Optical effects of graphene addition on adhesives for orthodontic lingual retainers.

The objective of this study was to determine the effects on the colour of adding increasing concentrations of graphene to orthodontic fixed retainer adhesives and to evaluate changes in optical transmission during light curing and the resultant degree of conversion. Two different types of adhesives commonly used for fixed retainers were investigated: A packable composite (Transbond) and a flowable composite (Transbond Supreme). Graphene was added to the adhesives in three different concentrations (0.01, 0.05, and 0.1 wt%). Adhesives without graphene addition were set as control groups. A Minolta colourimeter was used to measure the colour and translucency parameters. Irradiance transmitted during curing was quantified using MARC Light Collector. Fourier-transform infrared spectroscopy was used to record degree of conversion. Data were statistically analysed with the Student's t-test and one-way ANOVA with Tukey's tests (α = 0.05). The findings showed that incorporating graphene darkened the adhesive colour significantly and reduced translucency. As the graphene concentration reached 0.1 wt%, samples became opaque; yet, no adverse effect on degree of conversion was observed. The addition of graphene reduces optical transmission of lingual retainer adhesives; the effect increases with graphene concentration.

Application of Silver Nanoparticles to Improve the Antibacterial Activity of Orthodontic Adhesives: An In Vitro Study.

There is a significant change in the bacterial plaque populations in the oral cavity during and after orthodontic treatment. Numerous studies have demonstrated that 2−96% of patients could increase the risk of white spot lesions. Streptococcus mutans and Lactobacilli ssp. are responsible for these white spot lesions. In this work, silver nanoparticles (AgNPs) with a diameter of 11 nm and dispersed in water were impregnated onto three different commercial orthodontic adhesives at 535 µg/mL. The shear bond strength (SBS) was assessed on 180 human premolars and metallic brackets. The premolars were divided into six groups (three groups for the commercial adhesives and three groups for the adhesives with AgNPs). All the groups were tested for their bactericidal properties, and their MIC, MBC, and agar template diffusion assays were measured. After adding AgNPs, the SBS was not significantly modified for any adhesive (p > 0.05), and the forces measured during the SBS did not exceed the threshold of 6 to 8 MPa for clinical acceptability in all groups. An increase in the bactericidal properties against both S. mutans and L. acidophilus was measured when the adhesives were supplemented with AgNPs. It was concluded that AgNPs can be supplement commercial orthodontic adhesives without modifying their mechanical properties with improved bactericidal activity.

Genotoxic and cytotoxic potential of methacrylate-based orthodontic adhesives.

OBJECTIVES: The biocompatibility of methacrylate-based adhesives is a topic that is intensively discussed in dentistry. Since only limited evidence concerning the cyto- and genotoxicity of orthodontic adhesives is available, the aim of this study was to measure the genotoxic potential of seven orthodontic methacrylate-based adhesives. MATERIALS AND METHODS: The XTT assay was utilized to determine the cytotoxicity of Assure Plus, Assure Bonding Resin, ExciTE F, OptiBond Solo Plus, Scotchbond Universal Adhesive, Transbond MIP, and Transbond XT after an incubation period of 24 h on human gingival fibroblasts. We also performed the γH2AX assay to explore the genotoxic potential of the adhesives within cytotoxic dose ranges after an incubation period of 6 h. RESULTS: The XTT assay showed a concentration-dependent reduction in cell viability. The decrease in cellular viability was in the same dose range most significant for Assure Plus, rendering it the adhesive material with the highest cytotoxicity. Employing the γH2AX assay, a concentration-dependent increase in H2AX phosphorylation was detected, indicating induction of DNA damage. CONCLUSIONS: For most products, a linear correlation between the material concentration and γH2AX foci was observed. The most severe effect on γH2AX focus induction was found for Transbond MIP, which was the only adhesive in the test group containing the co-initiator diphenyliodonium hexafluorophosphate (DPIHP). CLINICAL RELEVANCE: The data indicate that orthodontic adhesives, notably Transbond MIP, bear a genotoxic potential. Since the study was performed with in vitro cultivated cells, a direct translation of the findings to in vivo exposure conditions should be considered with great diligence.

