Advanced Interface Engineering in Gradient Core/Shell Quantum Dots Enables Efficient Photoelectrochemical Hydrogen Evolution.

Semiconductor core/shell quantum dots (QDs) are considered promising building blocks to fabricate photoelectrochemical (PEC) cells for the direct conversion of solar energy into hydrogen (H2). However, the lattice mismatch between core and shell in such QDs results in undesirable defects and severe carrier recombination, limiting photo-induced carrier separation/transfer and solar-to-fuel conversion efficiency. Here, an interface engineering approach is explored to minimize the core-shell lattice mismatch in CdS/CdSexS1-x (x = 0.09-1) core/shell QDs (g-CSG). As a proof-of-concept, PEC cells based on g-CSG QDs yield a remarkable photocurrent density of 13.1 mA cm-2 under AM 1.5 G one-sun illumination (100 mW cm-2), which is ≈54.1% and ≈33.7% higher compared to that in CdS/CdSe0.5S0.5 (g-CSA) and CdS/CdSe QDs (g-CS), respectively. Theoretical calculations and carrier dynamics confirm more efficient carrier separation and charge transfer rate in g-CSG QDs with respect to g-CSA and g-CS QDs. These results are attributed to the minimization of the core-shell lattice mismatch by the cascade gradient shell in g-CSG QDs, which modifies carrier confinement potential and reduces interfacial defects. This work provides fundamental insights into the interface engineering of core/shell QDs and may open up new avenues to boost the performance of PEC cells for H2 evolution and other QDs-based optoelectronic devices.

Investigating Plasmonic Catalysis Kinetics on Hot-Spot Engineered Nanoantennae.

Strong hot-spots can facilitate photocatalytic reactions potentially providing effective solar-to-chemical energy conversion pathways. Although it is well-known that the local electromagnetic field in plasmonic nanocavities increases as the cavity size reduces, the influence of hot-spots on photocatalytic reactions remains elusive. Herein, we explored hot-spot dependent catalytic behaviors on a highly controlled platform with varying interparticle distances. Plasmon-meditated dehalogenation of 4-iodothiophenol was employed to observe time-resolved catalytic behaviors via in situ surface-enhanced Raman spectroscopy on dimers with 5, 10, 20, and 30 nm interparticle distances. As a result, we show that by reducing the gap from 20 to 10 nm, the reaction rate can be sped up more than 2 times. Further reduction in the interparticle distance did not improve reaction rate significantly although the maximum local-field was ∼2.3-fold stronger. Our combined experimental and theoretical study provides valuable insights in designing novel plasmonic photocatalytic platforms.

Unraveling the Chirality Transfer from Circularly Polarized Light to Single Plasmonic Nanoparticles.

Due to their broken symmetry, chiral plasmonic nanostructures have unique optical properties and numerous applications. However, there is still a lack of comprehension regarding how chirality transfer occurs between circularly polarized light (CPL) and these structures. Here, we thoroughly investigate the plasmon-assisted growth of chiral nanoparticles from achiral Au nanocubes (AuNCs) via CPL without the involvement of any chiral molecule stimulators. We identify the structural chirality of our synthesized chiral plasmonic nanostructures using circular differential scattering (CDS) spectroscopy, which is correlated with scanning electron microscopy imaging at both the single-particle and ensemble levels. Theoretical simulations, including hot-electron surface maps, reveal that the plasmon-induced chirality transfer is mediated by the asymmetric distribution of hot electrons on achiral AuNCs under CPL excitation. Furthermore, we shed light on how this plasmon-induced chirality transfer can also be utilized for chiral growth in bimetallic systems, such as Ag or Pd on AuNCs. The results presented here uncover fundamental aspects of chiral light-matter interaction and have implications for the future design and optimization of chiral sensors and chiral catalysis, among others.

Applications of Plasmon-Enhanced Nanocatalysis to Organic Transformations.

