How Does Ambient Light Affect the Image Quality of Phosphor Plate Digital Radiography? A Quantitative Analysis Using Contemporary Digital Radiographic Systems.

The aim of this study is to quantitatively evaluate the influence of the duration of ambient light exposure on the image quality of digital radiographs obtained with contemporary phosphor plate (PSP)-based systems. Radiographs of an aluminum step-wedge were obtained using VistaScan and Express systems at five X-ray exposure times: 0.10, 0.20, 0.32, 0.40, and 0.50 s; the resulting dose-area products were, respectively, 21.93, 43.87, 70.19, 87.75, and 109.6 mGycm2. Before PSP read-out, half of the sensitive surface of the PSP plates was exposed to ambient light for 5, 10, 30, 60, and 90 s. The effect of light exposure on brightness, contrast, contrast-to-noise ratio (CNR), signal-to-noise ratio (SNR), and image saturation was compared using ANOVA with the Tukey test (α = 0.05). Ambient light exposure increased brightness and contrast and reduced CNR and SNR in PSP-based radiographs of contemporary digital systems. At the longest X-ray exposure times, ambient light exposure reduced the dark saturation (mean gray values ≤ 1) observed in Express. In conclusion, the negative effects of ambient light observed on the image quality of PSP-based radiographs are directly proportional to the duration of exposure. Clinicians should be aware of such harmful effects when handling and scanning PSP plates in bright environments.

Dentomaxillofacial CBCT: Clinical Challenges for Indication-oriented Imaging.

This critical review discusses the clinical challenges for patient-specific and indication-oriented dentomaxillofacial cone beam computed tomography (CBCT). Large variations among units and protocols may lead to variable degrees of diagnostic and three-dimensional model accuracy, impacting both specific diagnostic tasks and treatment planning. Particular indications, whether diagnostic or therapeutic, may give rise to very specific challenges with regard to CBCT unit and parameter setup, considering the required image quality, segmentation accuracy, and artifact level. Considering that dental materials are in the field of view needed for diagnosis or treatment planning, artifact expression is a dominant factor in proper CBCT selection. The heterogeneity of dental CBCT units and performances may highly impact the scientific results. Thus research findings cannot be simply generalized as published evidence, and a demonstrated clinical applicability for a specific indication should not be simply extrapolated from one CBCT unit to another.

Effect of a metal artifact reduction algorithm on dehiscence and fenestration detection around zirconia implants with cone beam computed tomography.

OBJECTIVE: To assess the efficacy of the metal artifact reduction algorithm (MARA) of the Cranex 3D cone beam computed tomography (CBCT) device in the detection of peri-implant dehiscence and fenestration around zirconia implants. STUDY DESIGN: In total, 60 implants were placed in bovine ribs. Dehiscence and fenestration defects were created around the implants, after which 60 CBCT images were obtained with and 60 without activation of MARA. Three radiologists examined the images for the presence of defects. The area under the curve (AUC) from receiver operating characteristic analysis, sensitivity, and specificity were calculated to assess the ability to discriminate the presence vs absence of bone defects. One-way analysis of variance was employed to analyze outcome measures. The significance level was established at 5% (α = 0.05). RESULTS: AUC values indicated excellent discrimination of dehiscence on images with MARA activation and an excellent to outstanding range of discrimination with MARA deactivation. For fenestration, MARA activation and deactivation both led to outstanding discrimination. Sensitivity and specificity values revealed that activation of MARA was helpful in distinguishing the presence vs. absence of dehiscence, while both MARA conditions were helpful for fenestration. However, there were no statistically significant differences between MARA activation and deactivation for any outcome measure (P >.05). CONCLUSION: CBCT is suitable for detecting peri-implant defects, but MARA application does not significantly affect peri-implant dehiscence and fenestration detection.

Image quality for visualization of cracks and fine endodontic structures using 10 CBCT devices with various scanning protocols and artefact conditions.

