Survival rate and load to failure of premolars restored with inlays: An evaluation of different inlay fabrication methods.

STATEMENT OF PROBLEM: Studies that evaluate the survival rate and load to fracture of premolars restored with inlays produced using different methods are lacking. PURPOSE: The purpose of this in vitro study was to compare the survival rate and fracture load of premolars restored with inlays fabricated using different methods. MATERIAL AND METHODS: Thirty maxillary premolars were selected, embedded, and prepared to receive inlays fabricated using different methods (n=10): LaCom-digital scanning with Lava C.O.S. scanner (3M ESPE), followed by milling of composite resin block (Lava Ultimate; 3M ESPE) in a milling unit; CeCom-digital scanning with Cerec 3D Bluecam scanner (Dentsply Sirona), followed by milling of a Lava Ultimate block in Cerec (Dentsply Sirona); PresDis-impression with polyvinyl siloxane, inlay made using the lost wax technique, and IPS e.max Press (Ivoclar Vivadent AG) pressed ceramic (lithium disilicate). A dual-polymerizing resin cement system was used to lute the inlays. Inlays were mechanically cycled (2 Hz, 106 mechanical pulses, 80 N) after 24 hours, and the specimens were stored in distilled water at 37°C for 11 months. Then, a fatigue test was conducted using a 10-Hz frequency and 400-N load on the inner inclines of the cusps. The test was complete when the specimen fractured or when the specimen reached 1.5×106 cycles. The specimens that survived fatigue testing were submitted to a single-load fracture test in a universal testing machine and analyzed using a stereoscope for failure classification. Survival rates were estimated using the Kaplan-Meier method and log-rank test (Mantel-Cox). Fracture load data were analyzed using 1-way ANOVA (α=.05). RESULTS: No significant differences were detected among the groups for the survival rate (P=.87) or for the load to fracture (P=.78). Most failures were longitudinal, catastrophic fractures. CONCLUSIONS: Premolars restored with inlays fabricated using the tested methods had similar survival rates and loads to fracture.

A fully digital approach to replicate peri-implant soft tissue contours and emergence profile in the esthetic zone.

OBJECTIVE: This short communication reports on a novel digital technique designated - the "Fully Digital Technique (FDT)" - to take the impression of the peri-implant soft tissue and emergence profile with an intraoral scanner, digitally capturing both the three dimensional position of the implant platform and the coronal and gingival parts of the provisional retained restoration. MATERIALS AND METHODS: A first intraoral digital impression, which generated a standard triangulation language file (STL1), was taken using a standardized implant scanbody to detect the position of the implant. A second digital impression (STL2) with the provisional retained restoration in situ was performed in two steps: the first part of the scan captured all details of the vestibular and palatal sides of the provisional retained restoration and the adjacent teeth. The provisional retained restoration was then unscrewed, and the subgingival part of the restoration was scanned directly out of the mouth to determine its subgingival shape. STL1 and STL2 were imported into imaging software and superimposed using the "best fit" algorithm to achieve a new merged file (STL3) with the 3D implant position, the peri-implant mucosa, and emergence profile. The merged file was used to design the CAD/CAM customized abutment and to realize a stereolithographic model by 3D printing. RESULTS: The STL superimposition of digital impressions of the implant position and the provisional retained restoration constitute a novel technique to obtain a single STL file with the implant position and its peri-implant mucosal architecture. CONCLUSIONS: FDT is a rapid digital approach for achieving all information of the peri-implant soft tissue and emergence profile directly from the provisional retained restoration.

Fracture Strength of Endodontically Treated Teeth Restored with Composite Overlays with and without Glass-fiber Reinforcement.

