Self-oscillating polymeric refrigerator with high energy efficiency.

Electrocaloric1,2 and electrostrictive3,4 effects concurrently exist in dielectric materials. Combining these two effects could achieve the lightweight, compact localized thermal management that is promised by electrocaloric refrigeration5. Despite a handful of numerical models and schematic presentations6,7, current electrocaloric refrigerators still rely on external accessories to drive the working bodies8-10 and hence result in a low device-level cooling power density and coefficient of performance (COP). Here we report an electrocaloric thin-film device that uses the electro-thermomechanical synergy provided by polymeric ferroelectrics. Under one-time a.c. electric stimulation, the device is thermally and mechanically cycled by the working body itself, resulting in an external-driver-free, self-cycling, soft refrigerator. The prototype offers a directly measured cooling power density of 6.5 W g-1 and a peak COP exceeding 58 under a zero temperature span. Being merely a 30-µm-thick polymer film, the device achieved a COP close to 24 under a 4 K temperature span in an open ambient environment (32% thermodynamic efficiency). Compared with passive cooling, the thin-film refrigerator could immediately induce an additional 17.5 K temperature drop against an electronic chip. The soft, polymeric refrigerator can sense, actuate and pump heat to provide automatic localized thermal management.

Novel 3D textile structures and geometries for electrofluidics.

The integration of microfluidics with electric field control, commonly referred to as electrofluidics, has led to new opportunities for biomedical analysis. The requirement for closed microcapillary channels in microfluidics, typically formed via complex microlithographic fabrication approaches, limits the direct accessibility to the separation processes during conventional electrofluidic devices. Textile structures provide an alternative and low-cost approach to overcome these limitations via providing open and surface-accessible capillary channels. Herein, we investigate the potential of different 3D textile structures for electrofluidics. In this study, 12 polyester yarns were braided around nylon monofilament cores of different diameters to produce functional 3D core-shell textile structures. Capillary electrophoresis performances of these 3D core-shell textile structures both before and after removing the nylon core were evaluated in terms of mobility and bandwidth of a fluorescence marker compound. It was shown that the fibre arrangement and density govern the inherent capillary formation within these textile structures which also impacts upon the solute analyte mobility and separation bandwidth during electrophoretic studies. Core-shell textile structures with a 0.47 mm nylon core exhibited the highest fluorescein mobility and presented a narrower separation bandwidth. This optimal textile structure was readily converted to different geometries via a simple heat-setting of the central nylon core. This approach can be used to fabricate an array of miniaturized devices that possess many of the basic functionalities required in electrofluidics while maintaining open surface access that is otherwise impractical in classical approaches.

Biocompatible Janus microparticle synthesis in a microfluidic device.

Janus particles are popular in recent years due to their anisotropic physical and chemical properties. Even though there are several established synthesis methods for Janus particles, microfluidics-based methods are convenient and reliable due to low reagent consumption, monodispersity of the resultant particles and efficient control over reaction conditions. In this work a simple droplet-based microfluidic technique is utilized to synthesize magnetically anisotropic TiO2-Fe2O3 Janus microparticles. Two droplets containing reagents for Janus particle were merged by using an asymmetric device such that the resulting droplet contained the constituents within its two hemispheres distinct from each other. The synthesized Janus particles were observed under the optical microscope and the scanning electron microscope. Moreover, a detailed in vitro characterization of these particles was completed, and it was shown that these particles have a potential use for biomedical applications.

Nebulization and In Vitro Upper Airway Deposition of Liposomal Carrier Systems.

Liposomal carrier systems have emerged as a promising technology for pulmonary drug delivery. This study focuses on two selected liposomal systems, namely, dipalmitoylphosphatidylcholine stabilized by phosphatidic acid and cholesterol (DPPC-PA-Chol) and dipalmitoylphosphatidylcholine stabilized by polyethylene glycol and cholesterol (DPPC-PEG-Chol). First, the research investigates the stability of these liposomal systems during the atomization process using different kinds of nebulizers (air-jet, vibrating mesh, and ultrasonic). The study further explores the aerodynamic particle size distribution of the aerosol generated by the nebulizers. The nebulizer that demonstrated optimal stability and particle size was selected for more detailed investigation, including Andersen cascade impactor measurements, an assessment of the influence of flow rate and breathing profiles on aerosol particle size, and an in vitro deposition study on a realistic replica of the upper airways. The most suitable combination of a nebulizer and liposomal system was DPPC-PA-Chol nebulized by a Pari LC Sprint Star in terms of stability and particle size. The influence of the inspiration flow rate on the particle size was not very strong but was not negligible either (decrease of Dv50 by 1.34 µm with the flow rate increase from 8 to 60 L/min). A similar effect was observed for realistic transient inhalation. According to the in vitro deposition measurement, approximately 90% and 70% of the aerosol penetrated downstream of the trachea using the stationary flow rate and the realistic breathing profile, respectively. These data provide an image of the potential applicability of liposomal carrier systems for nebulizer therapy. Regional lung drug deposition is patient-specific; therefore, deposition results might vary for different airway geometries. However, deposition measurement with realistic boundary conditions (airway geometry, breathing profile) brings a more realistic image of the drug delivery by the selected technology. Our results show how much data from cascade impactor testing or estimates from the fine fraction concept differ from those of a more realistic case.