The aim of this study was to evaluate CBCT exposure protocols and CBCT devices in terms of image quality for the detection of cracks and fine endodontic structures using 3 conditions of metallic artifacts. An anthropomorphic phantom containing teeth with cracks, isthmus, narrow canal, and apical delta was scanned using ten CBCT devices. A reference industrial CT image was used to detect and measure all structures. Three conditions were created: (1) metal-free, (2) 'endo' and (3) 'implant' with metallic objects placed next to the teeth of interest. For each condition, three protocols were selected: medium field of view (FOV) standard resolution, small FOV standard and high resolution. The results showed that only small FOV high-resolution metal-free images from two devices (A and H) were appropriate to visualize cracks. For fine structure identification, the best result was observed for small FOV high resolution. However, the visualization significantly worsened in the presence of metallic artefacts. The ability of CBCT images for visualizing cracks is restricted to certain CBCT devices. Once metallic artefacts are present, crack detection becomes unlikely. Overall, small FOV high-resolution protocols may allow detection of fine endodontic structures as long as there are no high-dense objects in the region of interest.

Evaluation of the combined assessment of two digital enhancement filters in periapical radiographs obtained with different projection angles in the detection of simulated dental root fractures.

OBJECTIVE: To evaluate the diagnostic efficacy of the combined assessment of the original radiographic image with the Invert or Emboss digital enhancement filters in periapical radiographs obtained with different horizontal projection angles in the detection of simulated dental root fracture. MATERIALS AND METHODS: Thirty-four single-rooted teeth were selected, out of which 17 teeth were subjected to root fracture. Each tooth was individually placed in an empty socket of a dry human maxilla or mandible and X-rayed following the paralleling technique at three horizontal projections: mesial, right angle, distal. Then, the Invert and Emboss enhancement filters were applied. Five examiners independently evaluated all the images and rated the fractures using a 5-point scale. Weighted kappa test assessed the intra- and interexaminer agreements. Diagnostic values were calculated and the areas under the receiver operating characteristic curve (AUC) were compared using two-way ANOVA with Tukey test as post hoc (α = 0.05). RESULTS: The inter- and intraexaminer agreement ranged from moderate to almost perfect and from substantial to almost perfect, respectively. Diagnostic values were considerably high for all conditions with no significant difference between the AUC values (p > 0.05). CONCLUSIONS: The combined use of the original radiographic image with the Invert or Emboss digital enhancement filters in periapical radiographs obtained with different projection angles did not influence the detection of simulated dental root fracture.

Influence of working length and anatomical complexities on the apical root canal filling: a nano-CT study.

The present study aimed to compare the filled volume by gutta-percha and sealer in the apical region of the main canal and ramifications, after instrumentation at two different working lengths using nano-computed tomography (nano-CT). Twenty-two premolars with apical ramifications were selected after micro-computed tomography evaluation and were randomly divided into groups for further endodontic instrumentation at two different working lengths: G1 - Root canals shaped 1 mm short of the apical foramen (n=11), and G2 - Root canals shaped at the apical foramen (n=11). After completing root treatment, nano-CT images were acquired, and the filled volume by gutta-percha and sealer in the main canal apical 0-4 mm and 0-1 mm ranges, and apical ramifications were objectively measured by an operator specialized in both radiology and endodontics, blinded for both groups. The Mann-Whitney test was applied to compare both groups regarding the filling of the main canal apical ranges and apical ramifications with a significance level of 5% (α ≤ 0.05). It was observed that root canals shaped at the apical foramen had a larger volume of the main canal filled than root canals shaped 1 mm short of the apical foramen, at both apical ranges (0-4 and 0-1 mm) (p<0.05). Regarding the filling of the apical ramifications, there was no significant difference between groups (p>0.05). In conclusion, the root canals shaped at apical foramen exhibited increased filling volume of the main canal in the apical region. However, neither of both working lengths influenced filling of the apical ramifications.

Combined Use of 2 Cone-beam Computed Tomography Scans in the Assessment of Vertical Root Fracture in Teeth with Intracanal Material.

