RESUMO
The coronal seal in root canal-treated teeth may be compromised depending on the accuracy of post space preparation and post cementation along with remaining gutta-percha. Root canal treatment can be compromised by endotoxins released by the coronal bacteria as a result of microleakage. The study was conducted by undergraduate students to measure the gap between the cemented post and residual gutta-percha. In total, 217 endodontically treated teeth were evaluated with intraoral peri-apical radiographs. Based on the intraoral periapical radiographic examination in the CS-R4 program, Group I had no gap, Group II had a gap of >0 to 2 mm, and Group III had a gap of more than 2 mm between the end of the cemented post and the remaining gutta-percha. In total, 40% (n = 87) of the teeth had no gap, 59% (127) had a gap of >0 to 2 mm, and 1% (n = 3) had a gap of more than 2 mm between the cemented post end and remaining gutta. Chi square test revealed a significant difference in the gap between the post and remaining gutta-percha between males and females students (p < 0.001). In terms of the gap between the cemented post end and the residual gutta-percha, the root canal treated teeth with post and core by undergraduates were clinically acceptable.
Assuntos
Materiais Restauradores do Canal Radicular , Dente não Vital , Humanos , Guta-Percha , Estudos Transversais , Estudos RetrospectivosRESUMO
This Systematic Review (SR) was to report on the prevalence of pulp stones in the Saudi Arabian (KSA) population. The electronic databases were searched for scientific research articles during May 2021. The data search was performed in electronic search engines like PubMed, Scopus, Web of science, and Saudi Digital Library, and 6 original research articles which fulfilled the eligibility criteria were assessed for qualitative data. The prevalence of pulp stones among the KSA population ranged from 4.6% to 50.93% among the study participants and it ranged between 10.2%-13.34% in the teeth assessed. The pulp stones were more frequently reported in decayed teeth, periodontal diseases, attrition, teeth with dental restorations, and higher in the molar teeth in comparison with the premolar teeth. The data on the prevalence of pulp stones among the Saudi population will be helpful for clinicians in planning endodontic procedures.
RESUMO
The aim of this study is to investigate the combined effect of a digital manufacturing technique (subtractive vs. additive), preparation taper (10° vs. 20° TOC), and finish line (chamfer vs. shoulder) on the marginal adaptation of temporary crowns following cementation with a compatible temporary cement. Four mandibular first molar typodont teeth were prepared for full coverage crowns with standard 4 mm preparation height as follows: 10° TOC with the chamfer finish line, 10° TOC with the shoulder finish line, 20° TOC with the chamfer finish line and 20° TOC with the shoulder finish line. Each of the four preparation designs were subdivided into two subgroups to receive CAD/CAM milled and 3D-printed crowns (n = 10). A total of 80 temporary crowns (40 CAD/CAM milled and 40 3D-printed) were cemented to their respective die using clear temporary recement in the standard cementation technique. The samples were examined under a stereomicroscope at ×100 magnification following calibration. Linear measurements were performed at seven equidistant points on each axial surface and five equidistant points on each proximal surface. One-way ANOVA analysis and Tukey HSD (Honestly Significance Difference) were performed. The best marginal fit was seen in group 8, while the poorest fit was noted in group 2. Shoulder finish lines and 10° TOC resulted in higher marginal gaps, especially in CAD/CAM milled group. The selection of 3D-printed crowns may provide a better marginal fit within the range of clinical acceptability. Marginal gaps were within clinical acceptability (50 and 120 µm) in all groups except group 2.
RESUMO
BACKGROUND: The clinical success of post-core restorations is determined by the composite utilized and the strength of the post-core adhesion. The effectiveness of titanium dioxide nanoparticles (TiO2 NPs) as a multifunctional material with photo-induced activities and better mechanical characteristics are observed as particle size is reduced to under 50 nm. AIM: The purpose of this study is to determine the bond strength of fibre-reinforced composite (FRC) posts with TiO2 NP as fillers and to compare it with conventional composite resin core material. MATERIALS AND METHODS: 30 single-rooted mandibular premolars were selected and routine root canal procedures were done. A quantity of 5% TiO2 NPs were synthesized and added as silanized filler to the experimental composite resin. Post space was prepared and fibre-reinforced composite (FRC) post luting was performed. The specimens were then grouped into the following groups: Group I consisted of the experimental composite resin containing 5% TiO2 fillers, Group II consisted of core X flow, and Group III consisted of Multicore Flow. All test groups were submitted for thermocycling. After this, the samples were tested for micro tensile bond strength. A stereomicroscope with a magnification of 20× was used to examine the fractured surfaces. The data were analysed using one-way ANOVA and Tukey HSD tests. RESULTS: Statistical analysis revealed that Group I showed the highest mean bond strength value of 35.6180 Mpa. The results obtained with Group III showed the lowest mean bond strength value of 19.4690 Mpa. Adhesive failures were identified by stereomicroscopy of the fractured surfaces. CONCLUSION: The experimental composite resin comprising 5% TiO2 NP had a greater bond to the FRC post than other materials tested.