New classification for bone type at dental implant sites: a dental computed tomography study.

OBJECTIVE: This study proposed a new classification method of bone quantity and quality at the dental implant site using cone-beam computed tomography (CBCT) image analysis, classifying cortical and cancellous bones separately and using CBCT for quantitative analysis. METHODS: Preoperative CBCT images were obtained from 128 implant patients (315 sites). First, measure the crestal cortical bone thickness (in mm) and the cancellous bone density [in grayscale values (GV) and bone mineral density (g/cm3)] at the implant sites. The new classification for bone quality at the implant site proposed in this study is a "nine-square division" bone classification system, where the cortical bone thickness is classified into A: > 1.1 mm, B:0.7-1.1 mm, and C: < 0.7 mm, and the cancellous bone density is classified into 1: > 600 GV (= 420 g/cm3), 2:300-600 GV (= 160 g/cm3-420 g/cm3), and 3: < 300 GV (= 160 g/cm3). RESULTS: The results of the nine bone type proportions based on the new jawbone classification were as follows: A1 (8.57%,27/315), A2 (13.02%), A3 (4.13%), B1 (17.78%), B2 (20.63%), B3 (8.57%) C1 (4.44%), C2 (14.29%), and C3 (8.57%). CONCLUSIONS: The proposed classification can complement the parts overlooked in previous bone classification methods (bone types A3 and C1). TRIAL REGISTRATION: The retrospective registration of this study was approved by the Institutional Review Board of China Medical University Hospital, No. CMUH 108-REC2-181.

Biomechanical analysis of occlusal modes on the periodontal ligament while orthodontic force applied.

OBJECTIVE: The study objective was to investigate four common occlusal modes by using the finite element (FE) method and to conduct a biomechanical analysis of the periodontal ligament (PDL) and surrounding bone when orthodontic force is applied. MATERIALS AND METHODS: A complete mandibular FE model including teeth and the PDL was established on the basis of cone-beam computed tomography images of an artificial mandible. In the FE model, the left and right mandibular first premolars were not modeled because both canines required distal movement. In addition, four occlusal modes were simulated: incisal clench (INC), intercuspal position (ICP), right unilateral molar clench (RMOL), and right group function (RGF). The effects of these four occlusal modes on the von Mises stress and strain of the canine PDLs and bone were analyzed. RESULTS: Occlusal mode strongly influenced the distribution and value of von Mises strain in the canine PDLs. The maximum von Mises strain values on the canine PDLs were 0.396, 1.811, 0.398, and 1.121 for INC, ICP, RMOL, and RGF, respectively. The four occlusal modes had smaller effects on strain distribution in the cortical bone, cancellous bone, and miniscrews. CONCLUSION: Occlusal mode strongly influenced von Mises strain on the canine PDLs when orthodontic force was applied. CLINICAL RELEVANCE: When an FE model is used to analyze the biomechanical behavior of orthodontic treatments, the effect of muscle forces caused by occlusion must be considered.

Improving the prediction of the trabecular bone microarchitectural parameters using dental cone-beam computed tomography.

BACKGROUND: In this study, we explored how various preprocessing approaches can be employed to enhance the capability of dental CBCT to accurately estimate trabecular bone microarchitectural parameters. METHODS: In total, 30 bovine vertebrae cancellous bone specimens were used for in study. Voxel resolution 18-µm micro-computed tomography (micro-CT) and 100-µm dental CBCT were used to scan each specimen. Micro-CT images were used to calculate trabecular bone microarchitectural parameters; the results were set as the gold standard. Subsequently, before the dental CBCT images were converted into binary images to calculate trabecular bone microarchitectural parameters, three preprocessing approaches were used to process the dental CBCT images. For Group 1, no preprocessing approach was applied. For Group 2, images were sharpened and despeckable noises were removed. For Group 3, the function of local thresholding was added to Group 2 to form Group 3. For Group 4, the air pixels was removed from Group 3 to form Group 4. Subsequently, all images were imported into a software package to estimate trabecular bone microarchitectural parameters (bone volume fraction (BV/TV), trabecular thickness (TbTh), trabecular number (TbN), and trabecular separation (TbSp)). Finally, a paired t-test and a Pearson correlation test were performed to compare the capability of micro-CT with the capability of dental CBCT for estimating trabecular bone microarchitectural parameters. RESULTS: Regardless of whether dental CBCT images underwent image preprocessing (Groups 1 to 4), the four trabecular bone microarchitectural parameters measured using dental CBCT images were significantly different from those measured using micro-CT images. However, after three image preprocessing approaches were applied to the dental CBCT images (Group 4), the BV/TV obtained using dental CBCT was highly positively correlated with that obtained using micro-CT (r = 0.87, p < 0.001); the correlation coefficient was greater than that of Group 1 (r = -0.15, p = 0.412), Group 2 (r = 0.16, p = 0.386), and Group 3 (r = 0.47, p = 0.006). After dental CBCT images underwent image preprocessing, the efficacy of using dental CBCT for estimating TbN and TbSp was enhanced. CONCLUSIONS: Image preprocessing approaches can be used to enhance the efficacy of using dental CBCT for predicting trabecular bone microarchitectural parameters.

