Dynamic Material Flow Analysis of PET, PE, and PP Flows in Europe: Evaluation of the Potential for Circular Economy.

This study evaluates the potential circularity of PET, PE, and PP flows in Europe based on dynamic material flow analysis (MFA), considering product lifetimes, demand growth rates, and quality reductions of recycled plastic (downcycling). The circularity was evaluated on a baseline scenario, representing 2016 conditions, and on prospective scenarios representing key circularity enhancing initiatives, including (i) maintaining constant plastic consumption, (ii) managing waste plastic exports in the EU, (iii) design-for-recycling initiatives, (iv) improved collection, and (v) improved recovery and reprocessing. Low recycling rates (RR, 13-20%) and dependence on virgin plastic, representing 85-90% of the annual plastic demand, were demonstrated after 50 years in the baseline. Limited improvements were related to the individual scenarios, insufficient to meet existing recycling targets. However, by combining initiatives, RRs above 55%, where 75-90% was recycled in a closed loop, were demonstrated. Moreover, 40-65% of the annual demand could potentially be covered by recycled plastic. Maintaining a constant plastic demand over time was crucial in order to reduce the absolute dependence on virgin plastic, which was not reflected by the RR. Thus, focusing strictly on RRs and even whether and to which extent virgin material is substituted, is insufficient for evaluating the transition toward circularity, which cannot be achieved by technology improvements alone-the demand must also be stabilized.

Temporal and geographical patterns of solid waste collected at recycling centres.

Citizens increasingly dispose their waste at household waste recycling centres (HWRC). To enhance the collection of recyclables materials, local authorities and waste management companies invest considerable resources in planning. While the planning of these centres requires a comprehensive understanding of collected solid waste, only limited studies have consistently investigated waste data from HWRC. To fill this knowledge gap, historical data for HWRC from the Greater Copenhagen, Central Zealand, Silkeborg and Djursland in Denmark were analysed with regards to temporal and geographical variation. The results showed the mass of collected waste varies seasonally; this trend was consistently seen during the period 2010-2016. Moreover, the data revealed that the total waste collected was principally driven by the number of visitors. The geometric bar plot and ternary plot depicted an increase in the percentage of recyclable materials, whereas the percentage of incinerated waste decreased during the period 2010-2016. The waste characterisation study indicated that about 7% of small miscellaneous combustible waste was brought in black plastic bag, although these bags were forbidden; the results suggest that the percentage of misplaced recyclable materials could considerably decrease if citizens bring their waste in clear plastic bags.

Meeting the Needs for Released Nanomaterials Required for Further Testing-The SUN Approach.

The analysis of the potential risks of engineered nanomaterials (ENM) has so far been almost exclusively focused on the pristine, as-produced particles. However, when considering a life-cycle perspective, it is clear that ENM released from genuine products during manufacturing, use, and disposal is far more relevant. Research on the release of materials from nanoproducts is growing and the next necessary step is to investigate the behavior and effects of these released materials in the environment and on humans. Therefore, sufficient amounts of released materials need to be available for further testing. In addition, ENM-free reference materials are needed since many processes not only release ENM but also nanosized fragments from the ENM-containing matrix that may interfere with further tests. The SUN consortium (Project on "Sustainable Nanotechnologies", EU seventh Framework funding) uses methods to characterize and quantify nanomaterials released from composite samples that are exposed to environmental stressors. Here we describe an approach to provide materials in hundreds of gram quantities mimicking actual released materials from coatings and polymer nanocomposites by producing what is called "fragmented products" (FP). These FP can further be exposed to environmental conditions (e.g., humidity, light) to produce "weathered fragmented products" (WFP) or can be subjected to a further size fractionation to isolate "sieved fragmented products" (SFP) that are representative for inhalation studies. In this perspective we describe the approach, and the used methods to obtain released materials in amounts large enough to be suitable for further fate and (eco)toxicity testing. We present a case study (nanoparticulate organic pigment in polypropylene) to show exemplarily the procedures used to produce the FP. We present some characterization data of the FP and discuss critically the further potential and the usefulness of the approach we developed.

Life cycle assessment of resource recovery from municipal solid waste incineration bottom ash.

