Polyethylene bearing wear is comparable for cemented and cementless Oxford unicompartmental knee replacements: Ten-year results of a randomized controlled trial.

PURPOSE: There is concern that using cementless components may increase polyethylene wear of the Oxford unicompartmental knee replacement (OUKR). Therefore, this study aimed to measure bearing wear at 10 years in patients from a randomized trial comparing Phase 3 cemented and cementless OUKRs and to investigate factors that may affect wear. It was hypothesized that there would be no difference in wear rate between cemented and cementless OUKRs. METHODS: Bearing thickness was determined using radiostereometric analysis at postoperative, 3-month, 6-month, 1-year, 2-year, 5-year and 10-year timepoints. As creep occurs early, wear rate was calculated using linear regression between 6 months and 10 years for 39 knees (20 cemented, 19 cementless). Associations between wear and implant, surgical and patient factors were analysed. RESULTS: The linear wear rate of the Phase 3 OUKR was 0.06 mm/year with no significant difference (p = 0.18) between cemented (0.054 mm/year) and cementless (0.063 mm/year) implants. Age, Oxford Knee Score, component size and bearing thickness had no correlation with wear. A body mass index ≥ 30 was associated with a significantly lower wear rate (p = 0.007) as was having ≥80% femoral component contact area on the bearing (p = 0.003). Bearings positioned ≥1.5 mm from the tibial wall had a significantly higher wear rate (p = 0.002). CONCLUSIONS: At 10 years, the Phase 3 OUKR linear wear rate is low and not associated with the fixation method. To minimize the risk of wear-related bearing fracture in the very long-term surgeons should consider using 4 mm bearings in very young active patients and ensure that components are appropriately positioned, which is facilitated by the current instrumentation. LEVEL OF EVIDENCE: Level III, retrospective comparative study.

Microporous titanium and hydroxyapatite improve fixation of the tibial wall in unicompartmental knee replacement.

PURPOSE: Cementless Oxford unicompartmental knee replacement (OUKR) is associated with less pain than cemented OUKR 5 years postoperatively. This may be due to improved fixation at the tibial wall, which transmits tension and reduces stress in the bone below the tibial component. This study compares tibial wall fixation with three different types of fixation: cemented, cementless with hydroxyapatite (HA) and cementless with a microporous titanium coat and HA (HA + MPC). METHODS: Three consecutive cohorts were identified (n = 221 cemented in 2005-2007, n = 118 HA in 2014-2015, n = 125 HA + MPC in 2016-2017). Analysis was performed on anterior-posterior radiographs aligned on the tibial component taken 1-2 years postoperatively. Aligned radiographs are needed to see narrow radiolucencies adjacent to the wall. Alignment was assessed with rotation ratio (RR = wall width/internal wall height). Perfect RR is 0.3, and a maximum threshold of 0.5 was used. Quality of fixation to the wall was assessed with fixation ratio (FR = bone wall contact height/total wall height). Notable radiographic features at the tibial wall were also recorded. RESULTS: A total of 33 knees with cement, 37 knees with cementless with HA and 57 knees cementless with HA + MPC had adequately aligned radiographs. Fixation was significantly better with HA compared with cement (55% vs. 25%, p = 0.0016). The microporous coat further improved fixation (81% vs. 55%, p < 0.0001). FR > 80% was achieved in 3% of the cemented implants, 32% of HA and 68% of HA + MPC. In cementless cohorts, features suggestive of a layer of bone that had delaminated from the wall were seen in 8 (22%) HA and 3 (5%) HA + MPC knees. CONCLUSION: Radiographic tibial wall fixation in OUKR is poor with cement. It improves with an HA coating and improves further with an intermediary MPC. Improved tibial wall fixation may explain the lower levels of pain observed with cementless rather than cemented fixation described in the literature, but further clinical correlation is needed. LEVEL OF EVIDENCE: Level III, retrospective cohort study.

Unicompartmental knee arthroplasties: does the type of tibial component selected influence implant survival?