Intermittent parathyroid hormone improve bone microarchitecture of the mandible and femoral head in ovariectomized rats.

BACKGROUND: Intermittent parathyroid hormone (PTH) can be used to treat osteoporosis of the spine and hip. However, whether it can be used to treat osteoporosis of the mandible is unclear. The purpose of this study was to explore the influence of applying intermittent PTH to ovariectomized rats on the trabecular bone microarchitecture of the mandible and femoral head. METHODS: Eighteen female rats were divided into three groups: the healthy group, ovariectomized (OVX) group, and OVX + PTH group. The OVX group and OVX + PTH group had an OVX at 8 weeks of age. The OVX + PTH group received intermittent PTH therapy for 12 weeks. The mandibles and femurs of all rats were removed at 20 weeks and were then scanned using microcomputed tomography (micro-CT). RESULTS: From the micro-CT analysis, the trabecular bone microarchitecture of the mandible and femoral head are offered as follows: (1) The bone volume fraction and trabecular thickness in the OVX group were lower than those in the healthy group. (2) The bone volume fraction and trabecular thickness in the OVX + PTH group approximated those in the healthy group. CONCLUSION: The conclusions of this study regarding the trabecular bone microarchitecture of the mandible and femoral head are offered as follows: (1) The BV/TV and TbTh in the OVX group were lower than those in the healthy group. (2) The BV/TV and TbTh in the OVX + PTH group approximated those in the healthy group, therefore, intermittent PTH displayed high efficacy for treating femoral or mandibular deterioration of bone microstructure resulting from loss of ovarian function. Osteoporosis of the femur or mandible in the rats was ameliorated by intermittent PTH therapy.

New quantitative classification of the anatomical relationship between impacted third molars and the inferior alveolar nerve.

BACKGROUND: Before extracting impacted lower third molars, dentists must first identify the spatial relationship between the inferior alveolar nerve (IAN) and an impacted lower third molar to prevent nerve injury from the extraction. Nevertheless, the current method for describing the spatial relationship between the IAN and an impacted lower third molar is deficient. Therefore, the objectives of this study were to: (1) evaluate the relative position between impacted lower third molars and the IAN; and (2) investigate the relative position between impacted lower third molars and the IAN by using a cylindrical coordinate system. METHODS: From the radiology department's database, we selected computed tomography images of 137 lower third molars (from 75 patients) requiring removal and applied a Cartesian coordinate system by using Mimics, a medical imaging software application, to measure the distribution between impacted mandibular third molars and the IAN. In addition, the orientation of the lower third molar to the IAN was also measured, but by using a cylindrical coordinate system with the IAN as the origin. RESULTS: According to the Cartesian coordinate system, most of the IAN runs through the inferior side of the third molar (78.6 %), followed by the lingual side (11.8 %), and the buccal side (8.9 %); only 0.7 % is positioned between the roots. Unlike the Cartesian coordinate system, the cylindrical coordinate system clearly identified the relative position, r and θ, between the IAN and lower third molar. CONCLUSIONS: Using the cylindrical coordinate system to present the relationship between the IAN and lower third molar as (r, θ) might provide clinical practitioners with a more explicit and objective description of the relative position of both sites. However, comprehensive research and cautious application of this system remain necessary.

Influence of implant length and insertion depth on primary stability of short dental implants: An in vitro study of a novel mandibular artificial bone model.

