Relationships between Flexural and Bonding Properties, Marginal Adaptation, and Polymerization Shrinkage in Flowable Composite Restorations for Dental Application.

To evaluate the flexural and bonding properties, marginal adaptation, and polymerization shrinkage in flowable composite restorations and their relationships, four new generation flowable composites, one conventional, and one bulk-fill flowable composite were used in this study. Flexural properties of the composites and shear bond strength to enamel and dentin for flowable restorations were measured immediately and 24 h after polymerization. Marginal adaptation, polymerization shrinkage, and stress were also investigated immediately after polymerization. The flexural properties, and bond strength of the flowable composites to enamel and dentin were much lower immediately after polymerization than at 24 h, regardless of the type of the composite. Polymerization shrinkage and stress varied depending on the material, and bulk-fill flowable composite showed much lower values than the others. The marginal adaptation and polymerization shrinkage of the composites appeared to have a much stronger correlation with a shear bond strength to dentin than to enamel. The weak mechanical properties and bond strengths of flowable composites in the early stage after polymerization must be taken into account when using them in the clinic. In addition, clinicians should be aware that polymerization shrinkage of flowable composites can still lead to the formation of gaps and failure of adaptation to the cavity regardless of the type of composite.

Effect of intracoronal bleaching agents on dentin microhardness.

The purpose of this in vitro study was to compare the effect of intracoronal bleaching agents associated or unassociated with chlorhexidine gel on dentin microhardness. Sixty human maxillary incisor crowns were divided into six groups, and bleaching agents were sealed into the pulp chambers as follows: sodium perborate + water (SPW), sodium perborate + 2% chlorhexidine gel (SP + CHX), sodium perborate + 30% hydrogen peroxide solution (SP + HP), 37% carbamide peroxide gel (CP), 37% carbamide peroxide gel + 2% chlorhexidine gel (CP+CHX), and water (W). After the bleaching procedure, microhardness testing was carried out on the dentin surface at three different levels: inner, middle, and outer dentin. The greatest reduction in microhardness was observed for the SP + HP group. No differences were observed between the SPW and SP + CHX group. The 2% chlorhexidine gel did not adversely affect dentin microhardness when associated with the tested bleaching agents. CHX might be considered as an antimicrobial vehicle during intracoronal bleaching.

Effect of nonvital tooth bleaching on resin/enamel shear bond strength.

PURPOSE: This study evaluated the effect of nonvital tooth bleaching on shear bond strength (SBS) of the composite resin/bovine enamel interface at different periods of time after bleaching. MATERIALS AND METHODS: Three hundred twenty teeth were randomly divided into four groups according to bleaching agent: SPH: sodium perborate and 30% hydrogen peroxide; SPW: sodium perborate and distilled water; CP: 37% carbamide peroxide; and PLA: distilled water (placebo). The bleaching agents in the pulp chambers were replaced every 7 days for 4 weeks. For SBS testing, each of these groups was randomly divided into four subgroups (n = 20) according to the postbleaching periods of time: 0 (baseline), 7, 14, and 21 days. At the respective time, enamel slabs were embedded in polyester resin and flattened. Composite resin cylinders (Z100/Single bond, 3M) were bonded to the enamel surface and subjected to the SBS test using a universal testing machine. RESULTS: The ANOVA and Tukey's test (alpha = 0.05) showed statistically significant differences (expressed by different letters) among the bleaching agents only at follows: PLA (a), CP (ab), SPW (ab), and SPH (b). The SPH group, showing the lowest mean value, differed significantly from the control group. At 7, 14, and 21 days, no significant differences were observed. CONCLUSION: Nonvital tooth bleaching affected the resin/enamel SBS values when sodium perborate mixed with 30% hydrogen peroxide was used.

Use of 37% carbamide peroxide in the walking bleach technique: a case report.

Dental bleaching represents an effective, conservative, and relatively low-cost method for improving the appearance of discolored pulpless teeth. Among the bleaching techniques, the walking bleach technique with sodium perborate associated with water or hydrogen peroxide stands out because of its esthetic results and safety. A modified walking bleach technique with the use of 37% carbamide peroxide as the bleaching agent is presented. Additionally, the adverse effects of dental bleaching in the following restorative procedures are discussed, showing the advantages with the use of 37% carbamide peroxide.

Bond strength of different endodontic sealers to dentin: push-out test.

OBJECTIVE: The aim of this in vitro study was to evaluate the bond strength of different root canal sealers to dentin. MATERIAL AND METHODS: Forty extracted single-rooted human teeth were examined and the coronal and middle thirds of the canals were prepared with a 1.50 mm post drill (FibreKor Post System, Pentron). The teeth were allocated in two experimental groups, irrigated with 2.5% NaOCl+17% EDTA or saline solution (control group) and instrumented using Race rotary files (FKG) to a size #40 at the working length. Then, the groups were divided into four subgroups and filled with Epiphany sealer (Group 1), EndoREZ (Group 2), AH26 (Group 3) and Grossman's Sealer (Group 4). After 2 weeks of storage in 100% humidity at 37ºC, all teeth were sectioned transversally into 2-mm-thick discs. Push-out tests were performed at a cross-head speed of 1 mm/min using a universal testing machine. The maximum load at failure was recorded and expressed in MPa. RESULTS: Means (±SD) in root canals irrigated with 2.5% NaOCl and 17% EDTA were: G1 (21.6±6.0), G2 (15.2±3.7), G3 (14.6±4.5) and G4 (11.7±4.1).Two-way ANOVA and Tukey's test showed the highest bond strength for the Epiphany's group (p< 0.01) when compared to the other tested sealers. Saline solution decreased the values of bond-strength (p<0.05) for all sealers. CONCLUSION: Epiphany sealer presented higher bond strength values to dentin in both irrigating protocols, and the use of 2.5% NaOCl and 17% EDTA increased the bond strength values for all sealers.