Localized surface plasmon resonance (LSPR) is a physical phenomenon exhibited by nanoparticles of metals including coinage metals, alkali metals, aluminum, and some semiconductors which translates into electromagnetic, thermal, and chemical properties. In the past decade, LSPR has been taken advantage of in the context of catalysis. While plasmonic nanoparticles (PNPs) have been successfully applied toward enhancing catalysis of inorganic reactions such as water splitting, they have also demonstrated exciting performance in the catalysis of organic transformations with potential applications in synthesis of molecules from commodity to pharmaceutical compounds. The advantages of this approach include improved selectivity, enhanced reaction rates, and milder reaction conditions. This review provides the basics of LSPR theory, details the mechanisms at play in plasmon-enhanced nanocatalysis, sheds light onto such nanocatalyst design, and finally systematically presents the breadth of organic reactions hence catalyzed.

Chiral Photomelting of DNA-Nanocrystal Assemblies Utilizing Plasmonic Photoheating.

Chiral plasmonic nanostructures exhibit anomalously strong chiroptical signals and offer the possibility to realize asymmetric photophysical and photochemical processes controlled by circularly polarized light. Here, we use a chiral DNA-assembled nanorod pair as a model system for chiral plasmonic photomelting. We show that both the enantiomeric excess and consequent circular dichroism can be controlled with chiral light. The nonlinear chiroptical response of our plasmonic system results from the chiral photothermal effect leading to selective melting of the DNA linker strands. Our study describes both the single-complex and collective heating regimes, which should be treated with different models. The chiral asymmetry factors of the calculated photothermal and photomelting effects exceed the values typical for the chiral molecular photochemistry at least 10-fold. Our proposed mechanism can be used to develop chiral photoresponsive systems controllable with circularly polarized light.

Local Growth Mediated by Plasmonic Hot Carriers: Chirality from Achiral Nanocrystals Using Circularly Polarized Light.

Plasmonic nanocrystals and their assemblies are excellent tools to create functional systems, including systems with strong chiral optical responses. Here we study the possibility of growing chiral plasmonic nanocrystals from strictly nonchiral seeds of different types by using circularly polarized light as the chirality-inducing mechanism. We present a novel theoretical methodology that simulates realistic nonlinear and inhomogeneous photogrowth processes in plasmonic nanocrystals, mediated by the excitation of hot carriers that can drive surface chemistry. We show the strongly anisotropic and chiral growth of oriented nanocrystals with lowered symmetry, with the striking feature that such chiral growth can appear even for nanocrystals with subwavelength sizes. Furthermore, we show that the chiral growth of nanocrystals in solution is fundamentally challenging. This work explores new ways of growing monolithic chiral plasmonic nanostructures and can be useful for the development of plasmonic photocatalysis and fabrication technologies.

Distance Dependence of Förster Resonance Energy Transfer Rates in 2D Perovskite Quantum Wells via Control of Organic Spacer Length.

Two-dimensional (2D) semiconductors are attractive candidates for a variety of optoelectronic applications owing to the unique electronic properties that arise from quantum confinement along a single dimension. Incorporating nonradiative mechanisms that enable directed migration of bound charge carriers, such as Förster resonance energy transfer (FRET), could boost device efficiencies provided that FRET rates outpace undesired relaxation pathways. However, predictive models for FRET between distinct 2D states are lacking, particularly with respect to the distance d between a donor and acceptor. We approach FRET in systems with binary mixtures of donor and acceptor 2D perovskite quantum wells (PQWs), and we synthetically tune distances between donor and acceptor by varying alkylammonium spacer cation lengths. FRET rates are monitored using transient absorption spectroscopy and ultrafast photoluminescence, revealing rapid picosecond lifetimes that scale with spacer cation length. We theoretically model these binary mixtures of PQWs, describing the emitters as classical oscillating dipoles. We find agreement with our empirical lifetimes and then determine the effects of lateral extent and layer thickness, establishing fundamental principles for FRET in 2D materials.

Hot Electrons Generated in Chiral Plasmonic Nanocrystals as a Mechanism for Surface Photochemistry and Chiral Growth.