Background/purpose: Dental implants are a mainstream solution for missing teeth. For the improvement of dental implant surface treatment and design, short dental implants have become an alternative to various complex bone augmentation procedures, especially those performed at the posterior region of both the maxilla and mandible. The objective of this study was to evaluate the effect of various insertion methods on the primary stability of short dental implants. Materials and methods: Commercial dental implants were inserted into artificial mandibular bone specimens using various insertion methods (equicrestal position, subcrestal position 1.5 mm, and lateral cortical anchorage) in accordance with an implant surgical guide. Insertion torque value (ITV) curves were recorded while implant procedures were performed. Both maximum ITVs (MITVs) and final ITVs (FITVs) were evaluated. Subsequently, Periotest values (PTVs) and implant stability quotients (ISQs) were measured for all specimens. A Kruskal-Wallis test was conducted to analyze the results for four primary stability parameters, and the Dunn test was used for a post hoc pairwise comparison when a difference was identified. Results: For all groups, their mean MITVs ranged from 33.6 to 59.4 N cm, whereas their mean FITVs ranged from 17.5 to 43.5 N cm. Insertion torque value, ISQ, and PTV decreased significantly when implants were inserted into subcrestal positions. When implants were inserted in the lateral bicortical position, the four aforementioned parameters yielded greater values. Conclusion: When 6-mm short implants were inserted in a lateral cortical anchorage position, high primary stability was yielded.

Preoperative assessment of bone density for dental implantation: a comparative study of three different ROI methods.

BACKGROUND: Dental cone beam computed tomography (CBCT) is commonly used to evaluate cancellous bone density before dental implant surgery. However, to our knowledge, no measurement approach has been standardized yet. This study aimed to evaluate the relationship between three different regions of interest (ROI) methods on cancellous bone density at the dental implant site using dental CBCT images. METHODS: Patients' dental CBCT images (n = 300) obtained before dental implant surgery were processed using Mimics (Materialise, Leuven, Belgium). At the potential implant sites, the rectangle, cylinder, and surrounding cylinder ROI methods were used to measure bone density. Repeated measures one-way analysis of variance was performed to compare the three ROI methods in terms of measurement results. Pearson correlation analysis was performed to identify the likely pair-wise correlations between the three ROI methods. RESULTS: The density value obtained using the surrounding cylinder approach (grayscale value [GV],523.56 ± 228.03) was significantly higher than the values obtained using the rectangle (GV, 497.04 ± 236.69) and cylinder (GV,493 ± 231.19) ROI methods in terms of results. Furthermore, significant correlations were noted between the ROI methods (r > 0.965; p < 0.001). CONCLUSIONS: The density measured using the surrounding cylinder method was the highest. The choice of method may not influence the trends of measurement results. TRIAL REGISTRATION: This study was approved by the Institutional Review Board of China Medical University Hospital, No. CMUH111-REC3-205. Informed consent was waived by the Institutional Review Board of China Medical University Hospital, CMUH111-REC3-205, owing to the retrospective nature of the study.

Effect of Implant Length and Insertion Depth on Primary Stability of Short Dental Implant.

Purpose: To evaluate the effect of insertion depth, bone type, and implant diameter on the primary stability of short implants. Materials and Methods: Commercial dental implants with different lengths (6 and 8 mm; BLX, Straumann) were inserted into artificial bone specimens of good and poor quality at three different depth positions: equicrestal, 1-mm subcrestal, and 2-mm subcrestal. Insertion torque values were recorded spontaneously during the implant procedure. Both maximum insertion torque values (MITVs) and final insertion torque values (FITVs) were recorded. Subsequently, Periotest values (PTVs) and implant stability quotients (ISQs) were measured for all specimens. Results: The mean MITVs of all groups ranged from 31.8 to 46.2 Ncm. However, the mean FITVs of all groups ranged from 8.8 to 29 Ncm. Torque values decreased significantly when the implants were inserted into their final positions. When insertion depth was increased, the PTV and ISQ decreased. Long implants and implants inserted into good-quality bone yielded greater primary stability, and bone quality appeared to have a greater effect on primary stability. Conclusion: When 6-mm short implants are inserted in a subcrestal position, low primary stability may be yielded, particularly in poor-quality bone.

Relation between insertion torque and bone-implant contact percentage: an artificial bone study.