INTRODUCTION: Few information has been published on the survival of unicompartmental knee arthroplasty (UKA) and fixed-bearing tibial components. The aim of this study is to analyze if UKA survival varies according to UKA model used and to analyze the possible risk factors for UKA revision. MATERIALS AND METHODS: A retrospective study analyzing 301 UKAs (ACCURIS, all-polyethylene tibial component, 152; Triathlon PKR, metal-backed tibial component, 149) was performed. Demographic parameters as well as implant survival and cause of prosthetic revision were analyzed. The Kaplan-Meier survival analysis, the log-rank test and the Cox multiple regression were used for the analysis. RESULTS: Average follow-up was 8.1 ± 3.08-years. Average age was 68.1 ± 8.6-years; 70.4% of subjects were women. The ACCURIS UKA group had a UKA revision rate higher compared to the Triathlon PKR group (16/152, 10.6% vs 5/149, 3.4%, respectively; p < 0.001). The main cause of prosthetic revision was aseptic loosening (5/21, 23.8%). All aseptic loosening cases and tibial component collapse were reported with the ACCURIS UKA group. Overall UKA survival was 98.01% (95% CI 95.62-99.1) at 1-year, 94.27% (95% CI 90.95-96.4) at 5-years and 92.38% (95% CI 88.48-94.99) at 10-years' follow-up. There were no differences in the Kaplan-Meier survival curves regarding operated side or affected tibiofemoral compartment (log-rank test = 0.614 and 0.763, respectively). However, Kaplan-Meier survival curve according to UKA model used was different (log-rank test = 0.033). The metal-backed component appeared to be a protector factor for UKA revision when adjusted for age, sex, operated side, and affected tibiofemoral compartment (Hazard Ratio 0.32, p = 0.031). CONCLUSION: Fixed-bearing UKAs showed excellent mid- and long-term survival rates. Aseptic loosening is the main cause of implant failure. PKR group (metal-backed component) seem to be a protector factor to UKA revision when it was compared with ACCURIS UKA group (all-polyethylene tibial component).

Preoperative proximal tibial bone density, bone microarchitecture, and bone turnover are not associated with postoperative tibial component migration in cemented and cementless medial unicompartmental knee replacements: secondary analyses from a randomized controlled trial.

BACKGROUND AND PURPOSE: Cementless arthroplasty fixation relies on early bone ingrowth and may be poor in patients with low proximal tibial bone density or abnormal bone turnover. We aimed first to describe the baseline bone properties in patients undergoing medial unicompartmental knee replacement (UKR), and second to investigate its association with cemented and cementless tibial component migration until 2 years. METHODS: A subset investigation of 2 patient groups from a 3-armed randomized controlled trial was conducted. There were 26 cemented and 25 cementless medial UKRs with twin-pegged femoral components. Volumetric bone mineral density (vBMD) and microstructure of the excised medial tibial plateau were ascertained with µCT. Bone turnover was estimated using dynamic histomorphometry (eroded surface/bone surface = ES/BS, osteoid surface/bone surface = OS/BS, mineralizing surface/bone surface = MS/BS). Tibial component migration in 4 feature points was followed for 2 years with radiostereometry. RESULTS: At the 2-year follow-up, the cementless tibial components migrated 0.38 mm (95% confidence interval [CI] 0.14-0.62) total translation more than the cemented components at the posterior feature point. The greatest migration in the cementless group was subsidence at the posterior feature point of 0.66 mm (CI 0.48-0.84) until 6 weeks, and from 3 months the components were stable. Cemented tibial components subsided very little. Between 1- and 2-year follow-ups, no cementless but 4 cemented tibial components revealed continuous migration. OS/BS was half of the ES/BS. No µCT or histomorphometric parameters showed any clinically relevant correlation with tibial component migration at the posterior feature point for either cemented or cementless UKR at 6 weeks' or 2 years' follow-up after adjustment for age, BMI, and sex. CONCLUSION: Preoperative vBMD, bone turnover, and microstructure were not associated with postoperative tibial component migration of cemented and cementless medial UKR.

Can a Total Knee System Providing 1 mm Increment of Polyethylene Insert Thickness Offer a Clinical Benefit?

Background and Objectives: The purpose of this study was to compare clinical outcomes and polyethylene (PE) insert thickness between total knee arthroplasty (TKA) systems providing 1 mm and 2 mm increments. Materials and Methods: In this randomized controlled trial, 50 patients (100 knees) undergoing same-day or staggered bilateral TKA were randomized to receive a TKA system providing 1 mm increments in one knee (1 mm group) and a TKA system providing 2 mm increments in the other knee (2 mm group). At 2 years postoperatively, Knee Society Score (KSS), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score, Forgotten Joint Score (FJS), range of motion (ROM), and insert thicknesses were compared between the groups. Results: A total of 47 patients (94 knees) participated in follow-up analysis. In each group, patient-reported outcomes improved significantly after TKA (all, p < 0.05). There were no significant differences in patient-reported outcomes. The mean ROM was not significantly different between groups at preoperative and 2-year points. The rate of postoperative flexion contracture ≥ 5° was 2.1% and 4.3%, and the rate of postoperative recurvatum ≥ 5° was 4.3% and 2.1% in the 1 mm group and 2 mm, respectively (all, p = 1.000). Mean insert thickness was significantly thinner in the 1 mm group than the 2 mm group (p = 0.001). The usage rate of a thick insert (≥14 mm) was 12.7% and 38.3% in the 1 mm group and 2 mm group (p = 0.005). Conclusions: The use of a TKA system providing 1 mm PE insert thickness increments offered no clinical benefit in terms of patient reported outcomes over systems with 2 mm increments at 2 years of follow-up. However, the TKA system with 1 mm increments showed significantly thinner PE insert usage. As a theoretical advantage of 1 mm increments has yet to be proven, the mid- to long-term effects of thinner PE insert usage must be determined.