PURPOSE: To evaluate the fracture strength and the failure mode of endodontically treated teeth restored with composite resin overlays with and without glass-fiber reinforcement. MATERIALS AND METHODS: A total of 32 extracted molars were divided into four equal groups. In the NFR-NFRC (no foundation restoration, no fiber-reinforced composite) and NFR-FRC (no foundation restoration, fiber-reinforced composite) groups, only a 5-mm-thick composite resin layer sealed the pulp chamber floors, whereas in the FR-NFRC (foundation restoration, no fiber-reinforced composite) and FR-FRC (foundation restoration, fiber-reinforced composite) groups, a 3.0-mm foundation restoration was used. NFR-NFRC and FR-NFRC groups were restored with composite resin overlays, whereas NFR-FRC and FR-FRC groups were restored with fiber-reinforced composite resin overlays. All specimens were subjected to mechanical loading in a computer-controlled masticator and then the fracture resistance was evaluated. Differences in means were compared using two-way ANOVA and Tukey's test. The level of significance was set at ɑ = 0.05. RESULTS: All specimens successfully completed the fatigue test. The least fracture-resistant group was NFR-FRC, exceeded by FR-NFRC, NFR-NFRC, and FR-FRC, in that order, with FR-FRC being the most fracture-resistant group. Statistically significant differences were detected between the pairs NFR-NFRC/FR-FRC (p = 0.001), NFR-FRC/FR-FRC (p = 0.001), and FR-NFRC/FR-FRC (p = 0.001). Eight vertical root fractures occurred in group FR-NFRC, six in group NFR-NFRC, four in group NFR-FRC, and none occurred in group FR-FRC. CONCLUSIONS: Within the limitations of this in vitro study, the incorporation of glass fibers and the presence of a foundation restoration were found to increase the fracture resistance and can favorably influence the fracture mode.

Marginal Adaptation, Gap Width, and Fracture Strength of Teeth Restored With Different All-Ceramic Vs Metal Ceramic Crown Systems: An in Vitro Study.

This study evaluated marginal adaptation before and after thermomechanical (TCML) loading, gap width and fracture strength of all-ceramic single crowns, as compared to porcelain-fused-to-metal (PFM). Thirty extracted premolars were prepared with a round shoulder of 1.0 mm depth. Specimens were restored with zirconia-ceramic (Group 1), lithium disilicate (Group 2) and metal-ceramic single crowns (Group 3). The replica of each sample was observed with a scanning electron microscope (SEM) to evaluate the crown-cement (c-c) and tooth-cement interface (t-c). After TCML, perfect margins decreased to 91.3% (c-c) and 93.9% (t-c) in Group 1, 94.6% (c-c) and 96.0% (t-c) in Group 2 and 73.5% (c-c) and 53.1% (t-c) in Group 3. The mean fracture strengths were 654.8 ± 98.1 N for Group 1, 551.3 ± 127 N for Group 2 and 501.43 ± 110.1 N for Group 3. All-ceramic systems could substitute for metal-ceramic crowns, but chipping of veneering ceramics, especially in zirconia-based crowns, should be investigated.

Work flow for the prosthetic rehabilitation of atrophic patients with a minimal-intervention CAD/CAM approach.

The implant-supported fixed rehabilitation of patients with an atrophic edentulous crest remains a challenge if bone augmentation is not planned. A minimal intervention approach for bone regeneration is necessary to minimize the flap overextension needed to close the defect over the augmented bone. Prosthetically guided bone regeneration can determine the amount of bone augmentation necessary for definitive prosthetic fixed rehabilitation. The positions of the implants and prosthetic restoration were planned; a 0.3 mm thick titanium mesh was customized for bone augmentation by using computer-aided design and computer-aided manufacturing and rapid prototyped by laser sintering, and the definitive prosthetic rehabilitation was carried out according to the initial treatment plan. This resulted in minimal bone augmentation relative to the functional needs of the definitive prosthetic rehabilitation.

Efficacy of surface treatments on the bond strength of resin cements to two brands of zirconia ceramic.

PURPOSE: To compare the shear bond strengths (SBS) of two cements to two Y-TZP ceramics subjected to different surface treatments. MATERIALS AND METHODS: Zirconia specimens were made from Lava (n = 36) and IPS e.max ZirCAD (n = 36), and their surfaces were treated as follows: no treatment (control), silica coating with 30-µm silica-modified alumina (Al2O3) particles (CoJet Sand), or coating with liners Lava Ceram for Lava and Intensive ZirLiner for IPS e.max ZirCAD. Composite resin cylinders were bonded to zirconia with Panavia F or RelyX Unicem resin cements. All specimens were thermocycled (6000 cycles at 5°C/55°C) and subjected to SBS testing. Data were analyzed by three-way ANOVA and Tukey's (HSD) post-hoc test (α = 0.05). Failure mode was analyzed by stereomicroscope and SEM. RESULTS: CoJet Sand and liners promoted significantly higher SBS than their control groups, but had similar results to one another. Panavia F provided significantly higher SBS values than RelyX Unicem (p < 0.01) for nontreated zirconia specimens of both brands. When Lava and IPS e.max ZirCAD were abraded with CoJet Sand, RelyX Unicem promoted significantly higher SBS values than Panavia F (p < 0.001). There was no significant difference between the two cements when the zirconia specimens were treated with their respective liners. The nontreated specimens and those treated with CoJet Sand exhibited a high percentage of adhesive and mixed A failures, while the specimens treated with liners presented an increase in mixed A and mixed C failures as well as some cohesive failure in the bulk of Lava Ceram for both cements. CONCLUSION: CoJet Sand and liners provided the best surface treatment for Lava and IPS e.max ZirCAD. The best surface treatment/cement combinations were CoJet Sand/RelyX Unicem and liner/Panavia F. SBS of Panavia F and RelyX Unicem was not influenced by the zirconia brand.