OBJECTIVES: The purpose of this study was to determine the correlation between the peak insertion torque value (ITV) of a dental implant and the bone-implant contact percentage (BIC%). MATERIAL AND METHODS: Dental implants were inserted into specimens comprising a 2-mm-thick artificial cortical shell representing cortical bone and artificial foam bone representing cancellous bone with four densities (groups 1 to 4--0.32, 0.20, 0.16, and 0.12 g/cm(3)). Each specimen with an inserted implant was subjected to micro-computed tomography (micro-CT) scanning, from which the 3D BIC% values were calculated. Pearson's correlation coefficients (r) between the ITV and BIC% were calculated. RESULTS: The ITVs in groups 1 to 4 were 56.2 ± 4.6 (mean±standard deviation), 45.6 ± 0.9, 43.3 ± 4.3, and 38.5 ± 3.4 N cm, respectively, and the corresponding BIC% values were 41.5 ± 0.5%, 39.0 ± 1.0%, 30.8 ± 1.1%, and 26.2 ± 1.6%. Pearson's correlation coefficient between the ITV and BIC% was r = 0.797 (P < 0.0001). CONCLUSION: The initial implant stability, quantified as the ITV, was strongly positively correlated with the 3D BIC% obtained from micro-CT images. CLINICAL RELEVANCE: The ITV of a dental implant can be used to predict the initial BIC%; this information may provide the clinician with important information on the optimal loading time.

The Effects of Insertion Approach on the Stability of Dental Implants.

Dental implant surgery involves the insertion of a dental implant into the alveolar bone; the success of the surgery depends on the initial stability of the implant. The objective of this study was to examine the effects of dental implant insertion approaches in clinical surgery and in accordance with the standards of American Society for Testing and Materials on initial implant stability. Three insertion approaches were used for dental implant placement (Branemark Systems NobelSpeedy Groovy, Nobel Biocare AB, Gothenburg, Sweden) in two types of artificial bone-good bone (GB) and poor bone (PB). The three insertion approaches were as follows: (1) continuous rotation insertion (CRI): using a torque testing machine to continuously screw in an implant to completion and (2 and 3) intermittent rotation insertion (IRI)_90 and IRI_80: using CRI to bury an implant to 90% and 80% of its full length followed by IRI to complete the implantation, respectively. The maximum insertion torque value (ITV), periotest value (PTV), and implant stability quotient (ISQ) were measured and compared. The results indicated that bone quality and insertion approach both affected implant stability. Insertion approaches affected all three implant stability indicators differently in the GB and PB groups (p = 0.008). In GB groups, the insertion approach primarily affected ITV, whereas in PB groups, it primarily affected PTV. The effect of the insertion approach was less apparent for ISQ. Overall, in both the GB and PB groups, the implant stability for IRI_80 was greater than that for IRI_90, and the implant stability for IRI_90 was greater than that for CRI. Future in vitro studies should adopt an insertion approach that complies with the clinical practice for dental implant surgery. Dentists should adjust the timing for IRI in dental implant surgery to achieve greater initial dental implant stability.

Bone quality affects stability of orthodontic miniscrews.

The objective of this study was to evaluate the effect of bone-miniscrew contact percentage (BMC%) and bone quality and quantity on orthodontic miniscrew stability and the maximum insertion torque value (ITV). Orthodontic miniscrews of five different dimensions and several bovine iliac bone specimens were used in the evaluation. Miniscrews of each dimension group were inserted into 20 positions in bovine iliac bone specimens. The experiment was divided into three parts: (1) Bone quality and quantity were evaluated using cone-beam computed tomography (CBCT) and microcomputed tomography. (2) The 3D BMC% was calculated. (3) The ITVs during miniscrew insertion were recorded to evaluate the stability of the orthodontic miniscrews. The results indicated that longer and thicker miniscrews enabled higher ITVs. CBCT was used to accurately measure cortical bone thickness (r = 0.939, P < 0.05) and to predict the bone volume fraction of cancellous bone (r = 0.752, P < 0.05). BMC% was significantly influenced by miniscrew length. The contribution of cortical bone thickness to the ITV is greater than that of cancellous bone structure, and the contribution of cortical bone thickness to BMC% is greater than that of cancellous bone structure. Finally, the higher is BMC%, the greater is the ITV. This study concludes that use of CBCT may predict the mechanical stability of orthodontic miniscrews.

