Modification of pore-wall in direct ink writing wollastonite scaffolds favorable for tuning biodegradation and mechanical stability and enhancing osteogenic capability.

Surface chemistry and mechanical stability determine the osteogenic capability of bone implants. The development of high-strength bioactive scaffolds for in-situ repair of large bone defects is challenging because of the lack of satisfying biomaterials. In this study, highly bioactive Ca-silicate (CSi) bioceramic scaffolds were fabricated by additive manufacturing and then modified for pore-wall reinforcement. Pure CSi scaffolds were fabricated using a direct ink writing technique, and the pore-wall was modified with 0%, 6%, or 10% Mg-doped CSi slurry (CSi, CSi-Mg6, or CSi-Mg10) through electrostatic interaction. Modified CSi@CSi-Mg6 and CSi@CSi-Mg10 scaffolds with over 60% porosity demonstrated an appreciable compressive strength beyond 20 MPa, which was ~2-fold higher than that of pure CSi scaffolds. CSi-Mg6 and CSi-Mg10 coating layers were specifically favorable for retarding bio-dissolution and mechanical decay of scaffolds in vitro. In-vivo investigation of critical-size femoral bone defects repair revealed that CSi@CSi-Mg6 and CSi@CSi-Mg10 scaffolds displayed limited biodegradation, accelerated new bone ingrowth (4-12 weeks), and elicited a suitable mechanical response. In contrast, CSi scaffolds exhibited fast biodegradation and retarded new bone regeneration after 8 weeks. Thus, tailoring of the chemical composition of pore-wall struts of CSi scaffolds is beneficial for enhancing the biomechanical properties and bone repair efficacy.

Preparation and In Vitro Biological Evaluation of Octacalcium Phosphate/Bioactive Glass-Chitosan/ Alginate Composite Membranes Potential for Bone Guided Regeneration.

The chitosan/alginate-trace element-codoped octacalcium phosphate/nano-sized bioactive glass (CS/ALG-teOCP/nBG) composite membranes were prepared by a layer-by-layer coating method for the functional requirement of guided bone regeneration (GBR). The morphology, mechanical properties and moisture content of the membranes was studied by scanning electron microscopy (SEM) observation, mechanical and swelling test. The results showed that the teOCP/nBG distributed uniformly in the composite membranes, and such as-prepared composite membrane exhibited an excellent tensile strength, accompanying with mechanical decay with immersion in aqueous medium. Cell culture and MTT assays showed that the surface microstructure and the ion dissolution products from teOCP/nBG components could enhance the cell proliferation, and especially the composite membranes was suitable for supporting the adhesion and growth behavior of human bone marrow mesenchymal stem cells (hBMSCs) in comparison with the CS/ALG pure polymer membranes. These results suggest that the new CS/ALG-teOCP/nBG composite membrane is highly bioactive and biodegradable, and favorable for guiding bone regeneration.

The treatment of osteoporotic thoracolumbar severe burst fractures with short pedicle screw fixation and vertebroplasty.