Bottom ash, the main solid output from municipal solid waste incineration (MSWI), has significant potential for the recovery of resources such as scrap metals and aggregates. The utilisation of these resources ideally enables natural resources to be saved. However, the quality of the recovered scrap metals may limit recycling potential, and the utilisation of aggregates may cause the release of toxic substances into the natural environment through leaching. A life cycle assessment (LCA) was applied to a full-scale MSWI bottom ash management and recovery system to identify environmental breakeven points beyond which the burdens of the recovery processes outweigh the environmental benefits from valorising metals and mineral aggregates. Experimental data for the quantity and quality of individual material fractions were used as a basis for LCA modelling. For the aggregates, three disposal routes were compared: landfilling, road sub-base and aggregate in concrete, while specific leaching data were used as the basis for evaluating toxic impacts. The recovery and recycling of aluminium, ferrous, stainless steel and copper scrap were considered, and the importance of aluminium scrap quality, choice of marginal energy technologies and substitution rates between primary and secondary aluminium, stainless steel and ferrous products, were assessed and discussed. The modelling resulted in burdens to toxic impacts associated with metal recycling and leaching from aggregates during utilisation, while large savings were obtained in terms of non-toxic impacts. However, by varying the substitution rate for aluminium recycling between 0.35 and 0.05 (on the basis of aluminium scrap and secondary aluminium alloy market value), it was found that the current recovery system might reach a breakeven point between the benefits of recycling and energy expended on sorting and upgrading the scrap.

Life cycle assessment of waste incineration in Denmark and Italy using two LCA models.

In Europe, about 20% of municipal solid waste is incinerated. Large differences can be found between northern and southern Europe regarding energy recovery efficiencies, flue gas cleaning technologies and residue management. Life-cycle assessment (LCA) of waste incineration often provides contradictory results if these local conditions are not properly accounted for. The importance of regional differences and site-specific data, and choice of LCA model itself, was evaluated by assessment of two waste incinerators representing northern and southern Europe (Denmark and Italy) based on two different LCA models (SimaPro and EASEWASTE). The results showed that assumptions and modelling approaches regarding energy recovery/substitution and direct air emissions were most critical. Differences in model design and model databases mainly had consequences for the toxicity-related impact categories. The overall environmental performance of the Danish system was better than the Italian, mainly because of higher heat recovery at the Danish plant. Flue gas cleaning at the Italian plant was, however, preferable to the Danish, indicating that efficient flue gas cleaning may provide significant benefits. Differences in waste composition between the two countries mainly affected global warming and human toxicity via water. Overall, SimaPro and EASEWASTE provided consistent ranking of the individual scenarios. However, important differences in results from the two models were related to differences in the databases and modelling approaches, in particular the possibility for modelling of waste-specific emissions affected the toxicity-related impact categories. The results clearly showed that the use of site-specific data was essential for the results.

An environmental and economic assessment of bioplastic from urban biowaste. The example of polyhydroxyalkanoate.

Bio-based and biodegradable plastics promise considerable reductions in our dependency on fossil fuels and in the environmental impacts of plastic waste. This study quantifies the environmental and economic consequences of diverting municipal food waste and wastewater sewage sludge from traditional management to the biorefinery-based production of polyhydroxyalkanoates (PHA) in five geographical regions. The results show that PHA can outperform fossil polyurethane and PHA from first-generation biomass (sugarcane and maize) with respect to both environmental impacts and societal costs (four times lower impacts and eight times lower costs than polyurethane). To outperform other fossil polymers like low-density polyethylene (LDPE), biorefinery performance should be improved further by more efficient utilization of sodium hypochlorite during PHA extraction, minimization of methane leakage in biogas facilities, upgrading of biogas to biomethane, and more effective handling of the liquid fraction from digestate dewatering.

Quantification of greenhouse gas emissions from windrow composting of garden waste.