Effect of screw fixation on temporomandibular joint condylar prosthesis.

PURPOSE: The objective of the present study was to evaluate the effect of the number of screws on the stress and stability of the temporomandibular joint (TMJ) condylar prosthesis and on the strain distribution in the bone. MATERIALS AND METHODS: Three-dimensional, finite element models of the mandible and a TMJ condylar prosthesis with fixations involving different numbers of screws in 8 configurations were established to investigate the effect of the number of fixed screws on the stress and stability of the implant and strain in cortical and cancellous bone. RESULTS: The simulations showed that increasing the number of screws beyond 3 only slightly enhanced the implant stability and reduced the implant stress. The position of the inserted screws significantly affected the strain distributions in cortical and cancellous bone tissues. CONCLUSIONS: The results of our study have shown that 3 staggered screws can provide optimal implant stability and bone stress and strain distributions in a TMJ condylar prosthesis.

Can Male Patient's Age Affect the Cortical Bone Thickness of Jawbone for Dental Implant Placement? A Cohort Study.

Dental implants are among the most common treatments for missing teeth. The thickness of the crestal cortical bone at the potential dental implant site is a critical factor affecting the success rate of dental implant surgery. However, previous studies have predominantly focused on female patients, who are at a high risk of osteoporosis, for the discussion of bone quality and quantity at the dental implant site. This study aimed to investigate the effect of male patients' age on the crestal cortical bone of the jaw at the dental implant site by using dental cone-beam computed tomography (CBCT). This study performed dental CBCT on 84 male patients of various ages to obtain tomograms of 288 dental implant sites at the jawbone (41 sites in the anterior maxilla, 95 in the posterior maxilla, 59 in the anterior mandible, and 93 in the posterior mandible) for measuring the cortical bone thickness. A one-way analysis of variance and Scheffe's test were performed on the measurement results to compare the cortical bone thickness at implant sites in the four jaw areas. The correlation between male patient age and cortical bone thickness at the dental implant site was determined. The four jaw areas in order of the cortical bone thickness were as follows: posterior mandible (1.07 ± 0.44 mm), anterior mandible (0.99 ± 0.30 mm), anterior maxilla (0.82 ± 0.32 mm), and posterior maxilla (0.71 ± 0.27 mm). Apart from dental implant sites in the anterior and posterior mandibles, no significant correlation was observed between male patients' age and the cortical bone thickness at the dental implant site.

Assessment of the Retromolar Canal in Taiwan Subpopulation: A Cross-Sectional Cone-Beam Computed Tomography Study in a Medical Center.

The retromolar canal is an anatomical variation that occurs in the mandibular bone. The retromolar canal typically originates in the mandibular canal on the distal side of the third molar and extends forward and upward to the retromolar foramen (RMF), which contains the neurovascular bundle. Accidentally damaging the neurovascular bundle in the retromolar canal during the extraction of the third molar, dental implant surgery, or maxillofacial orthognathic surgery may lead to subsequent complications such as incomplete local anesthesia, paresthesia, and bleeding during operation. The objective of this study was to investigate the prevalence of the RMF in the Taiwanese population in a medical center by using dental cone-beam computed tomography (CBCT) and to identify the position of the RMF in the mandibular bone. The dental CBCT images for the mandibular bone of 68 hemi-mandible were uploaded to the medical imaging software Mimics 15.1 to determine the prevalence of the RMF in the Taiwanese population and the three positional parameters of the RMF in the mandibular bone: (1) The diameter of the RMF, (2) the horizontal distance from the midpoint of the RMF to the distal cementoenamel junction of the second molar, and (3) the vertical distance from the midpoint of the RMF to the upper border of the mandibular canal. Seven RMFs were observed in the 68 hemi-mandibles. Thus, the RMF prevalence was 10.3%. In addition, the diameter of the RMF was 1.41 ± 0.30 mm (mean ± standard deviation), the horizontal distance from the midpoint of the RMF to the distal cementoenamel junction of the the second molar was 12.93 ± 2.87 mm, and the vertical distance from the midpoint of the RMF to the upper border of the mandibular canal below second molar was 13.62 ± 1.3487 mm. This study determined the prevalence of the RMF in the Taiwanese population in a medical center and its relative position in the mandibular bone. This information can provide clinicians with a reference for posterior mandible anesthesia and surgery to ensure medical safety.

