Monolithically integrated 940†nm VCSELs on bulk Ge substrates.

This research successfully developed an independent Ge-based VCSEL epitaxy and fabrication technology route, which set the stage for integrating AlGaAs-based semiconductor devices on bulk Ge substrates. This is the second successful Ge-based VCSEL technology reported worldwide and the first Ge-based VCSEL technology with key details disclosed, including Ge substrate specification, transition layer structure and composition, and fabrication process. Compared with the GaAs counterparts, after epitaxy optimization, the Ge-based VCSEL wafer has a 40% lower surface root-mean-square roughness and 72% lower average bow-warp. After device fabrication, the Ge-based VCSEL has a 10% lower threshold current density and 19% higher maximum optical differential efficiency than the GaAs-based VCSEL.

26.5625 Gbaud PAM-4 short-reach transmission at 75°C using 850 nm VCSELs with strategic oxide guiding layer positioning.

This article presents an all-epitaxy approach to reduce the root mean square spectral width (ΔλR M S) of 850 nm oxide-confined vertical cavity surface-emitting lasers (VCSELs) with a large aperture of 7 µm through strategic optimization of the oxide guiding layer within the epitaxy structure. At 75°C, the VCSEL demonstrates a ΔλR M S of ∼0.3 nm at a bias current of 7.5 mA. Furthermore, the VCSEL achieves successful transmission of 26.5625 Gbaud PAM-4 modulation over a short-reach (SR) OM4 fiber link while maintaining a TDECQ budget below the 4.5 dB specified by 50G IEEE Ethernet standards.

25 Gb/s NRZ transmission at 85°C using a high-speed 940 nm AlGaAs oxide-confined VCSEL grown on a Ge substrate.

In this Letter, we present a comprehensive analysis of the high-speed performance of 940 nm oxide-confined AlGaAs vertical-cavity surface-emitting lasers (VCSELs) grown on Ge substrates. Our demonstration reveals a pronounced superiority of Ge-based VCSELs in terms of thermal stability. The presented Ge-VCSEL has a maximum modulation bandwidth of 16.1 GHz and successfully realizes a 25 Gb/s NRZ transmission at 85 ∘C. The experimental results underscore the significance and potential of Ge-VCSELs for applications requiring robust performance in high-temperature environments, laying the cornerstone for the future development of VCSEL devices.

Microplastics in marine ecosystems: A comprehensive review of biological and ecological implications and its mitigation approach using nanotechnology for the sustainable environment.

Microplastic contamination has rapidly become a serious environmental issue, threatening marine ecosystems and human health. This review aims to not only understand the distribution, impacts, and transfer mechanisms of microplastic contamination but also to explore potential solutions for mitigating its widespread impact. This review encompasses the categorisation, origins, and worldwide prevalence of microplastics and methodically navigates the complicated structure of microplastics. Understanding the sources of minute plastic particles infiltrating water bodies worldwide is critical for successful removal. The presence and accumulation of microplastics has far reaching negative impacts on various marine creatures, eventually extending its implications to human health. Microplastics are known to affect the metabolic activities and the survival of microbial communities, phytoplankton, zooplankton, and fauna present in marine environments. Moreover, these microplastics cause developmental abnormalities, endocrine disruption, and several metabolic disorders in humans. These microplastics accumulates in aquatic environments through trophic transfer mechanisms and biomagnification, thereby disrupting the delicate balance of these ecosystems. The review also addresses the tactics for minimising the widespread impact of microplastics by suggesting practical alternatives. These include increasing public awareness, fostering international cooperation, developing novel cleanup solutions, and encouraging the use of environment-friendly materials. In conclusion, this review examines the sources and prevalence of microplastic contamination in marine environment, its impacts on living organisms and ecosystems. It also proposes various sustainable strategies to mitigate the problem of microplastics pollution. Also, the current challenges associated with the mitigation of these pollutants have been discussed and addressing these challenges require immediate and collective action for restoring the balance in marine ecosystems.

Optimizing bone and biomass co-torrefaction parameters: High-performance arsenic removal from wastewater via co-torrefied bone char.