The influence of adding modified zirconium oxide-titanium dioxide nano-particles on mechanical properties of orthodontic adhesive: an in vitro study.

BACKGROUND: The purpose of this in-vitro study was to examine the effect of incorporating different concentrations of Zirconium oxide-Titanium dioxide (ZrO2-TiO2) nanoparticles, which can have antibacterial properties, on the mechanical properties of an orthodontic adhesive. METHODS: ZrO2-TiO2 (Zirconium oxide, HWNANO, Hongwu International Group Ltd, China) -Titanium dioxide, Nanoshell, USA) nanopowder were incorporated into orthodontic adhesive (Transbond XT, 3 M Unitek, Monrovia, USA) with different concentrations (0.5% weight nonofiller and 1% weight nanofiller). The size of nanoparticle was 70-80 nm for ZrO2 and less than 50 nm for TiO2. For measuring the shear bond strength of the three groups of orthodontic adhesives [Transbond (control), Transbond mixed with 0.5% weight ZrO2-TiO2, and Transbond mixed with 1% weight ZrO2-TiO2], 30 freshly extracted human first premolars were used and bonded with stainless steel metal brackets (Dentaurum®, Discovery®, Deutschland), using the 3 orthodontic adhesives and 3 M Unitek; Transbond TM Plus Self-Etching Primer (10 samples in each group). The recorded values of compressive strength and tensile strength (measured separately on 10 samples of orthodontic adhesives (add the 3 D size of sample, light cured for 40 s on both sides) of each orthodontic adhesives), as well as the shear bond strength in Mega Pascal unit (MPa) were collected and exposed to one-way analysis of variance (ANOVA) and Tukey's post-hoc tests. RESULTS: orthodontic adhesive with 1% weight ZrO2-TiO2 showed the highest mean compressive (73.42 ± 1.55 MPa, p: 0.003, F: 12.74), tensile strength (8.65 ± 0.74 MPa, p: 0.001, F: 68.20), and shear bond strength (20.05 ± 0.2 MPa, p: 0.001, F: 0.17). CONCLUSIONS: Adding ZrO2-TiO2 nanoparticle to orthodontic adhesive increased compressive strength, tensile strength, and shear bond strength in vitro, but in vivo studies and randomized clinical trials are needed to validate the present findings.

The effect of antimicrobial agents on bond strength of orthodontic adhesives: a meta-analysis of in vitro studies.

Antimicrobial orthodontic adhesives aim to reduce white spot lesions' incidence in orthodontic patients, but they should not jeopardizing its properties. Systematic review and meta-analysis were performed to answer the question whether the association of antimicrobial agents with orthodontic adhesives compromises its mechanical properties and whether there is a superior antimicrobial agent. PubMed and Scopus databases. In vitro studies comparing shear bond strength of conventional photo-activated orthodontic adhesives to antimicrobial photo-activated orthodontic adhesives were considered eligible. Search terms included the following: orthodontics, orthodontic, antimicrobial, antibacterial, bactericidal, adhesive, resin, resin composite, bonding agent, bonding system, and bond strength. The searches yielded 494 citations, which turned into 467 after duplicates were discarded. Titles and abstracts were read and 13 publications were selected for full-text reading. Twelve studies were included in the meta-analysis. The global analysis showed no statistically significant difference between control and experimental groups. In the subgroup analysis, only the chlorhexidine subgroup showed a statistically significant difference, where the control groups had higher bond strength than the experimental groups. Many studies on in vitro orthodontic bond strength fail to report test conditions that could affect their outcomes. The pooled in vitro data suggest that adding an antimicrobial agent to an orthodontic adhesive system does not influence bond strength to enamel. It is not possible to state which antimicrobial agent is better to be associated.