Relationship between Cortical Bone Thickness and Cancellous Bone Density at Dental Implant Sites in the Jawbone.

Dental implant surgery is a common treatment for missing teeth. Its survival rate is considerably affected by host bone quality and quantity, which is often assessed prior to surgery through dental cone-beam computed tomography (CBCT). Dental CBCT was used in this study to evaluate dental implant sites for (1) differences in and (2) correlations between cancellous bone density and cortical bone thickness among four regions of the jawbone. In total, 315 dental implant sites (39 in the anterior mandible, 42 in the anterior maxilla, 107 in the posterior mandible, and 127 in the posterior maxilla) were identified in dental CBCT images from 128 patients. All CBCT images were loaded into Mimics 15.0 to measure cancellous bone density (unit: grayscale value (GV) and cortical bone thickness (unit: mm)). Differences among the four regions of the jawbone were evaluated using one-way analysis of variance and Scheffe's posttest. Pearson coefficients for correlations between cancellous bone density and cortical bone thickness were also calculated for the four jawbone regions. The results revealed that the mean cancellous bone density was highest in the anterior mandible (722 ± 227 GV), followed by the anterior maxilla (542 ± 208 GV), posterior mandible (535 ± 206 GV), and posterior maxilla (388 ± 206 GV). Cortical bone thickness was highest in the posterior mandible (1.15 ± 0.42 mm), followed by the anterior mandible (1.01 ± 0.32 mm), anterior maxilla (0.89 ± 0.26 mm), and posterior maxilla (0.72 ± 0.19 mm). In the whole jawbone, a weak correlation (r = 0.133, p = 0.041) was detected between cancellous bone density and cortical bone thickness. Furthermore, except for the anterior maxilla (r = 0.306, p = 0.048), no correlation between the two bone parameters was observed (all p > 0.05). Cancellous bone density and cortical bone thickness varies by implant site in the four regions of the jawbone. The cortical and cancellous bone of a jawbone dental implant site should be evaluated individually before surgery.

Association between Age of Menopause and Thickness of Crestal Cortical Bone at Dental Implant Site: A Cross-Sectional Observational Study.

Satisfactory host bone quality and quantity promote greater primary stability and better osseointegration, leading to a high success rate in the use of dental implants. However, the increase in life expectancy as a result of medical advancements has led to an aging population, suggesting that osteoporosis may become a problem in clinical dental implant surgery. Notably, relative to the general population, bone insufficiency is more common in women with post-menopausal osteoporosis. The objective of this study was to compare the thickness of the crestal cortical bone at prospective dental implant sites between menopausal and non-menopausal women. Prospective dental implant sites in the jawbone were evaluated in two groups of women: a younger group (<50 years old), with 149 sites in 48 women, and an older group (>50 years old) with 191 sites, in 37 women. The thickness of the crestal cortical bone at the dental implant site was measured based on each patient's dental cone-beam computed tomography images. For both groups, one-way analysis of variance and Tukey's post-test were used to assess the correlation between cortical bone thickness and the presence of implants in the four jawbone regions. Student's t-test was further used to compare differences between the older and younger groups. From the retrospective study results, for both groups, thickness of the crestal cortical bone was the highest in the posterior mandible, followed by anterior mandible, anterior maxilla, and posterior maxilla. Compared with the younger group, the older group had a lower mean thickness of the crestal cortical bone. Among the four regions, however, only in the posterior maxilla was the crestal cortical bone significantly thinner in the older group than in the younger group.

Effect of Scanning Resolution on the Prediction of Trabecular Bone Microarchitectures Using Dental Cone Beam Computed Tomography.