BACKGROUND: To investigate the clinical and radiological results of short pedicle screw fixation and vertebroplasty in osteoporotic thoracolumbar severe burst fractures. METHODS: From September 2006 to August 2010, 19 consecutive patients sustained osteoporotic thoracolumbar severe burst fractures with or without neurologic deficit and were included in this prospective study. All patients underwent short pedicle screw fixation and vertebroplasty. Segmental kyphosis, AVBHr and PVBHr, and Canal compromise were calculated on radiographs pre-operatively, post-operative and at final follow up. VAS, ODI and SF-36 were calculated pre-operatively and at final follow up. RESULTS: Mean operative time was 70.8 min (range 60~100 min) and mean blood loss was 92 ml (range 60~160 ml). The mean duration of their hospital stay was 4.5 days (range 3-7 days). The operative incisions were healing well. Average follow up time was 40.1 months (range 24~72 months). The AVBHr was corrected from preoperative (48.1 ± 6.8) % to postoperative (94.1 ± 1.7) % (P < 0.001). The PVBHr was corrected from preoperative (62.7 ± 4.8) % to postoperative (92.8 ± 1.8) % (P < 0.001). Canal compromise was corrected from preoperative (37.3 ± 5.8) % to postoperative (5.9 ± 2.3) % (P < 0.001). The segmental kyphosis was corrected from preoperative (20.6 ± 5.3) degree to postoperative (2.0 ± 3.2) degree (P < 0.001). VAS scores were reduced from preoperative 7.21 ± 0.86 to 2.21 ± 0.98 at final follow up (P < 0.001). SF-36 Bodily pain was reduced from preoperative 75.31 ± 13.85 to 13.74 ± 13.24 at final follow up (P < 0.001), and SF-36 Role Physical was reduced from preoperative 59.21 ± 26.63 to 19.74 ± 22.94 at final follow up (P < 0.001). The ODI scores were reduced from preoperative 81.68 ± 4.44 to 15.37 ± 5.54 at final follow up (P < 0.001). All 4 patients with partial neurological deficit initially had improvement. Cement leakage was observed in 3 cases (two anterior to vertebral body and one into the disc without sequela). There were no instances of instrumentation failure and no patient had persistent postoperative back pain. CONCLUSIONS: Vertebroplasty and short pedicle screw fixation has the advantages of both radiographic and functional results for treating osteoporotic thoracolumbar severe burst fractures using a purely posterior approach.

Preferentially Biodegradable Gypsum Fibers Endowing Invisible Microporous Structures and Enhancing Osteogenic Capability of Calcium Phosphate Cements.

It is known that hydroxyapatite-type calcium phosphate cement (CPC) shows appreciable self-curing properties, but the phase transformation products often lead to slow biodegradation and disappointing osteogenic responses. Herein, we developed an innovative strategy to endow invisible micropore networks, which could tune the microstructures and biodegradation of α-tricalcium phosphate (α-TCP)-based CPC by gypsum fibers, and the osteogenic capability of the composite cements could be enhanced in vivo. The gypsum fibers were prepared via extruding the gypsum powder/carboxylated chitosan (CC) slurry through a 22G nozzle (410 µm in diameter) and collecting with a calcium salt solution. Then, the CPCs were prepared by mixing the α-TCP powder with gypsum fibers (0-24 wt %) and an aqueous solution to form self-curing cements. The physicochemical characterizations showed that injectability was decreased with an increase in the fiber contents. The µCT reconstruction demonstrated that the gypsum fiber could be distributed in the CPC substrate and produce long-range micropore architectures. In particular, incorporation of gypsum fibers would tune the ion release, produce tunnel-like pore networks in vitro, and promote new bone tissue regeneration in rabbit femoral bone defects in vivo. Appropriate gypsum fibers (16 and 24 wt %) could enhance bone defect repair and cement biodegradation. These results demonstrate that the highly biodegradable cement fibers could mediate the microstructures of conventional CPC biomaterials, and such a bicomponent composite strategy may be beneficial for expanding clinical CPC-based applications.

Core-shell bioceramic fiber-derived biphasic granules with adjustable core compositions for tuning bone regeneration efficacy.

Silicate-based biomaterials-clinically applied fillers and promising candidates-can act as a highly biocompatible substrate for osteostimulative osteogenic cell growth in vitro and in vivo. These biomaterials have been proven to exhibit a variety of conventional morphologies in bone repair, including scaffolds, granules, coatings and cement pastes. Herein, we aim to develop a series of novel bioceramic fiber-derived granules with core-shell structures which have a hardystonite (HT) shell layer and changeable core components-that is, the chemical compositions of a core layer can be tuned to include a wide range of silicate candidates (e.g., wollastonite (CSi)) with doping of functional ions (e.g., Mg, P, and Sr). Meanwhile, it is versatile to control the biodegradation and bioactive ion release sufficiently for stimulating new bone growth after implantation. Our method employs rapidly gelling ultralong core-shell CSi@HT fibers derived from different polymer hydrosol-loaded inorganic powder slurries through the coaxially aligned bilayer nozzles, followed by cutting and sintering treatments. It was demonstrated that the nonstoichiometric CSi core component could contribute to faster bio-dissolution and biologically active ion release in tris buffer in vitro. The rabbit femoral bone defect repair experiments in vivo indicated that core-shell bioceramic granules with an 8% P-doped CSi-core could significantly stimulate osteogenic potential favorable for bone repair. It is worth concluding that such a tunable component distribution strategy in fiber-type bioceramic implants may develop new-generation composite biomaterials endowed with time-dependent biodegradation and high osteostimulative activities for a range of bone repair applications in situ.