Assessment of cytotoxicity, odontoblast-like differentiation, shear bond strength, and microhardness of four orthodontic adhesive composites.

PURPOSE: To determine and compare the cytotoxicity, odontoblast-like differentiation, shear bond strength (SBS) and Vickers microhardness of four commercial light-cured orthodontic adhesives. METHODS: The orthodontic resins selected were Transbond XT - GI, Transbond Plus Color Change - GII (both from 3M Unitek), Enlight - GIII and Blugloo - GIV (both from Ormco). Samples were prepared, and leached monomers were obtained. Cytotoxicity was evaluated using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay and deposited calcium was analyzed using Alizarin red staining (ARS). SBS and the adhesive remnant index (ARI) were determined using 120 human premolars. The Vickers microhardness test was performed on the resin discs. RESULTS: All adhesives showed moderate to severe cytotoxicity (21-37%) and promoted similar formation of calcium deposits. A SBS of 6-8 MPa was achieved only by Blugloo (7.1 ± 2.4 MPa), and Enlight showed the lowest Vickers hardness score (40 ± 2.5 HV). Transbond Plus Color Change (score 0 = 42.9%) and Blugloo (score 0 = 46.4%) showed better ARI scores than Transbond XT (score 0 = 7.1%) and Enlight (score 0 = 3.6%). CONCLUSION: On the basis of the properties evaluated, Blugloo seems to be the best option.

The Synthesis, Characterization, and Assessment of Antibacterial Properties of an Orthodontic Adhesive Containing Cerium-Substituted Hydroxyapatite Nanoparticles: An In Vitro Study.

Introduction White spot lesions (WSLs) are early enamel caries lesions often seen in individuals receiving fixed orthodontic treatment. These lesions occur due to the buildup of plaque and the colonization of bacteria. WSL formation can be prevented by adequate oral hygiene measures and by the incorporation of antimicrobial nanoparticles (NPs) in orthodontic appliances and bonding systems. The aim of this research was to synthesize cerium-substituted hydroxyapatite nanoparticles (Ce-HAp NPs), characterize them, and assess their antimicrobial activity. Materials and methods This in vitro investigation involved the preparation of Ce-HAp NPs using the co-precipitation method, followed by their characterization using scanning electron microscope (SEM), energy-dispersive X-ray (EDAX), and Fourier transform infrared (FTIR). The NPs were prepared and subsequently added to an orthodontic adhesive. Antibacterial testing was conducted using the disc diffusion method against common oral pathogens (Staphylococcus aureus, Lactobacillus acidophilus, and Streptococcus mutans). The zones of inhibition were measured for two different concentrations of the adhesive. Results  The Ce-HAp NPs were successfully prepared and had an irregular agglomerated shape, measuring 63 nm in size. The major characteristic chemical groups of Ce-HAp were PO43-, OH-, and CO32-, and it was confirmed by the FTIR spectrum. The EDAX results of the synthesized NPs showed theoretical weight percentages (Wt%) of O, 52.6%; Ca, 20.9%; P, 11.8%; C, 10.3%; and Ce, 4.3%. A higher concentration of 40 µg/mL (30 mm for S. aureus and L. acidophilus and 25 mm for S. mutans) showed good antibacterial activity against the tested bacterial strains, compared to control antibiotics. Conclusion Cerium oxide (CeO2)-HAp NPs were prepared and incorporated into an orthodontic adhesive. The prepared adhesive exhibited effective antibacterial activity against prevalent oral pathogens.

In-Vitro Investigation of the Shear Bond Strength of Different Orthodontic Adhesives to Enamel.

