Microtensile bond strength of one- and two-step self-etching adhesives on sclerotic dentin: the effects of thermocycling.

This study evaluated the effects of thermocycling on the microtensile bond strength (microTBS) of one- and two-step self-etch adhesives (SEAs) to sclerotic dentin. Two adhesives, Clearfil S3 Bond (S3), a one-step self-etch adhesive (1-SEA), and Clearfil SE Bond (SE), a two-step self-etch adhesive (2-SEA), were applied on cervical lesions in human premolars with sclerotic or normal dentin. After adhesive application, the lesions were restored and built up using a resin composite (Clearfil AP-X). After 24 hours in water storage, the restored teeth were sectioned into 0.7 x 0.7 mm composite-dentin beams. The beams were then aged with 0, 5,000 or 10,000 thermocycles. The use of two adhesives, two substrate types and three thermocycling regimens yielded 12 experimental groups of 14-19 beams each. The beams were subsequently subjected to microTBS testing at a crosshead speed of 1 mm/minute and statistical analyses were computed with three-way ANOVA and Tukey's post hoc test at p < 0.05. Three-way ANOVA showed statistically significant effects on bonding effectiveness by lesion type, adhesive system, thermocycling or combinations of the adhesive system and thermocycling (p < 0.05). With sclerotic dentin, although S3 and SE provided comparable microTBS after 24 hours of water storage, S3 showed significantly lower microTBS than SE after thermocycling (p < 0.05). Regardless of lesion type, the microTBS for S3 decreased significantly after 5,000 or 10,000 thermocycles, while the microTBS for SE showed a significant decrease only after 10,000 thermocycles. Regardless of the extent of thermocycling, the microTBS values for either SE or S3 bonded to sclerotic dentin were significantly lower than to normal dentin (p < 0.05). The results suggested that thermocycling had a significant negative effect on the bond strength of the two SEAs tested. In contrast to 2-SEA, 1-SEA might not be a good choice for sclerotic dentin when seeking durability of the resin-dentin bond.

Effects of insulin-like growth factor I on the development of osteoblasts in hyperglycemia.

The delayed wound healing of tooth extraction, the activation of alveolar absorption and the being hindered bone formation around the implants in diabetes are difficult to be solved for dentists. So, the aim of the study was to investigate the influences of hyperglycemia and insulin-like growth factor I (IGF-I) on osteoblasts. Osteoblasts were cultured in different conditions: normal glucose, mimic hyperglycemia, hyperglycemia with IGF-I, hyperglycemia with insulin. The proliferation and mineralization of osteoblasts were observed. As abnormal transport of glucose involved in the development of chronic complications in diabetes. The expression of glucose transporter 1 (GLUT1) was further evaluated by RT-PCR, immunofluorescence and Western blot in different groups. These results showed that hyperglycemia increased the proliferation and inhibited the mineralization of osteoblasts, while IGF-I seemed to reverse these effects. The levels of GLUT1 mRNA and protein in hyperglycemia were elevated by 51% and 35%, respectively, compared with that in normal glucose, while the levels in hyperglycemia with IGF-I were almost the same as that in normal glucose. In conclusion, the increased expression of GLUT1 may contribute to the delayed mineralization of osteoblasts in hyperglycemia. Also IGF-I may be a new drug for diabetic bone disease through normalizing the expression of GLUT1.

Three-dimensional finite element analysis of weakened roots restored with different cements in combination with titanium alloy posts.

