Single mandibular implant study - impact on dietary habits after 5 years of observation in patients with immediate and delayed loading protocols.

OBJECTIVES: Single midline implants in the edentulous mandible can be used to support existing complete dentures to improve patients' satisfaction and masticatory efficiency. The impact on patients' dietary habits and the influence of the loading protocol of the implants was the subject of this study. MATERIALS AND METHODS: In this prospective randomized clinical trial, edentulous patients with existing complete dentures in both jaws were treated with a single midline implant in the mandible. In group A, the implants were loaded immediately, in group B the loading was delayed after three months. Patients were asked to report on their nutritional intake before implant placement and 12, 24 and 60 months after loading using a standardized two-part questionnaire. RESULTS: Nutritional intake regarding the frequency of consumption of the requested food items did not change significantly during the 60-months study period, regardless of the loading protocol. In contrast, the second part of the questionnaire revealed that after 60 months, there was a significant decrease in avoidance of food, that had a coarse and hard texture in both groups. This significant decrease was observable in the group A in the first 12 and 24 months and in the group B after 60 months. CONCLUSION: A change in the patients' dietary habits due to the insertion of a single midline implant in the mandible to support the existing complete denture cannot be observed, independently to the loading protocol. CLINICAL RELEVANCE: Improving the chewing efficiency by single midline implants in the edentulous mandible does not lead to a change in dietary habits.

Influence of the Composition of Provisional Luting Materials on the Bond Strength of Temporary Single-Tooth Crowns on Titanium Abutments.

In addition to zinc oxide-based cements, resin-based materials are also available for temporary cementation. The aim of this in vitro study was to determine the influence of the different material compositions on temporary bonds. In nine test series (n = 30), temporary bis-acrylate single-tooth crowns were bonded onto prefabricated titanium abutments with nine different temporary luting materials. After simulating an initial (24 h, distilled water, 37 °C), a short-term (7 days, distilled water, 37 °C) and a long-term provisional restoration period (12h, distilled water, 37 °C; thermocycling: 5000 cycles) in subgroups (n = 10), the bond strength was examined using a combined tensile-shear test. Statistical analysis was performed by univariate analysis of variance or a non-parametric Kruskal-Wallis test, followed by post hoc tests. Of the three resin-based materials, two showed significantly higher bond strength values compared to all other materials (p < 0.001), regardless of the storage procedure. The resin-based materials were followed by eugenol-free and eugenol-containing zinc oxide materials. Significant intragroup differences were observed between the composite-based materials after all storage periods. This was only observed for some of the zinc oxide-based materials. The results show that under in vitro conditions, not only the composition of the temporary luting materials but also the different storage conditions have a significant influence on temporary bonds.

Digital Evaluation of Vertical Ridge Augmentation with the Modified Shell Technique Using a Xenogeneic Bone Lamina: A Case Series.

Vertical ridge augmentation is a demanding and technique-sensitive surgical procedure. In the present case series, cone beam CT (CBCT) scans from the clinical routine of patients treated using a novel approach for vertical bone augmentation were assessed. All patients showed a single-tooth class 5 defect and were treated using a modification of the original shell technique. Cortical bone plates were replaced with a lamina composed of a partially demineralized porcine xenograft. CBCT scans of six consecutive patients were treated with the lamina and particulate bone from the mandibular ramus prior to a single tooth implant in the anterior maxilla were included. Pre- and postsurgical CBCT data sets were superimposed and analyzed digitally using surface matching and Boolean subtraction. The volume of the grafted area was calculated with and without the xenograft. The vertical gain of the ridge height measured in this case series varied from 7 to 11.3 mm. The mean vertical gain was 8.97 mm. The mean volume including the xenograft was 382.59 mm3 (SD 73.39) and 250.84 mm3 (SD 53.67) without the lamina. The modified shell technique used in this case series for the vertical augmentation of single-tooth class 5 defects provided sufficient bone for single implant restorations.