had a detrimental effect on the fatigue behavior of 4YSZ and glaze spray induced better 4YSZ performance compared to the air abrasion. The intaglio surface treatments differently influenced the 4YSZ fatigue performance, however, only glaze spray can reverse the damage caused by the grinding.
Assuntos
Cerâmica , Desenho Assistido por Computador , Porcelana Dentária , Análise do Estresse Dentário , Teste de Materiais , Propriedades de Superfície , Suporte de Carga , ZircônioRESUMO
This study compared the flexural strength under monotonic (static - sσ) and cyclic load application (fatigue - fσ), hardness (H) and fracture toughness (KIC) of different layers of a multi-layered zirconia (IPS e.max ZirCAD MT Multi, Ivoclar). Each layer was sectioned, classified into three groups according to yttria content (4-YSZ, 4/5-YSZ and 5-YSZ), and shaped on samples for flexural strength and fracture toughness tests (bars: 1.0 × 1.0 × 11 mm); and Vickers hardness test (plates: 1.5 × 4.0 × 5.0 mm). Flexural strength under monotonic load application (sσ; n = 10) was obtained through two different devices (three-point-bending and ball-in-hole device) and fatigue flexural strength (fσ; n = 15; initial load: 10 N; step-size: 5 N; 10,000 cycles/step) was assessed using a ball-in-hole device under cyclic load application. Vickers hardness test (n = 5), fracture toughness test (n = 10), and additional analyzes (Finite Element Analysis - FEA, Energy-dispersive X-ray spectroscopy - EDS and Scanning Electron Microscopy - SEM) were also performed. No differences were found between the different devices in the monotonic flexural strength test, and FEA showed similar tensile stress distribution for the two devices. 4-YSZ showed higher values of flexural strength under monotonic and cyclic load application modes (sσ = 1114.73 MPa; fσ = 798.84 MPa), and fracture toughness (KIC = 3.90 MPaâm). 4/5-YSZ had an intermediate sσ; however, fσ was similar to 5-YSZ (404.00-429.36 MPa) and KIC similar to 4-YSZ (KIC = 3.66 MPaâm). No statistical differences were found for hardness and Weibull modulus for fatigue flexural strength data. The amount of yttria in the layer compositions increased from 4-YSZ to 5-YSZ, and larger zirconia crystals were observed in the topographic images of 5-YSZ. Failures in the flexural strength and toughness tests started from the face subjected to tensile stress. Different layers of the multi-layered zirconia blank presented distinct mechanical properties. 4-YSZ (cervical layer) presented the highest flexural strength under monotonic and cyclic loads (fatigue), and higher fracture toughness even similar to the transition layer (4/5-YSZ). Hardness was similar between the layers. The ball-in-hole device performed similarly to the three-point bending device and can be used as an alternative to the traditional method.
Assuntos
Resistência à Flexão , Zircônio , Cerâmica/química , Porcelana Dentária , Dureza , Humanos , Teste de Materiais , Propriedades de Superfície , Ítrio , Zircônio/químicaRESUMO
This study evaluated the influence of ceramic surface conditioning and storage regimen (baseline vs. aging) on the fatigue performance of simplified lithium disilicate glass-ceramic restorations. A total of 90 ceramic discs (Ø= 10 mm; thickness= 1.0 mm) were allocated into 6 groups (n= 15), considering 2 factors: "ceramic surface treatment" - CA (only silane-based coupling agent, Monobond N), HF (5% hydrofluoric acid etching), or HF+CA (5% HF acid etching plus silane-based coupling agent); and "storage regimen" - baseline (24 hours - 5 days of distilled water at 37 °C), or long-term aging (180 days of distilled water at 37 °C + 25,000 thermal cycles). After intaglio ceramic conditioning, adhesive bonding (Multilink N) was performed onto epoxy resin discs (Ø= 10 mm; thickness= 2.5 mm) and the bonded sets were subjected to step-stress fatigue tests (initial load: 200 N; step-size: 50 N; 10,000 cycles per step; 20 Hz). Fatigue data were analyzed using Kaplan-Meier and Weibull statistical analyses. Fractography and topography analyses were also conducted. The fatigue findings demonstrated that the performance among groups for both baseline and aging conditions maintained a tendency: the CA groups had the worst behavior (baseline: 893 N/143,667 cycles; aging: 639 N/84,179 cycles), while the surface etching with HF (baseline: 1247 N/214,333 cycles; aging: 816.67 N/128,333 cycles) and HF+CA groups (baseline: 1290 N/222,333 cycles; aging: 900 N/145,000 cycles) had no statistically significant difference between them. The aging protocol reduced the performance of all groups. The groups with better fatigue performance (HF and HF+CA) did not have statistical differences regarding structural reliability (Weibull modulus). Most failures were radial cracks from the cementation interface, except for CA aging specimens, with 27% failing from debonding. The HF etching led to noteworthy surface topographical alterations. Micromechanical interlocking resulting from HF acid etching remained prevalent in the fatigue behavior. Thus, the silane-based coupling agent (Monobond N) does not need to be applied after HF etching in terms of fatigue behavior outcomes.