Computer-aided design and manufacturing construction of a surgical template for craniofacial implant positioning to support a definitive nasal prosthesis.

AIM: To design a surgical template to guide the insertion of craniofacial implants for nasal prosthesis retention. MATERIALS AND METHODS: The planning of the implant position was obtained using software for virtual surgery; the positions were transferred to a free-form computer-aided design modeling software and used to design the surgical guides. A rapid prototyping system was used to 3D-print a three-part template: a helmet to support the others, a starting guide to mark the skin before flap elevation, and a surgical guide for bone drilling. An accuracy evaluation between the planned and the placed final position of each implant was carried out by measuring the inclination of the axis of the implant (angular deviation) and the position of the apex of the implant (deviation at apex). RESULTS: The implant in the glabella differed in angulation by 7.78°, while the two implants in the premaxilla differed by 1.86 and 4.55°, respectively. The deviation values at the apex of the implants with respect to the planned position were 1.17 mm for the implant in the glabella and 2.81 and 3.39 mm, respectively, for those implanted in the maxilla. CONCLUSIONS: The protocol presented in this article may represent a viable way to position craniofacial implants for supporting nasal prostheses.

Pilot evaluation of four experimental conditioning treatments to improve the bond strength between resin cement and Y-TZP ceramic.

PURPOSE: This study evaluated the bond strength between resin cement and Y-TZP ceramic (Yttrium-stabilized Tetragonal Zirconia Polycrystalline) submitted to different surface conditionings. MATERIALS AND METHODS: Fifty Y-TZP ceramic discs (Ø= 10 mm) were allocated into five groups: Gr1 (control)-no conditioning; Gr2-tribochemical silica coating (30-µm SiO(2)) before sintering; Gr3-air abrasion with 50-µm Al(2)O(3) before sintering; Gr4-air abrasion with 110-µ Al(2)O(3) before sintering; Gr5 - air abrasion with 50-µm Al(2)O(3) after sintering. After specimen preparation, cylinders of composite resin were prepared and immediately cemented onto the ceramic. A shear test was performed. RESULTS: One-way ANOVA indicated a statistically significant difference among the groups (p= 0.0019). The mean shear bond strengths (MPa) were: Gr1 = 4.7 ± 0.8,(b) Gr2 = 4.6 ± 0.9,(b) Gr3 = 6.4 ± 1.0,(a) Gr4 = 6.5 ± 1.8,(a) Gr5 = 6 ± 1.3(ab) (same superscript letter indicates statistical similarity). Adhesive fracture between the ceramic and resin cement was the most common failure. No complete cohesive fracture at the ceramic or composite cylinders was noted. CONCLUSION: Within the limitations of this study, additional surface treatment with air abrasion before and after sintering provided a significant increase in bond strength. Tribochemical silica coating before sintering was not effective as a surface treatment.

Immediate facial rehabilitation in cancer patients using CAD-CAM and rapid prototyping technology: a pilot study.

PURPOSE: This study describes the workflow in a procedure to create a provisional facial prosthesis for cancer patients using digital and rapid prototyping technologies without the need for supporting craniofacial implants. MATERIALS AND METHODS: An integrated workflow procedure aimed at the construction of provisional silicone prosthesis was used to rehabilitate a facial disfigurement in a patient who had undergone ablative surgery of the midface. A laser scan of the defect was obtained, and a digital model of the patient's face was constructed using virtual mirroring of the healthy side and referencing the "Nose Digital Library." RESULTS: The missing volume of the face was reconstructed, and a rapid-prototyped mold was devised to process the silicone prosthesis. A provisional eyeglasses-supported prosthesis designed with a CAD/CAM-projected titanium substructure was connected using the micro-components of implant prosthetic devices. CONCLUSIONS: The workflow described herein offers a viable procedure for quickly restoring facial defects by means of provisional prosthetic rehabilitation.