Comparison of Clinical Effectiveness and Safety of Drug-Coated Balloons versus Percutaneous Transluminal Angioplasty in Arteriovenous Fistulae: A Review of Systematic Reviews and Updated Meta-Analysis.

PURPOSE: To evaluate the clinical effectiveness and safety of drug-coated balloons (DCBs) compared with those of percutaneous transluminal angioplasty (PTA) for arteriovenous fistula (AVF) stenosis via a review of systematic reviews (SRs) and an update of the current meta-analysis. MATERIALS AND METHODS: Literature was searched to retrieve SRs comparing DCBs and PTA for AVFs. A narrative review of SRs and pooled analysis were performed. RESULTS: Eleven SRs were included. DCBs demonstrated favorable outcomes at 6 and 12 months compared with PTA, with improved patency in 7 SRs and a trend toward favorable outcomes without statistical significance in 3 SRs. Target lesion revascularization (TLR) was reported in 3 SRs; 2 reviews reported a significantly lower incidence in the DCB group than in the PTA group, whereas 1 review reported no significant differences at 12 months. Four studies reporting all-cause mortality revealed no significant difference between the 2 treatments. In the updated meta-analysis including 23 studies, DCBs demonstrated improved primary patency at 6 months (risk ratio [RR], 1.27; 95% CI, 1.07-1.50) and 12 months (RR, 1.36; 95% CI, 1.19-1.55) and were associated with a lower incidence of TLR at 6 months (RR, 0.54; 95% CI, 0.41-0.73) and 12 months (RR, 0.78; 95% CI, 0.62-0.99). There was no difference in mortality between the 2 groups for 24 months. CONCLUSIONS: A review of SRs and meta-analysis update revealed the consistent benefits of DCBs over PTA in treating AVFs in terms of primary patency and TLR. Compared with PTA, DCBs do not increase mortality risk.

Comparison of Outcomes of Drug-Coated Balloons versus Plain Balloons in Secondary Interventions on Percutaneous Arteriovenous Fistulae.

PURPOSE: To compare patency and reintervention outcomes after either plain old balloon angioplasty (POBA) or drug-coated balloon angioplasty (DCBA) for venous stenoses after percutaneous arteriovenous fistula (pAVF) creation. MATERIALS AND METHODS: One-hundred ninety-five pAVFs were successfully created during the study period, 141 using Ellipsys and 54 using Wavelinq. After pAVF creation, 95 patients (48.7%) required secondary percutaneous transluminal angioplasty (PTA) with either POBA (n = 55, 58%) or DCBA (n = 40, 42.1%). The most common site for PTA was the juxta-anastomotic segment (75.5%; 74/98). Univariate and multivariate Cox regression analyses were used to compare target lesion primary patency, access circuit primary patency, secondary patency, and reintervention rates in the POBA and DCBA cohorts. RESULTS: Thirty-four of 55 (62%) patients in the POBA cohort and 14 of 40 (35%) patients in the DCBA cohort required reinterventions for pAVF restenosis. Mean number of follow-up days among patients treated with POBA was 1,030.4 (SD ± 342.9) and among those treated with DCBA was 744.4 (SD ± 403.5). The use of POBA compared with DCBA was not associated with target lesion and access circuit primary patency loss in multivariate analysis (hazard ratio [HR], 1.81; 95% CI, 0.93-3.51; P = .080; and HR, 1.77; 95% CI, 0.73-4.28; P = .210, respectively). However, time from fistula creation to the first PTA (days) was statistically significantly associated with both outcomes (HR, 0.997; 95% CI, 0.994-0.999; P = .009; and HR, 0.997; 95% CI, 0.992-0.999; P = .021, respectively). There were no major adverse events. CONCLUSIONS: In this retrospective single-center analysis of pAVFs, considerably more patients who underwent PTA with POBA after pAVF creation required reinterventions compared with PTA using DCBA, although the follow-up time of POBA was longer. In multivariate analysis, no differences were noted in the hazard of patency loss between POBA and DCBA.