The realization of chiral photochemical reactions at the molecular level has proven to be a challenging task, with invariably low efficiencies originating from very small optical circular dichroism signals. On the contrary, colloidal nanocrystals offer a very large differential response to circularly polarized light when designed with chiral geometries. We propose taking advantage of this capability, introducing a novel mechanism driving surface photochemistry in a chiral nanocrystal. Plasmonic nanocrystals exhibit anomalously large asymmetry factors in optical circular dichroism (CD), and the related hot-electron generation shows in turn a very strong asymmetry, serving as a mechanism for chiral growth. Through theoretical modeling, we show that chiral plasmonic nanocrystals can enable chiral surface growth based on the generation of energetic (hot) electrons. Using simple and realistic phenomenological models, we illustrate how this kind of surface photochemistry can be observed experimentally. The proposed mechanism is efficient if it operates on an already strongly chiral nanocrystal, whereas our proposed mechanism does not show chiral growth for initially nonchiral structures in a solution. The asymmetry factors for the chiral effects, driven by hot electrons, exceed the values observed in chiral molecular photophysics at least 10-fold. The proposed chiral-growth mechanism for the transformation of plasmonic colloids is fundamentally different to the traditional schemes of chiral photochemistry at the molecular level.

Chiral Plasmonic Nanocrystals for Generation of Hot Electrons: Toward Polarization-Sensitive Photochemistry.

The use of biomaterials, with techniques such as DNA-directed assembly or biodirected synthesis, can surpass top-down fabrication techniques in creating plasmonic superstructures in terms of spatial resolution, range of functionality, and fabrication speed. In particular, by enabling a very precise placement of nanoparticles in a bioassembled complex or through the controlled biodirected shaping of single nanoparticles, plasmonic nanocrystals can show remarkably strong circular dichroism (CD) signals. We show that chiral bioplasmonic assemblies and single nanocrystals can enable polarization-sensitive photochemistry based on the generation of energetic (hot) electrons. It is now established that hot plasmonic electrons can induce surface photochemistry or even reshape plasmonic nanocrystals. We show that merging chiral plasmonic nanocrystal systems and the hot-election generation effect offers unique possibilities in photochemistry, such as polarization-sensitive photochemistry promoting nonchiral molecular reactions, chiral photoinduced growth of a colloid at the atomic level, and chiral photochemical destruction of chiral nanocrystals. In contrast, for chiral molecular systems, the equivalent of the described effects is challenging to observe because molecular species typically exhibit very small CD signals. Moreover, we compare our findings with traditional chiral photochemistry at the molecular level, identifying new, different regimes for chiral photochemistry with possibilities that are unique for plasmonic colloidal systems. In this study, we bring together the concept of hot-electron generation and the field of chiral colloidal plasmonics. Using chiral plasmonic nanorod complexes as a model system, we demonstrate remarkably strong CD in both optical extinction and generation rates of hot electrons. Studying the regime of steady-state excitation, we discuss the influence of geometrical and material parameters on the chiral effects involved in the generation of hot electrons. Optical chirality and the chiral hot-electron response in the nanorod dimers result from complex interparticle interactions, which can appear in the weak coupling regime or in the form of Rabi splitting. Regarding practical applications, our study suggests interesting opportunities in polarization-sensitive photochemistry, in chiral recognition or separation, and in promoting chiral crystal growth at the nanoscale.

Hybrid Plasmonic-Aerogel Materials as Optical Superheaters with Engineered Resonances.

Solar radiation is a versatile source of energy, convertible to different forms of power. A direct path to exploit it is the generation of heat, for applications including passive building heating, but it can also drive secondary energy-conversion steps. We present a novel concept for a hybrid material which is both strongly photo-absorbing and with superior characteristics for the insulation of heat. The combination of that two properties is rather unique, and make this material an optical superheater. To realize such a material, we are combining plasmonic nanoheaters with alumina aerogel. The aerogel has the double function of providing structural support for plasmonic nanocrystals, which serve as nanoheaters, and reducing the diffusion rate of the heat generated by them, resulting in large local temperature increases under a relatively low radiation intensity. This work includes theoretical discussion on the physical mechanisms impacting the system's balanced thermal equilibrium.

Generation of hot electrons in nanostructures incorporating conventional and unconventional plasmonic materials.