Bond strength of different endodontic sealers to dentin: push-out test

OBJECTIVE: The aim of this in vitro study was to evaluate the bond strength of different root canal sealers to dentin. MATERIAL AND METHODS: Forty extracted single-rooted human teeth were examined and the coronal and middle thirds of the canals were prepared with a 1.50 mm post drill (FibreKor Post System, Pentron). The teeth were allocated in two experimental groups, irrigated with 2.5 percent NaOCl+17 percent EDTA or saline solution (control group) and instrumented using Race rotary files (FKG) to a size #40 at the working length. Then, the groups were divided into four subgroups and filled with Epiphany sealer (Group 1), EndoREZ (Group 2), AH26 (Group 3) and Grossman's Sealer (Group 4). After 2 weeks of storage in 100 percent humidity at 37ºC, all teeth were sectioned transversally into 2-mm-thick discs. Push-out tests were performed at a cross-head speed of 1 mm/min using a universal testing machine. The maximum load at failure was recorded and expressed in MPa. RESULTS: Means (±SD) in root canals irrigated with 2.5 percent NaOCl and 17 percent EDTA were: G1 (21.6±6.0), G2 (15.2±3.7), G3 (14.6±4.5) and G4 (11.7±4.1).Two-way ANOVA and Tukey's test showed the highest bond strength for the Epiphany's group (p< 0.01) when compared to the other tested sealers. Saline solution decreased the values of bond-strength (p<0.05) for all sealers. CONCLUSION: Epiphany sealer presented higher bond strength values to dentin in both irrigating protocols, and the use of 2.5 percent NaOCl and 17 percent EDTA increased the bond strength values for all sealers.

Influence of post-bleaching time intervals on dentin bond strength.

It has been reported that bond strength of resin to tooth structure can be reduced when the bonding procedure is carried out immediately after the bleaching treatment. This study evaluated the effect of bleaching of non-vital teeth bleaching on the shear bond strength (SBS) of composite resin/bovine dentin interface and the influence of delaying the bonding procedures for different time intervals following internal bleaching. According to a randomized block design, composite resin cylinders (Z100/Single bond - 3M) were bonded to the flattened dentin surface of two hundred and fifty-six teeth which had previously been subjected to four different treatments: SPH - sodium perborate + 30% hydrogen peroxide; SPW - sodium perborate + distilled water; CP - 37% carbamide peroxide; and CON - distilled water (control), each one followed by storage in artificial saliva for 0 (baseline), 7, 14, and 21 days after bleaching (n = 16). The bleaching agents in the pulp chambers were replaced every 7 days, over 4 weeks. The SBS test of the blocks was done using a universal testing machine. The ANOVA showed that there was no significant interaction between time and bleaching agents, and that the factor time was not statistically significant (p > 0.05). For the factor bleaching treatment, the Student's t-test showed that [CON = CP] > [SPW = SPH]. The bleaching of non-vital teeth affected the resin/dentin SBS values when sodium perborate mixed with 30% hydrogen peroxide or water was used, independently of the elapsed time following the bleaching treatment.

Influence of post-bleaching time intervals on dentin bond strength

Tem-se sugerido que a qualidade da adesão resina composta-dentina pode ser prejudicada quando restaurações são confeccionadas imediatamente após o tratamento clareador. Este estudo avaliou o efeito da postergação do procedimento adesivo após o clareamento interno realizado com diferentes agentes na resistência ao cisalhamento da interface compósito/dentina. De acordo com um delineamento aleatório em blocos completos, cilindros de resina composta (Z100/Single Bond - 3M) foram confeccionados em duzentos e cinqüenta e seis fragmentos dentinários bovinos planificados, os quais foram previamente submetidos a 4 tratamentos: PSH - perborato de sódio + peróxido de hidrogênio a 30%; PSA - perborato de sódio + água destilada; PC - peróxido de carbamida a 37% e CON - água destilada (controle), sendo estes seguidos pelo armazenamento em saliva artificial por 0, 7, 14 e 21 dias após o clareamento (n = 16). Os agentes clareadores inseridos na câmara pulpar foram substituídos a cada 7 dias, durante 4 semanas. O teste de resistência ao cisalhamento foi realizado em máquina de ensaios universal. ANOVA mostrou que a interação entre os tempos e os agentes clareadores não foi significativa (p > 0,05). Para o fator tratamento clareador, o teste t de Student revelou que [PC = CON] > [PSA = PSH]. Independentemente do tempo decorrido após o clareamento, os valores de resistência adesiva entre resina e dentina foram reduzidos quando se utilizou perborato de sódio associado ao peróxido de hidrogênio ou à água.