BACKGROUND: It is very difficult and relatively unpredictable to preserve and restore severely weakened pulpless roots. To provide much needed benefit basis for clinical practice, this study was carried out to analyze the stress distribution in weakened roots restored with different cements in combination with titanium alloy posts. Finite element analysis (FEA) was employed in the study. METHODS: A pseudo three-dimensional model of a maxillary central incisor with flared root canal, theoretically restored with titanium alloy posts in combination with different cements, was established. The analysis was performed by use of ANSYS software. The tooth was assumed to be isotropic, homogenous and elastic. A load of 100 N at an angle of 45 degrees to the longitudinal axis was applied at the palatal surface of the crown. The distributions of stresses in weakened roots filled with cements of different elastic modulus were analyzed by the three-dimensional FEA model. RESULTS: Several stress trends were observed when the stress cloud atlas obtained in the study was analyzed. With the increase of the elastic modulus of cements from 1.8 GPa to 22.4 GPa, the stress values in dentin decreased from 39.58 MPa to 31.43 MPa and from 24.51 MPa to 20.76 MPa (respectively, for maximum principle stress values and Von Mises stress values). When Panavia F and zinc phosphate cement were used, the stress peak values in dentin were very small with no significant difference observed, and the Von Mises stress values were 20.87 MPa and 20.76 MPa respectively. On the other hand, maximum principle stress value and Von Mises stress value in cement layer increased with the increase of the elastic modulus of cements. CONCLUSIONS: The result of this study demonstrated that elastic modulus was indeed one of the important parameters to evaluate property of the cements. Our three-dimensional FEA model study also found that the cement with elastic modulus similar to that of dentin could reinforce weakened root and reduce the stress in dentin. Thus, it may be a better choice for the restoration of weakened roots in clinical practice.

Biomechanical optimisation of the length ratio of the two endosseous portions in distraction implants: a three-dimensional finite element analysis.

Insufficient alveolar height is one of the most common problems in oral implantation, and it may preclude placement of an implant or compromise the final aesthetic outcome of the restoration. To solve this problem, distraction implants (DIs) have been introduced because they can fulfill the functions of bony augmentation and implantation simultaneously and facilitate the operation, minimise the trauma, and shorten the duration of treatment. However, the high risk of complications such as device fracture from uneven distribution of stress or transport bone resorption from insufficient blood supply, has impeded their clinical use. As the cortical transport portion of the DI is more important for bearing occlusal force than the apical support portion, and the length of the transport portion is normally the height of the transport bone segment, lengthening the transport portion may help to obtain a rational distribution of stress and increase the blood supply to the transport bone. For those cases in which alveolar height is limited, the dimension of the DI must be minimised to be applicable, so it is important to find an optimised balance between the lengths of the transport and support portions for a better performance. We have made a finite element analysis to optimise the length ratio of transport:support portions. The effects of the length ratios on the stress distribution in the jawbones were evaluated. A ratio of 8:2 showed the minimum stress and most resistance to displacement. These results provide a valuable reference for further improvement of designs of DI and help to promote its clinical application.

[Effect of sandblasting particle sizes on bonding strength between porcelain and titanium fabricated by rapid laser forming].

OBJECTIVE: To evaluate the effect of sandblasting particle sizes of Al2O3 on the bonding strength between porcelain and titanium fabricated by laser rapid forming (LRF). METHODS: The thermal expansion coefficient, roughness (Ra), contact angle, surface morphology of titanium surface and the bonding strength between titanium and porcelain were evaluated after the titanium surface being sandblasted using different sizes of Al2O3 (50 microm, 120 microm, 250 microm) at a pressure of 0.5 MPa. The cast titanium specimens were used as control, and were sandblasted with 50 microm Al2O3 at the same pressure. RESULTS: The thermal expansion coefficient of cast titanium [(9.84 +/- 0.42) x 10(-6)/ degrees C] and LRF Ti [(9.79 +/- 0.31) x 10(-6)/ degrees C) matched that of Noritake Ti-22 dentin porcelain [(8.93 +/- 0.36) x 10(-6)/ degrees C). When larger size of Al2O3 was used, the value of Ra and contact angle increased as well. There was no significant difference in bonding strength between the LRF Ti-50 microm [(25.91 +/- 1.02) MPa] and cast titanium [(26.42 +/- 1.65) MPa]. Significantly lower bonding strength was found in LRF Ti-120 microm [(21.86 +/- 1.64) MPa] and LRF Ti-250 microm [(19.96 +/- 1.03) MPa]. CONCLUSIONS: The bond strength between LRF Ti and Noritake Ti-22 dentin porcelain was above the lower limit value in the ISO 9693 (25 MPa) after using 50 microm Al2O3 sandblasting in 0.5MPa air pressure.