This study aimed to investigate bone char's physicochemical transformations through co-torrefaction and co-pyrolysis processes with biomass. Additionally, it aimed to analyze the carbon sequestration process during co-torrefaction of bone and biomass and optimize the process parameters of co-torrefaction. Finally, the study sought to evaluate the arsenic sorption capacity of both torrefied and co-torrefied bone char. Bone and biomass co-torrefaction was conducted at 175 °C-300 °C. An orthogonal array of Taguchi techniques and artificial neural networks (ANN) were employed to investigate the influence of various torrefaction parameters on carbon dioxide sequestration within torrefied bone char. A co-torrefied bone char, torrefied at a reaction temperature of 300 °C, a heating rate of 15 °C·min-1, and mixed with 5 g m of biomass (wood dust), was selected for the arsenic (III) sorption experiment due to its elevated carbonate content. The results revealed a higher carbonate fraction (21%) in co-torrefied bone char at 300 °C compared to co-pyrolyzed bone char (500-700 °C). Taguchi and artificial neural network (ANN) analyses indicated that the relative impact of process factors on carbonate substitution in bone char followed the order of co-torrefaction temperature (38.8%) > heating rate (31.06%) > addition of wood biomass (30.1%). Co-torrefied bone chars at 300 °C exhibited a sorption capacity of approximately 3 mg g-1, surpassing values observed for pyrolyzed bone chars at 900 °C in the literature. The findings suggest that co-torrefied bone char could serve effectively as a sorbent in filters for wastewater treatment and potentially fulfill roles such as a remediation agent, pH stabilizer, or valuable source of biofertilizer in agricultural applications.

Coastal aquatic pollutants degradation using ZnCo2O4 nanorods.

Water pollution has caused problems in coastal areas, rivers, lakes, and other important water sources around the world as a result of inappropriate waste management. Meanwhile, these pollutants are harmful to humans and aquatic life. Textile dye effluent methyl orange (MO) was used in this work for dye degradation studies employing nanocomposites. As a result, the importance of synthesizing pure ZnO and Co3O4 nanoparticles with composites of ZnCo2O4 (zinc cobaltite) nanorods in three various proportions (90:10, 75:25, and 50:50) is emphasized in this study. Many advanced approaches were used to assess the various features of these materials, including size and shape. Fourier transform infrared (FT-IR) spectroscopy was used to determine the vibrational modes of the materials. The absorption measurements were then carried out using UV-vis spectroscopic techniques, and the photocatalytic breakdown of MO was done under visible light irradiation. The findings revealed that pure materials were inadequate for visible light activity, resulting in decreased degradation efficiencies. Spinel cobaltite structures have potential degradation efficiency under visible light, while ZnCo2O4 (50:50) catalyst has superior degradation efficiency of 59.8% over MO. The crystallite size, morphology, functional group, absorption wavelength, and band gap all play important roles in enhancing the material's photocatalytic activity under visible light. Meanwhile, ZnCo2O4 spinel structures are crucial for increasing charge carriers and reducing electron-hole recombination. As a result, zinc cobaltite minerals are widely used in industrial dye degradation applications.

KHCO3-activated high surface area biochar derived from brown algae: A case study for efficient adsorption of Cr(VI) in aqueous solution.

The current study aimed to assess the effectiveness of biochar formed from algae in the removal of Cr(VI) through the process of impregnating brown algae Sargassum hemiphyllum with KHCO3. The synthesis of KHCO3-activated biochar (KBAB-3), demonstrating remarkable adsorption capabilities for Cr(VI), was accomplished utilizing a mixture of brown algae and KHCO3 in a mass ratio of 1:3, followed by calcination at a temperature of 700 °C. Based on the empirical evidence, it can be observed that KBAB-3 shown a significant ability to adsorb Cr(VI) within a range of 60-160 mg g-1 across different environmental conditions. In addition, the KBAB-3 material demonstrated the advantageous characteristic of easy separation, allowing for the continued maintenance of a high efficiency in removing Cr(VI) even after undergoing numerous cycles of reuse. In conclusion, the application of KBAB-3, a novel adsorbent, exhibits considerable prospects for effective removal of Cr(VI) from diverse water sources in the near future.

