A Histologic and Histomorphometric Evaluation of an Allograft, Xenograft, and Alloplast Graft for Alveolar Ridge Preservation in Humans: A Randomized Controlled Clinical Trial.

The aim of this study was to clinically evaluate the guided bone regeneration (GBR) potential of allograft, xenograft, and alloplastic materials in combination with resorbable membranes in extraction sockets. The qualitative and quantitative assessments of this prospective study were accomplished through histologic and histomorphometric analysis. Three experimental groups and 1 control group for comparison (n = 8) received either an allograft (human cancellous bone, freeze dried, Deutsches Institut für Zell und Gewebeersatz, Berlin, Germany), xenograft (BioOss, Geistlich Pharma AG, Wolhusen, Switzerland), or alloplast (biphasic calcium sulphate, Bondbone, MIS Implants Technologies Ltd., Charlotte, NC). The negative control group received no regenerative material. Tissue samples were then qualitatively and quantitatively evaluated as a function of percentage of new vital bone, graft particles content, soft tissue, and bone marrow over time. All 3 study groups presented bone volume suitable for the successful placement of a dental implant. The xenograft group yielded significantly less amount of vital bone compared with the allograft and alloplast groups. When comparing the percentage of residual graft particles, there was significantly greater amounts associated with the xenograft group in contrast to the allograft and alloplast groups. Similarly, a significantly increased amount of soft tissue percentage was observed within the xenograft group relative to all other groups. No significant differences were observed in the percentage of residual graft particles between the allograft and alloplast groups. There were also no significant differences detected in vital bone percentage between the allograft, alloplast, and control groups. When evaluating the bone marrow percentage, the only significant difference detected was between the xenograft and alloplast materials. Overall, no complications (ie, fever, malaise, purulence or fistula) were observed during the entirety of clinical trial among all patients. The greatest GBR potential was associated with the allograft material because of the greater degree of vital bone and the lowest percentage of residual graft particles. All studied bone substitute materials resulted in bone apposition for efficient use in alveolar ridge preservation procedures.

Effect of Surgical Instrumentation Variables on the Osseointegration of Narrow- and Wide-Diameter Short Implants.

PURPOSE: The aim of the present study was to systematically analyze how a multifactorial surgical instrumentation approach affects osseointegration on both narrow-diameter and wide-diameter short implants. MATERIALS AND METHODS: Twelve skeletally mature female sheep were used in the study along with 144 plateau-root-form healing chamber titanium (Ti-6Al-4V) implants (Bicon LLC, Boston, MA), evenly distributed between narrow (3.5 mm) and wide (6.0 mm) diameters. The presence or the absence of irrigation, different drilling speeds, and 2 time points quantifying bone-implant contact (BIC) and bone area fraction occupancy (BAFO) to evaluate the osteogenic parameters around the implants. RESULTS: There were no signs of inflammation, infection, or failure of the implants observed at either healing period. The narrow 3.5-mm implant, at 6 weeks, yielded significant differences in terms of BIC at a drilling speed of 50 rotations per minute (RPM), with higher values of the samples using irrigation (30.6 ± 6.1%) compared with those without (19.7 ± 6.1%). No statistical differences were detected for 500 and 1,000 RPM with or without irrigation. The wide 6-mm diameter implant showed differences with respect to drilling speed, 500 and 1,000 RPM, with higher values associated with samples subjected to irrigation. BAFO results, for both diameters, only detected statistical differences between the 2 times (3 vs 6 weeks); no statistical differences were detected when evaluating as a function of time, drilling speed, and irrigation. CONCLUSIONS: Surgical instrumentation variables (ie, drilling speed [RPM] and irrigation) yielded to be more of an effect for BIC at longer healing time (6 weeks) for the wider implants. Furthermore, deploying narrow or wide plateau-root-form implants, where conditions allow, has shown to be a safe alternative, considering the high BIC and BAFO values observed, independent of irrigation.

Parenchymal and stromal tissue regeneration of tooth organ by pivotal signals reinstated in decellularized matrix.