[An 8-year follow-up study of Cerec2 computer aided design and computer aided manufacture of all-ceramic crowns].

OBJECTIVE: To evaluate the clinical performance of the crowns made by Cerec2 computer aided design and computer aided manufacture (CAD/CAM) system. METHODS: Twenty four teeth were restored with Cerec2 CAD/CAM crowns. Eight years after delivery of the prostheses, the all-ceramic crowns were evaluated using modified standard of California Dental Association quality evaluation system. Patients filled out a satisfaction questionnaire at the same time. And Kaplan-Meier analysis was carried out. RESULTS: Three out of 24 restorations were rated as failure. Kaplan-Meier analysis showed that the success rate of Cerec2 crowns eight year following delivery was 88%. CONCLUSIONS: Crowns made by Cerec2 CAD/CAM system can survive in oral condition and function well for 8 years.

[Structural characteristics of laser-welded cast pure titanium joints by different gap distance].

OBJECTIVE: To measure the microstructure of laser-welded cast pure titanium by different gap distance. METHODS: Forty specimens were sectioned and welded at four gaps (0.00 mm, 0.25 mm, 0.50 mm and 1.00 mm). Took microhardness test and metallographic examination of welded zone surface. RESULTS: There were no difference in microhardness value and metallographic observation between welded specimens. The width of heat-effected zone was different. The smaller grains and needle-like alphamartensitic structure were found in the heat-affected zone. CONCLUSION: The effects of the joint gap were not significant.

[Effects of laser welding on bond of porcelain fused cast pure titanium].

OBJECTIVE: To investigate the influence of the laser welding on bond of porcelain fused to cast pure titanium. METHODS: Twenty cast titanium plates were divided into two groups: laser welded group and control group. The low-fusing porcelain was fused to the laser welded cast pure titanium plates at fusion zone. The bond strength of the porcelain to laser welded cast pure titanium was measured by the three-point bending test. The interface of titanium and porcelain was investigated by scanning electron microscopy (SEM) and energy depressive X-ray detector (EDX). The non-welded titanium plates were used as comparison. RESULTS: No significant difference of the bond strength was found between laser-welded samples [(46.85 +/- 0.76) MPa] and the controls [(41.71 +/- 0.55) MPa] (P > 0.05). The SEM displayed the interface presented similar irregularities with a predominance. The titanium diffused to low-fusing porcelain, while silicon and aluminum diffused to titanium basement. CONCLUSIONS: Laser welding does not affect low-fusing porcelain fused to pure titanium.

[The study on fabrication of dental restoration using PMMA-ZrO2 composites via CAD/CAM].

OBJECTIVE: To obtain dental restorations by machining PMMA-ZrO2 organic-inorganic composites with the dental CAD/CAM system. METHODS: Partially sintered Zirconia compacts (PSZC) were prepared via isostatic pressing and partially sintering, with Zirconia nanopowder as raw materials. PMMA-Zirconia organic-inorganic composites were prepared by vacuum infiltrating the prepolymerized MMA into the PSZC, followed by in-situ polymerization. The mechanical properties and machinability of composites were studied. The composites were machined on the dental CAD/CAM system to obtain dental restoration. RESULTS: At 71.44% TD of PSZC, the composite had a 3-point bending strength of (202.56 +/- 3.09) MPa, fracture toughness of (4.30 +/- 0.16) MPa.m(1/2), elasticity modulus of (58.71 +/- 1.98) GPa, and Vickers hardness of (3.82 +/- 0.34) GPa, respectively. A premolar crown was fabricated by CAD/CAM system in 16 mins, and was verisimilitude, without any cracks. CONCLUSIONS: The composite at 71.44% TD of PSZC has good mechanical properties and dental restorations can be manufactured by PMMA-Zirconia composites via dental CAD/CAM system.