Background: The shear bond strength (SBS) of orthodontic adhesives to enamel is a critical factor in the success of orthodontic treatment. Various adhesives are available in the market, each with different trade names and claimed properties that could influence their bond strength. Understanding these differences is essential for clinical decision-making. Materials and Methods: In this in-vitro study, 60 freshly extracted human premolars were collected and randomly divided into four groups: Group A (Adhesive X-Trade Name: BondPlus), Group B (Adhesive Y-Trade Name: OrthoBond), Group C (Adhesive Z-Trade Name: PowerBond), and Group D (Control). The enamel surfaces were cleaned, polished, and etched following standard protocols. Orthodontic brackets were bonded to the teeth using the respective adhesives according to the manufacturer's instructions. A universal testing machine was employed to measure the SBS, and the data were analyzed using ANOVA with post-hoc tests. Results: The mean SBS values (MPa) were as follows: Group A = 15.2, Group B = 14.8, Group C = 16.5, and Group D (Control) =10.3. Statistical analysis revealed significant differences among the groups (P < 0.05). Post-hoc tests indicated that Group C exhibited significantly higher SBS compared to the other groups. Conclusion: Our findings suggest that among the orthodontic adhesives tested, PowerBond demonstrated superior shear bond strength to the enamel. However, further research is warranted to explore other aspects of adhesive performance and clinical implications.

Effect of Different Primers on the Shear Bond Strength of Orthodontic Brackets Bonded to Reinforced Polyetheretherketone (PEEK) Substrate.

This in vitro study assessed the effect of different primers on the shear bond strength (SBS) and adhesive remnant index (ARI) of orthodontic brackets bonded to reinforced polyetheretherketone (PEEK) substrate. A total of 40 specimens were randomly distributed to two groups based on the primer used for orthodontic bonding: group 1 (control)-Transbond XT adhesive with Visio.link primer and group 2 (test)-orthodontic adhesive (Transbond XT) with traditional orthodontic primer. After bonding, specimens were thermocycled followed by SBS testing and ARI scoring of debonded specimens. Data were analyzed using the unpaired independent t-test and the Chi-square test. Group 1 specimens showed significantly higher SBS values (21.38 ± 1.48 MPa) compared to group 2 specimens (18.63 ± 1.29 MPa) (p < 0.0001). Adhesive remnant index scores showed no significant variations in bond failure modes and distributions between groups. The SBS obtained by the tested primers exceeded the clinically recommended value. Consequently, there is a comparable clinical application for both tested primers in orthodontic bonding, especially the traditional orthodontic primer, where the availability of Visio.link in clinical practice is not ensured.

Physico-Mechanical Properties and Bonding Performance of Graphene-Added Orthodontic Adhesives.

This study aimed to assess the key physico-mechanical properties and bonding performance of orthodontic adhesives with graphene addition for bonding a fixed retainer. Transbond LR (3M) and Transbond LV (3M) with no graphene were set as the control groups. Graphene was added into LR and LV at concentrations of 0.01 wt%, 0.05 wt% and 0.1 wt%. The stickiness of the uncured samples (n = 5) and real-time degree of conversion (DC) of the samples (n = 3) were measured over a 24-h period using Fourier-transform infrared spectroscopy. The hardness and other mechanical parameters, including the Martens hardness (HM), indentation modulus (EIT), elastic index (ηIT) and creep (CIT), were measured (n = 5). To measure the shear bond strength (SBS), adhesive composites were applied using a mold to bond the retainer wire to the lingual surfaces of bovine incisors (n = 10). Fracture modes subsequent to the SBS test were examined under light microscopy. Statistical analysis was conducted using ANOVA and Tukey tests (α = 0.05). In the LR groups, the LR + 0.01 showed the highest SBS (12.6 ± 2.0 MPa) and HM (539.4 ± 17.9 N/mm2), while the LV + 0.05 (7.7 ± 1.1 MPa) had the highest SBS and the LV + 0.1 had the highest HM (312.4 ± 17.8 N/mm2) among the LV groups. The most frequent failure mode observed was adhesive fracture followed by mixed fracture. No statistical difference was found between the graphene-added groups and the control groups in terms of the EIT, ηIT and CIT, except that the CIT was significantly lower in the LR + 0.01 than in the control group. Graphene addition had no significant adverse effect on the stickiness and DC of both LR and LV.