Microbial degradation of organic wastes entails the production of various gases such as carbon dioxide (CO(2)), methane (CH(4)), nitrous oxide (N(2)O), and carbon monoxide (CO). Some of these gases are classified as greenhouse gases (GHGs), thus contributing to climate change. A study was performed to evaluate three methods for quantifying GHG emissions from central composting of garden waste. Two small-scale methods were used at a windrow composting facility: a static flux chamber method and a funnel method. Mass balance calculations based on measurements of the C content in the in- and out-going material showed that 91 to 94% of the C could not be accounted for using the small-scale methods, thereby indicating that these methods significantly underestimate GHG emissions. A dynamic plume method (total emission method) employing Fourier Transform Infra Red (FTIR) absorption spectroscopy was found to give a more accurate estimate of the GHG emissions, with CO(2) emissions measured to be 127 +/- 15% of the degraded C. Additionally, with this method, 2.7 +/- 0.6% and 0.34 +/- 0.16% of the degraded C was determined to be emitted as CH(4) and CO. In this study, the dynamic plume method was a more effective tool for accounting for C losses and, therefore, we believe that the method is suitable for measuring GHG emissions from composting facilities. The total emissions were found to be 2.4 +/- 0.5 kg CH(4)-C Mg(-1) wet waste (ww) and 0.06 +/- 0.03 kg N(2)O-N Mg(-1) ww from a facility treating 15,540 Mg of garden waste yr(-1), or 111 +/- 30 kg CO(2)-equivalents Mg(-1) ww.

Mass balances and life-cycle inventory for a garden waste windrow composting plant (Aarhus, Denmark).

A comprehensive life-cycle inventory of all consumptions and emissions of environmental relevance was made for the windrow composting plant treating garden waste in Aarhus (Denmark). The flows of materials and substances within the facility were balanced using the mass-balance model STAN. The overall fuel and electricity use at the facility (3.04 L diesel Mg(-1) wet waste (ww) and 0.2 k Wh Mg(-1) ww) was low whereas the emissions of CH( 4) and N(2)O from the windrows (2.4 ± 0.5 kg CH( 4)-C Mg(-1) ww and 0.06 ± 0.03 kg N(2)O-N Mg(-1) ww) were relatively high compared to data reported in similar studies. The loss of carbon during the 14-month-long composting was 56%. CH(4) made up 2.1% of the C lost. Loss of nitrogen-containing compounds was identified as the most sensible and uncertain parameter and could be relevant for global warming (N(2)O emissions), acidification (NH(3) emissions), and eutrophication (NH(3) and NO(3) emissions). The compost produced had a very low content of heavy metals and was suitable for use in gardens and/or agriculture.

Anaerobic digestion and digestate use: accounting of greenhouse gases and global warming contribution.

Anaerobic digestion (AD) of source-separated municipal solid waste (MSW) and use of the digestate is presented from a global warming (GW) point of view by providing ranges of greenhouse gas (GHG) emissions that are useful for calculation of global warming factors (GWFs), i.e. the contribution to GW measured in CO(2)-equivalents per tonne of wet waste. The GHG accounting was done by distinguishing between direct contributions at the AD facility and indirect upstream or downstream contributions. GHG accounting for a generic AD facility with either biogas utilization at the facility or upgrading of the gas for vehicle fuel resulted in a GWF from -375 (a saving) to 111 (a load) kg CO(2)-eq. tonne(-1) wet waste. In both cases the digestate was used for fertilizer substitution. This large range was a result of the variation found for a number of key parameters: energy substitution by biogas, N(2)O-emission from digestate in soil, fugitive emission of CH( 4), unburned CH(4), carbon bound in soil and fertilizer substitution. GWF for a specific type of AD facility was in the range -95 to -4 kg CO(2)-eq. tonne(-1) wet waste. The ranges of uncertainty, especially of fugitive losses of CH(4) and carbon sequestration highly influenced the result. In comparison with the few published GWFs for AD, the range of our data was much larger demonstrating the need to use a consistent and robust approach to GHG accounting and simultaneously accept that some key parameters are highly uncertain.

Composting and compost utilization: accounting of greenhouse gases and global warming contributions.