Efficacy and safety of drug-coated balloons in chronic total coronary occlusion recanalization: a systematic review and meta-analysis.

BACKGROUND: With advancements in chronic total coronary occlusion (CTO) recanalization techniques and concepts, the success rate of recanalization has been steadily increasing. However, the current data are too limited to draw any reliable conclusions about the efficacy and safety of drug-coated balloons (DCBs) in CTO percutaneous coronary intervention (PCI). Herein, we conducted a meta-analysis to confirm the efficacy of DCB in CTO PCI. METHODS: We systematically searched PubMed, Web of Science and Embase from inception to July 25, 2023. The primary outcome was major advent cardiovascular events (MACE), including cardiac death, nonfatal myocardial infarction (MI), target lesion revascularization (TLR), and target vessel revascularization (TVR). The follow-up angiographic endpoints were late lumen enlargement (LLE), reocclusion and restenosis. RESULTS: Five studies with a total of 511 patients were included in the meta-analysis. Across studies, patients were predominantly male (72.9-85.7%) and over fifty years old. The summary estimate rate of MACE was 13.0% (95% CI 10.1%-15.9%, I2 = 0%, p = 0.428). The summary estimate rates of cardiac death and MI were 2.2% (95% CI 0.7%-3.7%, I2 = 0%, p = 0.873) and 1.2% (95% CI -0.2-2.6%, I2 = 13.7%, p = 0.314), respectively. Finally, the pooled incidences of TLR and TVR were 10.1% (95% CI 5.7%-14.5%, I2 = 51.7%, p = 0.082) and 7.1% (95% CI 3.0%-11.2%, I2 = 57.6%, p = 0.070), respectively. Finally, the summary estimate rates of LLE, reocclusion and restenosis were 59.4% (95% CI 53.5-65.3%, I2 = 0%, p = 0.742), 3.3% (95% CI 1.1-5.4%, I2 = 0%, p = 0.865) and 17.5% (95% CI 12.9-22.0%, I2 = 0%, p = 0.623), respectively. CONCLUSION: Accordingly, DCB has the potential to be used as a treatment for CTO in suitable patients.

Implantable antennas for biomedical applications: a systematic review.

This review presents an in-depth examination of implantable antennas for various biomedical purposes. The development of implantable antennas, including their designs, materials, and operating principles, are introduced at the beginning of the discussion. An overview of the many kinds of implantable antennas utilized in implantable medical devices (IMDs) are presented in this study. The article then discusses the important factors to consider when developing implantable antennas for biomedical purposes, including implant placement, frequency range, and power needs. This investigation additionally examines the challenges and limitations encountered with implantable antennas, including the limited space available within the human body, the requirement for biocompatible materials, the impact of surrounding tissue on antenna performance, tissue attenuation, and signal interference. This review also emphasizes the most recent advances in implanted antenna technology, such as wireless power transmission, multiband operation, and miniaturization. Furthermore, it offers illustrations of several biomedical uses for implantable antennas, including pacemaker, capsule endoscopy, intracranial pressure monitoring, retinal prostheses, and bone implants. This paper concludes with a discussion of the future of implantable antennas and their possible use in bioelectronic medicine and novel medical implants. Overall, this survey offers a thorough analysis of implantable antennas in biomedical applications, emphasizing their importance in the development of implantable medical technology.

Correlation between intraosseous thermal change and drilling impulse data during osteotomy within autonomous dental implant robotic system: An in vitro study.

OBJECTIVES: This study aims at examining the correlation of intraosseous temperature change with drilling impulse data during osteotomy and establishing real-time temperature prediction models. MATERIALS AND METHODS: A combination of in vitro bovine rib model and Autonomous Dental Implant Robotic System (ADIR) was set up, in which intraosseous temperature and drilling impulse data were measured using an infrared camera and a six-axis force/torque sensor respectively. A total of 800 drills with different parameters (e.g., drill diameter, drill wear, drilling speed, and thickness of cortical bone) were experimented, along with an independent test set of 200 drills. Pearson correlation analysis was done for linear relationship. Four machining learning (ML) algorithms (e.g., support vector regression [SVR], ridge regression [RR], extreme gradient boosting [XGboost], and artificial neural network [ANN]) were run for building prediction models. RESULTS: By incorporating different parameters, it was found that lower drilling speed, smaller drill diameter, more severe wear, and thicker cortical bone were associated with higher intraosseous temperature changes and longer time exposure and were accompanied with alterations in drilling impulse data. Pearson correlation analysis further identified highly linear correlation between drilling impulse data and thermal changes. Finally, four ML prediction models were established, among which XGboost model showed the best performance with the minimum error measurements in test set. CONCLUSION: The proof-of-concept study highlighted close correlation of drilling impulse data with intraosseous temperature change during osteotomy. The ML prediction models may inspire future improvement on prevention of thermal bone injury and intelligent design of robot-assisted implant surgery.