Cells are transplanted to regenerate an organs' parenchyma, but how transplanted parenchymal cells induce stromal regeneration is elusive. Despite the common use of a decellularized matrix, little is known as to the pivotal signals that must be restored for tissue or organ regeneration. We report that Alx3, a developmentally important gene, orchestrated adult parenchymal and stromal regeneration by directly transactivating Wnt3a and vascular endothelial growth factor. In contrast to the modest parenchyma formed by native adult progenitors, Alx3-restored cells in decellularized scaffolds not only produced vascularized stroma that involved vascular endothelial growth factor signalling, but also parenchymal dentin via the Wnt/ß-catenin pathway. In an orthotopic large-animal model following parenchyma and stroma ablation, Wnt3a-recruited endogenous cells regenerated neurovascular stroma and differentiated into parenchymal odontoblast-like cells that extended the processes into newly formed dentin with a structure-mechanical equivalency to native dentin. Thus, the Alx3-Wnt3a axis enables postnatal progenitors with a modest innate regenerative capacity to regenerate adult tissues. Depleted signals in the decellularized matrix may be reinstated by a developmentally pivotal gene or corresponding protein.

Biomaterial and biomechanical considerations to prevent risks in implant therapy.

This paper is aimed to present a biomaterials perspective in implant therapy that fosters improved bone response and long-term biomechanical competence from surgical instrumentation to final prosthetic rehabilitation. Strategies to develop implant surface texturing will be presented and their role as an ad hoc treatment discussed in light of the interplay between surgical instrumentation and implant macrogeometric configuration. Evidence from human retrieved implants in service for several years and from in vivo studies will be used to show how the interplay between surgical instrumentation and implant macrogeometry design affect osseointegration healing pathways, and bone morphologic and long-term mechanical properties. Also, the planning of implant-supported prosthetic rehabilitations targeted at long-term performance will be appraised from a standpoint where personal preferences (eg, cementing or screwing a prosthesis) can very often fail to deliver the best patient care. Lastly, the acknowledgement that every rehabilitation will have its strength degraded over time once in function will be highlighted, since the potential occurrence of even minor failures is rarely presented to patients prior to treatment.

Alveolar Ridge Expansion: Comparison of Osseodensification and Conventional Osteotome Techniques.

OBJECTIVE: The aim of this in vivo study is to compare the osseointegration of endosteal implants placed in atrophic mandibular alveolar ridges with alveolar ridge expansion surgical protocol via an experimental osseodensification drilling versus conventional osteotome technique. METHODS: Twelve endosteal implants, 4 mm × 13 mm, were placed in porcine models in horizontally atrophic mandibular ridges subsequent to prior extraction of premolars. Implants were placed with osseodensification drilling technique as the experimental group (n = 6) and osteotome site preparation as the control group (n = 6). After 4 weeks of healing, samples were retrieved and stained with Stevenel's Blue and Van Gieson's Picro Fuschin for histologic evaluation. Quantitative analysis via bone-to-implant contact (BIC%) and bone area fraction occupancy (BAFO%) were obtained as mean values with corresponding 95% confidence interval. A significant omnibus test, post-hoc comparison of the 2 drilling techniques' mean values was accomplished using a pooled estimate of the standard error with P-value set at 0.05. RESULTS: The mean BIC% value was approximately 62.5% in the osseodensification group, and 31.4% in the regular instrumentation group. Statistical analysis showed a significant effect of the drilling technique (P = 0.018). There was no statistical difference in BAFO as a function of drilling technique (P = 0.198). CONCLUSION: The combined osseodensification drilling-alveolar ridge expansion technique showed increased evidence of osseointegration and implant primary stability from a histologic and biomechanical standpoint, respectively. Future studies will focus on expanding the sample size as well as the timeline of the study to allow investigation of long-term prognosis of this novel technique.

Ridge Architecture Preservation Following Minimally Traumatic Exodontia Techniques and Guided Tissue Regeneration.