Metal-backed or all-poly tibial components: which are better for medial unicompartmental knee arthroplasty? A propensity-score-matching retrospective study at the 5-year follow-up.

BACKGROUND: This retrospective medium-term follow-up study compares the outcomes of medial fixed-bearing unicompartmental knee arthroplasty (mUKA) using a cemented metal-backed (MB) or an all-polyethylene (AP) tibial component. MATERIALS AND METHODS: The database of our institution was mined for primary mUKA patients implanted with an MB or an AP tibial component (the MB-UKA and AP-UKA groups, respectively) from 2015 to 2018. We compared patient demographics, patient-reported outcome measures (PROMs), and motion analysis data obtained with the Riablo™ system (CoRehab, Trento, Italy). We conducted propensity-score-matching (PSM) analysis (1:1) using multiple variables. RESULTS: PSM analysis yielded 77 pairs of MB-UKA and AP-UKA patients. At 5 years, the physical component summary (PCS) score was 52.4 ± 8.3 in MB-UKA and 48.2 ± 8.3 in AP-UKA patients (p < 0.001). The Forgotten Joint Score (FJS-12) was 82.9 ± 18.8 in MB-UKAs and 73.4 ± 22.5 in AP-UKAs (p = 0.015). Tibial pain was reported by 7.8% of the MB-UKA and 35.1% of the AP-UKA patients (p < 0.001). Static postural sway was, respectively, 3.9 ± 2.1 cm and 5.4 ± 2.3 (p = 0.0002), and gait symmetry was, respectively, 92.7% ± 3.7 cm and 90.4% ± 5.4 cm (p = 0.006). Patient satisfaction was 9.2 ± 0.8 in the MB-UKA and 8.3 ± 2.0 in the AP-UKA group (p < 0.003). CONCLUSIONS: MB-UKA patients experienced significantly better 5-year static sway and gait symmetry outcomes than AP-UKA patients. Although the PROMs of the two groups overlapped, MB-UKA patients had a lower incidence of tibial pain, better FJS-12 and PCS scores, and were more satisfied.

Less wear in deep-dished mobile compared to fixed bearing total knee arthroplasty of the same design at 5-year follow-up: a randomised controlled model-based Roentgen stereophotogrammetric analysis trial.

PURPOSE: The aim of this prospective randomised controlled study was to compare wear characteristics and functional outcome between deep-dished mobile bearing (MB) and fixed bearing (FB) cemented total knee arthroplasty (TKA). We hypothesised that deep-dished MB reduces polyethylene wear and improves patient-reported outcome measures. METHODS: A total of 50 patients were randomised to receive a MB or FB tibia component of the same cemented TKA design. Patients were evaluated over a 5-year follow-up period. Medial and lateral wear were assessed using model-based Roentgen Stereophotogrammetric Analysis (RSA) and compared with the direct postoperative minimal joint space measurement. Functional outcome was assessed by the clinician-derived KSS and OKS, WOMAC, LEAS, and FJS-12. All data were derived using a general linear mixed model. RESULTS: At 5-year follow-up, decreased wear in the MB compared to the FB group was observed on the lateral side (0.07 ± 0.17 mm, p = 0.026), but not on the medial side (0.31 ± 0.055 mm, p = 0.665). Functional outcomes improved with a statistical significant effect over time, with no significant differences between groups (all p > 0.17). CONCLUSION: This model-based RSA study with 5-year follow-up showed that cemented deep-dished MB reduced lateral polyethylene wear as compared to FB in a single TKA system, whilst clinical outcomes were comparable. Longer follow-up is needed to establish clinical implications of these altered wear patterns and determine type of wear. LEVEL OF EVIDENCE: Level 1 randomised controlled trial.

Medial congruent polyethylene design show different tibiofemoral kinematics and enhanced congruency compared to a standard symmetrical cruciate retaining design for total knee arthroplasty-an in vivo randomized controlled study of gait using dynamic radiostereometry.

PURPOSE: New total knee arthroplasty implant designs attempt to normalize kinematics patterns that may improve functional performance and patient satisfaction. It was hypothesized that a more medial congruent (MC) anatomic bearing design (1) influences the tibiofemoral kinematics and (2) enhances articular congruency compared to a standard symmetrical cruciate retaining (CR) bearing design. METHODS: In this double-blinded randomized study, 66 patients with knee osteoarthritis were randomly included in two groups: MC (n = 31) and CR (n = 33). Clinical characteristics such as knee ligament lesions and knee osteoarthritis scores were graded on preoperative magnetic resonance imaging and radiography. At the 1-year follow-up, dynamic radiostereometric analysis was used to assess tibiofemoral joint kinematics and articulation congruency. Patient-reported outcome measures, Oxford Knee Score, the Forgotten Joint Score, and the Knee Osteoarthritis Outcome Score, were assessed preoperatively and at the 1-year follow-up. RESULTS: Compared to the CR bearing, the MC bearing displayed an offset with approximately 3 mm greater anterior tibial drawer (p < 0.001) during the entire motion, and up to approximately 3.5 degrees more tibial external rotation (p = 0.004) from mid-swing to the end of the gait cycle at the 1-year follow-up. Furthermore, the congruency area in the joint articulation was larger during approximately 80% of the gait cycle for the MC bearing compared to the CR. The patient-reported outcome measures improved (p < 0.001), but there were no differences between groups. In addition, there were no differences in clinical characteristics and there were no knee revisions or recognized deep infections during follow-up. CONCLUSION: The study demonstrates that the MC-bearing design changes tibiofemoral kinematics and increases the area of congruency towards more native knee kinematics than the CR bearing. In perspective this may contribute to a more stabilized knee motion, restoring the patient's confidence in knee function during daily activities.