[Influence of eugenol-containing temporary cement on efficacy of dentin-bonding systems].

OBJECTIVE: This study investigated the influence of eugenol-containing temporary cement on the efficacy of two relatively new dentin-bonding systems. METHODS: Thirty-two freshly extracted bovine central incisors were randomly divided into four groups. Dentin was exposed and polished with 320#, 400#, and 600# sand papers. After embedded, Group 3 and 4 specimens were covered with ZOE. Specimens in Group 1 and 2 were served as control. All specimens were stored for 1 week in distilled water at 37 degrees C. Then, the ZOE was mechanically removed. The dentin surfaces of Group 1 and 3 were treated with Prime & Bond NT bonding system and the dentin surfaces of Group 2 and 4 were treated with GLUMA adhesive system according to manufacturer's instructions. Thereafter composite resin columns (6 mm diameter, 2 mm high) were applied. After specimens stored in distilled water at 37 degrees C for 24 hours, the shear bond testing was carried out using a SHIMADZU universal testing machine with a cross-head speed of 0.5 mm/minute. The mode of failure was examined using SEM. The data were analyzed using ANOVA test at a significance level of 0.05. RESULTS: The medians of shear bond strength for each group were as follows: Group 1 (Prime & Bond NT) 9.57 MPa, Group 3 (Prime & Bond NT + ZOE) 10.72 MPa, Group 2 (GLUMA) 16.89 MPa, Group 4 (GLUMA + ZOE) 16.78 MPa. Group 1 and 3 had significantly lower bonding strength than did Groups 2 and 4. But no significant difference was found between the control groups and the groups treated with ZOE temporary cement. CONCLUSION: Pretreatment of the dentin with ZOE temporary cement has no adverse influence on the efficacy of two relatively new dentin-bonding systems.

[Coloration of mica glass ceramic for use in dental CAD/CAM system].

OBJECTIVE: An intrinsically colored machinable glass-ceramic containing tetrasilicic fluormica as the predominant crystal phase was studied, which was used in molar crown in dental CAD/CAM system. METHODS: Orthogonal design analysis was used to select appropriate base formula, coloration and heat treatment process. RESULTS: Factors influencing the color appearance of mica glass ceramic were nucleation agent and the ratio of Mg(2+) to K(+) in base formula; Cerium oxide (CeO(2)) was used as the main coloration; The preferred heat treatment was 650 degrees C for 1 h and 1,000 degrees C or 1,050 degrees C for 3 h - 4 h. CONCLUSIONS: This mica glass-ceramic could provide 4 to 5 color appearance for dental use, it showed excellent machinability which was eminently suitable for use in dental CAD/CAM system.

[Experimental study of periosteal osteoblasts adhesion to artificial bone scaffolds based on rapid prototype].

OBJECTIVE: To study the biocompatibility of bone engineering scaffolds designed and fabricated by CAD and Rapid Prototyping techniques. METHODS: Infant rat calvarias osteoblasts were isolated and expanded in vitro and the cells (2nd passage) were seeded onto scaffolds with porosity 80%, 90%, 95% at a density of 2.06 x 10(9)/L. Cell adhesion number and morphology were measured with SEM after 4 days, 10 days co-culture. RESULTS: (1) The osteoblasts' adhesion amounts increased with culture time in three porosity group (P < 0.05), but the increase were different among three groups, 80% group was 0.35 x 10(5), 90% group was 2.84 x 10(5); (2) Through SEM observations, it showed that osteoblasts adhered to all scaffolds well. CONCLUSION: The scaffolds designed and fabricated by CAD and rapid prototyping own a good cellular biocompatibility. The results suggest the feasibility of using such scaffold fabricating method for bone tissue engineering research and clinical therapy.