Rehabilitation of the nose using CAD/CAM and rapid prototyping technology after ablative surgery of squamous cell carcinoma: a pilot clinical report.

Restoration of a nasal defect after ablative surgery for squamous cell carcinoma necessitates replacing the missing volume and anchoring a prosthesis to the patient's face. This report describes the failure of plastic reconstructive surgery after ablation of a squamous cell cancer of the nose and the esthetic and functional restoration of the patient with a nasal prosthesis. The process of making an implant-supported prosthesis using digital technology, including digitized anatomic models from a "nose library," and the rapid prototyping of the mesiostructure for bar anchorage and of the mold for silicone processing are presented.

Translucency of zirconia copings made with different CAD/CAM systems.

STATEMENT OF PROBLEM: Zirconia cores are reported to be less translucent than glass, lithium disilicate, or alumina cores. This could affect the esthetic appearance and the clinical choices made when using zirconia-based restorations. PURPOSE: The purpose of this in vitro study was to evaluate the translucency of zirconia copings for single crowns fabricated using different CAD/CAM systems, using lithium disilicate glass ceramic as a control. MATERIAL AND METHODS: Using impressions made from a stainless steel complete-crown master die, 9 stone cast replicas were fabricated, numbered, and distributed into 8 ceramic ZrO(2) CAD/CAM system groups (Lava Frame 0.3 and 0.5, IPS e.max ZirCAD, VITA YZ, Procera AllZircon, Digizon, DC Zircon, and Cercon Base) and to a lithium disilicate glass-ceramic control group (IPS e.max Press) using a simple computer-generated randomization method. From each die, the manufacturer's authorized milling centers supplied 5 copings per group without applying any dying technique to the ceramic base material. The copings were prepared to allow for a 40-mum cement layer and were of different thicknesses according to system specifications. Translucency was measured by the direct transmission method with a digital photoradiometer mounted in a dark chamber. The light source was a 150-W halogen lamp beam. Measurements were repeated 3 times for each specimen. Data obtained were analyzed using 1-way ANOVA and the Bonferroni multiple comparison test (alpha=.05). RESULTS: Among ZrO(2) copings, Lava (0.3 mm and 0.5 mm thick) showed the highest (P<.05) values of translucency measured as light flow units (3.572 + or - 018 x 10(3) lx and 3.181 + or - 0.13 x 10(3) lx, respectively). These values represent 71.7% and 63.9%, respectively, of the glass-ceramic control group (4.98 x 10(3) lx). CONCLUSIONS: All ZrO(2) copings demonstrated different levels of light transmission, with the 2 Lava specimens showing the highest values. Translucency of zirconia copings was significantly lower (P=.001) than that of the lithium disilicate glass-ceramic control.

Surface roughness and bacterial adherence to resin composites and ceramics.

PURPOSE: The aim of this study was to evaluate the surface roughness and the in vitro adherence of Streptococcus mutans to indirect aesthetic restorative materials that are uncoated with saliva. MATERIALS AND METHODS: Four groups of restorative materials were evaluated according to material type: (1) microparticulate feldspathic ceramic; (2) leucite-reinforced feldspathic ceramic; (3) microhybrid resin composite and (4) microfilled resin composite. Twenty standardised samples of each material were produced. Roughness analysis (Ra, n = 10) was performed using a roughness analyser. Adhesion tests (n = 10) were carried out in 24-well plates; colony-forming units (CFU/mL) were evaluated. The mean values of roughness (microm) and adherence (CFU/mL) for each group were subjected to an analysis of variance and a Tukey test. RESULTS: The leucite-reinforced feldspathic ceramic was rougher and presented higher bacterial adherence than the microparticulate feldspathic ceramic. The resin composites were similar with regard to surface roughness and bacterial adherence. CONCLUSIONS: The microhybrid and microfilled resin composites were similar and the leucite-reinforced feldspathic ceramic was rougher and presented higher bacterial adherence than the microparticulate feldspathic ceramic.