Early Survivorship of Uncemented Total Knee Arthroplasty Varies by Age and Sex Based on Data From the Michigan Arthroplasty Registry Collaborative Quality Initiative.

BACKGROUND: Outcome data for newer uncemented total knee arthroplasty (TKA) designs has been mixed. Registry studies showed worse survivorship, but clinical trials have not demonstrated differences compared to cemented designs. There has been renewed interest in uncemented TKA with modern designs and improved technology. The utilizations of uncemented knees in Michigan, 2-year outcomes, and the effects of age and sex were evaluated. METHODS: A statewide database from 2017 through 2019 was analyzed for incidence, distribution, and early survivorship of cemented versus uncemented TKAs. There was 2-year minimum follow-up. Kaplan-Meier survival analysis was used to generate time to first revision cumulative percent revision curves. The impacts of age and sex were examined. RESULTS: Use of uncemented TKAs increased from 7.0 to 11.3%. Uncemented TKAs were more commonly men, younger, heavier, American Society of Anesthesiologists score > 2, and opioid users (P < .05). At 2 years, overall cumulative percent revision was higher in uncemented (2.44% [2.00, 2.99]) versus cemented (1.76% [1.64, 1.89]), particularly in women uncemented (2.41 [1.87, 3.12]) versus cemented (1.64 [1.50, 1.80]). Revision rates were greater with uncemented women >70 years (1.2% 1 year, 1.02% 2 years) versus < 70 years (0.56%, 0.53%), notably uncemented were inferior in both groups (P < .05). Men, regardless of age, had similar survivorships with both cemented and uncemented designs. CONCLUSION: The use of an uncemented TKA had an increased risk of early revision compared to cemented. This finding, however, was only apparent in women, especially those >70 years old. Surgeons should consider cement fixation in women >70 years.

Femur-First Technique for Mobile Bearing Unicompartmental Knee Arthroplasty Results in Decreased Implant Variability and Early Improvements in Function and Survivorship.

BACKGROUND: Higher failure rates of unicompartmental knee arthroplasty (UKA) are seen with lower surgical volume. Surgical techniques that introduce less variability improving implant positioning may lead to improved survivorship. A femur-first (FF) technique has been described, but survivorship data compared to traditional tibia-first (TF) technique are under-reported. We report the results of mobile-bearing UKA using the FF technique compared to the TF technique with emphasis on implant position and survivorship. METHODS: A total of 430 UKAs were performed by a single surgeon between 2007 and 2020. After 2012, there were 141 consecutive UKAs performed with the FF technique which were compared with 147 consecutive UKAs prior. Mean follow-up was 6 years (range, 2 to 13 years), average age was 63 years (range, 23 to 92 years), and there were 132 women. Postoperative radiographs were reviewed to determine implant positioning. Survivorship analyses were performed using Kaplan-Meier curves. RESULTS: The FF resulted in significantly thinner polyethylene (3.4 ± 0.7 mm versus 3.7 ± 0.9 mm) (P = .002) and 4 mm or less bearing thickness in 94% of cases. At 5 years, there was an early trend toward improved survivorship free from component revision (98% for the FF group and 94% for the TF [P = .35]). The FF cohort had higher Knee Society Functional scores at final follow-up (P < .001). CONCLUSION: Compared to traditional TF technique, the FF was more bone-preserving and improved radiographic positioning. The FF technique is an alternative method for mobile-bearing UKA and was associated with an improvement in implant survivorship and function.

Difference Between Screw Cement Filling and Adequate Osteotomy With Thick Liner for Primary Total Knee Arthroplasty in Patients With Rand IIb Tibial Defects.