[Change in Granulation Potential and Microbial Enrichment Characteristics of Sludge Induced by Microplastics].

Microplastics (MPs), as a new type of pollutant, are widely detected in sewage treatment plants. Currently, research on MPs in traditional sewage treatment systems has mainly been focused on the pollution level and distribution characteristics, with a lack of studying the impact of MPs on the sludge granulation. In order to explore the effect of MPs on the granulation process, a microplastic exposure test was conducted by adding polyethylene terephthalate microplastics (PET-MPs), which are widespread in the environment. The operating performance of the system, extracellular polymeric substance (EPS) composition, and flora enrichment were analyzed on the sludge granulation. The results showed that the exposure of PET-MPs significantly accelerated the sludge granulation process, whereas the increase in EPS content dominated by PN enhanced the sludge surface hydrophobicity; the granulation rate and EPS secretion were proportional to the exposed particle size. Microplastics and EPS secretions synergistically promoted the formation of granular sludge. However, continuous microplastic exposure led to deterioration of the system decontamination performance and inhibited the degradation process of pollutants, with the most negative effect of nitrite nitrogen accumulation under 250 µm PET-MPs exposure, as high as (5.08±0.24) mg·L-1. The high-throughput sequencing revealed that the microbial community diversity fell in the experimental group. The dominant bacteria at the phylum level were Proteobacteria and Bacteroidota on the sludge granulation. Rhodocyclaceae, Sphingomonadaceae, Flavobacteriaceae, and Rhodanobacteraceae promoted flocculation by increasing EPS secretion. The decrease in Comamonadaceae and Chitinophagaceae weakened the ammonia and nitrite oxidation capacity of the system, whereas the decrease in Rhodobacteraceae, Hyphomonadaceae, and Xanthomonadaceae inhibited the removal of nitrate nitrogen.

Artificial osteochondral interface of bioactive fibrous membranes mediating calcified cartilage reconstruction.

Calcified cartilage is a mineralized osteochondral interface region between the hyaline cartilage and subchondral bone. There are few reported artificial biomaterials that could offer bioactivities for substantial reconstruction of calcified cartilage. Herein we developed new poly(L-lactide-co-caprolactone) (PLCL)-based trilayered fibrous membranes as a functional interface for calcified cartilage reconstruction and superficial cartilage restoration. The trilayered membranes were prepared by the electrospinning technique, and the fibrous morphology was maintained when the chondroitin sulfate (CS) or bioactive glass (BG) particles were introduced in the upper or bottom layer, respectively. Although 30% BG in the bottom layer led to a significant decrease in tensile resistance, the inorganic ion release was remarkably higher than that in the counterpart with 10% BG. The in vivo studies showed that the fibrous membranes as osteochondral interfaces exhibited different biological performances on superficial cartilage restoration and calcified cartilage reconstruction. All of the implanted host hyaline cartilage enabled a self-healing process and an increase in the BG content in the membranes was desirable for promoting the repair of the calcified cartilage with time. The histological staining confirmed the osteochondral interface in the 30% BG bottom membrane maintained appreciable calcified cartilage repair after 12 weeks. These findings demonstrated that such an integrated artificial osteochondral interface containing appropriate bioactive ions are potentially applicable for osteochondral interface tissue engineering.