Detection and Identification of Various Microplastics in Different Orthodontic Adhesives.

Background Microplastics are acknowledged as significant environmental contaminants. The clinical use of dental materials, particularly adhesives containing plastic polymers, can give rise to the production of plastic micro- and nanoparticles, which subsequently find their way into the environment. The aim of the study was to detect different microplastics and identify them in various orthodontic adhesives. Materials and methods Four different light cure orthodontic adhesives, including Transbond XT (3M Unitek, Monrovia, CA), Ormco Enlight (Ormco, Orange, CA), Orthofix SPA (Orthofix, Verona, Italy), and Aqualine LC (Tomy International Inc, Tokyo, Japan), were collected and placed in separate Eppendorf tubes. Microplastics present in each adhesive were identified using scanning electron microscopy. Subsequently, each specimen was suspended in hydrogen peroxide, placed within a shaking incubator, and analyzed using Fourier transform infrared spectroscopy (FTIR) to identify the type of polymer. Results The scanning electron microscope shows the surface morphology and the most predominant types of microplastics identified were fibers, fragments, and pellets. FTIR results showed the presence of several major functional groups, including hydroxyl, amine, ester, fluoro, and halo groups. Conclusion When contrasted with the quantity of microplastic waste generated by other sectors like the textile, cosmetic, and fishing industries, the microparticulate waste stemming from dental adhesives has a minimal effect on environmental deterioration. Strategies for addressing this concern should give precedence to reducing the use of these materials and adopting effective recovery methods, which could potentially involve recycling processes.

The effect of light curing time and intensity on the bond strength and fracture resistance of orthodontic adhesive.

Background: This study aimed to measure the shear bond strength and compressive strength of orthodontic adhesives at different curing times and intensities. Methods: Ninety extracted human premolars were used. Orthodontic brackets were bonded on the buccal surface of the teeth with orthodontic adhesive light-cured using VRN-VAFU LED curing light at different curing times (1, 3 and 5 seconds) and intensities (1000, 1600 and 2300 mW/cm2 ). A universal testing machine was used to measure the shear bond strength. The ratio of the adhesive remnant and compressive strength of the orthodontic adhesive, at each curing time at the different intensities, were also evaluated. The results were statistically analyzed using one-way analysis of variance followed by Tukey's test. Results: The lowest bond strength values (6.4, 9.9 and 12.6 MPa) were recorded with 1000 mW/ cm2 intensity (at all curing times) in comparison with the other intensities (P<0.05). Increasing the curing time significantly increased the bond strength of the orthodontic brackets (P<0.05), except when the curing time was increased from 3 sec to 5 sec at 1600 mW/cm2 intensity. The highest compressive strength values (130.3, 147.1 and 174 MPa) were recorded at 2300 mW/ cm2 intensity (at all curing times) compared to the other intensities (P<0.05). The highest values of the ratio of the adhesive remnants were recorded at 1000 mW/cm2 intensity (at all curing times) compared to the other intensities (P<0.05). Conclusion: Although, increasing the curing time and\or the curing intensity has a positive effect on the bond strength and compressive strength of the orthodontic adhesive, it might be possible to suggest reducing the curing time of orthodontic adhesive to 1 sec at curing intensity of 2300 mW/cm2.

A novel orthodontic adhesive containing zinc-doped phosphate-based glass for preventing white spot lesions.

