A Novel Method for Obtaining Analytical Parameters Based on Double-Flank Measurement.

Double-flank measurement is the most commonly used method for full inspection of mass-produced gears and has high measurement efficiency, but it cannot obtain the analytical parameters and is not helpful enough to evaluate the NVH performance of the gears. Based on the double-flank rolling tester with a new principle, a simulation method for double-flank measurement and a solving method for analytical parameters are proposed. Using the simulation method, the double-flank measurements without random error can be obtained through the collision detection algorithm. The solving method uses the iteration to obtain the minimum rolling length of each position of the tooth surface, then obtains the analytical parameters of the gear. In the experiments, the difference between the profile deviations obtained by the solving method and superimposed in the simulation method is less than 0.03 µm. The experiment results have verified the correctness of the simulation method and the solving method. These methods can greatly improve the value of double-flank measurement.

Temporomandibular disorder patients with excessive daytime sleepiness present greater pain intensity and reduced jaw function.

BACKGROUND: Sleep disorders are associated with temporomandibular disorders (TMDs). Limited studies have focused on excessive daytime sleepiness (EDS) and its impact on jaw functions in TMD patients. OBJECTIVE: The aim of the present investigation was to identify the impact of EDS on pain and jaw function in TMD patients. METHODS: A total of 338 TMD patients (50 males and 288 females) was included. The Epworth Sleepiness Scale (ESS) was used to classify patients into EDS group (score ≥ 10) and non-EDS group (score < 10). The Jaw Functional Limitation Scale 8-item (JFLS-8) was used to assess the severity of jaw dysfunction. Pain intensity was evaluated using the Visual Analogue Scale (VAS). Anxiety and depression were evaluated using the Generalised Anxiety Disorder 7-item (GAD-7) and the Patient Health Questionnaire 9-item (PHQ-9). All included patients were diagnosed with pain-related TMD (PT), intra-articular TMD (IT) or combined TMD (CT). RESULTS: Compared with non-EDS patients, EDS patients exhibited more severe jaw dysfunction, greater pain intensity and higher PHQ-9 scores (p < .05). Multivariate analyses showed that EDS (B = 3.69), female gender (B = 3.69), and elevated GAD-7 score (B = 0.73) were significantly associated with an increased score on the JFLS-8 (p < .05). Moreover, bivariate logistic regression analysis indicated a significant relationship between EDS and PT (OR = 2.70, p = .007). CONCLUSION: The presence of EDS was more closely related to PT, but the causal relationship between them needs to be further confirmed. More concern and intervention to alleviate poor sleep quality might be highlighted during the treatment of TMD, especially PT subtype.

Characterizing enterovirus C96 genome and phylodynamics analysis.

Enterovirus C96 (EV-C96) is a recently discovered serotype belonging to enterovirus C species. It had been isolated from patients with acute flaccid paralysis, hand, foot, and mouth disease, diarrhea, healthy people, or environmental specimens. Despite increasing reports of the virus, the small number of full-length genomes available for EV-C96 has limited molecular epidemiological studies. In this study, newly collected rare EV-C96 strains in China from 1997 to 2020 were combined with sequences available in GenBank for comprehensive analyses. Sequence analysis revealed that the nucleotide sequence similarity of EV-C96 and the prototype strain (BAN00-10488) was 75%-81.8% and the amino acid sequence similarity was 85%-94.9%. EV-C96 had a high degree of genetic variation and could be divided into 15 genogroups. The mean evolutionary rate was 5.16 × 10-3 substitution/site/year, and the most recent common ancestor was dated to 1925. A recombination analysis revealed that EV-C96 may be a recombinant derived from other serotypes in the EV-C group in the nonstructural protein coding region. This comprehensive and integrated analysis of the whole genome sequence of EV-C96 provides valuable data for further studies on the molecular epidemiology of EV-C96 worldwide.

Study on the Measurability of Gear Analytical Parameters in Double-Flank Measurement.

