Effects of liquid-to-solid ratio and gamma irradiation on the rheology and cytocompatibility of a beta-tricalcium phosphate-based injectable bone substitute.

Injectable bone substitute (IBS) materials are commonly used to fill irregular-shaped bone voids in non-load-bearing areas and can offer greater utility over those which are in prefabricated powder, granule, or block forms. This work investigates the impact of liquid-to-solid ratio (LSR) on the rheology and cytocompatibility of IBSs formulated from bioactive glass particles and ß-tricalcium phosphate (ß-TCP) in glycerol and poly(ethylene glycol) (PEG). IBS formulations of varying LSR were prepared and packed in 3 cc open-bore syringes and sterilized via gamma irradiation (10 kGy, 25 kGy). Gamma-irradiated formulations with high PEG content required the highest (73 N) mechanical force for injection from syringes. Oscillatory viscosity measurements revealed that the viscosity of samples was directly proportional to glycerol content. PEG and glycerol displayed competing effects on the washout resistance and cohesiveness of samples, which were based on total weight loss in media and Ca2+ ion release, respectively. Cell viability in 24-h extracts of 10 kGy gamma-sterilized and 25 kGy gamma-irradiated samples were 22.94% and 56.53%, respectively. The research highlights the complex interplay of IBS components on IBS rheology and, moreover, the cytotoxicity behaviors of beta-tricalcium phosphate-based injectable bone substitutes by in vitro experiments.

Surface channel patterned and endothelialized poly(glycerol sebacate) based elastomers.

Prevascularization of tissue equivalents is critical for fulfilling the need for sufficient vascular organization for nutrient and gas transport. Hence, endothelial cell culture on biomaterials is of great importance for researchers. Numerous alternate strategies have been suggested in this sense, with cell-based methods being the most commonly employed. In this study, poly (glycerol sebacate) (PGS) elastomers with varying crosslinking ratios were synthesized and their surfaces were patterned with channels by using laser ablation technique. In order to determine an ideal material for cell culture studies, the elastomers were subsequently mechanically, chemically, and biologically characterized. Following that, human umbilical vein endothelial cells (HUVECs) were seeded into the channels established on the PGS membranes and cultured under various culture conditions to establish the optimal culture parameters. Lastly, the endothelial cell responses to the synthesized PGS elastomers were evaluated. Remarkable cell proliferation and impressive cellular organizations were noticed on the constructs created as part of the investigation. On the concrete output of this research, arrangements in various geometries can be created by laser ablation method and the effects of various molecules, drugs or agents on endothelial cells can be evaluated. The platforms produced can be employed as an intermediate biomaterial layer containing endothelial cells for vascularization of tissue-engineered structures, particularly in layer-by-layer tissue engineering approaches.

Multi-layered in vitro 3D-bone model via combination of osteogenic cell sheets with electrospun membrane interlayer.

In this study, it was aimed to present an approach for the development of multi-layered tissue engineering constructs by using cell sheet engineering. Briefly, MC3T3-E1 mouse pre-osteoblast cells were cultured in temperature-responsive plates (Nunc Upcell®) in the presence of osteogenic medium and the resulting cell sheets were laminated with electrospun poly(L-lactic acid) (PLLA) membranes to obtain viable three-dimensional, thick constructs. The constructs prepared without PLLA membranes were used as control. The cell viability and death in the resulting structures were investigated by microscopic and colorimetric methods. The in vitro performance of the structures was discussed comparatively. Alkaline phosphatase (ALP) activity, collagen and sulfated glycosaminoglycan (sGAG) content values were calculated. The presented approach shows potential for engineering applications of complex tissues with at least two or more microenvironments such as osteochondral, corneal or vascular tissues.

Fabrication and characterization of carbon aerogel/poly(glycerol-sebacate) patches for cardiac tissue engineering.

Cardiovascular diseases (CVDs) are responsible for the major number of deaths around the world. Among these is heart failure after myocardial infarction whose latest therapeutic methods are limited to slowing the end-state progression. Numerous strategies have been developed to meet the increased demand for therapies regarding CVDs. This study aimed to establish a novel electrically conductive elastomer-based composite and assess its potential as a cardiac patch for myocardial tissue engineering. The electrically conductive carbon aerogels (CAs) used in this study were derived from waste paper as a cost-effective carbon source and they were combined with the biodegradable poly(glycerol-sebacate) (PGS) elastomer to obtain an electrically conductive cardiac patch material. To the best of our knowledge, this is the first report about the conductive composites obtained by the incorporation of CAs into PGS (CA-PGS). In this context, the incorporation of the CAs into the polymeric matrix significantly improved the elastic modulus (from 0.912 MPa for the pure PGS elastomer to 0.366 MPa for the CA-PGS) and the deformability (from 0.792 MPa for the pure PGS to 0.566 MPa for CA-PGS). Overall, the mechanical properties of the obtained structures were observed similar to the native myocardium. Furthermore, the addition of CAs made the obtained structures electrically conductive with a conductivity value of 65 × 10-3S m-1which falls within the range previously recorded for human myocardium. Thein vitrocytotoxicity assay with L929 murine fibroblast cells revealed that the CA-PGS composite did not have cytotoxic characteristics. On the other hand, the studies conducted with H9C2 rat cardiac myoblasts revealed that final structures were suitable for MTE applications according to the successes in cell adhesion, cell proliferation, and cell behavior.