The generation of energetic electrons is an effect occurring in any plasmonic nanostructure. However, the number of electrons with high energies generated optically in a plasmonic nanostructure can be relatively small. This is an intrinsic property of the collective plasmon excitations in a Fermi gas of electrons. But the choices of material and geometry have a great impact on the generation rate, and are therefore crucial for designing a nanostructure with a large rate of generation of energetic (hot) electrons. Here we test different plasmonic materials from the point of view of the generation of hot electrons (HEs). Our choice of materials includes both strongly-plasmonic materials (Au, Ag, Cu and Al) and crystals with strongly broadened plasmonic resonances (Pt, TiN and ZrN). Regarding the choice of geometry, we consider two types of nanostructures, single nanocrystals deposited over a dielectric substrate and metastructure absorbers, observing interesting opto-electronic properties. For single nanocrystals, the rate of HE generation is strongly material-dependent since the HE generation rate strongly depends on several physical parameters such as plasmonic enhancement, plasmonic resonance wavelength, Fermi energy, etc. Interestingly, the plasmonic meta-absorbers exhibit a different behaviour. The strongly-plasmonic metals, such as Au, Ag, Cu or Al, show very similar performances, while the materials with damped plasmon resonances demonstrate diverse and reduced rates of HE generation. The physical reason for these different behaviours lies in the dielectric functions of these materials. In the metastructures, plasmonic resonances are in the infrared region and the strongly-plasmonic materials behave as an almost ideal metal, whereas the second group of materials exhibits strong dissipation. This makes the responses from the metastructures made of crystals with damped plasmons strongly dependent on the choice of material. The physical principles described in our study can be useful for designing metastructures and nanodevices based on HEs, which can be used in photo-chemistry and opto-electronics.

Highly Efficient Copper Sulfide-Based Near-Infrared Photothermal Agents: Exploring the Limits of Macroscopic Heat Conversion.

Among the foreseeable therapeutic approaches at the cellular level, nanoplatform-driven photothermal therapy is a thriving tool for the selective eradication of malignant tissues with minimal side effects to healthy ones. Hence, chemically versatile, near-infrared absorbing plasmonic nanoparticles are distinctly appealing and most sought after as efficient photothermal agents. In this work, a straightforward method to synthesize monodisperse PEGylated copper sulfide nanoparticles of pure covellite (CuS) phase, featuring strong localized surface plasmonic resonance absorption in the near-infrared and flexible surface chemistry, imparted by monomethyl ether polyethylene glycol molecules, is developed and optimized. These nanoparticles show a remarkable photothermal heat conversion efficiency (HCE) of 71.4%, which is among the highest for CuS systems and rivals that of plasmonic noble metal nanostructures. Moreover, through critical evaluation and mathematical modeling of the material's properties and measurement methodology, it is assessed that the calculated HCE values drastically depend on experimental conditions such as wavelength-dependent solvent absorption properties, sol concentration, and optical path. These findings are of paramount relevance to the photothermal community, since they call for a standardization of the procedure for the evaluation of the HCE of proposed photothermal agents, in order to make the reported values universally and reliably comparable.

Metamaterial perfect absorber with unabated size-independent absorption.

Metamaterial absorbers open a new door for the design of optical harvesting devices ranging from the microwave to optical regimes. The top resonator in these structures is critical for the function of metamaterial absorbers. The resonant frequency, bandwidth, and maximum absorption mainly depend on the choice of material, shape, and size of the top resonator. The maximum absorption is generally impaired as the size of the resonator changes, due to the high sensitivity of impedance matching with the medium. In this paper, we experimentally demonstrate a metamaterial perfect absorber with unabated absorption as its resonator's size changes. The perfect absorber is based on an array of metal squares inscribed with a hollow square. The absorption maxima stay above 98% as the size changes from 600 to 1500 nm in the mid-infrared region, agreeing with simulated results yielding an absorption of ~100%. The unabated absorption properties can be interpreted by the equivalent circuit theory. Moreover, the experimental absorption remains above 91% for incident angles change up to 50°, both for TE and TM polarization. Our work offers a method for achieving stable perfect absorption in sensing, filtering, and selective thermal emission.

Broadband Absorbing Exciton-Plasmon Metafluids with Narrow Transparency Windows.

