Combined metabolome and transcriptome analysis reveals a critical role of lignin biosynthesis and lignification in stem-like pneumatophore development of the mangrove Avicennia marina.

MAIN CONCLUSION: Transcriptional and metabolic regulation of lignin biosynthesis and lignification plays crucial roles in Avicennia marina pneumatophore development, facilitating its adaptation to coastal habitats. Avicennia marina is a pioneer mangrove species in coastal wetland. To cope with the periodic intertidal flooding and hypoxia environment, this species has developed a complex and extensive root system, with its most unique feature being a pneumatophore with a distinct above- and below-ground morphology and vascular structure. However, the characteristics of pneumatophore lignification remain unknown. Studies comparing the anatomy among above-ground pneumatophore, below-ground pneumatophore, and feeding root have suggested that vascular structure development in the pneumatophore is more like the development of a stem than of a root. Metabolome and transcriptome analysis illustrated that the accumulation of syringyl (S) and guaiacyl (G) units in the pneumatophore plays a critical role in lignification of the stem-like structure. Fourteen differentially accumulated metabolites (DAMs) and 10 differentially expressed genes involved in the lignin biosynthesis pathway were targeted. To identify genes significantly associated with lignification, we analyzed the correlation between 14 genes and 8 metabolites and further built a co-expression network between 10 transcription factors (TFs), including 5 for each of MYB and NAC, and 23 enzyme-coding genes involved in lignin biosynthesis. 4-Coumarate-CoA ligase, shikimate/quinate hydroxycinnamoyl transferase, cinnamyl alcohol dehydrogenase, caffeic acid 3-O-methyltransferase, phenylalanine ammonia-lyase, and peroxidase were identified to be strongly correlated with these TFs. Finally, we examined 9 key candidate genes through quantitative real-time PCR to validate the reliability of transcriptome data. Together, our metabolome and transcriptome findings reveal that lignin biosynthesis and lignification regulate pneumatophore development in the mangrove species A. marina and facilitate its adaptation to coastal habitats.

Review on vat photopolymerization additive manufacturing of bioactive ceramic bone scaffolds.

Bone defects frequently occur in clinical settings due to trauma, disease, tumors, and other causes. The clinical use of autologous bones and allograft bone, however, has several limitations, such as limited sources, donor site morbidity, and immunological rejection. Nevertheless, there is newfound hope for regenerating and repairing bone defects through the development and integration of bone tissue engineering scaffold and additive manufacturing (AM) technology, also known as 3D printing. In particular, vat photopolymerization (VPP)-AM of bioactive ceramic bone scaffolds has garnered significant interest from interdisciplinary researchers in recent years. On the one hand, VPP-AM demonstrates clear advantages in printing accuracy and speed compared to other AM and non-AM technologies. On the other hand, bioactive ceramic materials exhibit superior bioactivity, biodegradability, and mechanical properties compared to metals, polymers, and bioinert ceramics, making them one of the most promising biomaterials for developing bone scaffolds. This paper reviews the research progress of VPP-AM of bioactive ceramic bone scaffolds, covering the process principles of various VPP-AM technologies, the performance requirements and preparation process of VPP ceramic slurry, the VPP process of bioactive ceramic bone scaffolds, and the research progress on different material types of VPP bioactive ceramic scaffolds. Firstly, we provide a brief introduction to the process principles and medical applications of various VPP technologies. Secondly, we explore the composition of the VPP ceramic slurry system, discussing the function of various components and their effects on printing quality. Thirdly, we delve into the performance requirements of bone scaffolds and summarize the research progress of VPP bioactive ceramic bone scaffolds of various material types including hydroxyapatite (HA), tricalcium phosphate (TCP), bioglass (BG), etc.; Finally, we discuss the challenges currently faced by VPP-AM bioactive ceramic bone scaffolds and propose possible development directions for the future.

3D printed TPMS structural PLA/GO scaffold: Process parameter optimization, porous structure, mechanical and biological properties.

