Effects of Sludge Retention Time on the Performance of Anaerobic Ceramic Membrane Bioreactor Treating High-Strength Phenol Wastewater.

Anaerobic ceramic membrane bioreactor (AnCMBR) is an attractive alternative for the treatment of high-strength phenol wastewater, but the effects of sludge retention time (SRT) on the performance and membrane fouling are still unclear. The results indicated that the AnCMBR was successfully employed to treat high-strength wastewater containing 5 g phenol L-1. The removal efficiencies of phenol and chemical oxygen demand (COD) reached over 99.5% and 99%, respectively, with long SRT and short SRT. SRT had no obvious effect on the performance of the AnCMBR treating high-strength phenol wastewater with long time operation. The strong performance robustness of AnCMBR benefited from the enrichment of hydrogenotrophic methanogens and syntrophic phenol-degrading bacteria. However, the decline of SRT led to a more severe membrane fouling in the AnCMBR, which was caused by the small size of sludge flocs and high concentration of protein in the biopolymers. Therefore, this work presented a comprehensive insight to the feasibility and robustness of the AnCMBR for treating high-strength phenol wastewater.

Comparison, association, and risk assessment of phthalates in floor dust at different indoor environments in Delaware, USA.

This study aimed to compare and assess phthalate contamination in various indoor environments. In this study, 44 floor dust samples from different indoor environments in Delaware, USA were collected and analyzed for 14 phthalates using gas chromatography-mass spectrometry. Phthalates were detected in all dust samples with the total concentration ranging from 84 to 7117 mg kg(-1). DEHP (di-2-ethylhexyl phthalate), BzBP (benzylbutyl phthalate), DBP (dibutyl phthalate), and DiBP (di-isobutyl phthalate) were both the most frequently and abundantly detected phthalates. The average concentration of total phthalates in dust from offices, student dorms, gyms, stores, and daycare centers was found to be significantly or insignificantly (P = 0.05) higher than that in dust from houses and apartments. Plastic flooring materials and the application of floor care chemical products were positively associated with total phthalate concentration in floor dust. Toxicological risk assessment indicated that an investigated daycare center in this study was the only indoor environment that may cause the intake amount of DEHP of infants, toddlers, and children via dust ingestion to exceed the reference dose established by the U.S. Environmental Protection Agency (USEPA). Regular monitoring on phthalate contamination in sensitive indoor environments is recommended.

Modification of fluorescence staining method for small-sized microplastic quantification: Focus on the interference exclusion and exposure time optimization.

Microplastics are an emerging pollutant of global concern, and fluorescence staining as an efficient method for small-sized microplastic qualification often undergoes the serious interference from external environments. The key steps affecting the accuracy of fluorescent staining and the corresponding quality assurance measures were rarely known. Therefore, this study took the Nile Red/DAPI co-staining method as an example to explore the key factors affecting its accuracy and effective measures to avoid interference. High background microplastic contamination in typical lab waters (up to 1115 MP/L), glass fiber filter membrane and glassware were identified as dominant factors affecting microplastic quantification. The background microplastics in lab waters mainly originated from the process of water production and storage. A simple filtration process removed 99% of the background microplastic in the lab waters. After burning at 500 °C for 1 h, the microplastic contamination in the filter membrane and glassware was completely eliminated. H2O2 pretreatment and exposure time caused erroneous microplastic size assessment, and were suggested to be set at 48 h and 10 ms, respectively. During the extraction process, the residue in beakers reached ~ 20% and > 50% for 5 µm and 20 µm sized microplastics, respectively, greatly contributing to the microplastic loss. The comprehensive modified measures caused microplastic concentrations in the three typical samples detected by Nile Red/DAPI co-staining method to decrease by 65.7 - 92.2% and to approach the micro-Raman results. This study clarified the reasons for interfering with quantitative microplastics by fluorescent staining and the effective measures to avoid interference, which were conducive to improving the accuracy of quantitative methods of microplastics.

Roles of microplastic-derived dissolved organic matter on the photodegradation of organic micropollutants.

Microplastic-derived dissolved organic matter (MP-DOM) is ubiquitous in water environment and exhibits photosensitivity. However, little is known about the effects of MP-DOM on the photodegradation of organic micropollutants in natural water. In this study, we investigated the effect of MP-DOM derived from two typical plastics, i.e., polystyrene (PS), and polyethylene (PE), on the photodegradation of a typical organic micropollutants sulfamethoxazole (SMX) in a simulative natural water system. MP-DOM exerted a significant inhibition on the SMX photodegradation, mainly attributed to the direct photolysis inhibition of SMX caused by the inner filter effect and the complexation effect. Despite the enhanced reactive oxygen species (ROS) generation with the increase of their steady-state concentration by 41.1 - 160.7 %, PS-DOM exhibited high oxidation resistance, causing an inhibition on the photodegradation of SMX probably through transferring electrons to the SMX intermediates. This study helps to deepen the understanding of microplastic photochemical behavior in natural water.

Preparation, characterization, and pharmacodynamics of thermosensitive liposomes containing docetaxel.

A novel thermosensitive liposome (TL) containing docetaxel (DTX) was designed to enhance DTX-targeted delivery and antitumor effect. TL loading DTX (DTX-TL) were prepared by thin film hydration. The mean particle size of the liposomes was about 100 nm, and the drug entrapment efficiency was more than 95%. The phase transition temperature of liposomes was about 42 °C. In vitro drug release showed that drug released at 37 °C was obviously less than that at 42 °C. For in vivo experiments, the human breast tumor model was established by subcutaneous xenotransplantation on nude mice; liposomes and injection containing DTX were injected i.v. in nude mice, followed by exposure of the tumors to hyperthermia (HT) for 30 min after administration. The tumor inhibition ratio of DTX-TL group was significantly higher than the normal injection group. Combining TL with HT enhanced the delivery of DTX and thereby its antitumor effects. The liposomes reported in this paper could potentially produce viable clinical strategies for improved targeting and delivery of DTX for the treatment of breast cancer.