Double-flank measurement is the most commonly used full inspection method on the shop floor. However, the double-flank measurement method cannot measure analytical parameters such as pitch deviations and profile deviations, and this limitation is a pain point in the field of gear measurement. This paper studies the measurability of the analytical parameters of gears based on the results of double-flank measurement, proposes the definition of measurable area, and gives the relationship between the size of the measurable area and the number of teeth and the pressure angle and the gear error. Digital simulation methods were used to conduct measurement experiments on gear analytical parameters. In the experiments, the measurability of the analytical parameters of gears with various typical profile deviations in the double-flank measurement process was verified and analyzed. The test results show that not all profile deviations are unmeasurable in the process of double-flank measurement, but there exists a profile region in which the analytical parameters of the gear can be measured accurately. The size of the measurable area of the profile is mainly determined by the number of teeth and pressure angle of the gear, while the pitch deviations are always measurable under normal conditions.

Critical review on quality of methodology and recommendations of clinical practice guidelines for peri-implantitis.

BACKGROUND: Peri-implantitis is of high prevalence with the popularity of dental implants nowadays. Guidelines or consensus have been developed in succession, and we are little-known about their quality. The objective of this study is to evaluate the methodological quality of these guidelines and analyze the consistency of the clinical recommendations. METHODS: We searched for guidelines or consensus on prevention, diagnosis, and/or treatment of peri-implantitis through PubMed, Web of Science, Cochrane Library until January 15th, 2022. In addition, we also searched the websites of the American Dental Association, International Team for Implantology, FDI World Dental Federation, and some guideline collection databases. Appraisal of Guidelines for Research & Evaluation II methodological quality instrument was used to assess the selected guidelines. Furthermore, we described the consistency of recommendations across the included guidelines. RESULTS: In total, 15 guidelines were included. The mean values of the six domains score all below 50%. The mean scores of Applicability were lowest (mean:15%, range:4-29%). As to the overall quality, eleven (73%) were recommended after being modified, and four (27%) were not recommended. Among the clinical recommendations, 53 (67.09%) are for treatment of peri-implantitis, 13 (16.46%) for monitoring issue, 7 (8.86%) for diagnosis, 3 (3.80%) for the disease prevention. CONCLUSIONS: Improving methodology quality and strengthening clinical evidence is essential in the future guideline development in a range of disciplines for improving the treatment effectiveness of people with peri-implantitis. And there is a lack of integrated guidelines in the case of the COVID-19 pandemic.

Synchronous Reconstruction of the Jaw Using a "One and a Half"-Barrel Fibular Bone Graft for Ossifying Fibroma Patients.

BACKGROUND: Ossifying fibroma is one of the common benign tumors that affect the appearance and functions of the jaw. Ossifying fibroma may exhibit a wide range of biological behaviors, leading to deformities involving the jaw and other secondary facial deformities. Hence, to improve the function of the jaw and the patient's general facial appearance (bearing in mind each patient's facial shape and, or appearance), the authors thus, however, used a ''one and a half"-barrel fibular bone graft to achieve the ideal height and radian of the bone graft. CASE PRESENTATION: Between July 2017 and January 2021, the authors retrospectively collected and analyzed clinical and surgical data from 39 patients who had undergone operations in our hospital. Twenty patients were operated on using our new surgical method, whereas 19 patients received conventional or debulking operation. Clinical factors associated with the operation were assessed, including classification of the jaw defects, perioperative complications, and postoperative outcomes. RESULTS: All the flaps ultimately survived. According to the postoperative satisfaction survey, patients who underwent reconstruction were satisfied with their postoperative facial appearance, with an average of 8.5 out of 10. Based on the preoperative clinical data, 26 patients had suitable bone grafts for dentures to improve their oral function. CONCLUSIONS: A ''one and a half''-barrel fibular bone graft effectively improves the facial appearance of patients and as well as provides an appropriate height and radian for the bone graft.

Monomethyl Auristatin E Grafted-Liposomes to Target Prostate Tumor Cell Lines.