Greenhouse gas (GHG) emissions related to composting of organic waste and the use of compost were assessed from a waste management perspective. The GHG accounting for composting includes use of electricity and fuels, emissions of methane and nitrous oxide from the composting process, and savings obtained by the use of the compost. The GHG account depends on waste type and composition (kitchen organics, garden waste), technology type (open systems, closed systems, home composting), the efficiency of off-gas cleaning at enclosed composting systems, and the use of the compost. The latter is an important issue and is related to the long-term binding of carbon in the soil, to related effects in terms of soil improvement and to what the compost substitutes; this could be fertilizer and peat for soil improvement or for growth media production. The overall global warming factor (GWF) for composting therefore varies between significant savings (-900 kg CO(2)-equivalents tonne(-1) wet waste (ww)) and a net load (300 kg CO(2)-equivalents tonne( -1) ww). The major savings are obtained by use of compost as a substitute for peat in the production of growth media. However, it may be difficult for a specific composting plant to document how the compost is used and what it actually substitutes for. Two cases representing various technologies were assessed showing how GHG accounting can be done when specific information and data are available.

C balance, carbon dioxide emissions and global warming potentials in LCA-modelling of waste management systems.

Global warming potential (GWP) is an important impact category in life-cycle-assessment modelling of waste management systems. However, accounting of biogenic CO(2) emissions and sequestered biogenic carbon in landfills and in soils, amended with compost, is carried out in different ways in reported studies. A simplified model of carbon flows is presented for the waste management system and the surrounding industries, represented by the pulp and paper manufacturing industry, the forestry industry and the energy industry. The model calculated the load of C to the atmosphere, under ideal conditions, for 14 different waste management scenarios under a range of system boundary conditions and a constant consumption of C-product (here assumed to be paper) and energy production within the combined system. Five sets of criteria for assigning GWP indices to waste management systems were applied to the same 14 scenarios and tested for their ability to rank the waste management alternatives reflecting the resulting CO(2) load to the atmosphere. Two complete criteria sets were identified yielding fully consistent results; one set considers biogenic CO(2) as neutral, the other one did not. The results showed that criteria for assigning global warming contributions are partly linked to the system boundary conditions. While the boundary to the paper industry and the energy industry usually is specified in LCA studies, the boundary to the forestry industry and the interaction between forestry and the energy industry should also be specified and accounted for.

Resource quality of wood waste: The importance of physical and chemical impurities in wood waste for recycling.

Recycling of post-consumer wood waste into particleboard may be hindered by the presence of physical and chemical impurities in the waste stream, therefore calling for increased attention on the quality of wood waste. However, wood waste comprises several uses/types of wood, along with different levels of contamination. This study provides the detailed sampling and characterisation of wood waste according to its source, type and resource quality grade. Eight tonnes of wood waste, intended for recycling and collected at three Danish recycling centres, were subdivided into 34 individual material fractions and characterised with respect to the presence of three classes of physical impurities (misplacements, interfering materials and low-quality wood waste) as well as chemical concentrations of more than hundred chemical elements and persistent organic pollutants (POPs). The results demonstrated that contaminant and concentration levels vary significantly according to wood waste type and source, thus emphasising that wood waste should not be viewed as a single material flow but rather be understood and managed according to the presence of individual fractions. Including only clean wood waste fractions at the three recycling centres, 41-87% of the collected wood waste per weight could be recycled - the rest being physical impurities. The results showed that chemical contamination was significantly higher for low-quality wood waste, thus clearly indicating that improvements in separate collection, sorting and handling of wood waste may improve the resource quality of wood waste and potentially achieve cleaner recycling practices.

Combustible waste collected at Danish recycling centres: Characterisation, recycling potentials and contribution to environmental savings.

Europe is currently adapting its waste management strategies towards the increased recycling of waste materials, motivated by ambitious recycling targets. This requires correctly sorting and recovering of all relevant waste flows. In Denmark, a considerable share of residential household waste is collected at recycling centres, 16% of which is sent to energy recovery in the form of "small combustible waste". Although essential in order to enhance the management of household waste, very little information exists on its composition. In this study, 25 tonnes of small combustible waste were sampled from eight Danish recycling centres and classified according to material fraction, application and physical properties. On this basis, the potential contribution to the overall recycling rate was evaluated together with estimation of the potential environmental savings associated with recycling of these fractions. Less than half of the sampled waste comprised combustible materials, whereas recyclable fractions accounted for 47-64%, mainly including textiles, plastics and paper waste. Assuming this composition applicable to the national level, recycling these waste materials collected as small combustibles increased national recycling rates for households by 12%, calculated as waste received at recycling processes. Moreover, the potential climate change savings associated with recycling of Danish household waste increased by 30% compared to the current level. Plastics, textiles and paper were the main contributors to this increase, suggesting that improved sorting practices for these materials should be prioritised. The study demonstrates that detailed compositional data for waste materials has paramount importance when estimating recycling potentials and quantifying the associated environmental benefits.

