Effect of Real-Time Environment on Mechanical Properties of Preformed Stainless Steel Archwires: An In Vivo Study.

Introduction: Clinicians should be aware of any effect the oral environment may have on archwires. Laboratory models fail to closely imitate intraoral conditions. The aim was to evaluate the change in mechanical properties of preformed stainless steel archwires after 15 weeks of exposure to the oral environment. Methods: Three commercially manufactured 0.019 × 0.025″ stainless steel archwires were evaluated. Young's modulus, yield strength, spring factor, and hardness were studied. The unexposed distal end cuts (control samples) and archwires were tested after 15 weeks of intraoral exposure (test samples). Tension tests, Vickers microhardness tests, and nanoindentation tests were carried out. Results: Normality was tested using the Shapiro-Wilk test. Statistical analyses included the paired t-test for intragroup comparisons and Kruskal-Wallis ANOVA with the post hoc Dunn test for comparison of mean percentage reduction in values. At T15, Young's modulus showed a statistically significant decrease. Changes in yield strength and spring factor were not significant for groups other than American Orthodontics wires. The reduction in hardness was significant in 3M Unitek. Vickers, tension, and nanoindentation tests demonstrated an expansive range between hardness and Young's modulus so determined. Conclusion: 3M Unitek archwires showed the highest difference in Young's modulus. Yield strength values increased in Ortho Organizers archwires. Spring factor decreased only in 3M Unitek archwires. Hardness values obtained from various tests did not produce identical results.

Lip profile changes in patients with Class II Division 1 malocclusion of varied growth patterns treated with maxillary premolar extractions: A pilot study.

INTRODUCTION: This retrospective pilot study assessed the pre- and posttreatment lip profile changes among adult patients with Class II Division 1 malocclusion of varied growth patterns and compared these changes with patients with a skeletal Class I relationship, to identify the dental, skeletal, and soft tissue cephalometric variables that altered the posttreatment lip profile. METHODS: A total of 33 digital cephalograms were divided into 4 study groups based on the mandibular plane (Mp-SN) angle: group 1 (control, skeletal Class I; mean angle = 21.5°) (n = 8), group 2 (Class II Division 1 malocclusion; low angle = <26°) (n = 8), group 3 (Class II Division 1 malocclusion; intermediate angle = 26°-38°) (n = 9), and group 4 (Class II Division 1 malocclusion; high angle = >38°) (n = 8). RESULTS: We observed a significant decrease in SNA, ANB, maxillary incisor to NA (degrees and millimeters), and soft tissue parameters, especially lip strain and lower lip to E line and upper lip to E line. Posttreatment intergroup comparison showed a significant increase of Mp-SN, and this increase was greater in group 3, followed by group 4 as compared with group 1. In addition, statistically significant differences in SNA, ANB, mandibular incisor to NB (degrees) and IMPA, and H angle in groups 2-4 were observed. CONCLUSIONS: Patients with Class II Division 1 malocclusion showed a significant decrease in SNA, ANB, maxillary incisor to NA, and all soft tissue parameters in posttreatment compared with group 1. Thus, the soft tissue changes resulted in a similar profile to patients in group 1, who are considered to have an aesthetically pleasing posttreatment profile.

Effect of continuous vs sequential chelation on the mechanical properties of root dentin: An ex vivo study.

OBJECTIVES: To evaluate the mechanical properties of root canal dentin treated with sodium hypochlorite (NaOCl) in combination with hydroxyethylidene diphosphonic acid (HEDP) or ethylenediaminetetraacetic acid (EDTA). METHODS: For testing fracture resistance, 45 single-rooted teeth were instrumented and irrigated with NaOCl/HEDP, NaOCl/EDTA, or distilled water. Fifteen untreated teeth served as control. After obturation, specimens from the experimental groups were thermocycled, dynamically-loaded, and then statically-loaded in a universal testing machine until failure. For flexural strength analysis, 15 teeth were instrumented and irrigated with NaOCl/HEDP or NaOCl/EDTA. Root segments were sectioned into dentin bars and tested for flexural strength using a universal testing machine. For microhardness evaluation, 20 teeth were instrumented and irrigated with NaOCl/HEDP or NaOCl/EDTA. Dentin disks from the coronal-third of each root segment were prepared, one before and one after irrigation, for microhardness testing with a Knoop hardness tester. RESULTS: The highest fracture resistance was recorded in the untreated group, and the lowest in the EDTA group. Although the HEDP group had higher fracture resistance than the EDTA group, the distilled water group demonstrated even greater fracture resistance than the HEDP group. Specimens treated with HEDP had significantly higher flexural strength and microhardness values when compared with those treated with EDTA. CONCLUSION: The fracture resistance, flexural strength, and microhardness of root canal dentin were higher when root canals were irrigated with NaOCl/HEDP, when compared with NaOCl/EDTA. CLINICAL SIGNIFICANCE: Irrigating root canals with NaOCl combined with HEDP significantly improves the mechanical integrity of root canal dentin compared to the use of NaOCl with EDTA.