OBJECTIVE: To compare hard-tissue healing after 3 exodontia approaches. MATERIALS AND METHODS: Premolars of dogs were extracted: (1) flapless, (2) flap, and (3) flap + socket coverage with polytetrafluoroethylene (dPTFE) nonresorbable membrane (flap + dPTFE). Animals were euthanized at 1 and 4 weeks. Amount of bone formation within socket and socket total area were measured. RESULTS: Amount of bone formation revealed significant difference between 1 and 4 weeks; however, there was no differences among groups. Socket total area decreased after 4 weeks, and the flap + dPTFE group showed significantly higher socket total area. As a function of time and group, flap + dPTFE 4 weeks presented similar socket total area values relative to flap + dPTFE at 1 week, and significantly higher socket total area than flapless and flap. The histological sections revealed almost no bone formation within socket after 1 week, which increased for all groups at 4 weeks. CONCLUSION: Socket coverage with polytetrafluoroethylene (dPTFE) membrane showed to effectively preserve bone architecture. Bone formation within sockets was not influenced by tooth extraction technique.

Nanomechanical Assessment of Bone Surrounding Implants Loaded for 3 Years in a Canine Experimental Model.

PURPOSE: This work evaluated the nanomechanical properties of bone surrounding submerged and immediately loaded implants after 3 years in vivo. It was hypothesized that the nanomechanical properties of bone would markedly increase in immediately and functionally loaded implants compared with submerged implants. MATERIALS AND METHODS: The second, third, and fourth right premolars and the first molar of 10 adult Doberman dogs were extracted. After 6 months, 4 implants were placed in 1 side of the mandible. The mesial implant received a cover screw and remained unloaded. The remaining 3 implants received fixed dental prostheses within 48 hours after surgery that remained in occlusal function for 3 years. After sacrifice, the bone was prepared for histologic and nanoindentation analysis. Nanoindentation was carried out under wet conditions on bone areas within the plateaus. Indentations (n = 30 per histologic section) were performed with a maximum load of 300 µN (loading rate, 60 µN per second) followed by a holding and unloading time of 10 and 2 seconds, respectively. Elastic modulus (E) and hardness (H) were computed in giga-pascals. The amount of bone-to-implant contact (BIC) also was evaluated. RESULTS: The E and H values for cortical bone regions were higher than those for trabecular bone regardless of load condition, but this difference was not statistically significant (P > .05). The E and H values were higher for loaded implants than for submerged implants (P < .05) for cortical and trabecular bone. For the same load condition, the E and H values for cortical and trabecular bone were not statistically different (P > .05). The loaded and submerged implants presented BIC values (mean ± standard deviation) of 57.4 ± 12.1% and 62 ± 7.5%, respectively (P > .05). CONCLUSION: The E and H values of bone surrounding dental implants, measured by nanoindentation, were higher for immediately loaded than for submerged implants.

Effect of Obesity or Metabolic Syndrome and Diabetes on Osseointegration of Dental Implants in a Miniature Swine Model: A Pilot Study.

PURPOSE: The increasing prevalence of obesity or metabolic syndrome (O/MS) and type 2 diabetes mellitus (DM) remains a global health concern. Clinically relevant and practical translational models mimicking human characteristics of these conditions are lacking. This study aimed to demonstrate proof of concept of the induction of stable O/MS and type 2 DM in a Göttingen minipig model and validate both of these disease-adjusted Göttingen minipig models as impaired healing models for the testing of dental implants. MATERIALS AND METHODS: Nine minipigs were split into 3 groups-control (normal diet), obese (cafeteria diet), and diabetic (cafeteria diet plus low-dosage streptozotocin)-followed by placement of dental implants. Inflammatory markers including tumor necrosis factor α, C-reactive protein, and cortisol were recorded for each study group. Removal torque was measured, and histomorphometric analysis (bone-to-implant contact and bone area fraction occupancy) was performed. RESULTS: O/MS pigs showed, on average, a 2-fold increase in plasma C-reactive protein (P < .05) and cortisol (P < .09) concentrations compared with controls; DM pigs showed, on average approximately, a 40-fold increase in plasma tumor necrosis factor α levels (P < .05) and a 2-fold increase in cortisol concentrations (P < .05) compared with controls. The impact of O/MS and DM on implants was determined. The torque to interface failure was highest in the control group (200 N-cm) and significantly lower in the O/MS (90 N-cm) and DM (60 N-cm) groups (P < .01). Bone formation around implants was significantly greater in the control group than in the O/MS and DM groups (P < .02). CONCLUSIONS: Both O/MS and DM minipigs express a human-like disease phenotype, and both presented bone-healing impairment around dental implants. Our finding of no significant difference between type 2 DM and O/MS in bone formation around implants provides evidence that further investigation of the impact of O/MS is warranted.