Novel nanomedicines have been engineered to deliver molecules with therapeutic potentials, overcoming drawbacks such as poor solubility, toxicity or short half-life. Lipid-based carriers such as liposomes represent one of the most advanced classes of drug delivery systems. A Monomethyl Auristatin E (MMAE) warhead was grafted on a lipid derivative and integrated in fusogenic liposomes, following the model of antibody drug conjugates. By modulating the liposome composition, we designed a set of particles characterized by different membrane fluidities as a key parameter to obtain selective uptake from fibroblast or prostate tumor cells. Only the fluid liposomes made of palmitoyl-oleoyl-phosphatidylcholine and dioleoyl-phosphatidylethanolamine, integrating the MMAE-lipid derivative, showed an effect on prostate tumor PC-3 and LNCaP cell viability. On the other hand, they exhibited negligible effects on the fibroblast NIH-3T3 cells, which only interacted with rigid liposomes. Therefore, fluid liposomes grafted with MMAE represent an interesting example of drug carriers, as they can be easily engineered to promote liposome fusion with the target membrane and ensure drug selectivity.

Factors Influencing the Immunogenicity and Immunotoxicity of Cyclic RGD Peptide-Modified Nanodrug Delivery Systems.

c(RGDyK)-modified liposomes have been shown to be immunogenic and potentially trigger acute systemic anaphylaxis upon repeated intravenous injection in both BALB/c nude mice and ICR mice. However, questions concerning the potential influence of mouse strains, immunization routes, drug carrier properties, and changes in c(RGDyK) itself on the immunogenicity and resultant immunotoxicity (anaphylaxis) of cyclic RGD peptide-modified nanodrug delivery systems remain unanswered. Here, these potential impact factors were investigated, aiming to better understand the immunological properties of cyclic RGD peptide-based nanodrug delivery systems and seek for solutions for this immunogenicity-associated issue. It was revealed that anaphylaxis caused by intravenous c(RGDyK)-modified drug delivery systems might be avoided by altering the preimmunization route (i.e., subcutaneous injection), introducing positively charged lipids into the liposomes and by using micelles or red blood cell membrane (RBC)-based drug delivery systems as the carrier. Different murine models showed different incidences of anaphylaxis following intravenous c(RGDyK)-liposome stimulation: anaphylaxis was not observed in both SD rats and BALB/c mice and was less frequent in C57BL/6 mice than that in ICR mice. In addition, enlarging the peptide ring of c(RGDyK) by introducing amino sequence serine-glycine-serine reduced the incidence of anaphylaxis post the repeated intravenous c(RGDyKSGS)-liposome stimulation. However, immunogenicity of cyclic RGD-modified drug carriers could not be reversed, although some reduction in IgG antibody production was observed when ICR mice were intravenously stimulated with c(RGDyK)-modified micelles, RBC membrane-based drug delivery systems and c(RGDyKSGS)-liposomes instead of c(RGDyK)-liposomes. This study provides a valuable reference for future application of cyclic RGD peptide-modified drug delivery systems.

Treatment of Lung Cancer by Peptide-Modified Liposomal Irinotecan Endowed with Tumor Penetration and NF-κB Inhibitory Activities.

Current chemotherapy for lung cancer achieved limited efficacy due to poor tumor targeting and tissue penetration. Another obstacle in the therapy is activated nuclear factor-κB (NF-κB) in tumor cells, which plays a crucial role in promotion of antiapoptosis and drug resistance. In this study, we utilized a multifunctional liposome loaded with irinotecan and surface modified with a cell-permeable NF-κB inhibitor (CB5005), for treatment of non-small-cell lung carcinoma. CB5005 downregulated the level of NF-κB-related protein in the nuclei of A549 cells, and increased cellular uptake of the modified liposomes. In vivo antitumor activity in mice bearing A549 xenografts revealed that modification with CB5005 significantly improved the tumor inhibition rate of irinotecan. Immunohistochemical assays showed that the tumors treated with CB5005-modified liposomes possessed the most apoptotic cells and the lowest level of p50 in the cell nuclei. These results strongly suggest that antitumor efficacy of the irinotecan liposomes can be enhanced by tumor-penetrating and NF-κB-inhibiting functions of CB5005. Consequently, CB5005-modified liposomes provide a possible synergistic therapy for lung cancer, and would also be appropriate for other types of tumors associated with elevated NF-κB activity.