Evaluation of the accuracy and stress distribution of 3-unit implant supported prostheses obtained by different manufacturing methods.

The purpose of this in vitro study was to measure the vertical, positive-horizontal, and negative-horizontal misfit (VM, PHM, and NHM, respectively) of the zirconia three-element prosthetic framework, fabricated using different methods, and compare them with conventional fabrication methods (lost-wax casting). Furthermore, this study aimed to evaluate the influence of the misfit values on the biomechanical behavior of the 3-unit fixed prosthetic frameworks using three-dimensional finite element analysis (3D-FEA). Forty frameworks (n = 10) were fabricated as follow: G1, Cerec Bluecam; G2, iTero; G3, 3Series; and G4, conventional method. The samples were randomized to measure marginal misfit using a high-precision three-dimensional (3D)-optical microscope. The results were submitted to analysis of variance (ANOVA), with the significance level set at 5%. The mean VM values of each group were used in creating the models by 3D-FEA with the misfit found in optical microscopy. The programs used were the InVesalius, Rhinoceros, SolidWorks, FEMAP and NEiNastran. The von Mises map was plotted for each model. The G4 showed the lowest mean VM value (16.73 µm), followed by G3 (20.71 µm), G2 (21.01 µm), and G1 (41.77 µm) (p < 0.001). G2 was more accurate than G1 (p < 0.05) and similar to G3 (p = 0.319). For PHM, G4 was the most accurate and did not present overextended values. With regard to NHM, the computer-aided design and computer-aided manufacturing (CAD-CAM) systems were more accurate (-61.91 µm) than G4 (-95.36 µm) (p = 0.014). In biomechanical analysis, stress concentration caused by oblique loading is greater than caused by axial loading. In axial loading, G4 was the most favorable while G1 was the least favorable, biomechanically, in oblique loading, similar stress patterns were observed in all the models. The prosthetic screw was the most overloaded structure, but the material did not influence the stress distribution. The misfit prostheses showed a greater degree of stress than the controls (without misfit). The manufacturing method influenced the marginal misfit of the frameworks, with the conventional method being the most accurate and the Cerec Bluecam System (closed system) the least accurate. Biomechanically, fitting prostheses were more favorable than misfit prostheses.

Replacement of mandibular molars with single-unit restorations supported by wide-body implants: immediate versus delayed loading. A randomized controlled study.

PURPOSE: This prospective randomized controlled trial aimed to compare single implant-supported mandibular molar restorations using either an immediate or a delayed loading protocol. MATERIALS AND METHODS: Thirty subjects requiring single mandibular molar replacement were consecutively treated. One implant was placed in each patient. Fifteen subjects were assigned to delayed loading protocol and 15 to immediate loading protocol according to a randomization table. After insertion, the delayed loaded implants were connected to a healing abutment and restored after 3 to 4 months of healing without loading. The immediately loaded implants were loaded within 24 hours of surgery with a provisional restoration. The interim prosthesis was placed in centric occlusion. All contacts in lateral excursions were eliminated. At implant placement the maximum value of insertion torque was recorded. Radiographic bone level change was measured on periapical radiographs obtained at the time of implant placement and 12 months after loading. Means of the 2 groups were compared by Student t test and analysis of variance (ANOVA). The level of significance was set at .05. RESULTS: No implants were lost in the delayed loading group (0/15), whereas 1 implant failed (1/15) in the immediate loading group. No differences were observed in relation to implant length or insertion torque between the groups. The average radiographic bone level change after 1 year of function was 1.2 +/- 0.55 mm (range, 0.5 to 2.6 mm) and 0.77 +/- 0.38 mm (range, 0.29 to 1.23 mm) for the delayed loaded and the immediately loaded implants, respectively. The difference in radiographic bone level change between the delayed and immediate loading groups was statistically significant (P = .022; CI = -0.79 to -0.06; Student t test). CONCLUSIONS: Immediate loading of wide-diameter implants supporting single restorations in mandibular molar sites seems to be a suitable clinical option. Moreover, the radiographic bone level change observed after 12 months of loading was significantly less for immediately loaded implants.

Bonding effectiveness and sealing ability of fiber-post bonding.