Three-dimensional (3D) printed scaffold and material selection for bone repair.

Critical-sized bone defect repair remains a substantial challenge in clinical settings and requires bone grafts or bone substitute materials. However, existing biomaterials often do not meet the clinical requirements of structural support, osteoinductive property, and controllable biodegradability. To treat large-scale bone defects, the development of three-dimensional (3D) porous scaffolds has received considerable focus within bone engineering. A variety of biomaterials and manufacturing methods, including 3D printing, have emerged to fabricate patient-specific bioactive scaffolds that possess controlled micro-architectures for bridging bone defects in complex configurations. During the last decade, with the development of the 3D printing industry, a large number of tissue-engineered scaffolds have been created for preclinical and clinical applications using novel materials and innovative technologies. Thus, this review provides a brief overview of current progress in existing biomaterials and tissue engineering scaffolds prepared by 3D printing technologies, with an emphasis on the material selection, scaffold design optimization, and their preclinical and clinical applications in the repair of critical-sized bone defects. Furthermore, it will elaborate on the current limitations and potential future prospects of 3D printing technology. STATEMENT OF SIGNIFICANCE: 3D printing has emerged as a critical fabrication process for bone engineering due to its ability to control bulk geometry and internal structure of tissue scaffolds. The advancement of bioprinting methods and compatible ink materials for bone engineering have been a major focus to develop optimal 3D scaffolds for bone defect repair. Achieving a successful balance of cellular function, cellular viability, and mechanical integrity under load-bearing conditions is critical. Hybridization of natural and synthetic polymer-based materials is a promising approach to create novel tissue engineered scaffolds that combines the advantages of both materials and meets various requirements, including biological activity, mechanical strength, easy fabrication and controllable degradation. 3D printing is linked to the future of bone grafts to create on-demand patient-specific scaffolds.

Unveiling the mechanisms of how cationic polyacrylamide affects short-chain fatty acids accumulation during long-term anaerobic fermentation of waste activated sludge.

Cationic polyacrylamide, a flocculation powder widely used in wastewater pretreatment and sludge dewatering, was highly accumulated in waste activated sludge. However, its effect on short-chain fatty acids (SCFAs) accumulation from anaerobic fermentation of waste activated sludge has not been investigated. This work therefore aims to deeply unveil how cationic polyacrylamide affects SCFAs production, through both long-term and batch tests using either real waste activated sludge or synthetic wastewaters as fermentation substrates. Experimental results showed that the presence of cationic polyacrylamide not only significantly decreased the accumulation of SCFAs but also affected the composition of individual SCFA. The concentration of SCFAs decreased from 3374.7 to 2391.7 mg COD/L with cationic polyacrylamide level increasing from 0 to 12 g/kg of total suspended solids, whereas the corresponding percentage of acetic acid increased from 45.2% to 55.5%. The mechanism studies revealed that although cationic polyacrylamide could be partially degraded to produce SCFAs during anaerobic fermentation, cationic polyacrylamide and its major degradation metabolite, polyacrylic acid, inhibited all the sludge solubilization, hydrolysis, acidogenesis, acetogenesis and homoacetogenesis processes to some extents. As a result, the accumulation of SCFAs in the cationic polyacrylamide added systems decreased rather than increased. However, the inhibition to acetogenesis and homoacetogenesis was slighter than that to acidogenesis, leading to an increase of acetic acid to total SCFAs. It was further found that cationic polyacrylamide had stronger ability to adhere to protein molecules surface, which inhibited the bioconversion of proteins more severely. Illumina MiSeq sequencing analyses showed that cationic polyacrylamide decreased microbial community diversity, altered community structure and changed activities of key enzymes responsible for SCFAs accumulation.

Core-Shell Biphasic Microspheres with Tunable Density of Shell Micropores Providing Tailorable Bone Regeneration.