Microbial population dynamics in urban organic waste anaerobic co-digestion with mixed sludge during a change in feedstock composition and different hydraulic retention times.

Microbial communities play an essential role in the biochemical pathways of anaerobic digestion processes. The correlations between microorganisms' relative abundance and anaerobic digestion process parameters were investigated, by considering the effect of different feedstock compositions and hydraulic retention times (HRTs). Shifts in microbial diversity and changes in microbial community richness were observed by changing feedstock composition from mono-digestion of mixed sludge to co-digestion of food waste, grass clippings and garden waste with mixed sludge at HRT of 30, 20, 15 and 10 days. Syntrophic acetate oxidation along with hydrogenotrophic methanogenesis, mediated by Methanothermobacter, was found to be the most prevalent methane formation pathway, with the only exception of 10 days' HRT, in which Methanosarcina was the most dominant archaea. Significantly, the degradation of complex organic polymers was found to be the most active process, performed by members of S1 (Thermotogales), Thermonema and Lactobacillus in a reactor fed with a high share of food waste. Conversely, Thermacetogenium, Anaerobaculum, Ruminococcaceae, Porphyromonadaceae and the lignocellulosic-degrading Clostridium were the significantly more abundant bacteria in the reactor fed with an increased share of lignocellulosic biomass in the form of grass clippings and garden waste. Finally, microbes belonging to Coprothermobacter, Syntrophomonas and Clostridium were correlated significantly with the specific methane yield obtained in both reactors.

From macro- to microplastics - Analysis of EU regulation along the life cycle of plastic bags.

Plastic pollution and its environmental effects has received global attention the recent years. However, limited attention has so far been directed towards how plastics are regulated in a life cycle perspective and how regulatory gaps can be addressed in order to limit and prevent environmental exposure and hazards of macro- and microplastics. In this paper, we map European regulation taking outset in the life cycle perspective of plastic carrier bags: from plastic bag production to when it enters the environment. Relevant regulatory frameworks, directives and authorities along the life cycle are identified and their role in regulation of plastics is discussed. Most important regulations were identified as: the EU chemical Regulation, the Packaging and Packaging Waste Directive including the amending Directive regarding regulation of the consumption of lightweight plastic carrier bags, the Waste Framework Directive and the Directive on the Landfill of Waste. The main gaps identified relate to lack of clear definitions of categories of polymers, unambitious recycling rates and lack of consideration of macro- and microplastics in key pieces of legislation. We recommend that polymers are categorized according to whether they are polymers with the same monomer constituents (homopolymers) or with different monomer constituents (copolymers) and that polymers are no longer exempt from registration and evaluation under REACH. Plastics should furthermore have the same high level of monitoring and reporting requirements as hazardous waste involving stricter requirements to labelling, recordkeeping, monitoring and control over the whole lifecycle. Finally, we recommend that more ambitious recycle and recovery targets are set across the EU. Regulation of the consumption of lightweight plastic carrier bags should also apply to heavyweight plastic carrier bags. Last, the Marine and Water Framework Directives should specifically address plastic waste affecting water quality.

Physico-chemical characterisation of material fractions in household waste: Overview of data in literature.

State-of-the-art environmental assessment of waste management systems rely on data for the physico-chemical composition of individual material fractions comprising the waste in question. To derive the necessary inventory data for different scopes and systems, literature data from different sources and backgrounds are consulted and combined. This study provides an overview of physico-chemical waste characterisation data for individual waste material fractions available in literature and thereby aims to support the selection of data fitting to a specific scope and the selection of uncertainty ranges related to the data selection from literature. Overall, 97 publications were reviewed with respect to employed characterisation method, regional origin of the waste, number of investigated parameters and material fractions and other qualitative aspects. Descriptive statistical analysis of the reported physico-chemical waste composition data was performed to derive value ranges and data distributions for element concentrations (e.g. Cd content) and physical parameters (e.g. heating value). Based on 11,886 individual data entries, median values and percentiles for 47 parameters in 11 individual waste fractions are presented. Exceptional values and publications are identified and discussed. Detailed datasets are attached to this study, allowing further analysis and new applications of the data.