BACKGROUND: The effectiveness of 2 treatment options, screw-cement fill, and adequate osteotomy with a thick liner, in treating patients with Rand IIb tibial defects (tibial plateau defects to a depth of 5 to 10 millimeters) in primary total knee arthroplasty (TKA) has not yet been demonstrated. Therefore, we performed a retrospective study to evaluate the differences between these 2 treatments. METHODS: We retrospectively analyzed patients who underwent primary TKA for Rand IIb tibial plateau defects from 2015 to 2020 from a department database. Patients were categorized into the screw-cement and thick liner groups based on the different options used to repair tibial defects. We evaluated Knee Society Score, range of motion (ROM), Insall-Salvati index (ISI), and Forgotten Joint Score (FJS) in both groups. We also compared differences in prosthesis survival, stiffness, myasthenia, and joint clicking between the 2 groups at mean 2 years postoperatively (range, 2 to 2.3). A power analysis was performed on the number of cases in the cohort. RESULTS: Postoperative femur-tibia mechanical axis (FTMA) correction was significantly higher in the screw-cement group than in the thick-liner group: 18.8 (±5.6°) versus 15.4 (±5.9°) (P < .01); At mean 2 years after surgery, the American Knee Society Functional Score improvement values were higher in the thick-liner group than in the screw-cement group: 36.3 (±12.4) versus 42.4 (±16.4) (P = .05). Postoperative ISI scores were 0.95 (±0.12) points in the screw-cement group and 0.89 (±0.13) points in the-thick liner group (P = .03). There were no statistically significant differences in the Knee Society Clinical Score, ROM, FJS, stiffness, myasthenia, joint clicking, and revision rate. CONCLUSION: The results of this study showed no significant difference in clinical outcomes between the 2 reconstruction strategies of the screw cement fill technique and the adequate osteotomy and thick liner technique for Rand IIb tibial plateau defects. However, in patients who have FTMA deformities greater than 20° or in younger patients who need to preserve bone volume, we recommend the screw cement filling technique to ensure stable postoperative results and to prepare these patients for possible later surgery.

Cementless and Cemented Dual-Pivot Total Knee Arthroplasty: A Matched Comparison With a Minimum Two-Year Follow-Up.

BACKGROUND: With the use of newer biomaterials, many authors have reported similar results between cementless and cemented total knee arthroplasty (TKA). The purpose of this study was to compare the early clinical and radiographic outcomes of cementless and cemented TKA using the same dual-pivot articulation. METHODS: A consecutive series of 806 TKAs were implanted by a single surgeon using the same dual-pivot articulation. There were 634 TKAs (79%) cemented and 172 (21%) uncemented. One patient in the cementless group was lost before two years. The remaining 171 cementless TKAs were matched 1:1 with cemented TKAs with respect to age, sex, and body mass index. All patients were followed for a minimum of two years (range, 24-66 months) using the Knee Injury and Osteoarthritis Outcome Score for Joint Replacement , and Knee Society clinical and radiographic evaluation. The average follow-up was 3.8 years (range, 24-66 months) in the cemented group and 3.4 years (range, 24-56 months) in the cementless group. RESULTS: At final follow-up, the average Knee Injury and Osteoarthritis Outcome Score for Joint Replacement was higher in the cementless group (86 points (range, 64-100) versus 80 points (range, 57-100). Postoperative Knee Society scores (including pain and function) were similar. There was one deep infection (cemented TKA). The manipulation rate was 1.2% in the cementless group and 2.4% in the cemented TKA group. Excluding infection, two knees (1.2%) were revised in each group. No cases of femoral or tibial component loosening were identified. CONCLUSION: Patients implanted with either a cemented or cementless TKA using the same conforming dual-pivot articulation design had similar early outcomes and functional improvements. The type of fixation did not appear to influence the early clinical results.

Comparison of cementless twin-peg, cemented twin-peg and cemented single-peg femoral component migration after medial unicompartmental knee replacement: a 5-year randomized RSA study.

BACKGROUND: The component design and fixation method of joint arthroplasty may affect component migration and survival. The aim of this study was to compare fixation of cementless twin-peg (CLTP), cemented twin-peg (CTP) and cemented single-peg (CSP) femoral components of medial unicompartmental knee replacement (UKR). METHODS: Eighty patients (mean age = 63 years, 48 males) with medial knee osteoarthritis were randomized in three ways to CLTP (n = 25), CTP (n = 26) or CSP (n = 29) femoral UKR components. The patients were followed 5 years postoperatively with RSA, bone mineral density (BMD), PROMs and radiological evaluation of radiolucent lines (RLL), femoral component flexion angle and complications. RESULTS: At the 5-year follow-up, femoral component total translation was comparable between the three groups (p = 0.60). Femoral component internal rotation was 0.50° (95% CI 0.3; 0.69) for the CLTP group, 0.58° (95% CI 0.38; 0.77) for the CTP group and 0.25° (95% CI 0.07; 0.43) for the CSP group (p = 0.01). BMD decreased peri-prosthetically (range - 11.5%; - 14.0%) until 6-month follow-up and increased toward the 5-year follow-up (range - 3.6%; - 5.8%). BMD change did not correlate with component migration. Lower flexion angle was correlated with higher 5-year subsidence, total translation, varus rotation and maximum total point motion (p = 0.01). Two patients (1 CLTP, 1 CTP) had RLL in the posterior zone. There were two revisions. CONCLUSION: At 5-year follow-up, fixation of UKA femoral components with twin-peg was not superior to the single-peg design. Cementless and cemented twin-peg femoral components had similar fixation. A lower flexion angle was correlated with higher component migration.