IMPACT STATEMENT: We have developed the new core-shell bioceramic CSi-Sr4@CaP-px microspheres with tuning porous shell layer so that the biodegradation of both CSi-Sr4 core and CaP shell is readily adjusted synergistically. This is for the first time, to the best of our knowledge, that the bioceramic scaffolds concerning gradient distribution and microstructure-tailoring design is available for tailoring biodegradation and ion release (bioactivity) to optimizing osteogenesis. Furthermore, it is possibly helpful to develop new bioactive scaffold system for time-dependent tailoring bioactivity and microporous structure to significantly enhance bone regeneration and repair applications, especially in some non-load-bearing arbitrary 3D anatomical bone and teeth defects.

Microwave pretreatment of polyacrylamide flocculated waste activated sludge: Effect on anaerobic digestion and polyacrylamide degradation.

Deterioration of anaerobic digestion can occur with the presence of polyacrylamide (PAM) in waste activated sludge, but the information on alleviating this deterioration is still limited. In this study, the simultaneous alleviation of negative effect of PAM and improvement of methane production during anaerobic digestion was accomplished by microwave pretreatment. Experimental results showed that with the microwave pretreatment times increased from 0 to 12 min, the biochemical methane potential of PAM-flocculated sludge (12 g PAM/kg total solids) asymptotically increased from 123.1 to 242.5 mL/g volatile solids, hydrolysis rate increased from 0.06 to 0.13 d-1. Mechanism analysis indicated that the microwave pretreatment accelerated the release and hydrolysis of organic substrates from PAM-flocculated sludge, facilitated the breaking of large firm "PAM-sludge" floccules, and benefited the degradation of PAM, which alleviated the PAM inhibitory impacts on digestion and meanwhile provided better contact between the released organic substrates and anaerobic bacteria for methane production.

Nonstoichiometric wollastonite bioceramic scaffolds with core-shell pore struts and adjustable mechanical and biodegradable properties.

Controllable mechanical strength and biodegradation of bioceramic scaffolds is a great challenge to treat the load-bearing bone defects. Herein a new strategy has been developed to fabricate porous bioceramic scaffolds with adjustable component distributions based on varying the core-shell-structured nozzles in three-dimensional (3D) direct ink writing platform. The porous bioceramic scaffolds composed of different nonstoichiometic calcium silicate (nCSi) with 0%, 4% or 10% of magnesium-substituting-calcium ratio (CSi, CSi-Mg4, CSi-Mg10) was fabricated. Beyond the mechanically mixed composite scaffolds, varying the different nCSi slurries through the coaxially aligned bilayer nozzle makes it easy to create core-shell bilayer bioceramic filaments and better control of the different nCSi distribution in pore strut after sintering. It was evident that the magnesium substitution in CSi contributed to the increase of compressive strength for the single-phasic scaffolds from 11.2 MPa (CSi), to 39.4 MPa (CSi-Mg4) and 80 MPa (CSi-Mg10). The nCSi distribution in pore struts in the series of core-shell-strut scaffolds could significantly adjust the strength [e.g. CSi@CSi-Mg10 (58.9 MPa) vs CSi-Mg10@CSi (30.4 MPa)] and biodegradation ratio in Tris buffer for a long time stage (6 weeks). These findings demonstrate that the nCSi components with different distributions in core or shell layer of pore struts lead to tunable strength and biodegradation inside their interconnected macropore architectures of the scaffolds. It is possibly helpful to develop new bioactive scaffolds for time-dependent tailoring mechanical and biological performances to significantly enhance bone regeneration and repair applications, especially in some load-bearing bone defects.

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect.