Relationship Between Advanced Footwear Technology Longitudinal Bending Stiffness and Energy Cost of Running.

INTRODUCTION/PURPOSE: Shoe longitudinal bending stiffness (LBS) is often considered to influence running economy (RE) and thus, running performance. However, previous results are mixed and LBS levels have not been studied in advanced footwear technology (AFT). The purpose of this study was to evaluate the effects of increased LBS from curved carbon fiber plates embedded within an AFT midsole compared to a traditional running shoe on RE and spatiotemporal parameters. METHODS: Twenty-one male trained runners completed three times 4 min at 13 km/h with two experimental shoe models with a curved carbon fiber plate embedded in an AFT midsole with different LBS values (Stiff: 35.5 N/mm and Stiffest: 43.1 N/mm), and a Control condition (no carbon fiber plate: 20.1 N/mm). We measured energy cost of running (W/kg) and spatiotemporal parameters in one visit. RESULTS: RE improved for the Stiff shoe condition (15.71 ± 0.95 W/kg; p < 0.001; n2 = 0.374) compared to the Control condition (16.13 ± 1.08 W/kg; 2.56%) and Stiffest condition (16.03 ± 1.19 W/kg; 1.98%). However, we found no significant differences between the Stiffest and Control conditions. Moreover, there were no spatiotemporal differences between shoe conditions. CONCLUSION: Changes in LBS in AFT influences RE suggesting that moderately stiff shoes have the most effective LBS to improve RE in AFT compared to very stiff shoes and traditional, flexible shoe conditions while running at 13 km/h.

Piezoelectric rubber sheet sensor: a promising tool for home sleep apnea testing.

PURPOSE: This study aimed to develop an unobtrusive method for home sleep apnea testing (HSAT) utilizing micromotion signals obtained by a piezoelectric rubber sheet sensor. METHODS: Algorithms were designated to extract respiratory and ballistocardiogram components from micromotion signals and to detect respiratory events as the characteristic separation of the fast envelope of the respiration component from the slow envelope. In 78 adults with diagnosed or suspected sleep apnea, micromotion signal was recorded with a piezoelectric rubber sheet sensor placed beneath the bedsheet during polysomnography. In a half of the subjects, the algorithms were optimized to calculate respiratory event index (REI), estimating apnea-hypopnea index (AHI). In the other half of subjects, the performance of REI in classifying sleep apnea severity was evaluated. Additionally, the predictive value of the frequency of cyclic variation in heart rate (Fcv) obtained from the ballistocardiogram was assessed. RESULTS: In the training group, the optimized REI showed a strong correlation with the AHI (r = 0.93). Using the optimal cutoff of REI ≥ 14/h, subjects with an AHI ≥ 15 were identified with 77.8% sensitivity and 90.5% specificity. When applying this REI to the test group, it correlated closely with the AHI (r = 0.92) and identified subjects with an AHI ≥ 15 with 87.5% sensitivity and 91.3% specificity. While Fcv showed a modest correlation with AHI (r = 0.46 and 0.66 in the training and test groups), it lacked independent predictive power for AHI. CONCLUSION: The analysis of respiratory component of micromotion using piezoelectric rubber sheet sensors presents a promising approach for HSAT, providing a practical and effective means of estimating sleep apnea severity.

Channelled versus nonchannelled Macintosh videolaryngoscope blades in patients with a cervical collar: a randomized controlled noninferiority trial.