Synthesis of Conductive Carbon Aerogels Decorated with ß-Tricalcium Phosphate Nanocrystallites.

There has been substantial interest in research aimed at conductive carbon-based supports since the discovery that the electrical stimulus can have dramatic effect on cell behavior. Among these carbon-aerogels decorated with biocompatible polymers were suggested as future materials for tissue engineering. However, high reaction temperatures required for the synthesis of the aerogels tend to impair the stability of the polymeric networks. Herein, we report a synthetic route towards carbon-aerogel scaffolds decorated with biocompatible ceramic nanoparticles of tricalcium phosphate. The composites can be prepared at temperature as high as 1100 °C without significant effect on the morphology of the composite which is comparable with the original aerogel framework. Although the conductivity of the composites tends to decrease with the increasing ceramic content the measured conductivity values are similar to those previously reported on polymer-functionalized carbon-aerogels. The cell culture study revealed that the developed constructs support cell proliferation and provide good cell attachment suggesting them as potentially good candidates for tissue-engineering applications.

Evaluation of collagen foam, poly(l-lactic acid) nanofiber mesh, and decellularized matrices for corneal regeneration.

Corneal tissue engineering efforts to obtain corneal tissue matrices through various types of materials for the replacement of damaged tissues. In this study, three different corneal constructs were prepared and evaluated in terms of morphological, optical, and biological characteristics. Type-I collagen was used to obtain collagen foam scaffolds through dehydrothermal crosslinking, while poly(l-lactic acid) (PLLA) was used to produce both random and aligned oriented electrospun corneal constructs. Bovine corneas were decellularized as third matrix. Software analyses showed that average pore size of collagen scaffolds was 88.207 ± 29.7 µm, while the average fiber diameter of aligned and random PLLA scaffolds were 0.69 ± 0.03 and 0.65 ± 0.03 µm, respectively. Degradation profiles revealed that collagen foam exhibits high degradation (20% mass loss) while electrospun PLLA scaffolds hold low degradation (9% mass loss) rates at day-28. Transmittance values of the obtained scaffolds were calculated as 92, 80, and 70% for collagen, PLLA, and decellularized cornea constructs, respectively. The evaluation of stromal keratocyte behavior on the constructs revealed that the cells exhibited their own morphology mostly on the aligned PLLA constructs, while they were mostly active on random PLLA electrospun corneal scaffolds. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 2157-2168, 2018.

Bi-layered constructs of poly(glycerol-sebacate)-ß-tricalcium phosphate for bone-soft tissue interface applications.

This study aims to establish a facile protocol for the preparation of a bi-layered poly(glycerol-sebacate) (PGS)/ß-tricalcium phosphate (ß-TCP) construct and to investigate its potential for bone-soft tissue engineering applications. The layered structure was prepared by distributing the ceramic particles within a prepolymer synthesized in a microwave reactor followed by a cross-linking of the final construct in vacuum (<10mbar). The vacuum stage led to the separation of cross-linked elastomer (top) and ceramic (bottom) phases. Results showed that addition of ß-TCP particles to the elastomer matrix after the polymerization led to an increase in compression strength (up to 14±2.3MPa). Tensile strength (σ), Young's modulus (E), and elongation at break (%) values were calculated as 0.29±0.03MPa and 0.21±0.03; 0.38±0.02 and 1.95±0.4; and 240±50% and 24±2% for PGS and PGS/ß-TCP bi-layered constructs, respectively. Morphology was characterized by using Scanning Electron Microscopy (SEM) and micro-computed tomography (µ-CT). Tomography data revealed an open porosity of 35% for the construct, mostly contributed from the ceramic phase since the elastomer side has no pore. Homogeneous ß-TCP distribution within the elastomeric structure was observed. Cell culture studies confirmed biocompatibility with poor elastomer-side and good bone-side cell attachment. In a further study to investigate the osteogenic properties, the construct were loaded with BMP-2 and/or TGF-ß1. The PGS/ß-TCP bi-layered constructs with improved mechanical and biological properties have the potential to be used in bone-soft tissue interface applications where soft tissue penetration is a problem.