Three-dimensional (3D) printing bioactive ceramics have demonstrated alternative approaches to bone tissue repair, but an optimized materials system for improving the recruitment of host osteogenic cells into the bone defect and enhancing targeted repair of the thin-wall craniomaxillofacial defects remains elusive. Herein we systematically evaluated the role of side-wall pore architecture in the direct-ink-writing bioceramic scaffolds on mechanical properties and osteogenic capacity in rabbit calvarial defects. The pure calcium silicate (CSi) and dilute Mg-doped CSi (CSi-Mg6) scaffolds with different layer thickness and macropore sizes were prepared by varying the layer deposition mode from single-layer printing (SLP) to double-layer printing (DLP) and then by undergoing one-, or two-step sintering. It was found that the dilute Mg doping and/or two-step sintering schedule was especially beneficial for improving the compressive strength (∼25-104 MPa) and flexural strength (∼6-18 MPa) of the Ca-silicate scaffolds. The histological analysis for the calvarial bone specimens in vivo revealed that the SLP scaffolds had a high osteoconduction at the early stage (4 weeks) but the DLP scaffolds displayed a higher osteogenic capacity for a long time stage (8-12 weeks). Although the DLP CSi scaffolds displayed somewhat higher osteogenic capacity at 8 and 12 weeks, the DLP CSi-Mg6 scaffolds with excellent fracture resistance also showed appreciable new bone tissue ingrowth. These findings demonstrate that the side-wall pore architecture in 3D printed bioceramic scaffolds is required to optimize for bone repair in calvarial bone defects, and especially the Mg doping wollastontie is promising for 3D printing thin-wall porous scaffolds for craniomaxillofacial bone defect treatment.

Systematic evaluation of the osteogenic capacity of low-melting bioactive glass-reinforced 45S5 Bioglass porous scaffolds in rabbit femoral defects.

Due to the low strength and high brittleness of 45S5 Bioglass®, it is still a great challenge for the three-dimensional porous 45S5 Bioglass® to treat mechanically required loaded bone defects. Therefore, 45S5 Bioglass®-derived bioactive glass-ceramic (BGC) porous scaffolds were fabricated at a low temperature sintering condition with and without the addition of 4% low-melting ZnO/B2O3 (ZB) bioactive glass as a reinforcing agent and using 350- or 500 µm paraffin microspheres as a porogen. The pore structure characterization for the scaffolds indicated that the scaffolds containing 4% ZB had very good macroporous structures of ∼313 and ∼448 µm in pore size and over 70% porosity with appreciable strength (>15 MPa), which was about four times higher than that those manufactured without ZB and with 350 µm porogen scaffolds. The open porosity was decreased with the addition of 4% ZB but the interconnected pore percentage (>50 µm) was increased with increasing the porogen size from 350 to 500 µm. In vivo investigations revealed that the stronger scaffolds containing 4% ZB and 500 µm porogen were particularly beneficial for osteogenic capacity in critical size femoral bone defects, accompanied with an accelerated bone ingrowth (6-18 weeks) and the material itself experiencing mild resorption. In contrast, both the scaffolds with smaller pore sizes exhibited a low level of new bone ingrowth (<32%) after 6-12 weeks implantation. These results suggest a promising application of such 45S5 Bioglass®-derived BGC scaffolds in a clinical setting, especially for mechanically loaded bone defects.

Systematic comparison of biologically active foreign ions-codoped calcium phosphate microparticles on osteogenic differentiation in rat osteoporotic and normal mesenchymal stem cells.

Osteoporosis is a disease characterized by structural deterioration of bone tissue, leading to skeletal fragility with increased fracture risk. Calcium phosphates (CaPs) are widely used in bone tissue engineering strategies as they have similarities to bone apatite except for the absence of trace elements (TEs) in the CaPs. Bioactive glasses (BGs) have also been used successfully in clinic for craniomaxillofacial and dental applications during the last two decades due to their excellent potential for bonding with bone and inducing osteoblastic differentiation. In this study, we evaluated the osteogenic effects of the ionic dissolution products of the quaternary Si-Sr-Zn-Mg-codoped CaP (TEs-CaP) or 45S5 Bioglass® (45S5 BG), both as mixtures and separately, on rat bone marrow-derived mesenchymal stem cells (rOMSCs & rMSCs) from osteoporotic and normal animals, using an MTT test and Alizarin Red S staining. The materials enhanced cell proliferation and osteogenic differentiation, especially the combination of the BG and TEs-CaP. Analysis by quantitative PCR and ELISA indicated that the expression of osteogenic-specific genes and proteins were elevated. These investigations suggest that the TEs-CaP and 45S5 BG operate synergistically to create an extracellular environment that promotes proliferation and terminal osteogenic differentiation of both osteoporotic and normal rMSCs.

