Adsorptive stripping voltammetric determination of imipramine, trimipramine and desipramine employing titanium dioxide nanoparticles and an Amberlite XAD-2 modified glassy carbon paste electrode.

An Amberlite XAD-2 (XAD2) and titanium dioxide nanoparticles (TNPs) modified glassy carbon paste electrode (XAD2-TNP-GCPE) was developed for the determination of imipramine (IMI), trimipramine (TRI) and desipramine (DES). The electrochemical behavior of these molecules was investigated employing cyclic voltammetry (CV), chronocoulometry (CC), electrochemical impedance spectroscopy (EIS) and adsorptive stripping differential pulse voltammetry (AdSDPV). After optimization of analytical conditions using a XAD2-TNP-GCPE electrode at pH 6.0 phosphate buffer (0.1 M), the peak currents were found to vary linearly with its concentration in the range of 1.30 × 10(-9) to 6.23 × 10(-6) M for IMI, 1.16 × 10(-9) to 6.87 × 10(-6) M for TRI and 1.43 × 10(-9) to 5.68 × 10(-6) M for DES. The detection limits (S/N = 3) of 3.93 × 10(-10), 3.51 × 10(-10) and 4.35 × 10(-10) M were obtained for IMI, TRI and DES respectively using AdSDPV. The prepared modified electrode showed several advantages such as a simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. The proposed method was employed for the determination of IMI, TRI and DES in pharmaceutical formulations, blood serum and urine samples.

Electromembrane extraction combined with cyclodextrin-modified capillary electrophoresis for the quantification of trimipramine enantiomers.

A sensitive, simple and reproducible method was developed for preconcentration and determination of trimipramine (TPM) enantiomers in biological samples using electromembrane extraction combined with cyclodextrin-modified capillary electrophoresis (CE). During the extraction, TPM enantiomers migrated from a 5 mL sample solution through a thin layer of 2-nitrophenyl octyl ether NPOE immobilized in the pores of a hollow fiber, and into a 20 µL acidic aqueous acceptor phase presented inside the lumen of the fiber. A Box-Behnken design and the response surface methodology (RSM) were used for the optimization of different variables on extraction efficiency. Optimized extraction conditions were: NPOE as supported liquid membrane, inter-electrode distance of 5 mm, stirring rate of 1000 rpm, 51 V potential difference, 34 min as the extraction time, acceptor phase pH 1.0 and donor phase pH 4.5. Then, the extract was analyzed using optimized cyclodextrin (CD)-modified CE method for the separation of TPM enantiomers. Best results were achieved using 100 mM phosphate running buffer (pH 2.0) containing 10 mM α-CD as the chiral selector, applied voltage of 18 kV and 20°C. The range of quantitation for both enantiomers was 20-500 ng/mL. The method was very reproducible so that intra- and interday RSDs (n=6) were <6%. The limits of quantitation and detection for both enantiomers were 20 and 7 ng/mL, respectively. Finally, this method was successfully applied to determine the concentration of TPM enantiomers in plasma and urine samples without any pre-treatment.

A new carbon paste electrode modified with MWCNTs and nano-structured molecularly imprinted polymer for ultratrace determination of trimipramine: The crucial effect of electrode components mixing on its performance.

A novel carbon nanocomposite paste electrode was prepared and used as a voltammetric sensor for ultratrace determination of trimipramine (TRI) which currently used for the treatment of psychiatric disorders. For this aim, nanoparticles of molecularly imprinted polymer (MIP), synthesized by precipitation polymerization method, and multi-walled carbon nanotubes (MWCNTs) were embedded in a nanocomposite paste electrode. The nanocomposite mixing style demonstrated a significant influence on the final electrode performance. The sensor exhibited linear response range of 1.0 × 10-10-2.5 × 10-8 mol L-1 and very high sensitivity of 2131 µA µâ€¯mol L-1. The lower detection limit of the sensor was calculated to be 4.5 × 10-11 mol L-1 (S/N = 3). This sensor was applied successfully for highly selective determination of TRI in pharmaceutical formulations, urine and serum samples without applying any sample pretreatment.