Recent advances in liquid fuel production from plastic waste via pyrolysis: Emphasis on polyolefins and polystyrene.

The management of plastic waste (PW) has become an indispensable worldwide issue because of the enhanced accumulation and environmental impacts of these waste materials. Thermo-catalytic pyrolysis has been proposed as an emerging technology for the valorization of PW into value-added liquid fuels. This review provides a comprehensive investigation of the latest advances in thermo-catalytic pyrolysis of PW for liquid fuel generation, by emphasizing polyethylene, polypropylene, and polystyrene. To this end, the current strategies of PW management are summarized. The various parameters affecting the thermal pyrolysis of PW (e.g., temperature, residence time, heating rate, pyrolysis medium, and plastic type) are discussed, highlighting their significant influence on feed reactivity, product yield, and carbon number distribution of the pyrolysis process. Optimizing these parameters in the pyrolysis process can ensure highly efficient energy recovery from PW. In comparison with non-catalytic PW pyrolysis, catalytic pyrolysis of PW is considered by discussing mechanisms, reaction pathways, and the performance of various catalysts. It is established that the introduction of either acid or base catalysts shifts PW pyrolysis from the conventional free radical mechanism towards the carbonium ion mechanism, altering its kinetics and pathways. This review also provides an overview of PW pyrolysis practicality for scaling up by describing techno-economic challenges and opportunities, environmental considerations, and presenting future outlooks in this field. Overall, via investigation of the recent research findings, this paper offers valuable insights into the potential of thermo-catalytic pyrolysis as an emerging strategy for PW management and the production of liquid fuels, while also highlighting avenues for further exploration and development.

Boosting acetaminophen degradation in water by peracetic acid activation: A novel approach using chestnut shell-derived biochar at varied pyrolysis temperatures.

In this study, biochar derived from chestnut shells was synthesized through pyrolysis at varying temperatures from 300 °C to 900 °C. The study unveiled that the pyrolysis temperature is pivotal in defining the physical and chemical attributes of biochar, notably its adsorption capabilities and its role in activating peracetic acid (PAA) for the efficient removal of acetaminophen (APAP) from aquatic environments. Notably, the biochar processed at 900 °C, referred to as CN900, demonstrated an exceptional adsorption efficiency of 55.8 mg g-1, significantly outperforming its counterparts produced at lower temperatures (CN300, CN500, and CN700). This enhanced performance of CN900 is attributed to its increased surface area, improved micro-porosity, and a greater abundance of oxygen-containing functional groups, which are a consequence of the elevated pyrolysis temperature. These oxygen-rich functional groups, such as carbonyls, play a crucial role in facilitating the decomposition of the O-O bond in PAA, leading to the generation of reactive oxygen species (ROS) through electron transfer mechanisms. This investigation contributes to the development of sustainable and cost-effective materials for water purification, underscoring the potential of chestnut shell-derived biochar as an efficient adsorbent and catalyst for PAA activation, thereby offering a viable solution for environmental cleanup efforts.

Surgical Outcomes of Pancreatic Solid Pseudopapillary Neoplasm: Experiences of 24 Patients in a Single Institute.

Background and Objectives: The pancreatic solid pseudopapillary neoplasm (SPN), a rare tumor predominantly affecting young women, has seen an increased incidence due to improved imaging and epidemiological knowledge. This study aimed to understand the outcomes of different interventions, possible complications, and associated risk factors. Materials and Methods: This study retrospectively analyzed 24 patients who underwent pancreatic surgery for SPNs between September 1998 and July 2020. Results: Surgical intervention, typically required for symptomatic cases or pathological confirmation, yielded favorable outcomes with a 5-year survival rate of up to 97%. Despite challenges in standardizing preoperative evaluation and follow-up protocols, aggressive complete resection showed promising long-term survival and good oncological outcomes. Notably, no significant differences were found between conventional and minimally invasive (MI) surgery in perioperative outcomes. Histopathological correlations were lacking in prognosis and locations. Among the patients, one developed diffuse liver metastases 41 months postoperatively but responded well to chemotherapy and transcatheter arterial chemoembolization, with disease stability observed at 159 postoperative months. Another patient developed nonalcoholic steatohepatitis after surgery and underwent liver transplantation, succumbing to poor medication adherence 115 months after surgery. Conclusions: These findings underscore the importance of surgical intervention in managing SPNs and suggest the MI approach as a viable option with comparable outcomes to conventional surgery.