Cross-linked versus conventional polyethylene for total knee arthroplasty: a meta-analysis.

BACKGROUND: Highly cross-linked polyethylene (HXLPE) has been reported as an effective material for decreasing polyethylene wear and osteolysis in total knee arthroplasty (TKA). Because no single study to date has been large enough to definitively determine the benefit of HXLPE in TKA, we conducted a meta-analysis to pool the results from randomized controlled trials (RCTs) and non-RCTs to make such a determination. METHODS: Potential candidate articles were identified by searching the Cochrane Library, Medline (1966-2015.10), PubMed (1966-2015.10), Embase (1980-2015.10), ScienceDirect (1985-2015.10), and other databases. "Gray studies" were identified from the included articles' reference lists. Pooled data were analyzed using RevMan 5.1. RESULTS: Three RCTs and three non-RCTs were included in the meta-analysis. There were no significant differences between the groups in the total number of reoperations (P = 0.11), reoperations for prosthesis loosening (P = 0.08), radiolucent line (P = 0.20), osteolysis (P = 0.38), prosthesis loosening (P = 0.10), and mechanical failures related to the tibial polyethylene (P = 1.00). Similarly, no significant differences between the two groups were found in postoperative total knee score (P = 0.18) or functional score (P = 0.23). CONCLUSIONS: The meta-analysis showed that compared with conventional polyethylene, HXLPE did not improve the clinical and radiographic outcomes in mid-term follow-up after TKA. Additional high-quality multicenter prospective RCTs with good design, large study populations and long-term follow-up will be necessary to further clarify the effect of HXLPE in TKA.

Bioactive glass-reinforced bioceramic ink writing scaffolds: sintering, microstructure and mechanical behavior.

The densification of pore struts in bioceramic scaffolds is important for structure stability and strength reliability. An advantage of ceramic ink writing is the precise control over the microstructure and macroarchitecture. However, the use of organic binder in such ink writing process would heavily affect the densification of ceramic struts and sacrifice the mechanical strength of porous scaffolds after sintering. This study presents a low-melt-point bioactive glass (BG)-assisted sintering strategy to overcome the main limitations of direct ink writing (extrusion-based three-dimensional printing) and to produce high-strength calcium silicate (CSi) bioceramic scaffolds. The 1% BG-added CSi (CSi-BG1) scaffolds with rectangular pore morphology sintered at 1080 °C have a very small BG content, readily induce apatite formation, and show appreciable linear shrinkage (∼21%), which is consistent with the composite scaffolds with less or more BG contents sintered at either the same or a higher temperature. These CSi-BG1 scaffolds also possess a high elastic modulus (∼350 MPa) and appreciable compressive strength (∼48 MPa), and show significant strength enhancement after exposure to simulated body fluid-a performance markedly superior to those of pure CSi scaffolds. Particularly, the honeycomb-pore CSi-BG1 scaffolds show markedly higher compressive strength (∼88 MPa) than the scaffolds with rectangular, parallelogram, and Archimedean chord pore structures. It is suggested that this approach can potentially facilitate the translation of ceramic ink writing and BG-assisted sintering of bioceramic scaffold technologies to the in situ bone repair.

Novel highly bioactive and biodegradable gypsum/calcium silicate composite bone cements: from physicochemical characteristics to in vivo aspects.