OBJECTIVES: To evaluate the push-out bond strength and the sealing ability of five adhesive cements routinely used for fiber-post bonding. METHODS: Fifty extracted single-rooted teeth were randomly divided in five groups and restored using Parapost FiberLux and the following luting agents: Panavia 21 (PAN), Clearfil Esthetic Cement (CLF), Variolink II (VAR), RelyX Unicem (UNI) and experimental GC self-adhesive cement (EGC). After 1 week of water storage at 37 degrees C, three sections (coronal, middle and apical) of 2mm thickness were prepared from each specimen. Sealing ability was quantified with a fluid-filtration system (Flodec) during 10 min, after which the push-out bond strength was immediately measured. Data were analyzed with ANOVA (push-out) and Kruskal-Wallis (sealing ability). RESULTS: The push-out bond strength and sealing ability were not significantly different among the coronal, middle and apical sections for each luting agent. The highest push-out bond strength was measured for CLF (14.60+/-3.63 MPa), which was not significantly different from PAN (12.57+/-2.45 MPa), but significantly higher than VAR (11.09+/-4.09 MPa), UNI (11.29+/-4.31 MPa) and EGC (7.65+/-4.79 MPa). When evaluating the sealing ability, significant differences were not found among PAN, CLF and VAR, and between UNI and EGC. The latter luting agents scored significantly lower than the former ones. The push-out bond strength was correlated to the sealing ability (p<0.001). SIGNIFICANCE: The self-etching MDP-based cements presented the highest push-out bond strength. Although the bonding effectiveness of self-adhesive cements appears promising, their interaction with root dentin might be too weak to minimize microleakage at the post-cement-dentin interface.

Evaluation of light transmission through translucent and opaque posts.

OBJECTIVES: The transmission of light through translucent posts was observed, and the microhardness of light-cured cement used to secure these posts was evaluated at different depths. METHODS: Fifteen single-rooted standard bovine teeth, 16 mm in size, were used. The root canals were prepared using #3 drills Light-Post (five teeth) and Aestheti Post (five teeth) systems (BISCO), with a working-length of 12 mm. In five teeth, translucent posts were cemented (Light-Post #2), while another five teeth received opaque posts (Aestheti Post #2). The roots were painted with black nail varnish to prevent the passage of light through the lateral walls of the roots. The root canals of all the specimens were treated with the All-Bond 2 adhesive system (BISCO) and cemented with light-cured cement (Enforce, Dentsply). All the roots were transversally cut to obtain six specimens 1.5 mm thick. Every two sections corresponded to a specific region of the root (cervical, middle, apical), making it possible to observe the cement microhardness at different levels. The groups (n = 10) were defined as: GI: translucent post (TP)/cervical region; G2: TP/middle region; G3: TP/apical region; G4: Opaque post (OP)/cervical region; G5: OP/middle region; G6: PO/apical region. Five root canals were only filled with cement for use as a control (G7). Then, Vickers microhardness analyses were performed. RESULTS: In G3, G5 and G6, the cement was not sufficiently hard to allow for microhardness analysis. When submitted to the ANOVA test, G1 (35.07), G2 (24.28) and G4 (28.64) presented no statistical differences. When the previous groups were compared to G7 (51.00) using the Kruskal-Wallis test, a statistical difference was found. CONCLUSION: Translucent posts allow cement polymerization up to the middle portion of the root.

Fatigue resistance of bovine teeth restored with resin-bonded fiber posts: effect of post surface conditioning.

This study evaluated the effect of post surface conditioning on the fatigue resistance of bovine teeth restored with resin-bonded fiber-reinforced composite (FRC). Root canals of 20 single-rooted bovine teeth (16 mm long) were prepared to 12 mm using a preparation drill of a double-tapered fiber post system. Using acrylic resin, each specimen was embedded (up to 3.0 mm from the cervical part of the specimen) in a PVC cylinder and allocated into one of two groups (n = 10) based on the post surface conditioning method: acid etching plus silanization or tribochemical silica coating (30 pm SiO(x) + silanization). The root canal dentin was etched (H2PO3 for 30 seconds), rinsed, and dried. A multi-step adhesive system was applied to the root dentin and the fiber posts were cemented with resin cement. The specimens were submitted to one million fatigue cycles. After fatigue testing, a score was given based on the number of fatigue cycles until fracture. All of the specimens were resistant to fatigue. No fracture of the root or the post and no loss of retention of the post were observed. The methodology and the results of this study indicate that tribochemical silica coating and acid etching performed equally well when dynamic mechanical loading was used.