OBJECTIVES: This study aimed at demonstrating the remineralization effect of the enamel around the brackets to aid reduction in white spot lesions (WSLs) with use of zinc-doped phosphate-based glass (Zn-PBG) containing orthodontic adhesives. METHODS: Zn-PBG powder was synthesized, and particle morphology, size, and density were evaluated. Orthodontic adhesives with increasing loading percentage of Zn-PBG powder were prepared: ZnPG3 (3 wt.%), ZnPG6 (6 wt.%), and ZnPG9 (9 wt.%). Brackets were bonded on the etched enamel surface and stored in distilled water (DW) for 1 h. Following, Shear bond strength (SBS) along with adhesive remnant index were analyzed. The release of calcium (Ca), phosphorus (P), and zinc (Zn) from adhesive specimens in DW was evaluated after 7, 15 and 30 days of immersion. The remineralization effect was confirmed by microhardness and surface morphology analysis with scanning electron microscopy. RESULTS: The SBS value was observed between 20 and 22 MPa on enamel surface. The concentration of Ca, P and Zn released in DW increased with loading percentage of Zn-PBG. The microhardness increased in the experimental groups after immersion in artificial saliva for 7 days. Apatite-like crystal formation was observed after 30 days in the ZnPG 9 group. CONCLUSIONS: The orthodontic adhesive containing Zn-PBG with an optimal SBS performance has an enamel remineralization effect, and therefore can aid in prevention of WSLs. CLINICAL SIGNIFICANCE: The orthodontic adhesive containing Zn-PBG is clinically advantageous as it can promote remineralization and resist the formation of WSLs that may occur during orthodontic therapy.

Clinical performance of light-cured orthodontic adhesives for bonding brackets - an in-vitro study.

Background: The dental profession is seeing a constant influx of new adhesive systems from manufacturers, each claiming to be more dependable than the last. This study assessed the bond strength and adhesive remnants of different light-cured adhesives used for bonding metal brackets to teeth. Methods: 80 extracted maxillary premolars with the sound crown structure were acid etched and bonded with brackets on their buccal surfaces utilizing primer and light-cured adhesives into four equal groups, which are Transbond XT, Heliosit, Enlight, and Bracepaste. Shear bond strength (SBS) for de-bonding the brackets were evaluated with Instron- testing machine after 48 hours. The de-bonded samples' adhesive remnant index (ARI) scores were also measured. Results: The maximum mean SBS was found for Transbond XT (12.91 ± 2.0 MPa), followed by Bracepaste (12.87 ± 1.59 MPa), Enlight (11.77 ± 1.87 MPa), and lowest for Heliosit (10.93 ± 1.71 MPa). According to the four point scale, adhesive remnant index (ARI), Transbond XT has the least adhesive residue left on the tooth, followed by Heliosit. Enlight and Bracepaste have a similar distribution of adhesive, with both having a maximum amount left. Conclusion: It can be inferred that all groups involved demonstrated a satisfactory level of bond strength from a clinical perspective. Transbond XT is the preferred orthodontic adhesive over the other three adhesives due to its superior SBS and ARI properties.

Comparison of microleakage and shear bond strength of ribbon and twisted wire retainers bonded on human mandibular incisors with two different types of adhesives with and without primer: An in-vitro study.

BACKGROUND AND OBJECTIVES: Shear bond strength and microleakage are the success factors of fixed retainers. Recently, primer-free composites were introduced to reduce chair time. The main objectives of this study were to compare the shear bond strength (SBS) and microleakage of GC Ortho ConnectTM Flow (OF) and TransbondTM XT (TXT) with two types of common retainer wires (0.0175-inch twisted wire and 0.028×.0.008-inch ribbon dead soft wire retainers). The secondary objectives of the study were to compare enamel-adhesive interface and wire-adhesive interface microleakages. MATERIALS AND METHODS: This in vitro study was conducted on 132 human mandibular incisors (96 for bond strength and 36 for microleakage). The teeth were randomly divided into four groups for use of ribbon and twisted wires with OF and TXT adhesives. The bond strength was measured by a universal testing machine. Microleakage was evaluated by the dye penetration test using 0.05% fuchsine. Data were analysed by two-way ANOVA (alpha=0.05). RESULTS: No significant difference was noted in bond strength among the four groups (P>0.05). However, the microleakage of OF was significantly higher than that of TXT at both the enamel-adhesive and wire-adhesive interfaces (P<0.001). The microleakage at the wire-adhesive and enamel-adhesive interface was not significantly different in groups 1 and 4 and was significant in group 2 and 3. CONCLUSION: Type of adhesive significantly affected the microleakage, and OF resulted in higher microleakage than TXT at both the enamel-adhesive and wire-adhesive interfaces. Type of wire had no significant effect on microleakage. Although OF showed comparable SBS to TXT, its higher microleakage may compromise its successful long-term clinical service.