Progressive yield of nickel cobaltite nanocubes for visible light utilization and degrading activities of methyl orange dye pollutant.

In this study, pure cobalt oxide (Co3O4) as well as nickel cobaltite (NiCo2O4) were investigated with their capacity of degradation efficiency for textile dyes like methyl orange (MO) employing visible light irradiation. Two variable concentrations of nickel cobaltite (NiCo2O4) with 75:25 and 50:50 wt ratios along with the pure metal oxides were synthesized by thermal decomposition method and analyzed by various sophisticated instruments. Initially, the structural characteristics described the fine crystalline nature of NiCo2O4 and also exhibits reduced size than the pure component material (Co3O4). Besides, NiCo2O4 catalysts represented nano cubic shaped particles, and also their coordinating functional groups were evaluated. Further, the absorption wavelength confirms the two band positions of NiCo2O4 which leads to promote visible light absorption, and degrading efficiency of about 47.5% for NiCo2O4 (75:25) sample compared with NiCo2O4 (50:50) which produced only 26.3% degradation. This higher efficiency of the former was due to high crystallinity and interfacial charge transfer of combined Ni2+, Ni3+, Co2+ and Co3+ redox couples. This consecutively produces effective OH radicals that brought the degradation effectively under visible light. The recycling capacity up to 5 repeated cycles has been studied with the NiCo2O4 (75:25) and therefore the catalyst can further be used in other dye degradation.

Tetracycline-adsorbed biochar for solid biofuel usage to achieve waste utilization for environmental sustainability.

Biochar is widely used to remove organic pollutants from the environment. Several studies have focused on pollutant removal via biochar adsorption. However, research on the subsequent processing of pollutant-adsorbed biochar is lacking. This study explored the potential of biochar for the adsorption of an aquatic organic pollutant (tetracycline) and its subsequent use as a solid biofuel. These results suggest that corn straw-derived biochar (torrefaction and pyrolysis) is suitable for two-stage utilization to achieve bioresource valorization for environmental sustainability. Tetracycline-adsorbed biochar, particularly biochar pyrolyzed at 600 °C, is suitable for use as a biofuel. The biochar produced via torrefaction (300 °C) and pyrolysis (600 °C) is the optimal choice, with surface area, contact angle, graphitization degree, calorific value, enhancement factor, and upgrading energy index values of 172.48 m2/g, 120.4°, 3.87, 26.983 MJ/kg, 1.58, and 33.72, respectively. This is supported by the results of expense calculation, comprehensive performance analysis, and life-cycle assessment. Overall, the biochar produced in this study is suitable for organic pollutant removal and as solid biofuel; thus, it can be used to realize waste utilization for environmental sustainability.

Environmental benefits from the use of CO2 in the thermal disposal of cigarette butts.

As the global consumption of cigarettes has increased, the massive generation of cigarette butts (CBs) has led to critical environmental and health problems. Landfilling or incineration of CBs has been conventionally carried out, but such disposal protocols have suffered from the potential risks of the unwanted/uncontrolled release of leachates, carcinogens, and toxic chemicals into all environmental media. Thus, this study focuses on developing an environmentally dependable method for CB disposal. Littered CBs from filtered/electronic cigarettes were valorized into syngas (H2/CO). To seek a greener approach for the valorization of CBs, CO2 was intentionally considered as a reaction intermediate. Prior to multiple pyrolysis studies, the toxic chemicals in the CBs were qualitatively determined. This study experimentally proved that the toxic chemicals in CBs were detoxified/valorized into syngas. Furthermore, this work demonstrated that CO2 was effective in thermally destroying toxic chemicals in CBs via a gas-phase reaction. The reaction features and CO2 synergistically enhance syngas production. With the use of a supported Ni catalyst and CO2, syngas production from the catalytic pyrolysis of CBs was greatly enhanced (approximately 4 times). Finally, the gas-phase reaction by CO2 was reliably maintained owing to the synergistic mechanistic/reaction feature of CO2 for coke formation prevention on the catalyst surface.