[Effect of prosthetic joint line installation height errors on insert wear in unicompartmental knee arthroplasty].

The clinical performance and failure issues are significantly influenced by prosthetic malposition in unicompartmental knee arthroplasty (UKA). Uncertainty exists about the impact of the prosthetic joint line height in UKA on tibial insert wear. In this study, we combined the UKA musculoskeletal multibody dynamics model, finite element model and wear model to investigate the effects of seven joint line height cases of fixed UKA implant on postoperative insert contact mechanics, cumulative sliding distance, linear wear depth and volumetric wear. As the elevation of the joint line height in UKA, the medial contact force and the joint anterior-posterior translation during swing phase were increased, and further the maximum von Mises stress, contact stress, linear wear depth, cumulative sliding distance, and the volumetric wear also were increased. Furthermore, the wear area of the insert gradually shifted from the middle region to the rear. Compared to 0 mm joint line height, the maximum linear wear depth and volumetric wear were decreased by 7.9% and 6.8% at -2 mm joint line height, and by 23.7% and 20.6% at -6 mm joint line height, the maximum linear wear depth and volumetric wear increased by 10.7% and 5.9% at +2 mm joint line height, and by 24.1% and 35.7% at +6 mm joint line height, respectively. UKA prosthetic joint line installation errors can significantly affect the wear life of the polyethylene inserted articular surfaces. Therefore, it is conservatively recommended that clinicians limit intraoperative UKA joint line height errors to -2-+2 mm.

Similar clinical and radiographic outcomes after two different hypoallergenic medial unicompartmental knee in patients with metal allergy.

BACKGROUND: The purpose in the present study was to compare clinical and radiological outcomes of patients who had undergone a mobile-bearing unicompartmental knee arthroplasty (UKA) with either titanium niobium nitride (TiNbN) alloy implants or with fixed-bearing oxidized zirconium alloy implants. METHODS: The records of two consecutive cohorts for a total of 86 hypoallergenic implants were prospectively analyzed. The first cohort consisted of 49 consecutive implantations of the hypoallergenic UKA Journey Uni Oxinium (Ox Group), while the second consisted of 37 consecutive series of UKA Oxford (TiNbN Group). All patients were evaluated by two independent surgeons who were not involved in the index surgery. The clinical evaluation consisted of evaluating each patient's Oxford Knee Score and Knee Society Score day before surgery (T0), and with two consecutive follow-ups at T1 (minimum follow-up 9 months) and T2 (minimum follow-up 24 months). RESULTS: The two groups were homogeneous in all preoperative values, except Body Mass Index (BMI) and duration of final follow-up [both statistically higher (p < 0.05) in the TiNbN group]. Both groups showed a clinically significant improvement for all scores at final follow-up (p < 0.05). The only differences between the two groups involved a higher pre-operative Oxford Score in TiNbN group (p = 0.031), and different tibial and femoral angles at the final follow-up. CONCLUSIONS: Both TiNbN and Oxinium UKA procedures enabled patients from good to excellent clinical and radiographic outcomes after the final follow-up, regardless of the age, gender, BMI bearing type, and implant size. LEVEL OF EVIDENCE: LEVEL II: Comparative study.

Arthroplasty Surgeons Differ in Their Intraoperative Soft Tissue Assessments: A Study in Human Cadavers to Quantify Surgical Decision-making in TKA.