INTRODUCTION: The purpose of this preliminary study was to evaluate the diagnostic accuracy of the combined use of 2 cone-beam computed tomographic (CBCT) volumes obtained with the tooth of interest positioned at different orientations in the detection of vertical root fracture (VRF). METHODS: Thirty single-rooted teeth were divided into 2 main groups (n = 15): control and with VRF. The teeth were individually placed in a phantom composed of a human skull and mandible, which was CBCT scanned in 2 spatial orientations: conventional (with the Frankfurt plane parallel to the floor) and angled acquisition (tilted 90° backward). Also, each tooth was scanned with gutta-percha, a metal post, and without any intracanal material. Three oral radiologists individually evaluated the images resulting from conventional acquisition and verified the presence or absence of VRF (conventional CBCT assessment), setting a score on a 5-point scale. Subsequently, the observers evaluated both images resulting from the conventional and angled acquisitions (combined CBCT assessment). The diagnostic values of the conventional and combined assessments were compared using 2-way analysis of variance with the post hoc Tukey test. The significance level was set at 5% (α = 0.05). RESULTS: The combined CBCT assessment showed higher accuracy and sensitivity in the VRF diagnosis of teeth filled with gutta-percha (P < .05). In teeth with a metal post, all diagnostic values were higher in the combined CBCT assessment (P < .05). CONCLUSIONS: This preliminary study suggests that the CBCT-based diagnosis of VRF in teeth with intracanal material was improved when the assessment combines images obtained at 2 orientations.

Impact of the blooming artefact on dental implant dimensions in 13 cone-beam computed tomography devices.

BACKGROUND: The purpose of this study was to objectively assess dimensional alteration (blooming artefact) on dental implant using 13 cone-beam computed tomography (CBCT) devices adjusted to device-specific scanning protocols and to assess whether subjective adjustment of brightness and contrast (B&C) could alter its visualization. METHODS: An anthropomorphic phantom containing a dental implant was scanned in 13 CBCT devices adjusted to three scanning protocols: medium-FOV standard resolution, small-FOV standard resolution, and small-FOV high resolution. The diameter of the implant was measured at five levels, averaged, and compared with those from a reference standard industrial CT image. B&C adjustments were performed and measurements were repeated. The intraclass correlation coefficient assessed the reliability of the measurements and general linear mixed models were applied for multiples comparisons at a 95% confidence interval. RESULTS: Implant diameter obtained from small-FOV high-resolution protocols in most CBCT devices was not significantly different when compared to that from the reference (p > 0.05). For standard protocols, significant dimensional alteration of the implant ranging from 23 to 34% (0.67 to 1.02 mm) was observed in 9 CBCT devices for small-FOV scanning (p < 0.05), and in 8 CBCT devices for medium-FOV scanning, implant dimensional alteration ranged significantly from 21 to 35% (0.62 to 1.04 mm). After B&C adjustments, dimensional alteration was reduced for several of the CBCT devices tested (p < 0.05). CONCLUSIONS: The visualization of the implant dimensional alteration differed between CBCT devices and scanning protocols with an increase in diameter ranging from 0.27 to 1.04 mm. For most CBCT devices, B&C adjustments allowed to reduce visualization of implant blooming.

Evaluation of 10 Cone-beam Computed Tomographic Devices for Endodontic Assessment of Fine Anatomic Structures.

INTRODUCTION: The purpose of this study was to classify 10 cone-beam computed tomographic (CBCT) devices using a ranking model according to the detection of fine endodontic structures. METHODS: A dedicated dentate anthropomorphic phantom was scanned 2 times using 10 CBCT devices without any metal (metal-free condition) and with an endodontically treated tooth containing a metallic post (metal condition). A reference image acquired on an industrial micro-CT scanner was used to register all CBCT images, yielding corresponding anatomic slices. Afterward, 3 experienced observers assessed all acquired CBCT images for their ability to assess a narrow canal, isthmus, and apical delta ramification using a categoric rank from 1 (best) to 10 (worst). Fleiss kappa statistics were used to calculate intra- and interobserver agreements for each CBCT device separately. Based on the observers' scores, general linear mixed models were applied to compare image quality among different CBCT devices for performing endodontic diagnostic tasks (α = .05). RESULTS: The 10 CBCT devices performed differently for the evaluated endodontic tasks (P < .05), with 3 devices performing better for endodontic feature detection. Yet, in the presence of metal, only 2 devices were able to keep a high level of endodontic feature detection. CONCLUSIONS: The evaluated endodontic tasks were CBCT device dependent, and their detection was influenced by the presence of metal.