Adherence of Streptococcus mutans to uncoated and saliva-coated glass-ceramics and composites.

This study sought to investigate the surface roughness and the S ence of Streptococcus mutans (in the presence and absence of saliva) to ceramics and composites. The early dental biofilms formed in situ on the materials were illustrated, using scanning electron ascopy (SEM). Feldspathic and leucite/feldspathic ceramics and microhybrid and microfilled composites were evaluated. Human dental enamel was used as the control. Standardized specimens of the miaterials were produced and surface roughness was analyzed. The dhesion tests were carried out in 24-well plates and colony forming units (CFU/mL) were evaluated. Values of roughness (microm) ,adherence (CFU/mL) were analyzed statistically. Of all the surfaces tested, enamel was the roughest. Leucite/feldspathic ceramics were rougher than the feldspathic ceramic, while composites were similar statistically. Enamel offered the highest level of adherence to uncoated and saliva-coated specimens, while the leucite/feldspathic ceramic demonstrated greater adherence than the feldspathic ceramic and the composites were similar statically. The rougher restorative materials increased the adherence of S. mutans on the material surfaces.

Prosthetically CAD-CAM-Guided Bone Augmentation of Atrophic Jaws Using Customized Titanium Mesh: Preliminary Results of an Open Prospective Study.

This study evaluated the outcomes of computer-aided design-computer-aided machining (CAD-CAM)-customized titanium mesh used for prosthetically guided bone augmentation related to the occlusion-driven implant position, to the vertical bone volume gain of the mandible and maxilla, and to complications, such as mesh exposure. Nine patients scheduled for bone augmentation of atrophic sites were treated with custom titanium mesh and particulate bone grafts with autologous bone and anorganic bovine bone in a 1:1 ratio prior to implant surgery. The bone volume needed to augment was virtually projected based on implant position, width, and length, and the mesh design was programmed for the necessary retaining screws. After 6 to 8 months, bone augmentations of 1.72 to 4.1 mm (mean: 3.83 mm) for the mandibular arch and 2.14 to 6.88 mm (mean: 3.95 mm) for the maxilla were registered on cone-beam computerized tomography. Mesh premature (within 4 to 6 weeks) exposure was observed in 3 cases and delayed (after 4 to 6 weeks) in 3 other cases. One titanium mesh was removed before the programmed time but in all augmented sites was possible implant insertion. No complication occurred during prosthetic follow-up. Using CAD-CAM technology for prosthetically guided bone augmentation showed important postoperative morbidity of mesh exposure (66%). Because of this high prevalence of mesh exposure and the potential infection that could affect the expected bone augmentation, this study suggests a cautious approach to this procedure when designing the titanium mesh, to avoid flap tension that may cause mucosal rupture.

Immediate loading of two implants supporting a ball attachment-retained mandibular overdenture: a prospective clinical study.

BACKGROUND: A prospective clinical study was conducted to evaluate clinically and radiographically the performance of two implants immediately loaded supporting a ball attachment-retained mandibular overdenture. MATERIALS AND METHODS: Seventeen completely edentulous patients were included in the study. Each patient received two implants inserted after a minimal flap reflection and no vestibular extension in order to reduce the postoperative swelling and facilitate immediate prosthesis connection. After implant placement, a mandibular complete denture was connected to the implants using ball attachments of appropriate height according to the depth of the peri-implant tissue. Patients were asked not to remove the denture for 1 week. No limitations to chewing function were given. At implant placement, the maximum value of insertion torque was recorded. Patients were examined at 1, 2, 4, 12, and 52 weeks postsurgery. At postoperative visit, occlusion was checked and the need for any prosthesis maintenance was recorded. The radiographic bone level (RBL) change was measured on periapical radiographs at baseline and 12 months after loading. RESULTS: After 12 months of loading, no implant failure was reported and the survival rate was 100%. Average RBL change was 0.7 mm +/- 0.5 mm. Of the 17 cases, two had major prosthetic complications and five patients required minor extra maintenance appointments. CONCLUSIONS: The immediate loading of two implants by means of ball attachment-retained mandibular complete denture may be a predictable treatment option. This clinical approach offers increased stability and comfort, while keeping a high implant success rate.