Mesoporous NiO/Ni2O3 nanoflowers for favorable visible light photocatalytic degradation of 4-chlorophenol.

The present study highlights the treatment of industrial effluent, which is one of the most life-threatening factors. Herein, for the first time, two types of NiO (green and black) photocatalysts were prepared by facile chemical precipitation and thermal decomposition methods separately. The synthesized NiO materials were demonstrated with various instrumental techniques for finding their characteristics. The X-ray diffraction studies (XRD) and X-ray photoelectron spectroscopy (XPS) revealed the presence of Ni2O3 in black NiO material. The transmission electron microscopic (TEM) images engrained the nanospherical shaped green NiO and nanoflower shaped black NiO/Ni2O3 materials. Further, the band gap of black NiO nanoflower was 2.9 eV compared to green NiO having 3.8 eV obtained from UV-vis spectroscopy. Meanwhile, both NiO catalysts were employed for visible light degradation, which yields a 60.3% efficiency of black NiO comparable to a 4.3% efficiency of green NiO within 180 min of exposure. The higher degrading efficiency of black NiO was due to the presence of Ni2O3 and the development of pores, which was evident from the Barrett-Joyner-Halenda (BJH) method. Type IV hysteresis was observed in black NiO nanoflowers with high surface area and pore size measurements. This black NiO/Ni2O3 synthesized from the thermal decomposition method has promoted better photocatalytic degradation of 4-chlorophenol upon exposure to visible light and is applicable for other industrial pollutants.

The Role of SCL Isoforms in Embryonic Hematopoiesis.

Three waves of hematopoiesis occur in the mouse embryo. The primitive hematopoiesis appears as blood islands in the extra embryonic yolk sac at E7.5. The extra embryonic pro-definitive hematopoiesis launches in late E8 and the embryonic definitive one turns on at E10.5 indicated by the emergence of hemogenic endothelial cells on the inner wall of the extra embryonic arteries and the embryonic aorta. To study the roles of SCL protein isoforms in murine hematopoiesis, the SCL-large (SCL-L) isoform was selectively destroyed with the remaining SCL-small (SCL-S) isoform intact. It was demonstrated that SCL-S was specifically expressed in the hemogenic endothelial cells (HECs) and SCL-L was only detected in the dispersed cells after budding from HECs. The SCLΔ/Δ homozygous mutant embryos only survived to E10.5 with normal extra embryonic vessels and red blood cells. In wild-type mouse embryos, a layer of neatly aligned CD34+ and CD43+ cells appeared on the endothelial wall of the aorta of the E10.5 fetus. However, the cells at the same site expressed CD31 rather than CD34 and/or CD43 in the E10.5 SCLΔ/Δ embryo, indicating that only the endothelial lineage was developed. These results reveal that the SCL-S is sufficient to sustain the primitive hematopoiesis and SCL-L is necessary to launch the definitive hematopoiesis.

Particulate PCDD/F size distribution and potential deposition in respiratory system from a hazardous waste thermal treatment process.