In Silico Analysis of the Biomechanical Stability of Commercially Pure Ti and Ti-15Mo Plates for the Treatment of Mandibular Angle Fracture.

PURPOSE: To investigate the influence of different materials and fixation methods on maximum principal stress (MPS) and displacement in reconstruction plates using in silico 3-dimensional finite element analysis (3D-FEA). MATERIALS AND METHODS: Computer-assisted designed (CAD) models of the mandible and teeth were constructed. Champy and AO/ASIF plates and fixation screws were designed with CAD software. 3D-FEA was performed by image-based CAE software. Maximum and minimum values of biomechanical stability, MPS, and displacement distribution were compared in Champy and AO/ASIF plates made from commercially pure titanium grade 2 (cp-Ti) and a titanium-and-molybdenum (14.47% wt) alloy (Ti-15Mo). RESULTS: For plates fixed on a model of a fractured left angle of the mandible, the maximum and minimum values of MPS in the cp-Ti-constructed Champy plate, upper AO/ASIF plate, and lower AO/ASIF plate were 19.5 and 20.3%, 15.2 and 25.3%, and 21.4 and 4.6% lower, respectively, than those for plates made from Ti-15Mo. In the same model, the maximum and minimum values of displacement in the cp-Ti-constructed Champy plate, upper AO/ASIF plate, and lower AO/ASIF plate were 1.6 and 3.8%, 3.1 and 2.7%, and 5.4 and 10.4% higher, respectively, than those for plates made from Ti-15Mo. CONCLUSIONS: This in silico 3D-FEA shows that Ti-15Mo plates have greater load-bearing capability.

In Vivo Evaluation of Dual Acid-Etched and Grit-Blasted/Acid-Etched Implants With Identical Macrogeometry in High-Density Bone.

PURPOSE: Based on the current evidence, the effect of implant macrogeometry has a significant influence on osseointegration. Thus, this study evaluated histomorphometrically and histologically the bone response to acid-etched in comparison to grit-blasted/acid-etched (GB) and machined control (C) surfaced implants possessing identical macrogeometry placed in high-density bone. MATERIALS AND METHODS: Implant surface topography of the 3 different surfaced implants has previously been characterized. The macrogeometry of the implants were conical, and healing chambers were created in the cortical regions. The 3 groups were placed in the external mandibular body of adult male sheep (n = 5). After 6 weeks in vivo, all samples were retrieved for histologic observation and histomorphometry (eg, bone-to-implant contact [BIC] and bone area fraction occupancy [BAFO]). RESULTS: No statistical difference was observed for BIC and for BAFO, although there was a tendency that the mean values for BAFO was higher for the textured surface groups. CONCLUSIONS: It is suggested that the effect of surface topography is minimal in high-density bone and osseointegration seemed to be macrogeometry dependent.

Early Healing Evaluation of Commercially Pure Titanium and Ti-6Al-4V Presenting Similar Surface Texture: An In Vivo Study.

OBJECTIVE: This study evaluated the osseointegration of commercially pure titanium (Ti) grade-2 (G2) and Ti-6Al-4V alloy (G5) implants with the same geometry and surface treatment. MATERIALS AND METHODS: Thirty-six dental implants with a grit-blasted acid-etched surface were used (n = 18, each). Two implants, one per group, were installed in each subject, in the radius diaphysis (n = 18 beagle dogs), with interchanged fixture position (proximal-distal) between animals for a balanced number of devices per group and time in vivo (1, 3, and 6 weeks). RESULTS: Similar topographical parameters between G2 and G5 were observed for average surface roughness, root mean square, developed surface ratio, maximum height of surface, and density of summits. Removal torque was significantly higher for G5 than for G2. No differences were observed for bone-to-implant contact and bone-area-fraction occupancy. Removal torque significantly increased with time for both groups. At 1 week, new bone formation in direct contact with the implant surface and osteogenic tissue migration was observed with an increase in woven bone formation at 3 weeks followed by the onset of lamellar bone formation at 6 weeks. CONCLUSION: Although both surfaces were biocompatible and osteoconductive, increased removal torque was observed for Ti-6Al-4V compared with commercially pure Ti implants.