Elective Neck Dissection Versus Observation in Squamous Cell Carcinoma of Oral Cavity With Clinically N0 Neck: A Systematic Review and Meta-Analysis of Prospective Studies.

PURPOSE: To assess the possible benefits of elective neck dissection (END) in patients with squamous cell carcinoma (SCC) of the oral cavity and clinically N0 neck. MATERIALS AND METHODS: Medline, Embase, the China National Knowledge Infrastructure, and the Wan Fang Database were systematically searched. A meta-analysis was performed to evaluate the possible benefits of END to such patients. RESULTS: Six prospective studies involving 865 patients fulfilled the inclusion criteria. Meta-analysis of all included studies showed that END substantially lowered the risk of regional recurrences (risk ratio [RR] = 0.27; 95% confidence interval [CI], 0.21-0.36) in the fixed-effect model compared with observation only. Three of the 6 included studies showed that the specific death rate related to regional recurrences was lower in the END group than in the observation group in the fixed-effect model (RR = 0.35; 95% CI, 0.19-0.65). The mean metastasis rate of occult cervical lymph node was 30.27% (standard deviation, 9.42%). When the fixed-effect model was applied, 4 of the 6 included studies showed less recurrence in the END group compared with the observation group (RR = 0.53; 95% CI, 0.44-0.64). CONCLUSIONS: END substantially decreases recurrences and deaths related to regional recurrences in early-stage SCC of the oral cavity with clinically N0 neck, especially SCC of the oral tongue and floor of the mouth, which is necessary for such patients.

The predictive value of polysomnography combined with quality of life for treatment decision of children with habitual snoring related to adenotonsillar hypertrophy.

PURPOSE: Both surgical treatment and non-surgical treatment are suggested by clinicians for children with habitual snoring related to adenotonsillar hypertrophy; However, how should the decision be made remains unclear. The objective of this study was to investigate potential predictors for the treatment decision, i.e., surgical treatment vs wait and see in children with habitual snoring related to adenoidal and/or tonsillar hypertrophy. METHODS: Children with complaints of snoring and/or apnea associated with adenotonsillar hypertrophy who received polysomnography (PSG) monitoring at our Hospital were recruited. After at least 6 months, the subjects were followed up and grouped according to whether or not they had received adenoidectomy and/or tonsillectomy (AT) execution. The heights, weights, as well as the quality of life (assessed using the obstructive sleep apnea-18 (OSA-18) quality of life questionnaire) and baseline PSG of the subjects were recorded and compared. Two logistic regressions were performed to reveal the factors influencing decision-making on conducting AT. RESULTS: A total of 509 children were finally included (345 males and 164 females). Among these children, 287 eventually received AT. Significant differences in age, scores for item 1 and 5 of the OSA-18, apnea-hypopnea index, obstructive apnea index, obstructive apnea-hypopnea index (OAHI), and Lowest arterial oxygen saturation (P < 0.05) were observed between groups. By multivariate logistic regression, the factors that influenced the surgical decision were identified as follows: age < 7 years (P = 0.008: odds ratio [OR] = 1.667, 95% confidence interval [CI] 1.140-2.438), score for item 5 of OSA-18 > 4 points (P = 0.042: OR = 1.489, 95% CI 1.014-2.212) and OAHI > 1/h (P = 0.044: OR = 1.579, 95% CI 1.013-2.463). CONCLUSION: School-age children aged < 7 years, with OAHI > 1/h and mouth breathing scored > 4 points were more likely to receive AT during the disease process and thus require increased attention.