Gypsum is a promising material for bone defect repair due to its osteoconductivity, whereas it is still limited in orthopedic and dental surgeries due to its low bioactivity and too rapid resorption so that one major concern is the significant loss in microstructural stability in vivo. In the present strategy some key features were significantly improved by introducing rapidly biodegradable but highly bioactive calcium silicate (CS) for regulating the physicochemical properties and biological performances of the gypsum-based cements at the same liquid/solid ratio. We demonstrated that introduction of 23% CS into ß-calcium sulfate hemihydrate (CSH) could improve the physicochemical properties but would not compromise the mechanical strength of the composite. The surface bioactivity was significantly enhanced by introducing 23% CS, and these biphasic composites were favorable for decelerating the biodegradation rate by nearly 18.5% in 28 days in vitro. A mild bioresorption rate, with 39.6% of composite residual 4 weeks after operation, was determined when implanted in subcutaneous tissue of rats. 8 weeks after implantation, the composite cement containing 23% CS significantly enhanced new bone tissue regeneration with a much higher relative bone content (∼68.6%) than pure gypsum in critical size femoral defects in rabbits. The novel CSH-CS biocements represent promising candidates for rapid bone resconstruction and repair in trauma and pathological conditions.

Preparation and in vitro evaluation of strontium-doped calcium silicate/gypsum bioactive bone cement.

The combination of two or more bioactive components with different biodegradability could cooperatively improve the physicochemical and biological performances of the biomaterials. Here we explore the use of α-calcium sulfate hemihydrate (α-CSH) and calcium silicate with and without strontium doping (Sr-CSi, CSi) to fabricate new bioactive cements with appropriate biodegradability as bone implants. The cements were fabricated by adding different amounts (0-35 wt%) of Sr-CSi (or CSi) into the α-CSH-based pastes at a liquid-to-solid ratio of 0.4. The addition of Sr-CSi into α-CSH cements not only led to a pH rise in the immersion medium, but also changed the surface reactivity of cements, making them more bioactive and therefore promoting apatite mineralization in simulated body fluid (SBF). The impact of additives on long-term in vitro degradation was evaluated by soaking the cements in Tris buffer, SBF, and α-minimal essential medium (α-MEM) for a period of five weeks. An addition of 20% Sr-CSi to α-CSH cement retarded the weight loss of the samples to 36% (in Tris buffer), 43% (in SBF) and 54% (in α-MEM) as compared with the pure α-CSH cement. However, the addition of CSi resulted in a slightly faster degradation in comparison with Sr-CSi in these media. Finally, the in vitro cell-ion dissolution products interaction study using human fetal osteoblast cells demonstrated that the addition of Sr-CSi improved cell viability and proliferation. These results indicate that tailorable bioactivity and biodegradation behavior can be achieved in gypsum cement by adding Sr-CSi, and such biocements will be of benefit for enhancing bone defect repair.

Two-step pH-modulated rapid assembly of trace-element-doped calcium-phosphate nanocrystals into giant porous beads in gelatin hydrosol for biomedical applications.

Biomolecule-ion interactions that occur during changes in pH value are a crucial but poorly investigated area that underlies the aggregation of inorganic nanocrystals. Meanwhile, the disorderly growth of calcium phosphate (CaP) nanocrystals is an obstacle that limits its practical applications. Herein, we have demonstrated for the first time that a simple two-step pH-adjustment process for a gelatin hydrosol reaction medium can modulate the ordered self-assembly of trace-element-doped CaP nanocrystals into porous beads. Two methods are used to adjust the initial pH value of gelatin hydrosol: One is to firstly adjust the pH value to 3.0 and then to 4.0 with acid/base solutions, whilst the other is to directly adjust the pH value to 4.0 with acid. Spherical CaP porous beads are rapidly produced through the two-step pH-adjustment process, whereas the one-step pathway results in disorderly CaP aggregates. We believe that the introduction of additives for pH adjustment is the dominant factor in disturbing the electrokinetic parameters and for driving the self-assembly of nanocrystals, whereas the nucleation of CaP nanocrystals prior to assembly is caused by the relaxation/condensation of the polypeptide network, owing to the increase in pH value on the introduction of the basic calcium salt. This method is facile and rapid and these highly bioactive porous beads are particularly promising for use in hard-tissue repair, tissue engineering, and drug delivery.