PURPOSE: Channelled blades have the advantage of avoiding stylet use and potential airway injury during videolaryngoscopic intubation. Nevertheless, the effectiveness of channelled Macintosh-type blades has not yet been fully established. We sought to assess the utility of channelled Macintosh-type blades for videolaryngoscopic intubation under cervical spine immobilization. METHODS: We conducted a randomized controlled noninferiority trial in neurosurgical patients with a difficult airway simulated by a cervical collar. Videolaryngoscopic intubation with a reinforced tracheal tube was performed using a channelled Macintosh-type blade without a stylet (channelled group, n = 130) or a nonchannelled Macintosh-type blade with a stylet (nonchannelled group, n = 131). The primary outcome was intubation success rate. Secondary outcomes included time to intubation and incidence or severity of intubation-related complications (subglottic, lingual, and dental injuries; bleeding; sore throat; and hoarseness). RESULTS: The initial intubation success rate was 98% and 99% in the channelled and nonchannelled groups, respectively, showing the noninferiority of the channelled group (difference in proportions -0.8%; 95% confidence interval [CI], -4.8% to 2.9%; predefined noninferiority margin, -5%; P = 0.62). Fewer participants in the channelled group had subglottic injuries than in the nonchannelled group (32% [32/100] vs 57% [54/95]; difference in proportions, -25%; 95% CI, -39% to -11%; P < 0.001). There were no significant differences between the two groups in the overall intubation success rate, time to intubation, and incidence or severity of other intubation-related complications. CONCLUSIONS: For videolaryngoscopic intubation in patients with a cervical collar, channelled Macintosh-type blades are an alternative to nonchannelled Macintosh-type blades, with a noninferior initial intubation success rate and a lower incidence of subglottic injury. STUDY REGISTRATION: CRIS.nih.go.kr ( KCT0005186 ); first submitted 29 June 2020.

RéSUMé: OBJECTIF: Les lames avec canal ont l'avantage de ne pas nécessiter l'utilisation d'un stylet et d'ainsi éviter les lésions potentielles des voies aériennes lors de l'intubation vidéolaryngoscopique. Néanmoins, l'efficacité des lames avec canal de type Macintosh n'a pas encore été pleinement établie. Nous avons cherché à évaluer l'utilité des lames avec canal de type Macintosh pour l'intubation vidéolaryngoscopique lorsque le rachis cervical était immobilisé. MéTHODE: Nous avons mené une étude randomisée contrôlée de non-infériorité chez des patient·es de neurochirurgie présentant des voies aériennes difficiles simulées par le port d'un collier cervical. L'intubation vidéolaryngoscopique avec une sonde trachéale renforcée a été réalisée à l'aide d'une lame Macintosh avec canal sans stylet (groupe avec canal, n = 130) ou d'une lame Macintosh sans canal avec stylet (groupe sans canal, n = 131). Le critère d'évaluation principal était le taux de réussite de l'intubation. Les critères d'évaluation secondaires comprenaient le temps d'intubation et l'incidence ou la gravité des complications liées à l'intubation (lésions sous-glottiques, linguales et dentaires, saignements, maux de gorge et enrouement). RéSULTATS: Le taux de réussite initial de l'intubation était de 98 % et 99 % dans les groupes avec et sans canal, respectivement, montrant la non-infériorité du groupe lame avec canal (différence de proportions −0,8 %; intervalle de confiance [IC] à 95 %, −4,8 % à 2,9 %; marge de non-infériorité prédéfinie, −5 %; P = 0,62). Les lésions sous-glottiques ont été moins nombreuses dans le groupe avec canal que dans le groupe sans canal (32 % [32/100] vs 57 % [54/95]; différence de proportions, −25 %; IC 95 %, −39 % à −11 %; P < 0,001). Il n'y avait pas de différences significatives entre les deux groupes en matière de taux global de réussite de l'intubation, de temps d'intubation et d'incidence ou de gravité des autres complications liées à l'intubation. CONCLUSION: Pour l'intubation vidéolaryngoscopique des patient·es portant un collier cervical, les lames avec canal de type Macintosh constituent une alternative aux lames sans canal de type Macintosh, avec un taux de réussite d'intubation initial non inférieur et une incidence plus faible de lésions sous-glottiques. ENREGISTREMENT DE L'éTUDE: CRIS.nih.go.kr ( KCT0005186 ); première soumission le 29 juin 2020.

Pressure Infusor Assisted Arthrocentesis.

Temporomandibular joint internal disorders commonly present with limited mouth opening and pain. Treatment options range from invasive surgical procedures to minimally invasive interventions. This technical note aims to introduce a modification to the arthrocentesis technique in which a pressure infusion cuff (VBM Classic Infusor, Medizintechnik GmbH, Germany) is used for irrigation instead of syringes or peristaltic pumps. A pressure infusion cuff (bag) is an inflatable bag with a hand pump and a sphygmomanometer that allows monitorization of the pressure, and it is intended to apply pressure on intravenous fluid bags to assist with rapid infusion of fluids. This allows the operator to maintain an efficient and stable flow pressure throughout the procedure while avoiding occupational hand and wrist problems resulting from manual irrigation with syringes. Furthermore, pressure monitoring, as read on the sphygmomanometer of the cuff, facilitates the manipulation of the needles and adjustment of the pressure should the patient experience discomfort. This increases the patient's compliance, physician's comfort, and allows the collection of quantitative data in clinical studies.