Application of Intraoperative Navigation for the Reconstruction of Mandibular Defects With Microvascular Fibular Flaps-Preliminary Clinical Experiences.

BACKGROUND: A microvascular fibular flap is the main option for the reconstruction of mandibular defects. This paper introduces an innovative strategy for the accurate fabrication of fibular flaps. METHODS: Nine patients with mandibular tumors were included in this study. The mandibular reconstruction planning was performed using MIMICS 10.01. One reconstruction plate was preformed. During the operation, the fibular flap was fabricated and implanted using the BrainLab navigation system. Six to 12 months after surgery, computed tomography data were acquired and compared with preoperative planning. RESULTS: The osteotomy of the fibular flap and the mandible was easily performed, using the navigation and the osteotomy template respectively. The preformed plate accurately determined the position of the flap. The treatment outcome was consistent with the preoperative planning using 3D analysis. CONCLUSIONS: Combination of the intraoperative navigation and preformed plate technique demonstrated great practical value in mandibular reconstruction with microvascular fibular flaps.

The improvement of pain symptoms in patients with burning mouth syndrome through combined laser and medication therapy.

BACKGROUND: The etiology of Burning Mouth Syndrome (BMS) remains unclear. OBJECTIVE: To explore the differences in the therapeutic efficacy of pain improvement between medication therapy and laser therapy in patients with BMS. METHODS: 45 BMS patients were randomly divided into three groups: The Combination therapy group (Group A, n= 15), The Medication therapy group (Group B, n= 15), and the Laser therapy group (Group C, n= 15). The pain condition of the patients was evaluated using the Numeric Rating Scale (NRS), and the improvement in pain before and after treatment was compared among the three groups. RESULTS: All three groups (A, B, and C) showed a significant reduction in NRS scores after treatment, with statistically significant differences observed among the different groups. Group A exhibited the most significant improvement, with a statistically significant difference before and after treatment. CONCLUSION: Laser and medication therapy are effective methods for reducing oral burning pain * symptoms, and their combined use yields more significant therapeutic effects.

The improvement of pain symptoms in patients with burning mouth syndrome through combined laser and medication therapy.

BACKGROUND: The etiology of Burning Mouth Syndrome (BMS) remains unclear. OBJECTIVE: To explore the differences in the therapeutic efficacy of pain improvement between medication therapy and laser therapy in patients with BMS. METHODS: 45 BMS patients were randomly divided into three groups: The Combination therapy group (Group A, n= 15), The Medication therapy group (Group B, n= 15), and the Laser therapy group (Group C, n= 15). The pain condition of the patients was evaluated using the Numeric Rating Scale (NRS), and the improvement in pain before and after treatment was compared among the three groups. RESULTS: All three groups (A, B, and C) showed a significant reduction in NRS scores after treatment, with statistically significant differences observed among the different groups. Group A exhibited the most significant improvement, with a statistically significant difference before and after treatment. CONCLUSION: Laser and medication therapy are effective methods for reducing oral burning pain * symptoms, and their combined use yields more significant therapeutic effects.

Changes in microbial composition explain the contrasting responses of glucose and lignin decomposition to soil acidification in an alpine grassland.

Soil acidification often suppresses microbial growth and activities, resulting in a negative impact on soil organic carbon (C) decomposition. While the detrimental effects of acidification on soil and plant properties have been extensively studied, less attention has been paid on the shifts in soil microbial communities and their influences of the decomposition of organic C with different chemical complexities. Taking advantage of an acid addition experiment in a Tibetan alpine meadow, here we examined the response of soil microbial communities to soil acidification and microbial effect on the decomposition of organic C with different chemical complexities (i.e., glucose and lignin, representing labile and recalcitrant C respectively). We found that soil acidification had no impact on microbial respiration and microbial abundance even though it decreased bacterial diversity significantly. Soil acidification increased the relative abundance of some microbial taxa, like Alphaproteobacteria and Acidobacteriia in bacteria increased by 36 %, 284 %, and Eurotiomycetes, Sordariomycetes and Leotiomycetes in fungi increased by 145 %, 279 % and 12.7-fold, but decreased the relative abundance of Acidimicrobiia by 33 % in highest acid addition treatment. Changes in microbial communities (bacterial and fungal community composition, the diversity of bacterial community and the ratio of fungi to bacteria) are significantly related to the decomposition of glucose and lignin. More specifically, soil acidification decreased the decomposition of glucose but increased the decomposition of lignin, indicating a trade-off between the decomposition of labile and recalcitrant soil organic C under soil acidification. Overall, shifts in microbial communities under soil acidification might be accompanied by an increased ability to break down more recalcitrant C. This trade-off between the decomposition of labile and recalcitrant C may change soil C quality under future acid deposition scenarios.