Scan-layered reconstructions: A pilot study of a nondestructive dental histoanatomical analysis method and digital workflow to create restorations driven by natural dentin and enamel morphology.

OBJECTIVE: This work aims to present a pilot study of a non-destructive dental histo-anatomical analysis technique as well as to push the boundaries of the presently available restorative workflows for the fabrication of highly customized ceramic restorations. MATERIALS AND METHODS: An extracted human maxillary central incisor was subject to a micro computed tomography scan and the acquired data was transferred into a workstation, reconstructed, segmented, evaluated and later imported into a Computer-Aided Design/Computer-Aided Manufacturing software for the fabrication of a ceramic resin-bonded prosthesis. RESULTS: The obtained prosthesis presented an encouraging optical behavior and was used clinically as final restoration. CONCLUSION: The digitally layered restorative replication of natural tooth morphology presents today as a clear possibility. New clinical and laboratory-fabricated, biologically inspired digital restorative protocols are to be expected in the near future. CLINICAL SIGNIFICANCE: The digitally layered restorative replication of natural tooth morphology presents today as a clear possibility. This pilot study may represent a stimulus for future research and applications of digital imaging as well as digital restorative workflows in service of esthetic dentistry.

Reliability and failure modes of narrow implant systems.

OBJECTIVES: Narrow implants are indicated in areas of limited bone width or when grafting is nonviable. However, the reduction of implant diameter may compromise their performance. This study evaluated the reliability of several narrow implant systems under fatigue, after restored with single-unit crowns. MATERIALS AND METHODS: Narrow implant systems were divided (n = 18 each), as follows: Astra (ASC); BioHorizons (BSC); Straumann Roxolid (SNC), Intra-Lock (IMC), and Intra-Lock one-piece abutment (ILO). Maxillary central incisor crowns were cemented and subjected to step-stress accelerated life testing in water. Use level probability Weibull curves and reliability for a mission of 100,000 cycles at 130- and 180-N loads (90 % two-sided confidence intervals) were calculated. Scanning electron microscopy was used for fractography. RESULTS: Reliability for 100,000 cycles at 130 N was ∼99 % in group ASC, ∼99 % in BSC, ∼96 % in SNC, ∼99 % in IMC, and ∼100 % in ILO. At 180 N, reliability of ∼34 % resulted for the ASC group, ∼91 % for BSC, ∼53 % for SNC, ∼70 % for IMC, and ∼99 % for ILO. Abutment screw fracture was the main failure mode for all groups. CONCLUSIONS: Reliability was not different between systems for 100,000 cycles at the 130-N load. A significant decrease was observed at the 180-N load for ASC, SNC, and IMC, whereas it was maintained for BSC and ILO. CLINICAL RELEVANCE: The investigated narrow implants presented mechanical performance under fatigue that suggests their safe use as single crowns in the anterior region.

Enhanced Bone Bonding to Nanotextured Implant Surfaces at a Short Healing Period: A Biomechanical Tensile Testing in the Rat Femur.

PURPOSE: To compare the bone bonding capabilities of 2 different surface treatments at an early healing period. Titanium alloy (Ti6Al4V) custom-made rectangular plates (1.4 × 2.4 × 4 mm) were either dual acid etched (Ti6Al4V-DAE) or DAE/nanotextured blasted (Ti6Al4V-NTB). MATERIALS AND METHODS: Implants were placed in the distal femurs of 10 Wistar rats and were allowed to heal for 9 days. After euthanasia, the bone immediately proximal and distal to the implant was removed to test the bone bonding force with a universal testing machine. Ultrastructure of the bone/implant interface was assessed by scanning electron microscopy. RESULTS: Ti6Al4V-NTB samples exhibited significantly greater bond strength than Ti6Al4V-DAE samples. Morphologically, the Ti6Al4V-NTB surfaces presented intimate interaction with bone, whereas little interaction between the Ti6Al4V-DAE surface and bone was observed. CONCLUSION: The results of this study indicated a significant increase in bone bonding for the DAE/nanotextured blasted surface, which is suggested to be the outcome of the nanotexturing.