BACKGROUND: In TKA, soft tissue balancing is assessed through manual intraoperative trialing. This assessment is a physical examination via manually applied forces at the ankle, generating varus and valgus moments at the knee while the surgeon visualizes the lateral and medial gaps at the joint line. Based on this examination, important surgical decisions are made that influence knee stability, such as choosing the polyethylene insert thickness. Yet, the applied forces and the assessed gaps in this examination represent a qualitative art that relies on each surgeon's intuition, experience, and training. Therefore, the extent of variation among surgeons in conducting this exam, in terms of applied loads and assessed gaps, is unknown. Moreover, whether variability in the applied loads yields different surgical decisions, such as choice of insert thickness, is also unclear. Thus, surgeons and developers have no basis for deciding to what extent the applied loads need to be standardized and controlled during a knee balance exam in TKA. QUESTIONS/PURPOSES: (1) Do the applied moments in soft tissue assessment differ among surgeons? (2) Do the assessed gaps in soft tissue assessment differ among surgeons? (3) Is the choice of insert thickness associated with the applied moments? METHODS: Seven independent human cadaveric nonarthritic lower extremities from pelvis to toe were acquired (including five females and two males with a mean age of 73 ± 7 years and a mean BMI of 25.8 ± 3.8 kg/m 2 ). Posterior cruciate ligament substituting (posterior stabilized) TKA was performed only on the right knees. Five fellowship-trained knee surgeons (with 24, 15, 15, 7, and 6 years of clinical experience) and one chief orthopaedic resident independently examined soft tissue balance in each knee in extension (0° of flexion), midflexion (30° of flexion), and flexion (90° of flexion) and selected a polyethylene insert based on their assessment. Pliable force sensors were wrapped around the leg to measure the loads applied by each surgeon. A three-dimensional (3D) motion capture system was used to measure knee kinematics and a dynamic analysis software was used to estimate the medial and lateral gaps. We assessed (1) whether surgeons applied different moments by comparing the mean applied moment by surgeons in extension, midflexion, and flexion using repeated measures (RM)-ANOVA (p < 0.05 was assumed significantly different); (2) whether surgeons assessed different gaps by comparing the mean medial and lateral gaps in extension, midflexion, and flexion using RM-ANOVA (p < 0.05 was assumed significantly different); and (3) whether the applied moments in extension, midflexion, and flexion were associated with the insert thickness choice using a generalized estimating equation (p < 0.05 was assumed a significant association). RESULTS: The applied moments differed among surgeons, with the largest mean differences occurring in varus in midflexion (16.5 Nm; p = 0.02) and flexion (7.9 Nm; p < 0.001). The measured gaps differed among surgeons at all flexion angles, with the largest mean difference occurring in flexion (1.1 ± 0.4 mm; p < 0.001). In all knees except one, the choice of insert thickness varied by l mm among surgeons. The choice of insert thickness was weakly associated with the applied moments in varus (ß = -0.06 ± 0.02 [95% confidence interval -0.11 to -0.01]; p = 0.03) and valgus (ß = -0.09 ± 0.03 [95% CI -0.18 to -0.01]; p= 0.03) in extension and in varus in flexion (ß = -0.11 ± 0.04 [95% CI -0.22 to 0.00]; p = 0.04). To put our findings in context, the greatest regression coefficient (ß = -0.11) indicates that for every 9-Nm increase in the applied varus moment (that is, 22 N of force applied to the foot assuming a shank length of 0.4 m), the choice of insert thickness decreased by 1 mm. CONCLUSION: In TKA soft tissue assessment in a human cadaver model, five surgeons and one chief resident applied different moments in midflexion and flexion and targeted different gaps in extension, midflexion, and flexion. A weak association between the applied moments in extension and flexion and the insert choice was observed. Our results indicate that in the manual assessment of soft tissue, changes in the applied moments of 9 and 11 Nm (22 to 27 N on the surgeons' hands) in flexion and extension, respectively, yielded at least a 1-mm change in choice of insert thickness. The choice of insert thickness may be more sensitive to the applied moments in in vivo surgery because the surgeon is allowed a greater array of choices beyond insert thickness. CLINICAL RELEVANCE: Among five arthroplasty surgeons with different levels of experience and a chief resident, subjective soft tissue assessment yielded 1 to 2 mm of variation in their choice of insert thickness. Therefore, developers of tools to standardize soft tissue assessment in TKA should consider controlling the force applied by the surgeon to better control for variations in insert selection.

Difference between medial and lateral tibia plateau in the coronal plane: importance of preoperative evaluation for medial unicompartmental knee arthroplasty.

BACKGROUND: Setting bone cutting levels for different joint line orientations of the medial and lateral tibia plateaus in individual patients is not clear. We aimed to evaluate the difference between joint line orientation of the medial and lateral tibia plateaus relative to the horizontal line of mechanical axis of tibia as tibial plateau difference (TPD) for an optimal tibial bone cut in medial unicompartmental knee arthroplasty (UKA) and determine which factors could influence TPD. We aimed to investigate the effect of preoperative TPD on polyethylene liner size in medial UKA. METHODS: TPD in the coronal plane were measured in 181 female patients (181 knees). To determine the morphology of proximal tibia according to the severity of osteoarthritis, the patients were classified into three groups based on diagnosis and treatment: 80 who underwent robot-assisted medial UKA, 45 who underwent total knee arthroplasty (TKA), and 56 with early-stage osteoarthritis (OA) who had conservative management. Also, we divided the medial UKA group into two groups according to TPD (greater than or less than 5 mm) and compared polyethylene liner sizes. RESULTS: No significant difference was observed in TPD (p = 0.662), difference between the medial and lateral femoral condyle levels (p = 0.54), medial proximal tibial angle (p = 0.169), or posterior tibial slope (p = 0.466) among the three groups. Increased TPD was significantly associated with increased mechanical femorotibial angle(mFTA) (p < 0.01). The medial UKA group was divided into two groups according to TPD greater or less than 5 mm. Thicker polyethylene liners were used for groups with TPD greater than 5 mm (8.5 ± 0.7 mm versus 8.2 ± 0.3 mm, p = 0.01). Additionally, the proportion of patients using the thinnest polyethylene (8 mm) in each TPD group (greater or less than 5 mm) was higher in patients with TPD less than 5 mm (82.4% versus 58.7%, p = 0.038). CONCLUSIONS: Preoperative measurement of TPD is important to help surgeons predict the most appropriate bone cutting level in the coronal plane in primary medial UKA. Tibial bone resection would be likely to be thicker than needed in patients with increased TPD in medial UKA.