Bone scaffolds should have good biocompatibility and mechanical and biological properties, which are primarily by the material design, porous structure, and preparation process. In this study, we proposed polylactic acid (PLA) as the base material, graphene oxide (GO) as an enhancing filler, triply periodic minimal surface (TPMS) as a porous structure, and fused deposition modeling (FDM) 3D printing as a preparation technology to develop a TPMS structural PLA/GO scaffold and evaluate their porous structures, mechanical properties, and biological properties towards bone tissue engineering. Firstly, the influence of the FDM 3D printing process parameters on the forming quality and mechanical properties of PLA was studied by orthogonal experimental design, based on which the process parameters were optimized. Then, GO was composited with PLA, and PLA/GO nanocomposites were prepared by FDM. The mechanical tests showed that GO can effectively improve the tensile and compression strength of PLA; only by adding 0.1% GO the tensile and compression modulus was increased by 35.6% and 35.8%, respectively. Then, TPMS structural (Schwarz-P, Gyroid) scaffold models were designed and TPMS structural PLA/0.1%GO nanocomposite scaffolds were prepared by FDM. The compression test showed that the TPMS structural scaffolds had higher compression strength than the Grid structure; This was owing to the fact that the continuous curved structure of TMPS alleviated stress concentration and had a more uniform stress bearing. Moreover, cell culture indicated bone marrow stromal cells (BMSCs) showed better adhesion, proliferation, and osteogenic differentiation behaviors on the TPMS structural scaffolds as the continuous surface structure of TPMS had better connectivity and larger specific surface area. These results suggest that the TPMS structural PLA/GO scaffold has potential application in bone repair. This article suggests the feasibility of co-designing the material, structure, and technology for achieving the good comprehensive performance of polymer bone scaffolds.

A natural biomineral for enhancing the biomineralization and cell response of 3D printed polylactic acid bone scaffolds.

Polylactic acid (PLA) has been extensively used as a bone scaffold material, but it still faces many problems including low biomineralization ability, weak cell response, low mechanical properties, etc. In this study, we proposed to utilize the distinctive physical, chemical and biological properties of a natural biomineral with organic matrix, pearl powder, to enhance the overall performance of PLA bone scaffolds. Porous PLA/pearl composite bone scaffolds were prepared using fused deposition modeling (FDM) 3D printing technology, and their comprehensive performance was investigated. Macro- and micro- morphological observation by the optical camera and scanning electron microscopy (SEM) showed the 3D printed scaffolds have interconnected and ordered periodic porous structures. Phase analysis by X-ray diffraction (XRD) indicated pearl powder was well composited with PLA without impurity formation during the melt extrusion process. The mechanical test results indicated the tensile and compressive strength of PLA/pearl composite scaffolds with 10 % pearl powder content yielded the highest values, which were 15.5 % and 21.8% greater than pure PLA, respectively. The water contact angle and water absorption tests indicated that PLA/pearl showed better hydrophilicity than PLA due to the presence of polar groups in the organic matrix of the pearl powder. The results of the simulated body fluid (SBF) soaking revealed that the addition of pearl powder effectively enhanced the formation and deposition of apatite, which was attributed to the release of Ca2+ from the dissolution of pearl powder. The cell culture of bone marrow mesenchymal stem cells (BMSCs) indicated that PLA/pearl scaffolds showed better cell proliferation and osteogenic differentiation than PLA due to the stimulation of the biological organic matrix in pearl powder. These outcomes signify the potential of pearl powder as a natural biomineral containing bio-signal factors to improve the mechanical and biological properties of polymers for better bone tissue engineering application.

Substrate-free, ultra-conformable PEDOT: PSS E-tattoo achieved by energy regulation on skin.

Electronic tattoo has great potential application in mobile health. Fully conformal contact between E-tattoo and skin is critical for reliable monitoring. In this paper, we reported a substrate-free, ultra-conformable PEDOT: PSS (3,4-ethylenedioxythiophene):poly(styrene-sulfonate) E-tattoo achieved by interface energy regulation on skin. The controllable gel/dry electrode mutual transformation property of PEDOT: PSS was carefully studied and reported. Then a novel transfer approach was studied to transfer thin, substrate-free PEDOT: PSS E-tattoo onto skin. Meanwhile, PEDOT: PSS E-tattoo was gelled, then dried directly on skin, regulating its bending energy, contact area, and interface adhesion energy with skin. Through this method, the critical thickness of the after-transformation dry E-tattoo that could form fully conformal contact with skin was increased by 4 times. The electrode-skin interface impedance and ECG measurement performance of the reported E-tattoo were on par with commercial Ag/AgCl gel electrodes, while offering superior comfort and reliability. The substrate-free, ultra-conformable PEDOT: PSS E-tattoo could be applied as sensing electrode for reliable monitoring in mobile health.