Semi-quantitative analysis of solid waste flows from nano-enabled consumer products in Europe, Denmark and the United Kingdom - Abundance, distribution and management.

Many nano-enabled consumer products are known to be in the global market. At the same, little is known about the quantity, type, location etc. of the engineered nanomaterials (ENMs) inside the products. This limits the scientific investigations of potential environmental effects of these materials, and especially the knowledge of ENM behaviour and potential effects at the end-of-life stage of the products is scarce. To gain a better understanding of the end-of-life waste treatment of nano-enabled consumer product, we provide an overview of the ENMs flowing into and throughout waste systems in Europe, Denmark and the United Kingdom. Using a nanoproduct inventory (nanodb.dk), we performed a four-step analysis to estimate the most abundant ENMs and in which waste fractions they are present. We found that in terms of number of products: (i) nano silver is the most used ENM in consumer products, and (ii) plastic from used product containers is the largest waste fraction also comprising a large variety of ENMs, though possibly in very small masses. Also, we showed that the local waste management system can influence the distribution of ENMs. It is recommended that future research focus on recycling and landfilling of nano-enabled products since these compartments represent hot spots for end-of-life nanoproducts.

Life cycle assessment of thermal waste-to-energy technologies: review and recommendations.

Life cycle assessment (LCA) has been used extensively within the recent decade to evaluate the environmental performance of thermal Waste-to-Energy (WtE) technologies: incineration, co-combustion, pyrolysis and gasification. A critical review was carried out involving 250 individual case-studies published in 136 peer-reviewed journal articles within 1995 and 2013. The studies were evaluated with respect to critical aspects such as: (i) goal and scope definitions (e.g. functional units, system boundaries, temporal and geographic scopes), (ii) detailed technology parameters (e.g. related to waste composition, technology, gas cleaning, energy recovery, residue management, and inventory data), and (iii) modeling principles (e.g. energy/mass calculation principles, energy substitution, inclusion of capital goods and uncertainty evaluation). Very few of the published studies provided full and transparent descriptions of all these aspects, in many cases preventing an evaluation of the validity of results, and limiting applicability of data and results in other contexts. The review clearly suggests that the quality of LCA studies of WtE technologies and systems including energy recovery can be significantly improved. Based on the review, a detailed overview of assumptions and modeling choices in existing literature is provided in conjunction with practical recommendations for state-of-the-art LCA of Waste-to-Energy.

Source segregation of food waste in office areas: Factors affecting waste generation rates and quality.

Existing legislation mandates that the amount of waste being recycled should be increased. Among others, in its Resource Strategy Plan, the Danish Government decided that at least 60% of food waste generated by the service sector, including in office areas, should be source-sorted and collected separately by 2018. To assess the achievability of these targets, source-sorted food waste and residual waste from office areas was collected and weighed on a daily basis during 133 working days. Waste composition analyses were conducted every week to investigate the efficiency of the source-sorting campaign and the purity of the source-sorted food waste. The moisture content of source-sorted food waste and residual waste fractions, and potential methane production from source-sorted food waste, was also investigated. Food waste generation equated to 23 ± 5 kg/employee/year, of which 20 ± 5 kg/employee/year was source-sorted, with a considerably high purity of 99%. Residual waste amounted to 10 ± 5 kg/employee/year and consisted mainly of paper (29 ± 13%), plastic (23 ± 9%) and missorted food waste (24 ± 16%). The moisture content of source-sorted food waste was significantly higher (8%) than missorted food waste, and the methane potential of source-sorted food waste was 463 ± 42 mL CH4/g VS. These results show that food waste in office areas offers promising potential for relatively easily collectable and pure source-sorted food waste, suggesting that recycling targets for food waste could be achieved with reasonable logistical ease in office areas.