Optical metafluids that consist of colloidal solutions of plasmonic and/or excitonic nanomaterials may play important roles as functional working fluids or as means for producing solid metamaterial coatings. The concept of a metafluid employed here is based on the picture that a single ballistic photon, propagating through the metafluid, interacts with a large collection of specifically designed optically active nanocrystals. We demonstrate water-based metafluids that act as broadband electromagnetic absorbers in a spectral range of 200-3300 nm and feature a tunable narrow (∼100 nm) transparency window in the visible-to-near-infrared region. To define this transparency window, we employ plasmonic gold nanorods. We utilize excitonic boron-doped silicon nanocrystals as opaque optical absorbers ("optical wall") in the UV and blue-green range of the spectrum. Water itself acts as an opaque "wall" in the near-infrared to infrared. We explore the limits of the concept of a "simple" metafluid by computationally testing and validating the effective medium approach based on the Beer-Lambert law. According to our simulations and experiments, particle aggregation and the associated decay of the window effect are one example of the failure of the simple metafluid concept due to strong interparticle interactions.

Differentiating Plasmon-Enhanced Chemical Reactions on AgPd Hollow Nanoplates through Surface-Enhanced Raman Spectroscopy.

Plasmonic photocatalysis demonstrates great potential for efficiently harnessing light energy. However, the underlying mechanisms remain enigmatic due to the transient nature of the reaction processes. Typically, plasmonic photocatalysis relies on the excitation of surface plasmon resonance (SPR) in plasmonic materials, such as metal nanoparticles, leading to the generation of high-energy or "hot electrons", albeit accompanied by photothermal heating or Joule effect. The ability of hot electrons to participate in chemical reactions is one of the key mechanisms, underlying the enhanced photocatalytic activity observed in plasmonic photocatalysis. Interestingly, surface-enhanced Raman scattering (SERS) spectroscopy allows the analysis of chemical reactions driven by hot electrons, as both SERS and hot electrons stem from the decay of SPR and occur at the hot spots. Herein, we propose a highly efficient SERS substrate based on cellulose paper loaded with either Ag nanoplates (Ag NPs) or AgPd hollow nanoplates (AgPd HNPs) for the in situ monitoring of C-C homocoupling reactions. The data analysis allowed us to disentangle the impact of hot electrons and the Joule effect on plasmon-enhanced photocatalysis. Computational simulations revealed an increase in the rate of excitation of hot carriers from single/isolated AgPd HNPs to an in-plane with a vertical stacking assembly, suggesting its promise as a photocatalyst under broadband light. In addition, the results suggest that the incorporation of Pd into an alloy with plasmonic properties may enhance its catalytic performance under light irradiation due to the collection of plasmon-excitation-induced hot electrons. This work has demonstrated the performance-oriented synthesis of hybrid nanostructures, providing a unique route to uncover the mechanism of plasmon-enhanced photocatalysis.

Balancing Near-Field Enhancement and Hot Carrier Injection: Plasmonic Photocatalysis in Energy-Transfer Cascade Assemblies.

Photocatalysis stands as a very promising alternative to photovoltaics in exploiting solar energy and storing it in chemical products through a single-step process. A central obstacle to its broad implementation is its low conversion efficiency, motivating research in different fields to bring about a breakthrough in this technology. Using plasmonic materials to photosensitize traditional semiconductor photocatalysts is a popular strategy whose full potential is yet to be fully exploited. In this work, we use CdS quantum dots as a bridge system, reaping energy from Au nanostructures and delivering it to TiO2 nanoparticles serving as catalytic centers. The quantum dots can do this by becoming an intermediate step in a charge-transfer cascade initiated in the plasmonic system or by creating an electron-hole pair at an improved rate due to their interaction with the enhanced near-field created by the plasmonic nanoparticles. Our results show a significant acceleration in the reaction upon combining these elements in hybrid colloidal photocatalysts that promote the role of the near-field enhancement effect, and we show how to engineer complexes exploiting this approach. In doing so, we also explore the complex interplay between the different mechanisms involved in the photocatalytic process, highlighting the importance of the Au nanoparticles' morphology in their photosensitizing capabilities.

Silver nanoparticle enhanced metal-organic matrix with interface-engineering for efficient photocatalytic hydrogen evolution.