Histomorphological and Histomorphometric Analyses of Grade IV Commercially Pure Titanium and Grade V Ti-6Al-4V Titanium Alloy Implant Substrates: An In Vivo Study in Dogs.

PURPOSE: To evaluate the bone response to grade IV commercially pure titanium (G4) relative to Ti-6Al-4V (G5). MATERIALS AND METHODS: Implant surface topography was characterized by optical interferometry and scanning electron microscopy (SEM). Thirty-six implants (Signo Vinces, n = 18 per group) were installed in the radius of 18 dogs. The animals were killed at 1, 3, and 6 weeks, resulting in 6 implants per group and time in vivo for bone morphology, bone-to-implant contact (BIC), and bone area fraction occupancy (BAFO) evaluation. RESULTS: SEM depicted a more uniform topography of G4 than G5. Surfaces were statistically homogeneous for Sa, Sq, and Sdr. At 1 week, new bone formation was observed within the healing connective tissue in contact with the implant surface. At 3 weeks, new bone in direct contact with the implant surface was observed at all bone regions. At 6 weeks, the healing chambers filled with woven bone depicted an onset of replacement by lamellar bone. No significant effect of substrate was detected. Time presented an effect on BIC and BAFO (P < 0.001). CONCLUSION: Both titanium substrates were biocompatible and osseoconductive at the bone tissue level.

Surface characterization and in vivo evaluation of laser sintered and machined implants followed by resorbable-blasting media process: A study in sheep.

BACKGROUND: This study aimed to compare the histomorphometric and histological bone response to laser-sintered implants followed by resorbable-blasting media (RBM) process relative to standard machined/RBM surface treated implants. MATERIAL AND METHODS: Six male sheep (n=6) received 2 Ti-6Al-4V implants (1 per surface) in each side of the mandible for 6 weeks in vivo. The histomorphometric parameters bone-implant contact (BIC) and bone area fraction occupancy (BAFO) were evaluated. RESULTS: Optical interferometry revealed higher Sa and Sq values for the laser-sintered/RBM surface in relation to standard/RBM implants. No significant differences in BIC were observed between the two groups (p>0.2), but significantly higher BAFO was observed for standard/RBM implants (p<0.01). CONCLUSIONS: The present study demonstrated that both surfaces were biocompatible and osseoconductive, and the combination of laser sintering and RBM has no advantage over the standard machined implants with subsequent RBM.

The Effect of Tissue Entrapment on Screw Loosening at the Implant/Abutment Interface of External- and Internal-Connection Implants: An In Vitro Study.

PURPOSE: To compare the removal of torque values of machined implant abutment connections (internal and external) with and without soft tissue entrapment using an in vitro model. MATERIALS AND METHODS: Thirty external- and 30 internal-connection implants were embedded in urethane dimethacrylate. Porcine tissue was prepared and measured to thicknesses of 0.5 and 1.0 mm. Six groups (n = 10) were studied: External- and internal-connection implants with no tissue (control), 0.5, and 1.0 mm of tissue were entrapped at the implant/abutment interface. Abutments were inserted to 20 Ncm for all six groups. Insertion torque values were recorded using a digital torque gauge. All groups were then immersed in 1 M NaOH for 48 hours to dissolve tissue. Subsequent reverse torque measurements were recorded. Mean and standard deviation were determined for each group, and one-way ANOVA and Bonferroni test were used for statistical analysis. RESULTS: All 60 specimens achieved a 20-Ncm insertion torque, despite tissue entrapment. Reverse torque measurements for external connection displayed a statistically significant difference (p < 0.05) between all groups with mean reverse torque values for the control (13.71 ± 1.4 Ncm), 0.5 mm (7.83 ± 2.4 Ncm), and 1.0 mm tissue entrapment (2.29 ± 1.4 Ncm) groups. Some statistically significant differences (p < 0.05) were found between internal-connection groups. In all specimens, tissue did not completely dissolve after 48 hours. CONCLUSIONS: External-connection implants were significantly affected by tissue entrapment; the thicker the tissue, the lower the reverse torque values noted. Internal-connection implants were less affected by tissue entrapment.

