Factorial Design Based Multivariate Modeling and Optimization of Tunable Bioresponsive Arginine Grafted Poly(cystaminebis(acrylamide)-diaminohexane) Polymeric Matrix Based Nanocarriers.

Desired characteristics of nanocarriers are crucial to explore its therapeutic potential. This investigation aimed to develop tunable bioresponsive newly synthesized unique arginine grafted poly(cystaminebis(acrylamide)-diaminohexane) [ABP] polymeric matrix based nanocarriers by using L9 Taguchi factorial design, desirability function, and multivariate method. The selected formulation and process parameters were ABP concentration, acetone concentration, the volume ratio of acetone to ABP solution, and drug concentration. The measured nanocarrier characteristics were particle size, polydispersity index, zeta potential, and percentage drug loading. Experimental validation of nanocarrier characteristics computed from initially developed predictive model showed nonsignificant differences (p > 0.05). The multivariate modeling based optimized cationic nanocarrier formulation of <100 nm loaded with hydrophilic acetaminophen was readapted for a hydrophobic etoposide loading without significant changes (p > 0.05) except for improved loading percentage. This is the first study focusing on ABP polymeric matrix based nanocarrier development. Nanocarrier particle size was stable in PBS 7.4 for 48 h. The increase of zeta potential at lower pH 6.4, compared to the physiological pH, showed possible endosomal escape capability. The glutathione triggered release at the physiological conditions indicated the competence of cytosolic targeting delivery of the loaded drug from bioresponsive nanocarriers. In conclusion, this unique systematic approach provides rational evaluation and prediction of a tunable bioresponsive ABP based matrix nanocarrier, which was built on selected limited number of smart experimentation.

An implantable thermoresponsive drug delivery system based on Peltier device.

Locally dropping the temperature in vivo is the main obstacle to the clinical use of a thermoresponsive drug delivery system. In this paper, a Peltier electronic element is incorporated with a thermoresponsive thin film based drug delivery system to form a new drug delivery device which can regulate the release of rhodamine B in a water environment at 37 °C. Various current signals are used to control the temperature of the cold side of the Peltier device and the volume of water on top of the Peltier device affects the change in temperature. The pulsatile on-demand release profile of the model drug is obtained by turning the current signal on and off. The work has shown that the 2600 mAh power source is enough to power this device for 1.3 h. Furthermore, the excessive heat will not cause thermal damage in the body as it will be dissipated by the thermoregulation of the human body. Therefore, this simple novel device can be implanted and should work well in vivo.

A mathematical model for pulsatile release: controlled release of rhodamine B from UV-crosslinked thermoresponsive thin films.

A controlled drug delivery system fabricated from a thermoresponsive polymer was designed to obtain a pulsatile release profile which was triggered by altering the temperature of the dissolution medium. Two stages of release behaviour were found: fast release for a swollen state and slow (yet significant and non-negligible) release for a collapsed state. Six cycles of pulsatile release between 4 °C and 40 °C were obtained. The dosage of drug (rhodamine B) released in these cycles could be controlled to deliver approximately equal doses by altering the release time in the swollen state. However, for the first cycle, the swollen release rate was found to be large, and the release time could not be made short enough to prevent a larger dose than desired being delivered. A model was developed based on Fick's law which describes pulsatile release mathematically for the first time, and diffusion coefficients at different temperatures (including temperatures corresponding to both the fully swollen and collapsed states) were estimated by fitting the experimental data with the theoretical release profile given by this model. The effect of temperature on the diffusion coefficient was studied and it was found that in the range of the lower critical solution temperature (LCST), the diffusion coefficient increased with decreasing temperature. The model predicts that the effective lifetime of the system lies in the approximate range of 1-42 h (95% of drug released), depending on how long the system was kept at low temperature (below the LCST). Therefore this system can be used to obtain a controllable pulsatile release profile for small molecule drugs thereby enabling optimum therapeutic effects.

Straightforward, one-step fabrication of ultrathin thermoresponsive films from commercially available pNIPAm for cell culture and recovery.

The use of thermoresponsive surfaces as platforms for cell culture and cell regeneration has been explored over the last couple of decades. Poly-N-isopropylacrylamide (pNIPAm) is a well characterized thermoresponsive polymer which has an aqueous lower critical solution temperature (LCST) in a physiologically useful range, which allows it to reversibly attract (T < 32 °C) and repel water (T > 32 °C). It is this phenomenon that is exploited in temperature-controlled cell harvesting. pNIPAm coatings are generally poorly cell compatible and a number of complex or expensive techniques have been developed in order to overcome this issue. This study seeks to design a simple one-step system whereby commercially sourced pNIPAm is used to achieve similar results. Films were deposited using the operationally simple but rheologically complex spin coating technique. Reversible temperature modulated cell adhesion was achieved using a variety of different cell lines. This system offers a simplistic and cheaper alternative to methods used elsewhere.