Fiber configuration determines foreign body response of electrospun scaffolds:in vitroandin vivoassessments.

Biomaterial scaffolds boost tissue repair and regeneration by providing physical support, delivering biological signals and/or cells, and recruiting endogenous cells to facilitate tissue-material integration and remodeling. Foreign body response (FBR), an innate immune response that occurs immediately after biomaterial implantation, is a critical factor in determining the biological outcomes of biomaterial scaffolds. Electrospinning is of great simplicity and cost-effectiveness to produce nanofiber scaffolds with well-defined physicochemical properties and has been used in a variety of regenerative medicine applications in preclinical trials and clinical practice. A deep understanding of causal factors between material properties and FBR of host tissues is beneficial to the optimal design of electrospun scaffolds with favorable immunomodulatory properties. We herein prepared and characterized three electrospun scaffolds with distinct fiber configurations and investigated their effects on FBR in terms of immune cell-material interactions and host responses. Our results show that electrospun yarn scaffold results in greater cellular immune reactions and elevated FBR inin vivoassessments. Although the yarn scaffold showed aligned fiber bundles, it failed to induce cell elongation of macrophages due to its rough surface and porous grooves between yarns. In contrast, the aligned scaffold showed reduced FBR compared to the yarn scaffold, indicating a smooth surface is also a contributor to the immunomodulatory effects of the aligned scaffold. Our study suggests that balanced porousness and smooth surface of aligned fibers or yarns should be the key design parameters of electrospun scaffolds to modulate host responsein vivo.

Evaluation of a newly developed oral and maxillofacial surgical robotic platform (KD-SR-01) in head and neck surgery: a preclinical trial in porcine models.

Traditional open head and neck surgery often leaves permanent scars, significantly affecting appearance. The emergence of surgical robots has introduced a new era for minimally invasive surgery. However, the complex anatomy of the head and neck region, particularly the oral and maxillofacial areas, combined with the high costs associated with established systems such as the da Vinci, has limited the widespread adoption of surgical robots in this field. Recently, surgical robotic platform in China has developed rapidly, exemplified by the promise shown by the KangDuo Surgical Robot (KD-SR). Although the KD-SR has achieved some results comparable to the da Vinci surgical robot in urology and colorectal surgery, its performance in complex head and neck regions remains untested. This study evaluated the feasibility, effectiveness, and safety of the newly developed KD-SR-01, comparing it with standard endoscopic systems in head and neck procedures on porcine models. We performed parotidectomy, submandibular gland resection, and neck dissection, collected baseline characteristics, perioperative data, and specifically assessed cognitive workload using the NASA-TLX. None of the robotic procedures were converted to endoscopic or open surgery. The results showed no significant difference in operation time between the two groups (P = 0.126), better intraoperative bleeding control (P = 0.001), and a significant reduction in cognitive workload (P < 0.001) in the robotic group. In conclusion, the KD-SR-01 is feasible, effective, and safe for head and neck surgery. Further investigation through well-designed clinical trials with long-term follow-up is necessary to establish the full potential of this emerging robotic platform.

Genotype F of Echovirus 25 with multiple recombination pattern have been persistently and extensively circulating in Chinese mainland.