Integrating plasmonic nanoparticles into the photoactive metal-organic matrix is highly desirable due to the plasmonic near field enhancement, complementary light absorption, and accelerated separation of photogenerated charge carriers at the junction interface. The construction of a well-defined, intimate interface is vital for efficient charge carrier separation, however, it remains a challenge in synthesis. Here we synthesize a junction bearing intimate interface, composed of plasmonic Ag nanoparticles and matrix with silver node via a facile one-step approach. The plasmonic effect of Ag nanoparticles on the matrix is visualized through electron energy loss mapping. Moreover, charge carrier transfer from the plasmonic nanoparticles to the matrix is verified through ultrafast transient absorption spectroscopy and in-situ photoelectron spectroscopy. The system delivers highly efficient visible-light photocatalytic H2 generation, surpassing most reported metal-organic framework-based photocatalytic systems. This work sheds light on effective electronic and energy bridging between plasmonic nanoparticles and organic semiconductors.

Plasmonic photocatalysis in aqueous solution: assessing the contribution of thermal effects and evaluating the role of photogenerated ROS.

Plasmon-induced photocatalysis can drive photochemical processes with an unprecedented control of reactivity, using light as sole energy source. Nevertheless, disentangling the relative importance of thermal and non-thermal features upon plasmonic excitation remains a difficult task. In this work we intend to separate the role played by the photogenerated charge carriers from thermal mechanisms in the plasmonic photo-oxidation of a model organic substrate in aqueous solution and using a metal-semiconductor hybrid as model photocatalyst. Accordingly, we present a simple set of experimental procedures and simulations that allow us to discard the thermal dissipation upon plasmonic excitation as the main driving force behind these chemical reactions. Moreover, we also study the photogeneration of reactive oxygen species (ROS), discussing their fundamental role in photo-oxidation reactions and the information they provide regarding the reactivity of the photogenerated electrons and holes.

Synergistic Combination of Charge Carriers and Energy-Transfer Processes in Plasmonic Photocatalysis.

Important efforts are currently under way in order to develop further the nascent field of plasmonic photocatalysis, striving for improved efficiencies and selectivities. A significant fraction of such efforts has been focused on distinguishing, understanding, and enhancing specific energy-transfer mechanisms from plasmonic nanostructures to their environment. Herein, we report a synthetic strategy that combines two of the main physical mechanisms driving plasmonic photocatalysis into an engineered system by rationally combining the photochemical features of energetic charge carriers and the electromagnetic field enhancement inherent to the plasmonic excitation. We do so by creating hybrid photocatalysts that integrate multiple plasmonic resonators in a single entity, controlling their joint contribution through spectral separation and differential surface functionalization. This strategy allows us to create complex hybrids with improved photosensitization capabilities, thanks to the synergistic combination of two photosensitization mechanisms. Our results show that the hot electron injection can be combined with an energy-transfer process mediated by the near-field interaction, leading to a significant increase in the final photocatalytic response of the material and moving the field of plasmonic photocatalysis closer to energy-efficient applications. Furthermore, our multimodal hybrids offer a test system to probe the properties of the two targeted mechanisms in energy-related applications such as the photocatalytic generation of hydrogen and open the door to wavelength-selective photocatalysis and novel tandem reactions.

Rational synthesis of novel "giant" CuInTeSe/CdS core/shell quantum dots for optoelectronics.

"Giant" core/shell quantum dots (g-QDs) are promising candidates for emerging optoelectronic technologies thanks to their facile structure/composition-tunable optoelectronic properties and outstanding photo-physical/chemical stability. Here, we synthesized a new type of CuInTeSe (CITS)/CdS g-QDs and regulated their optoelectronic properties by controlling the shell thickness. Through increasing the shell thickness, as-prepared g-QDs exhibited tunable red-shifted emission (from 900 to 1200 nm) and prolonged photoluminescence (PL) lifetimes (up to ∼14.0 µs), indicating a formed band structure showing efficient charge separation and transfer, which is further testified by theoretical calculations and ultrafast time-resolved transient absorption (TA) spectroscopy. These CITS/CdS g-QDs with various shell thicknesses can be employed to fabricate photoelectrochemical (PEC) cells, exhibiting improved photoresponse and stability as compared to the bare CITS QD-based devices. The results indicate that the rational design and engineering of g-QDs is very promising for future QD-based optoelectronic technologies.