Modeling programmable drug delivery in bioelectronics with electrochemical actuation.

Drug delivery systems featuring electrochemical actuation represent an emerging class of biomedical technology with programmable volume/flowrate capabilities for localized delivery. Recent work establishes applications in neuroscience experiments involving small animals in the context of pharmacological response. However, for programmable delivery, the available flowrate control and delivery time models fail to consider key variables of the drug delivery system--microfluidic resistance and membrane stiffness. Here we establish an analytical model that accounts for the missing variables and provides a scalable understanding of each variable influence in the physics of delivery process (i.e., maximum flowrate, delivery time). This analytical model accounts for the key parameters--initial environmental pressure, initial volume, microfluidic resistance, flexible membrane, current, and temperature--to control the delivery and bypasses numerical simulations allowing faster system optimization for different in vivo experiments. We show that the delivery process is controlled by three nondimensional parameters, and the volume/flowrate results from the proposed analytical model agree with the numerical results and experiments. These results have relevance to the many emerging applications of programmable delivery in clinical studies within the neuroscience and broader biomedical communities.

Multimethod analysis of large- and low-tapered single file reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow.

AIM: To compare eight large- and low-tapered heat-treated reciprocating instruments regarding their design, metallurgy, mechanical properties, and irrigation flow through an in silico model. METHODOLOGY: A total of 472 new 25-mm E-Flex Rex (25/.04 and 25/.06), Excalibur (25/.05), Procodile (25/.06), Reciproc Blue R25 (25/.08v), WaveOne Gold Primary (25/.07v), and Univy Sense (25/.04 and 25/.06) instruments were evaluated regarding their design (stereomicroscopy, scanning electron microscopy, and 3D surface scanning), metallurgy (energy-dispersive X-ray spectroscopy and differential scanning calorimetry), and mechanical performance (cyclic fatigue, torsional resistance, cutting ability, bending and buckling resistance). Computational fluid dynamics assessment was also conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparations. Kruskal-Wallis and one-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Instruments presented variations in blade numbers, helical angles, and tip designs, with all featuring non-active tips, symmetrical blades, and equiatomic nickel-titanium ratios. Cross-sectional designs exhibited an S-shaped geometry, except for WaveOne Gold. Univy 25/.04 and Reciproc Blue displayed the smallest and largest core diameters at D3. Univy 25/.04 and E-Flex Rec 25/.04 demonstrated the longest time to fracture (p < .05). Reciproc Blue and Univy 25/.04 exhibited the highest and lowest torque to fracture, respectively (p < .05). Univy 25/.04 and Reciproc Blue had the highest rotation angles, whilst E-Flex Rec 25/.06 showed the lowest angle (p < .05). The better cutting ability was observed with E-Flex Rec 25/.06, Procodile, Excalibur, and Reciproc Blue (p > .05). Reciproc R25 and E-Flex Rec showed the highest buckling resistance values (p < .05), with WaveOne Gold being the least flexible instrument. The impact of instruments' size and taper on wall shear stress and apical pressure did not follow a distinct pattern, although Univy 25/.04 and E-Flex Rec 25/.06 yielded the highest and lowest values for both parameters, respectively. CONCLUSIONS: Low-tapered reciprocating instruments exhibit increased flexibility, higher time to fracture, and greater angles of rotation, coupled with reduced maximum bending loads and buckling strength compared to large-tapered instruments. Nevertheless, low-tapered systems also exhibit lower maximum torque to fracture and inferior cutting ability, contributing to a narrower apical canal enlargement that may compromise the penetration of irrigants in that region.

Substance P/calcitonin gene-related peptide and their receptors expression in human periodontal ligament after root canal preparation with five different systems.