Assuntos
Colagem Dentária , Silanos , Cerâmica , Porcelana Dentária , Análise do Estresse Dentário , Ácido Fluorídrico , Teste de Materiais , Reprodutibilidade dos Testes , Cimentos de Resina , Propriedades de SuperfícieRESUMO
OBJECTIVE: To explore the effect of resin cement viscosities on the shear bond strength under static and fatigue load of lithium disilicate and dentin substrates. METHODS: Bonded tri-layer samples (lithium disilicate ceramic cylinder, resin cement, and substrate - ceramic or dentin) was performed considering 2 factors (n = 15): "resin cement viscosity" (high, HV; or low, LV) and "loading mode" (static, s-SBS; or fatigue shear bond strength, f-SBS). The specimens were subjected to s-SBS (1 mm/min, 1 kN load cell) and f-SBS (cyclic fatigue, initial load: 10 N; step-size: 5 N; 10,000 cycles/step; underwater). Failure mode, topography, and finite element analysis (FEA) were performed. RESULTS: The resin cement viscosity did not influence the s-SBS and f-SBS of lithium disilicate substrate; however, it affected the bond strength to dentin, with HV presenting the worst fatigue behavior (f-SBS = 6.89 MPa). Cyclic loading in shear testing induced a notorious detrimental effect with a relevant decrease (16-56 %) in bond strength and survival rates, except for dentin substrate and LV. Most failures were adhesive. A distinct pattern comparing the disilicate and dentin was identified and FEA demonstrated that there was a stress concentration on the top of the cement layer. SIGNIFICANCE: Cyclic fatigue loading in shear testing has detrimental effects on the adhesive behavior and survival probabilities of bonded lithium disilicate sets, regardless of resin cement viscosity. In contrast, resin cement viscosity affects the bond strength and the survival rates of dentin substrate submitted to cyclic loading mode, in which a low viscosity results in better performance.
Assuntos
Colagem Dentária , Cimentos de Resina , Cimentos de Resina/química , Viscosidade , Colagem Dentária/métodos , Análise do Estresse Dentário , Cimentos Dentários , Teste de Materiais , Porcelana Dentária/química , Cerâmica/química , Resistência ao Cisalhamento , Dentina , Propriedades de SuperfícieRESUMO
The aim of this study was to characterize the flexural strength and elastic modulus of CAD/CAM resin composite material and to evaluate the influence of different surface treatments and storage conditions on the fatigue behavior of bonded composite crowns. Bars (flexural strength, n= 30; elastic modulus, n= 5) (1.2 × 4 × 12 mm) were produced for three-point bending test and CAD/CAM milled crowns (n= 5) (thickness= 1 mm) adhesively cemented to an epoxy resin substrate for fatigue tests. Bars and crowns were randomly allocated into two "surface treatments": no surface treatment (CTRL) and air-abrasion with 110 µm Al2O3 particles (AlOx); while the crowns were also subdivided into "aging condition" (baseline - storage for 24 h to 7 days, and aging - storage for 150 days + 25,000 thermal cycles). The three-point bending test was performed according to ISO 6872 and the luted crowns were subjected to step-stress fatigue test (initial load of 200 N; step-size of 50 N; 10,000 cycles per step; 20 Hz). Complementary analysis by Stereomicroscopy and Field Emission Scanning Electron Microscopy (FE-SEM) were performed. The flexural strength and fatigue data were submitted to statistical tests (α= 0.05). The results showed that air-abrasion reduces the flexural strength and the characteristic strength of the resin composite, without modifying its elastic modulus or its structural reliability (Weibull Modulus). Air-abrasion did not influence the fatigue behavior of the cemented crowns. Notwithstanding, a decrease in the survival rate was observed after 445,000 cycles (2,400 N) when subjected to aging at both the CTRL or AlOx conditions. FE-SEM micrographs of the crowns showed that alumina particle air-abrasion treatment can modify the topography of its treated inner surface. Therefore, air-abrasion with alumina powder introduces defects onto the surface of the CAD/CAM resin composite material, decreasing the flexural strength, but without changing its elastic modulus and reliability. Adhesive cementation onto an epoxy resin substrate prevented an influence of the introduced defects on the fatigue performance of the resin composite restoration. Nevertheless, the fatigue behavior may be damaged by aging regimen.
Assuntos
Óxido de Alumínio , Resistência à Flexão , Cerâmica , Resinas Compostas , Desenho Assistido por Computador , Análise do Estresse Dentário , Teste de Materiais , Reprodutibilidade dos Testes , Cimentos de Resina , Propriedades de SuperfícieRESUMO
This study evaluated the effect of grinding and polishing the inner surface of monolithic discs made of zirconia polycrystals (ZR) and lithium disilicate glass-ceramic (LD) on the load-bearing capacity under fatigue of the restorations bonded onto a dentin analogue material (epoxy resin). ZR and LD ceramic discs (10 mm in diameter, 1 mm in thickness) were produced and randomly allocated into 10 groups considering the internal adjustment approach: Ctrl - No adjustment; F - Grinding with fine diamond bur (46 µm); F + Pol - Grinding with fine diamond bur followed by polishing with 2 tips (finisher and polisher); FF - Grinding with extrafine diamond bur (30 µm); FF + Pol - Grinding with extrafine diamond bur followed by polishing. In addition, discs (10 mm in diameter, 2.5 mm in thickness) of fiber reinforced epoxy resin were produced. Afterwards, the intaglio surface of the ZR discs were air-abraded with 45 µm alumina particles for 10 s, the LD and resin epoxy discs were etched with hydrofluoric acid (5%/20 s and 10%/60 s, respectively), and the treated discs were primed as recommended. Each ceramic disc was luted onto the epoxy resin disc with resin cement. Then, the samples were tested under a step-stress fatigue test (20 Hz, 10,000 cycles/step, step-size of 100 N starting at 200 N, and proceeding until failure detection). Fractographic, topographic and surface roughness analysis were also performed. The adjustments (grinding with or without polishing) (ZR: 733-880 N; LD: 1040-1106 N) triggered a detrimental effect on the fatigue behavior in both ceramics compared with the absence of treatment (control group; ZR: 973 N; LD: 1406 N). The polishing step had no effect on fatigue findings. Thus, grinding the inner surface of the tested ceramics should be avoided wherever possible to prevent introducing damage and its detrimental effects on the fatigue behavior.