Assessing bone quality and quantity at the location of dental implants before dental implantation is crucial. In recent years, dental cone-beam computed tomography (dental CBCT) has often been used to assess bone quality and quantity prior to dental implant. However, the effect of scanning resolution on the prediction of trabecular bone microarchitectural parameters (TBMPs) remains unclear. The objective of this study was to examine how dental CBCT with various scanning resolution differs with regard to predicting TBMPs. This study used micro-computed tomography (micro-CT) with 18 µm resolution and dental CBCT with 100 µm and 150 µm resolutions on 28 fresh bovine vertebrae cancellous bone specimens. Subsequently, all images were input into the ImageJ software to measure four TBMPs: bone volume total volume fraction (BV/TV), trabecular thickness (Tb.Th), trabecular number (Tb.N), and trabecular separation (Tb.Sp). One-way analysis of variance and Tukey's test were subsequently used to assess the differences between three scanning modes for the four TBMPs. In addition, correlations between measurement results obtained from micro-CT and dental CBCT with two resolutions were measured. The experimental results indicated that significant differences in four TBMPs were observed between micro-CT and dental CBCT (p < 0.05). The correlation coefficients between BV/TV, Tb.N, and Tb.Sp obtained from micro-CT and from dental CBCT with 100 µm resolution (0.840, 0.739, and 0.820, respectively) were greater than the correlation coefficients between BV/TV, Tb.N, and Tb.Sp obtained from micro-CT and from dental CBCT with 150 µm resolution (0.758, 0.367, and 0.724, respectively). The experimental results revealed that the TBMPs measured with dental CBCT with two resolutions differed from ideal values, but a higher resolution could provide more accurate prediction results, particularly for BV/TV, Tb.N, and Tb.Sp.

Static magnetic fields enhance dental pulp stem cell proliferation by activating the p38 mitogen-activated protein kinase pathway as its putative mechanism.

Dental pulp stem cells (DPSCs) can be a potential stem cell resource for clinical cell therapy and tissue engineering. However, obtaining a sufficient number of DPSCs for repairing defects is still an issue in clinical applications. Static magnetic fields (SMFs) enhance the proliferation of several cell types. Whether or not SMFs have a positive effect on DPSC proliferation is unknown. Therefore, the aim of this study was to investigate the effect of SMFs on DPSC proliferation and its possible intracellular mechanism of action. For methodology, isolated DPSCs were cultured with a 0.4-T SMF. Anisotropy of the lipid bilayer was examined using a fluorescence polarization-depolarization assay. The intracellular calcium ions of the SMF-treated cells were analysed using Fura-2 acetoxymethyl ester labelling. The cytoskeletons of exposed and unexposed control cells were labelled with actin fluorescence dyes. Cell viability was checked when the tested cells were cultured with inhibitors of ERK, JNK and p38 to discern the possible signalling cascade involved in the proliferative effect of the SMF on the DPSCs. Our results showed that SMF-treated cells demonstrated a higher proliferation rate and anisotropy value. The intracellular calcium ions were activated by SMFs. In addition, fluorescence microscopy images demonstrated that SMF-treated cells exhibit higher fluorescence intensity of the actin cytoskeletal structure. Cell viability and real-time polymerase chain reaction suggested that the p38 signalling cascade was activated when the DPSCs were exposed to a 0.4-T SMF. F-actin intensity tests showed that SB203580-treated cells decreased even with SMF exposure. Additionally, the F-/G-actin ratio increased due to slowing of the cytoskeleton reorganization by p38 mitogen-activated protein kinase inhibition. According to these results, we suggest that a 0.4-T SMF affected the cellular membranes of the DPSCs and activated intracellular calcium ions. This effect may activate p38 mitogen-activated protein kinase signalling, and thus reorganize the cytoskeleton, which contributes to the increased cell proliferation of the DPSCs. Copyright © 2016 John Wiley & Sons, Ltd.

Self-assembled micro-computed tomography for dental education.