Impact of fluoride-releasing orthodontic adhesives on the shear bond strength of orthodontic brackets to eroded enamel following different surface treatment protocols.

PURPOSE: To assess the impact of enamel surface treatment protocols and the types of adhesive materials on the shear bond strength (SBS) of brackets to eroded enamel substrate. MATERIALS AND METHODS: Eighty extracted premolars were randomly assigned to four main groups in which group C (no treatment) was the control group. The remaining groups were exposed to an erosion challenge through short-term acidic exposure to HCl solution (0.01 M, pH 2.3) for 30 s, with an agitation speed of 50 rpm at an environmental temperature of 25°C. The eroded enamel surface within each group was treated as follows: group N received no treatment; in group P, the eroded enamel was treated with 35% phosphoric acid (Ultradent Products, South Jordan, UT, USA) for 15 s, followed by a rinse for 10 s; and in group F, the eroded enamel was treated with fluoride gel (Bifluorid 12; Voco-GmbH, Cuxhaven, Germany) for 4 min. The brackets were bonded with either a resin composite adhesive (Transbond XT; light-cure adhesive, 3M Unitek, CA, USA) or resin-modified glass ionomer cement (Fuji Ortho LC-GC Corporation, Japan). The specimens were tested for SBS, and the bond failure was assessed according to the adhesive remnant index (ARI). Analysis of variance (ANOVA) and Tukey's post-hoc tests (P < 0.05) were used to compare the SBS of the groups. The ARI values between the groups were recorded. RESULTS: Statistically significant differences were found among the tested variables (P < 0.05). Group P showed the highest mean SBS values regardless of the type of adhesive used, and the difference was statistically significant (P < 0.05). The application of the fluoride gel showed no statistically significant improvement in SBS values. The failure mode distribution among the test groups indicated that failures at the adhesive-bracket interface were predominant in group C compared with the other study groups. CONCLUSIONS: Fluoride pretreatment, which was used to remineralize the eroded enamel surfaces before bonding, resulted in a decrease in the SBS of the orthodontic brackets in vitro compared with the other treated groups. The use of fluoride-releasing adhesive also enhances bonding to the eroded enamel surfaces.

Knowledge, attitude, and awareness regarding the use of composites for orthodontic purposes among dental students.

The aim of the study was to determine the knowledge, attitude, and practice regarding the use of composites for orthodontic purposes among dental students. The questionnaire was designed to evaluate knowledge, attitude, and awareness. Google Forms was used for the distribution of questions. This is a questionnaire survey based on knowledge, attitude, and awareness regarding the use of composites for orthodontic purposes among dental students; 86% of them had awareness regarding the use of composites for orthodontic purposes, wherein the remaining 14% were not aware. Considering the limitations of the study groups, we can conclude that the knowledge, attitude, and awareness regarding the use of composites for orthodontic purposes among dental students were good. However, there is still a lack of knowledge in few perspectives which can be overcome with continuous dental education programs and lectures.

Bioinspired Anti-demineralization Enamel Coating for Orthodontics.

