Porphyrin/phthalocyanine-based porous organic polymers for pollutant removal and detection: Synthesis, mechanisms, and challenges.

The growing global concern about environmental threats due to environmental pollution requires the development of environmentally friendly and efficient removal/detection materials and methods. Porphyrin/phthalocyanine (Por/Pc) based porous organic polymers (POPs) as a newly emerging porous material are prepared through polymerizing building blocks with different structures. Benefiting from the high porosity, adjustable pore structure, and enzyme-like activities, the Por/Pc-POPs can be the ideal platform to study the removal and detection of pollutants. However, a systematic summary of their application in environmental treatment is still lacking to date. In this review, the development of various Por/Pc-POPs for pollutant removal and detection applications over the past decade was systematically addressed for the first time to offer valuable guidance on environmental remediation through the utilization of Por/Pc-POPs. This review is divided into two sections (pollutants removal and detection) focusing on Por/Pc-POPs for organic, inorganic, and gaseous pollutants adsorption, photodegradation, and chemosensing, respectively. The related removal and sensing mechanisms are also discussed, and the methods to improve removal and detection efficiency and selectivity are also summarized. For the future practical application of Por/Pc-POPs, this review provides the emerging research directions and their application possibility and challenges in the removal and detection of pollutants.

Novel technique for preparing Ca- and P-containing ceramic coating on Ti-6Al-4V by micro-arc oxidation.

A novel technique for preparing the Ca- and P-containing ceramic coating on Ti-6Al-4V alloy by micro-arc oxidation (MAO) was developed successfully in this paper. In the new technique, Ti alloy first was micro-arc oxidated in P-containing electrolyte, and then it was micro-arc oxidated in Ca-containing electrolyte. This technique can avoid the undesired chemical reaction between Ca-containing salt and P-containing salt in electrolyte. The surface morphologies, composition, and phases of MAO coatings were studied by means of SEM, EDS, and XRD. The results show that the P- and Ca-containing coating on Ti-6Al-4V alloy contains Ti, TiO(2) (rutile), alpha-Ca(PO(3))(2), CaTiO(3), and AlTi(3). There are many small and uniform pores in the coating. Most of these pores are coterminous. The microhardness of the coating is 720 HV and higher than that of Ti-6Al-4V alloy (220 HV). The coating is more wear-resistant than Ti-6Al-4V alloy under the lubricant of the artificial saliva and not easy to desquamate from the substrate of Ti-6Al-4V alloy.

[Corrosiveness of Ti-Fe-Mo-Mn-Nb-Zr alloys in various pH lactic acids].

Variation in pH value of oral cavity circumstance causes decayed tooth. In this paper, corrosions of Ti-Fe-Mo-Mn-Nb-Zr dental alloys in various pH lactic acids were studied by immersion test. In the case of pH=4, which is an acidity slightly larger than that causes decayed tooth, Ti-Fe-Mo-Mn-Nb-Zr alloys are entirely corrosion-resistant, and the corrosion type is pitting. With the increase in acidity, the corrosion-resistance of Ti-Fe-Mo-Mn-Nb-Zr alloys deteriorates, and the corrosion type changes from pitting to intergranular corrosion. Fe ion is the most dissolved substance in impregnation, which means Fe goes against the corrosion-resistance of Ti alloys. Both results of thermodynamics calculation and X-ray photoelectron spectroscopy have shown that Mn2O3, Nb2O5 and TiO2 form oxide film on the surface of Ti-Fe-Mo-Mn-Nb-Zr alloys.

[The influence of Ce on microstructures and mechanics performances of Ti-Fe-Mo-Mn-Nb-Zr alloys].

The influences of Ce on the microstructure and mechanics performances of Ti-Fe-Mo-Mn-Nb-Zr alloys were studied and presented in this paper. The microstructure of no-Ce Ti-Fe-Mo-Mn-Nb-Zr alloy was thick, long and dendritic, and the microstructure of alloy was fined by Ce. With the increase in Ce wt%, the microstructure became equiaxial gradually. Hardness decreased with the increase in Ce wt%. The compression yield strength became greater with the increasing of Ce wt%, but after the Ce wt% increased to a certian degree, the compression yield strength became smaller with the further increasing of Ce wt%. This phenomenon was explained in the light of bond energy and X-ray diffraction experiment. X-ray diffraction experiment showed that the alloys were beta-Ti.

[Evaluation on biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy].

In this study, the general toxicity tests including acute toxicity test, haemolysis test, MTT assay of Ti-Fe-Mo-Mn-Nb-Zr alloys were carried out. The morphology of these cells was also observed under phase-contrast microscope. By using X-ray photoelectron spectroscopy(XPS), the kind and mol% of element in surface film were studied. The kind and concentration of element in dipping fluid were investigated by ICP atomic emission spectrometry. The results showed the primary component is TiO2 in surface film. The dipping fluid of Ti-Fe-Mo-Mn-Nb-Zr alloys contains Fe 0.2-1.07 mg/l and Mn 0.16-0.5 mg/l; such dental materials are beneficial to health. No cytotoxic effect was disclosed by in vitro and in vivo tests. The level of cytotoxicity was grade 0 and 1; the haemolysis degree was 0.558%-0.642%, i.e. less than 5%. The cells growing in the extract showed normal morphology. These data indicate that Ti-Fe-Mo-Mn-Nb-Zr alloy, as a dental material, has good biocompatibility.

Effects of Ce on the short-term biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy for dental materials.

Effects of Ce on the short-term biocompatibility of Ti-Fe-Mo-Mn-Nb-Zr alloy designed for implant materials were studied by acute toxicity test, hemolytic test, and MTT assay. The elements and their concentration in surface films and extraction media of Ti alloys were investigated with XPS and ICP, respectively. The primary compositions of the surface films of Ti alloys with 0.3% Ce and without Ce were TiO2 and Nb2O5. There were 0.2 mg/l Fe and 0.16 mg/l Mn in the extraction medium of Ti alloy without Ce, while 0.27 mg/l Fe and 0.87 mg/l Mn in the extraction medium of Ti alloy with 0.3% Ce. The concentrations of Fe and Mn in the medium were too low to have any significant effects on human health. There was no sign of cytotoxicity in these tests. The cytotoxicity levels of Ti alloys without Ce and with 0.3% Ce were graded 0 and 1, respectively. The hemolytic degrees of Ti alloys without Ce and with 0.3% Ce were 0.558% and 0.67%, respectively. The cells being incubated in the extraction medium were normal. These phenomena indicated that Ce was innocuous within the concentration range of this study. In addition, the hemolytic ratio and toxicity level of Ti alloy with 0.3% Ce were a little higher than that of Ti alloy without Ce. This meant that Ce would slightly increase the toxicity of Ti alloy.