This study used available or purchased equipment and an image reconstruction system developed by the college of dentistry to establish a basic self-assembled micro-computed tomography (micro-CT) system. Such a system would be suitable for teaching dental radiology to dental students. Specifically, it could help students to understand the principles governing dental cone-beam computed tomography (CBCT) and provide graduate students with a system for scanning small samples (e.g., individual teeth) during the early stages of research. The self-assembled micro-CT system was constructed using a portable dental X-ray tube, an intraoral digital X-ray detector, a high-precision rotation stage, related bracket accessories, and a notebook computer. Reconstructed images and three-dimensional models of the maxillary right third molar were produced using the self-assembled micro-CT system and an advanced commercially available micro-CT system (Skyscan 2211). Subsequently, the reconstructed images and 3D models produced using the two systems were compared by two senior dentists to determine whether considerable visual differences could be observed. Finally, the signal-to-noise ratio (SNR) was used for quantitative analysis and to compare the systems. Although the self-assembled micro-CT system produced image boundaries that were not as sharp as those of Skyscan 2211, the images were nonetheless remarkably similar. In addition, the two micro-CT systems produced 3D models that were almost identical in appearance and root canal shape. Quantitative analysis revealed that Skyscan 2211 had produced a SNR that was superior to that of the self-assembled micro-CT system, with the difference ranging from 36.77% to 136.22%; enamel, which has a higher density, exhibited lower SNR differences, whereas dentin, which has a lower density, exhibited higher SNR differences. The self-assembled micro-CT system with a resolution of 36 µm was created using a portable dental X-ray tube and an intraoral digital X-ray detector. Although the scanning time was relatively long (~30 min to scan images of a tooth), the images were adequate in the preliminary stage of experiments. More importantly, students were afforded the opportunity to observe the process of assembling and disassembling each component of a micro-CT scanner and thereby achieve a more comprehensive understanding of the principles governing micro-CT and dental CBCT.

Cortical Bone Morphological and Trabecular Bone Microarchitectural Changes in the Mandible and Femoral Neck of Ovariectomized Rats.

OBJECTIVE: This study used microcomputed tomography (micro-CT) to evaluate the effects of ovariectomy on the trabecular bone microarchitecture and cortical bone morphology in the femoral neck and mandible of female rats. MATERIALS AND METHODS: Twelve female Wister rats were divided into two groups: the control and ovariectomized groups. The rats in the ovariectomized group received ovariectomy at 8 weeks of age; all the rats were sacrificed at 20 weeks of age, and their mandibles and femurs were removed and scanned using micro-CT. Four microstructural trabecular bone parameters were measured for the region below the first mandibular molar and the femoral neck region: bone volume fraction (BV/TV), trabecular thickness (TbTh), trabecular separation (TbSp), and trabecular number (TbN). In addition, four cortical bone parameters were measured for the femoral neck region: total cross-sectional area (TtAr), cortical area (CtAr), cortical bone area fraction (CtAr/TtAr), and cortical thickness (CtTh). The CtTh at the masseteric ridge was used to assess the cortical bone morphology in the mandible. The trabecular bone microarchitecture and cortical bone morphology in the femoral necks and mandibles of the control group were compared with those of the ovariectomized group. Furthermore, Spearman's correlation (rs) was conducted to analyze the correlation between the osteoporosis conditions of the mandible and femoral neck. RESULTS: Regarding the trabecular bone microarchitectural parameters, the BV/TV of the trabecular bone microarchitecture in the femoral necks of the control group (61.199±11.288%, median ± interquartile range) was significantly greater than that of the ovariectomized group (40.329±5.153%). Similarly, the BV/TV of the trabecular bone microarchitecture in the mandibles of the control group (51.704±6.253%) was significantly greater than that of the ovariectomized group (38.486±9.111%). Furthermore, the TbSp of the femoral necks in the ovariectomized group (0.185±0.066 mm) was significantly greater than that in the control group (0.130±0.026mm). Similarly, the TbSp of the mandibles in the ovariectomized group (0.322±0.047mm) was significantly greater than that in the control group (0.285±0.041mm). However, the TbTh and TbN trends for the mandibles and femoral necks were inconsistent between the control and ovariectomized groups. Regarding the cortical bone morphology parameters, the TtAr of the femoral necks in the ovariectomized group was significantly smaller than that in the control group. There was no significant difference in the TtAr, CtAr, or CtTh of the femoral necks between the control and ovariectomized groups, and no significant difference in the CtTh of the mandibles between the control and ovariectomized groups. Moreover, the BV/TV and TbSp of the mandibles were highly correlated with those of the femurs (rs = 0.874 and rs = 0.755 for BV/TV and TbSp, respectively). Nevertheless, the TbTh, TbN, and CtTh of the mandibles were not correlated with those of the femoral necks. CONCLUSION: After the rats were ovariectomized, osteoporosis of the trabecular bone microarchitecture occurred in their femurs and mandibles; however, ovariectomy did not influence the cortical bone morphology. In addition, the parametric values of the trabecular bone microarchitecture in the femoral necks were highly correlated with those of the trabecular bone microarchitecture in the mandibles.