Incorporation of zinc into cetylpyridinium chloride mouthwash affects the composition of multispecies biofilms.

This study evaluated the effect of a mouthwash containing 0.075% cetylpyridinium chloride and 0.28% zinc lactate (CPC + Zn) in a multispecies biofilm model. A 7-days 33-species biofilm, formed on Calgary device, was 1-min treated with: 0.12% chlorhexidine (CHX), culture medium (negative control), 0.075% cetylpyridinium chloride (CPC) or CPC + Zn, 2x/day, from day 3 until day 6. The metabolic activity and the microbial composition were evaluated by colorimetric method and checkerboard DNA-DNA hybridization, respectively. The three antimicrobials (CPC, CPC + Zn and CHX) reduced metabolic activity, total biofilm count and several species counts, including Porphyromonas gingivalis, Fusobacterium nucleatum, Parvimonas micra, Campylobacter gracilis and Streptococcus mutans. However, only CPC + Zn reduced counts of the pathogen Prevotella intermedia and did not interfere with the levels of some beneficial species in relation to the negative control. The treatment of multispecies subgingival biofilm with CPC + Zn was effective in controlling periodontal pathogens and favored the colonization of health-associated bacterial species.

Adverse events of metronidazole and amoxicillin: Retrospective analysis of a large data set of five randomized clinical trials.

AIM: To evaluate the frequency of side effects associated with intake of metronidazole (MTZ) + amoxicillin (AMX) in periodontal treatment, and to explore associations between these events and patients' features. MATERIALS AND METHODS: Data of five randomized clinical trials testing MTZ + AMX adjunctive to mechanical therapy were evaluated. Volunteers answered an adverse event questionnaire. RESULTS: Information from 656 subjects was assessed. The frequency of side effects in the antibiotic- and placebo-treated groups ranged from 1.0% to 17.7% and 0.9% to 13.7%, respectively. The events more frequently observed in the antibiotic than in the placebo group were diarrhoea and metallic taste (p < .05). Diabetes significantly raised the odds of a patient reporting discomfort (odds ratio [OR] = 2.6), diarrhoea (OR = 4.0), weakness (OR = 6.0) and excessive sleepiness (OR = 2.9). In systemically healthy volunteers, using antibiotics 3 months post-mechanical treatment (healing phase) (OR = 3.0), being a woman (OR = 3.9) and aged ≤49 (OR = 4.5) significantly increased the chances of reporting adverse events. CONCLUSIONS: The occurrence of side effects during MTZ + AMX treatment ranged from uncommon (1%) to very common (17.7%). The main factors raising the chances of a patient reporting adverse events were diabetes and taking antibiotics in the healing phase, instead of in the active phase of treatment. Patients ≤ 49 years old and females also tend to report more side effects.

In vitro evaluation of enamel surface roughness and morphology after orthodontic debonding: Traditional cleanup systems versus polymer bur.

INTRODUCTION: The primary aim of this randomized in vitro study was to compare the effectiveness of carbide, fibreglass and polymer burs on resinous remnant removal after bracket debonding, by the evaluation of enamel surface roughness and morphology. The secondary objective was to compare the time dispended on the procedures. METHODS: The buccal surfaces of 28 bovine incisors were analysed by a profilometer to initial roughness measurement (Ra-T1). Brackets were bonded with a light-cured resin and debonded with a debonding plier. The samples were randomly divided into four groups, according to the bur used (n=7): A-Tungsten carbide; B-Fibreglass; C-Polymer; D-Polymer with 75% ethanol pre-treatment. The second roughness measurements were made after resin removal (Ra-T2). Time for removal procedures was also recorded. The third measurements were made after polishing (Ra-T3). Scanning Electronic Microscopy was performed in two samples of each group: after resin removal and after polishing. Results of roughness and time measurements were statically analysed by analysis of variance with post-hoc Bonferroni. RESULTS: After polishing, tungsten carbide (P=0.1555) and fibreglass burs provided final surface roughness statistically similar to the baseline condition (P=1.0000). Yet, polymer burs, associated (P<0.0001) or not to alcohol (P<0.0001), provided surface roughness significantly higher when compared to baseline values. Polymer burs were more time-consuming on resinous remnant removal than tungsten carbide and fibreglass burs (P<0.05). CONCLUSION: Polymer burs were less effective and more time-consuming to remove the remaining resin than tungsten carbide and fibreglass burs. The polishing step created smoother surfaces regardless of the burs used for resin removal.

Análisis de flexión en alambres de níquel-titanio con y sin propiedades de transformación térmica / Bending analysis of nickel-titanium wires with and no thermal transformation properties

Objetivo: Evaluar el comportamiento de los alambres de aleación de níquel-titanio con y sin propiedades de transformación térmica en la relación carga/deflexión. Materiales y método: Para ello, 30 segmentos de alambres de níquel-titanio con calibre .014" y 30 mm de largo fueron cortados, conformando 10 segmentos de alambre Flexy NiTi de Orthometric®, 10 segmentos Flexy Copper NiTi termoactivado y 10 segmentos CuNiTi de OrmcoTM. Se usó una máquina universal de ensayos Instron® para analizar el comportamiento de carga y deflexión de los segmentos en una prueba de tres puntos, registrando las fuerzas alcanzadas en 0,5 mm: 1 mm, 2 mm y 4 mm de deflexión. Resultados: Hubo una diferencia estadísticamente significativa entre todos los alambres y entre todas las deflexiones, ya que el alambre Flexy Cooper NiTi presentó la menor carga entre todas las deflexiones analizadas. Conclusión: Se concluye que los alambres termoactivados alcanzan fuerzas más leves, lo que los hace más apropiados para alineaciones iniciales, las cuales requieren un mayor rango de deflexión(AU)