Influence of placement depth on bone remodeling around tapered internal connection implants: a histologic study in dogs.

OBJECTIVES: To evaluate the influence of implant-abutment interface (IAI) placement depth on bone remodeling around implants with two different types of tapered internal IAI: screwed-in (SI) and tapped-in (TI) connections in dogs. MATERIALS AND METHODS: Eight weeks post mandibular tooth extraction in six beagle dogs, two SI implants (OsseoSpeed(™), Astra Tech, DENTSPLY) and two TI implants (Integra-CP(™), Bicon LLC) were placed in one side of the mandible. The four experimental groups were as follows: (i) SI-placed equicrestally (SIC); (ii) TI-placed equicrestally (TIC); (iii) SI-placed 1.5 mm subcrestally (SIS); and (iv) TI-placed 1.5 mm subcrestally (TIS). Healing abutments were connected 12 weeks after implant placement. Sixteen weeks later, the dogs were sacrificed and histomorphometric analysis was performed. Histometrical outcomes were evaluated using a nonparametric Brunner-Langer model. RESULTS: Mean distance from the IAI to first bone-implant contact (IAI-fBIC) was 0.88 mm (median: 0.77; SD: 0.54) for SIC group, 1.23 mm (median: 1.22; SD: 0.66) for TIC group, 0.41 mm (median: 0.31; SD: 0.36) for SIS group, and 0.41 mm (median: 0.26; SD: 0.45) for TIS group. Subcrestal groups showed lower IAI-fBIC compared with equicrestal groups (P < 0.001). Connective tissue presented similar measurements regardless of the IAI placement depth and IAI type (P > 0.05), but the epithelium length and peri-implant soft tissue length in subcrestal groups were significant larger than that in the equicrestal groups (P < 0.001 and P = 0.004, respectively). CONCLUSION: Subcrestal implant placement with tapered internal IAI is beneficial for bone contact with the implant neck, and concurrently, it may not increase the soft tissue inflammation around IAI.

Osseointegration of Plateau Root Form Implants: Unique Healing Pathway Leading to Haversian-Like Long-Term Morphology.

Endosteal dental implants have been utilized as anchors for dental and orthopedic rehabilitations for decades with one of the highest treatment success rates in medicine. Such success is due to the phenomenon of osseointegration where after the implant surgical placement, bone healing results into an intimate contact between bone and implant surface. While osseointegration is an established phenomenon, the route which osseointegration occurs around endosteal implants is related to various implant design factors including surgical instrumentation and implant macro, micro, and nanometer scale geometry. In an implant system where void spaces (healing chambers) are present between the implant and bone immediately after placement, its inherent bone healing pathway results in unique opportunities to accelerate the osseointegration phenomenon at the short-term and its maintenance on the long-term through a haversian-like bone morphology and mechanical properties.

Evaluation of human periimplant soft tissues around nonsubmerged machined standard and platform-switched abutments.

PURPOSE: This study evaluated the effect of the platform-switching phenomenon, the use of a smaller diameter abutment on a larger diameter implant platform. Clinical and histological outcomes of the periimplant mucosa around titanium abutments in a nonsubmerged implant were evaluated. MATERIALS AND METHODS: Ten healthy adult patients, ranging from 27 to 65 years, participated in the study. A minimum of 2 endosseous implants with immediate abutment connection was placed per patient, 1 conventional and 1 platform-switched abutment. All sites for implant placement had an adequate zone of keratinized mucosa before surgical intervention. RESULTS: No clinical signs of inflammation were observed in the periimplant soft tissue mucosa, and healing was uneventful throughout the study period. Histological findings showed abnormally thick stratified squamous epithelium for both groups with few inflammatory cells in the connective tissue and none on the surface of the epithelium. CONCLUSION: Histological findings for both conventional and platform-switched implant-abutment configurations showed a similar composition of the soft tissue. These findings were in direct agreement with previous studies.