AIM: The purpose of this study was to quantify the effect of five different root canal preparation instruments on Substance P (SP), Calcitonin gene-related peptide (CGRP) and their receptors expression in healthy human periodontal ligament. METHODOLOGY: STROBE guidelines were used to design a study using 60 periodontal ligament samples obtained from healthy lower premolars where extraction was indicated for orthodontic reasons. Prior to extraction 40 of these premolars were equally divided into four groups and root canals were prepared using different systems: Mtwo, Reciproc Blue, HyFlex EDM and Plex-V. Ten premolars were prepared with hand files and served as a positive control group. The remaining 10 premolars where extracted without treatment and served as a negative control group. All periodontal ligament samples were processed to measure the expression of SP, CGRP and their receptors by radioimmunoassay. Kruskal-Wallis and Duncan tests were performed to determine statistically significant differences between the groups for each variable. RESULTS: Greater expression of all the peptides measured were found in the hand-file preparation group, followed by the Reciproc Blue, Mtwo, HyFlex EDM and Plex-V groups. The lower SP, CGRP and their receptors values were for the intact teeth control group. Kruskal-Wallis test showed statistically significant differences amongst groups (p < .001). Dunn post-hoc tests showed statistically significant differences in SP, CGRP and their receptors expression between the intact teeth and the hand-file and Reciproc Blue groups. Hand-file group showed significant differences with the other groups, except with Reciproc Blue, where no differences were observed in any of the peptides measured. Finally, no differences were observed between Plex-V and HyFlex in any of the peptides measured. CONCLUSIONS: Root canal preparation with hand files and Reciproc Blue generates the highest expression of SP, CGRP, NK1 and CGRP1R in human periodontal ligament, whilst Plex-V and HyFlex maintain the basal expression of neuropeptides and their receptors. Mtwo showed intermediate results between Reciproc Blue and HyFlex.

Exploring morphometric transformations in temperature-sensitive NiTi instruments alongside real-time intracanal temperature dynamics.

AIM: This study was twofold: (i) it aimed to investigate the morphometric changes of three temperature-sensitive nickel-titanium (NiTi) instruments at different temperatures, and (ii) to conduct an in vivo real-time analysis of intracanal temperature changes. METHODS: Changes in the shape and length of XP-Endo Shaper, XP-Endo Finisher, and XP-Endo Finisher-R were evaluated in real time whilst heated in a temperature-controlled water bath from 22 to 45°C. Instruments were fixed to a laminated water-resistant 1 mm graph paper attached to a stone block. Instruments were imaged whilst subjected to increasing temperature using a digital camera attached to an operating microscope. From recorded videos, still frames were extracted at 10-s intervals and changes in the length and shape of each instrument were measured and changes were plotted against time. Moreover, the intracanal temperature of distal roots of lower molars was measured in vivo for patients attending the clinic for non-surgical root canal treatments. The temperature was measured using a K-type thermocouple probe inserted into the mid-root level after irrigating the canal with a solution set at room temperature (22°C) or heated to 45°C. The intraoral and intracanal temperatures were recorded using a video camera for 180 s at 5-s intervals to plot the change in the intraoral and intracanal temperature, after both irrigation solution temperatures, with time. RESULTS: The shape transformation of XP-Endo Shaper began at 31.5 ± 2.0°C and reached its optimal transformation at 35.1 ± 1.0°C. For the Finisher and Finisher-R, shape transformations began at 29.2 ± 1.9 and 26.9 ± 2.2°C reaching the optimal transformation at 33.9 ± 1.4 and 32.7 ± 1.7°C, respectively. The average decreases in lengths of XP-Endo Shaper, Finisher, and Finisher-R after full transformation were 0.43 ± 0.23, 1.07 ± 0.22, and 1.15 ± 0.22 mm, respectively. The intracanal temperature reached 32.9 ± 0.8 and 33.2 ± 1.0°C after 3 min of application of irrigation solutions set at 22 or 45°C, respectively. CONCLUSION: The tested instruments exhibited diverse changes in their shapes and lengths at varying temperatures. Despite the temperature of the irrigation solution, the intracanal temperature consistently remained lower than the intracanal temperature once equilibrium was reached. This highlights the importance of considering the temperature of irrigation solution during in vitro testing of endodontic instruments.

Efficacy of an automatic electric toothbrush with nylon bristles in dental plaque removal: a cross-over randomized controlled trial.