Cementless unicompartmental knee arthroplasty results in higher pain levels compared to the cemented technique: a prospective register study.

PURPOSE: In recent years, the preferred fixation method for unicompartmental knee arthroplasty (UKA) has changed from cemented to cementless. The aim of this study was to compare patient-reported outcome measures (PROMs) from the cemented versus cementless techniques two- and twelve-months post-operation. METHODS: From 2015 to 2019, 187 cemented and 261 cementless UKAs were included based on an institutional registry. The Oxford Unicompartmental Knee System™ (Zimmer Biomet, Bridgend, United Kingdom) was used for all patients. Three experienced surgeons performed all procedures. Data were collected pre- and peroperatively, and at two- and twelve-months postoperatively. PROMs included pain (evaluated on a numeric rating scale [NRS] during activity and at rest), and knee function (evaluated with the disease-specific short form of the Knee injury and Osteoarthritis Outcome Score [KOOS-PS]). Patients also rated postoperative joint function (better, unchanged, uncertain or worse) and were asked, "based on your experience to date, would you go through the surgery again?". Duration of surgery was noted and revisions during the first post-operative year were evaluated. RESULTS: The cemented group reported significantly lower activity-related pain at both two- and twelve-month follow-up. This was also the case for pain at rest at twelve-month follow-up, and KOOS-PS at two-month follow-up. Duration of surgery (adjusted for surgeon differences) was eight minutes less on average with the cementless technique. Eleven prosthetic joint infections (PJIs) were found following the cementless fixation technique compared to three using the cemented implant. CONCLUSION: UKA cases with cemented implants had lower pain scores during activity two and twelve months after surgery compared with those who had cementless implants. Differences in favor of the cemented group were also found for pain at rest one year after surgery and for KOOS-PS two months after. Surgery was significantly shorter in duration in the cementless group, but a relatively high number of PJIs were found in that same group. LEVEL OF EVIDENCE: Level II.

Implantation of the Femoral Component Relative to the Tibial Component in Medial Unicompartmental Knee Arthroplasty: A Clinical, Radiological, and Biomechanical Study.

BACKGROUND: Unicompartmental knee arthroplasty (UKA) is a procedure with low morbidity and fast recovery. Anatomic implants or robotic-assisted UKA has been proposed to improve outcomes with precise positioning. Femoral component position (FCP) relative to the tibial insert could be a factor influencing the contact stresses. We aimed to evaluate the effect of the FCP relative to the tibial insert on clinical outcomes and stress distribution after medial UKA. METHODS: Sixty-two medial fixed-bearing UKAs were evaluated at a minimum two-year follow-up using the Knee Society Score. Postoperative radiological evaluation performed on frontal X-rays classified the FCP relative to the tibial insert into the following: group M (medial), group C (central), and group L (lateral). A finite element model was developed to evaluate the biomechanical effects of the FCP relative to the tibial component. RESULTS: The postoperative radiological evaluation showed 9 cases in group M, 46 cases in group C, and 7 cases in group L. The maximum knee flexion angle and the 2-year postoperative "symptom" and "patient satisfaction" scores of the Knee Society Score were significantly higher in group C. Compared with central positioning, a shift along the mediolateral axis leads to a displacement of the contact pressure center. CONCLUSION: The FCP relative to the tibial insert may increase patient outcomes at a minimum follow-up of two years after fixed-bearing medial UKA. Accordance between FCP and contact stresses on the polyethylene insert could be a contributing factor of long-term survival of UKA.

Causes of knee pain evaluated by arthroscopy after knee arthroplasty: a case series.

BACKGROUND: The origin of persistent pain and joint limitation after knee arthroplasty are controversial and difficult to diagnose. Knee arthroscopy is indicated when the results of routine evaluation tests are not clear. The purpose of this study was to determine through arthroscopy the cause of post-knee-arthroplasty pain symptoms in patients without a prior diagnosis of cause of pain. METHODS: This prospective case series study described the outcomes of 34 patients (35 knees) with pain and limited function in the arthroplastic joint, who underwent diagnostic and therapeutic arthroscopy. Patients were clinically evaluated using range-of-motion tests and the Lysholm, Hospital for Special Surgery (HSS) and Knee Society Score (KSS) scales. RESULTS: The procedure found cyclops in 17 knees, synovitis in 9 knees, arthrofibrosis in 6 knees, polyethylene wear with debris in two knees, and polyethylene bouncing in one knee with unicompartmental arthroplasty with a mobile polyethylene platform. It was effective for the relief of pain symptoms, with excellent or good outcomes in 80% of cases; there was a poor outcome in 11.43%, which maintained the presentation of pain and underwent revision arthroplasty, and, in 8.57%, did not undergo another surgery despite symptom persistence. CONCLUSIONS: Post-arthroplasty knee arthroscopy seems beneficial in patients with pain and without a pre-established diagnosis and who had already undergone conservative treatment unsuccessfully.