Assessment of Ramifications in the Apical Region of Root Canals: A Micro-CT Study in a Brazilian Population.

The present study used microcomputed tomography (micro-CT) images to assess the prevalence, number, and location of apical ramifications (ARs) in the root canals of different dental groups in a Brazilian population. Three hundred and sixty-seven extracted human teeth, totaling 475 roots, were scanned by micro-CT at 19.6 µm spatial resolution. The obtained images were evaluated by two observers in consensus, and a descriptive analysis was performed to verify the prevalence, number, and location of ARs in each dental group. Chi-square test was used to compare the prevalence of ARs in different types of roots, and one-way analysis of variance compared the number of ARs in the apical 1 mm, 2 mm, and 3 mm of the root. Significance level was established at 5% (α=0.05). ARs were present in 253 (53.3%) of the 475 roots evaluated. A total of 607 ARs were detected, with the vast majority (530) located at one and two millimeters from the main foramen. The highest prevalence of ARs was observed in maxillary canines (65%); maxillary premolars - single-rooted (83.3%), buccal root (80%), and palatine root (73.3%); mandibular premolars (64.2%); mesiobuccal root of maxillary molars (76.6%); and mesial root of mandibular molars (66.6%). For the Brazilian population, most of the ARs are located in the apical 1 and 2 mm of the root, with greater prevalence in the posterior teeth and maxillary canines. These findings suggest the need for additional attention while planning endodontic treatments, including strategies to effectively clean and fill the apical region.

Influence of Tooth Orientation on the Detection of Vertical Root Fracture in Cone-beam Computed Tomography.

INTRODUCTION: The purpose of this study was to assess the influence of tooth orientation in relation to the projection plane of the x-rays on the detection of vertical root fracture (VRF) with different filling materials using cone-beam computed tomographic (CBCT) imaging. METHODS: Thirty single-rooted human teeth were endodontically instrumented, and VRF was induced in half of the sample. The roots were individually placed in the dental socket of a phantom head composed of a dry human skull and mandible, and CBCT images were obtained of each root with the longitudinal axis in 2 orientations: perpendicular and parallel to the projection plane of the x-rays. Also, each root was scanned under 3 filling conditions: without filling material, with gutta-percha, and with a metal post. Radiation doses at specific anatomic regions of the phantom were obtained for the 2 orientations. Five radiologists evaluated all images and rated the fractures on a 5-point scale. The sensitivity, specificity, accuracy, and positive and negative predictive values were calculated. The area under the receiver operating characteristic curve and the dosimetric outcomes for each root orientation and filling material were compared, respectively, with 2-way and 1-way analysis of variance with the post hoc Tukey test (α = 0.05). RESULTS: There was no significant difference (P ≥ .05) in the detection of VRF between root orientations regardless of the filling material. Az values were significantly lower (P < .05) in the presence of gutta-percha and a metal post. The root orientation varied the absorbed dose at some anatomic regions. CONCLUSIONS: The orientation of the tooth in relation to the projection plane of the x-rays does not influence the detection of VRF using CBCT imaging irrespective of the intracanal material.