White spot lesions and enamel cracks are the 2 most prominent diseases that occur after orthodontic treatment and are caused by enamel demineralization from accumulated bacterial biofilms and/or enamel damage caused by the removal of residual adhesive after bracket debonding. Inspired by the self-assembled amelogenin nanoribbons in enamel, we developed an enamel coating with a self-assembling antimicrobial peptide, D-GL13K, to simultaneously reduce demineralization and residual adhesive. The self-assembled amphiphilic nanoribbons significantly increased the hydrophobicity of the etched enamel, which reduced the permeability of the coated enamel surfaces as desired. The antimicrobial activity of this coating was evaluated against Streptococcus mutans by colony-forming unit counting and live/dead assays. The anti-demineralization effect was demonstrated by the reduced demineralization depth analyzed by optical coherence tomography and the increased Vickers hardness. The coatings did not reduce the shear bond strength but significantly reduced the adhesive remnant index score. This bioinspired enamel coating may provide a new strategy for preventing white spot lesions and enamel cracks after orthodontic treatment.

Effect of different resin removal methods on enamel after metal and ceramic bracket debonding : An in vitro micro-computed tomography study.

PURPOSE: The aim of this study was to conduct an in vitro evaluation of the effects of different adhesive debonding and polishing techniques performed after metal and ceramic bracket removal on enamel using micro-computed tomography (micro-CT). METHODS: This study was performed on 42 extracted maxillary first premolars divided into 2 main groups and 6 subgroups as follows: metal (group 1) or ceramic (group 2) brackets were bonded to the teeth, then, after debonding, one of three different methods was used to remove the residual adhesive: tungsten carbide burs with pumice (A), fiber-reinforced composite burs and polishing paste (B), or Sof-Lex discs (C; 3M Dental, St Paul, MN, USA). The samples were evaluated by micro-CT before bracket bonding (T0) and after resin removal (T1). Demineralization area, demineralization depth, demineralization volume, mineral density, and mineral volume were measured. RESULTS: At T1, demineralization area was significantly larger in groups 1A and 2A compared to groups 1B, 1C, 2B, and 2C (P = 0.001). Group 2A (ceramic bracket/tungsten carbide-pumice) had the highest demineralization volume (P = 0.001). When the groups were compared in terms of change from T0 to T1, groups 1A and 2A showed significantly larger changes in demineralization area compared to the other 4 groups (P = 0.001). The increase in demineralization volume was larger in group 2A compared to all other groups (P = 0.001). CONCLUSION: All resin removal methods damaged the enamel surface to varying degrees. Regardless of bracket type, the use of tungsten carbide and pumice should be avoided when cleaning the tooth surface after debonding. Use of composite burs and Sof-Lex discs in particular after the debonding of ceramic brackets will help minimize damage.

Comparison of the debonding force of metal, glass and polyethylene Fiber reinforced composite retainers: Mechanical and finite element analyses.

OBJECTIVE: The studies evaluating the efficiency of fiber reinforce composite (FRC) retainers are few and contradictory. This study aimed to compare the debonding force of metal, glass FRC (GFRC) and polyethylene FRC (PFRC) retainers, assess the interactions between the materials and forces, and pattern of load distribution by finite element analysis (FEA). MATERIALS AND METHODS: Forty-eight sound lower incisors were collected and randomly assigned to 3 groups (n=8; each sample included 2 teeth). Next, 15mm of the three retainers (multi-stranded metal wire, GFRC, and PFRC) were bonded to the lingual surface of the teeth and debonding force was measured by a universal testing machine. For FEA, 3D models were designed. The data related to geometrical models and material properties were transferred to ANSYS software. A 187-Newton load was applied to the incisal edge of the two centrals. Then different parameters were assessed. The three groups were compared by one-way Anova and Tukey's test. Type one error was considered to be 0.05. RESULTS: The debonding force decreased in the order: Metal (143.71N)≥GFRC (108.29N)>PFRC (45.08N). The difference between metal retainer and GFRC was not significant. In contrast, PFRC group showed significantly lower debonding force compared to other groups (P<0.05). FEA showed stress peak value in metal-composite interface. Maximum total deformation was noted in central, followed by lateral and canine. CONCLUSIONS: Glass-FRC can serve as an alternative to metal retainers as the difference in debonding force is not significant. However, the difficulty of repairing or replacing the Glass-FRC should be taken into account given the large number of failure in the interproximal dental area.