Echovirus 25 (E25), a member of the Enterovirus B (EV-B) species, can cause aseptic meningitis (AM), viral meningitis (VM), and acute flaccid paralysis (AFP). However, systematic studies on the molecular epidemiology of E25, especially those concerning its evolution and recombination, are lacking. In this study, 18 strains of E25, isolated from seven provinces of China between 2009 and 2018, were collected based on the Chinese hand, foot, and mouth disease (HFMD) surveillance network, and 95 sequences downloaded from GenBank were also screened. Based on the phylogenetic analysis of 113 full-length VP1 sequences worldwide, globally occurring E25 strains were classified into 9 genotypes (A-I), and genotype F was the dominant genotype in the Chinese mainland. The average nucleotide substitution rate of E25 was 6.08 × 10-3 substitutions/site/year, and six important transmission routes were identified worldwide. Seventeen recombination patterns were determined, of which genotype F can be divided into 9 recombination patterns. A positive selector site was found in the capsid protein region of genotype F. Recombination analysis and pressure selection analysis for genotype F showed multiple recombination patterns and evolution characteristics, which may be responsible for it being the dominant genotype in the Chinese mainland. This study provides a theoretical basis for the subsequent prevention and control of E25.

Reverse engineering of Perseris and development of compositionally equivalent formulations.

Six injectable, long-acting in situ forming implant drug products based on poly(lactide-co-glycolide) (PLGA) and N-Methyl-2-Pyrrolidone (NMP) are available on the market. However, generic products, which would likely be more affordable for patients, are not yet available. This is partially due to the unique complexity of these formulations as well as the inherent heterogeneity of PLGA and the challenges in the manufacture and characterization of this polymer. This article focuses on a comprehensive characterization of Perseris (risperidone) in situ forming implant drug product, and the development of compositionally equivalent formulations. The molecular weight (MW), lactide/glycolide (L/G) ratio, end group, blockiness and glass transition temperature (Tg) of PLGA, as well as the crystal form and particle size of risperidone powder used in Perseris were identified through reverse engineering. The dissolved/suspended drug ratio in the final implant suspension for administration, as well as the real-time drug solid state in the solidified Perseris drug depot were investigated. Two compositionally equivalent formulations prepared using customized PLGA polymers with similar properties to the Perseris PLGA showed similar in vitro release and swelling behavior to Perseris as demonstrated using a novel adapter-based dissolution method. The novelty of this dissolution method lies in its ability to control implant shape, generate reproducible data, distinguish different release phases, as well as identify formulation changes. The knowledge gained in this work and the methodology established for characterization of the implant formulations are important for implant formulation development.

Oxidation of cellulose molecules toward delignified oxidated hot-pressed wood with improved mechanical properties.

Wooden building materials have advantages in terms of biodegradability, non-toxicity, pollution-free and recycling. Currently, applications of natural wood are extremely limited because of low density, low strength and toughness. Therefore, we reported an effective modification strategy with nano-scale cellulose nanofibrils design to prepare a synergistically enhanced cellulosic material. Via three steps: i) the secondary alcohol hydroxyl groups in C2, C3 position were cut; ii) oxidize the hydroxyl group at C2, C3 position to achieve dialdehyde cellulose; and iii) oxidized again to obtain dicarboxylic cellulose. Subsequently, thanks to the regulation of the average moisture content, the moisture content in the wood surface and subsurface increased in a short time. The wood softening layer contributes to the hotpressing treatment of the wood. The mechanical properties and dimensionality have been greatly improved. The obtained delignified oxidated hot-pressed wood with 0.55 mmol/g carboxyl group content demonstrates excellent strength of 328.8 ± 7.43 MPa and Young's modulus of 8.1 ± 0.14 GPa, which is twice than that of natural wood. Delignified oxidated hot-pressed wood also shows exceptional toughness of 8.3 ± 0.28 MJ/m3. Other than that, the shore hardness indicates 0.55 mmol/g carboxylic group, which could increase the hardness at the wood surface hardness to 72.5 ± 4.29°.