Influence of working length and anatomical complexities on the apical root canal filling: a nano-CT study

Abstract The present study aimed to compare the filled volume by gutta-percha and sealer in the apical region of the main canal and ramifications, after instrumentation at two different working lengths using nano-computed tomography (nano-CT). Twenty-two premolars with apical ramifications were selected after micro-computed tomography evaluation and were randomly divided into groups for further endodontic instrumentation at two different working lengths: G1 - Root canals shaped 1 mm short of the apical foramen (n=11), and G2 - Root canals shaped at the apical foramen (n=11). After completing root treatment, nano-CT images were acquired, and the filled volume by gutta-percha and sealer in the main canal apical 0-4 mm and 0-1 mm ranges, and apical ramifications were objectively measured by an operator specialized in both radiology and endodontics, blinded for both groups. The Mann-Whitney test was applied to compare both groups regarding the filling of the main canal apical ranges and apical ramifications with a significance level of 5% (α ≤ 0.05). It was observed that root canals shaped at the apical foramen had a larger volume of the main canal filled than root canals shaped 1 mm short of the apical foramen, at both apical ranges (0-4 and 0-1 mm) (p<0.05). Regarding the filling of the apical ramifications, there was no significant difference between groups (p>0.05). In conclusion, the root canals shaped at apical foramen exhibited increased filling volume of the main canal in the apical region. However, neither of both working lengths influenced filling of the apical ramifications.

Resumo O presente estudo teve como objetivo comparar o volume preenchido por guta-percha e cimento na região apical do canal principal e ramificações, após instrumentação em dois comprimentos de trabalho diferentes, por meio de nano tomografia computadorizada (nano-TC). Vinte e dois pré-molares com ramificações apicais foram selecionados após avaliação por micro-tomografia computadorizada e foram divididos aleatoriamente em grupos para posterior instrumentação endodôntica em dois comprimentos de trabalho diferentes: G1 - Canais radiculares instrumentados 1 mm aquém do forame apical (n = 11) e G2 - Canais radiculares instrumentados até o forame apical (n = 11). Após a obturação dos canais radiculares, imagens de nano-CT foram adquiridas, e o volume preenchido por guta-percha e cimento nas faixas apicais de 0-4 mm e 0-1 mm do canal principal, e ramificações apicais, foram avaliadas objetivamente por um especialista em radiologia e endodontia, cego para ambos os grupos. O teste de Mann-Whitney foi aplicado para comparar os dois grupos quanto ao preenchimento das faixas apicais do canal principal e ramificações com nível de significância de 5% (α ≤ 0,05). Observou-se que canais radiculares instrumentados até o forame apical apresentaram maior volume do canal principal preenchido do que canais radiculares instrumentados 1 mm aquém do forame apical, em ambas as faixas apicais (0-4 e 0-1 mm) (p <0,05) Em relação ao preenchimento das ramificações apicais, não houve diferença significativa entre os grupos (p> 0,05). Em conclusão, os canais radiculares instrumentados até o forame apical mostraram um maior volume de preenchimento na região apical do canal principal. No entanto, os dois diferentes comprimentos de trabalho não influenciaram o preenchimento das ramificações apicais.

Detection of Incomplete Root Fractures in Endodontically Treated Teeth Using Different High-resolution Cone-beam Computed Tomographic Imaging Protocols.

INTRODUCTION: The purpose of this study was to compare different high-resolution cone-beam computed tomographic (CBCT) imaging protocols in the diagnosis of incomplete root fractures of endodontically treated teeth. METHODS: Twenty single-rooted human teeth were endodontically treated, and an incomplete root fracture was induced. The teeth were scanned with the CBCT unit PreXion 3D (Teracom, San Mateo, CA) operating at 2 different protocols: high resolution/standard (HI-STD) (19 seconds and 512 basis images) and high resolution/high density (HI-HI) (37 seconds and 1024 basis images). Three oral radiologists evaluated all images using multiplanar reconstructions. The diagnostic tests and the receiver operating characteristic (ROC) curve were calculated. RESULTS: The HI-STD and HI-HI protocols presented an accuracy of 0.90 and 0.93, respectively, and both protocols had a sensitivity of 0.97. The HI-HI protocol showed a higher positive predictive value and slightly higher areas under the ROC curve. CONCLUSIONS: Both high-resolution imaging protocols presented high accuracy in the detection of incomplete root fracture of endodontically teeth. Thus, the HI-STD protocol should be indicated this reduces the radiation dose.