OBJECTIVES: The objective of this single-use, five-treatment, five-period, cross-over randomized controlled trial (RCT) was to compare the efficacy in dental plaque removal of a new Y-shaped automatic electric toothbrush (Y-brush) compared to a U-shaped automatic electric toothbrush (U-brush), a manual toothbrushing procedure (for 45 and 120 s), and no brushing (negative control). MATERIALS AND METHODS: Eligible participants were volunteer students randomized to the treatments in the five periods of the study. The primary outcome measure was the reduction in full-mouth plaque score (FMPS) after brushing while the secondary outcome variable was a visual analogic scale (VAS) on subjective clean mouth sensation. Mixed models were performed for difference in FMPS and VAS. RESULTS: After brushing procedures, manual toothbrushing (120 s) showed a statistically significant reduction in FMPS than Y-brush (difference 36.9; 95%CI 29.6 to 44.1, p < 0.0001), U-brush (difference 42.3; 95%CI 35.1 to 49.6, p < 0.0001), manual brushing (45 s) (difference 13.8; 95%CI 6.5 to 21.1, p < 0.0001), and No brushing (difference 46.6; 95%CI 39.3 to 53.9, p < 0.0001). Y-brush was significantly more effective than No brushing (difference 9.8; 95%CI 2.5 to 17.0, p = 0.0030), while there was no significant difference compared to U- brush. Similar results were obtained for the differences in the Clean Mouth VAS. CONCLUSIONS: Y-brush was significantly more effective than no brushing (negative control) in removing dental plaque. When compared to manual toothbrushing for both 45 and 120 s, however, Y-brush was less effective in dental plaque removal. CLINICAL RELEVANCE: Modified design of automatic toothbrushing devices could improve plaque reduction, especially in patients with intellectual disabilities or motor difficulties.

In-vitro effects of novel periodontal scalers with a planar ultrasonic piezoelectric transducer on periodontal biofilm removal, dentine surface roughness, and periodontal ligament fibroblasts adhesion.

OBJECTIVES: To compare ultrasonic scaler prototypes based on a planar piezoelectric transducer with different working frequencies featuring a titanium (Ti-20, Ti-28, and Ti-40) or stainless steel (SS-28) instrument, with a commercially available scaler (com-29) in terms of biofilm removal and reformation, dentine surface roughness and adhesion of periodontal fibroblasts. MATERIALS AND METHODS: A periodontal multi-species biofilm was formed on specimens with dentine slices. Thereafter specimens were instrumented with scalers in a periodontal pocket model or left untreated (control). The remaining biofilms were quantified and allowed to reform on instrumented dentine slices. In addition, fibroblasts were seeded for attachment evaluation after 72 h of incubation. Dentine surface roughness was analyzed before and after instrumentation. RESULTS: All tested instruments reduced the colony-forming unit (cfu) counts by about 3 to 4 log10 and the biofilm quantity (each p < 0.01 vs. control), but with no statistically significant difference between the instrumented groups. After 24-hour biofilm reformation, no differences in cfu counts were observed between any groups, but the biofilm quantity was about 50% in all instrumented groups compared to the control. The attachment of fibroblasts on instrumented dentine was significantly higher than on untreated dentine (p < 0.05), with the exception of Ti-20. The dentine surface roughness was not affected by any instrumentation. CONCLUSIONS: The planar piezoelectric scaler prototypes are able to efficiently remove biofilm without dentine surface alterations, regardless of the operating frequency or instrument material. CLINICAL RELEVANCE: Ultrasonic scalers based on a planar piezoelectric transducer might be an alternative to currently available ultrasonic scalers.

Cleansing efficacy of the electric toothbrush Oral-B® iO™ compared to conventional oscillating-rotating technology: a randomized-controlled study.

OBJECTIVES: This study aimed to compare the cleansing efficacy of the Oral-B® iO™ electric toothbrush incorporating oscillating-rotating technology with microvibrations - with a traditional oscillating-rotating toothbrush. MATERIALS AND METHODS: Thirty adult participants were randomly assigned to use the iO™ electric toothbrush with the brush head iO™ Ultimate Clean or the traditional oscillating-rotating toothbrush Oral-B® Genius® with the Cross-Action brush head. Oral hygiene indices (Rustogi Modified Navy Plaque Index and Gingival Bleeding Index) were assessed before and after 28 days of home use of the assigned product. Participants were instructed to refrain from interdental hygiene during the study period. After a 2-week washout period, the clinical investigation was repeated in a crossover design. RESULTS: All 30 participants completed the study with no dropouts. After 28 days of use, the iO™ showed statistically significantly lower plaque levels than the conventional oscillating-rotating toothbrush (25.09% vs. 30.60%, p = 0.029). This difference was particularly noticeable in marginal and approximal areas. There were no significant distinctions in gingival bleeding indices. CONCLUSIONS: The Oral-B® iO™ electric toothbrush displayed enhanced plaque removal efficiency compared to a conventional oscillating-rotating technology. CLINICAL RELEVANCE: This study highlights the potential benefits of advanced toothbrush technologies for plaque reduction and encourages further research.