The particulate polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) of various sizes produced from the waste incinerators might have different toxicities, deposition characteristics, and potential health effects in the respiratory system, and their total toxicity equivalent (TEQ) concentration has been strictly regulated in recent years. There is a knowledge gap on the effects of air pollution control devices on particle size distributions (PSDs) of PCDD/Fs and their TEQ deposition. A hazardous waste thermal treatment plant equipped with an advanced scrubber, a cyclone demister, and activated carbon adsorption coupled with a baghouse filtration was investigated in this study. An 8-stage impactor was used to collect the particle distribution of PM10 and bounded PCDD/Fs from the gas stream at four sampling points located before and after each control unit. A "TEQDE" index is defined for the toxicity deposition of PM10-PCDD/F in the respiratory system. The advanced scrubbers significantly reduced the PM10-PCDD/F levels, especially for those with sizes ≥0.6 and ≤ 0.4 µm. Additionally, the cyclone also showed a better performance than the general dry gas treatment but had an efficiency drop with 1.5-4 µm particles. The PM10-PCDD/F loads in the final adsorption-filtration unit were eased and effectively removed the PM10-PCDD/Fs to sizes ≤0.5 or≥1.5 µm. The total TEQDE was 0.00052 ng WHO-TEQ Nm-3 and had a peak level of 0.000157 ng WHO-TEQ Nm-3 at 1.2 µm. PSDs were more sensitive to the PSDs of PM mass at high PM levels but strongly correlated with the PSDs of "PM10-PCDD/Fs/PM10" at low PM10 loads. Consequently, the advanced control system could effectively remove the PM10-PCDD/Fs and might extend the adsorption-filtration lifetime. However, the PM10-PCDD/Fs ≤ 0.4 µm had a higher TEQ deposition rate and should be further considered in emissions and ambient air quality evaluations.

Oxidative torrefaction of microalga Nannochloropsis Oceanica activated by potassium carbonate for solid biofuel production.

Oxidative torrefaction is a promising way for biomass upgrading and solid biofuel production. Alkali metals are considered to be efficient activators for enhancing biofuel upgrading during the thermal reaction process. Herein, the microalga Nannochloropsis Oceanica is selected as the feedstock for assessing potassium carbonate activated effect on solid biofuel production through oxidative torrefaction. The potential of potassium carbonate on microalgal biofuel properties upgrading is deeply explored. SEM observation and BET analysis show that torrefied microalgae can be transformed from a spherical structure with wrinkles to smaller particles with larger surface areas and higher total pore volumes, implying that potassium carbonate is a promising porogen. Moreover, potassium carbonate can significantly change the DTG curve at the temperatures of 250 °C and 300 °C from one peak to two peaks, inferring that the activated effect of potassium carbonate occurs on the torrefied microalgae. 13C NMR analysis reveals that the microalgal components significantly change as the torrefaction severity increases, with the decomposition of carbohydrate and protein components. When the potassium carbonate ratio increases from 0:1 to 1:1, the graphitization degree increase from 3.065 to 1.262, along with the increase in the HHV of solid biofuel from 25.024 MJ kg-1 to 31.890 MJ kg-1. In total, this study has comprehensively revealed the activated effect of potassium carbonate on improving the properties of microalgal solid biofuel.

Dual pretreatment of mixing H2O2 followed by torrefaction to upgrade spent coffee grounds for fuel production and upgrade level identification of H2O2 pretreatment.

Biochar is a carbon-neutral solid fuel and has emerged as a potential candidate to replace coal. Meanwhile, spent coffee grounds (SCGs) are an abundant and promising biomass waste that could be used for biochar production. This study develops a biochar valorization strategy by mixing SCGs with hydrogen peroxide (H2O2) at a weight ratio of 1:0.75 to upgrade SCG biochar. In this dual pretreatment method, the H2O2 oxidative ability at a pretreatment temperature of 105 °C contributes to an increase in the higher heating value (HHV) and carbon content of the SCG biochars. The HHV and carbon content of biochar increase by about 6.5% and 7.8%, respectively, when compared to the unpretreated one under the same conditions. Maximized biochar's HHV derived via the Taguchi method is 30.33 MJkg-1, a 46.9% increase compared to the raw SCG, and a 6.5% increase compared to the unpretreated SCG biochar. The H2O2 concentration is 18% for the maximized HHV. A quantitative identification index of intensity of difference (IOD) is adopted to evaluate the contributive level of H2O2 pretreatment in terms of the HHV and carbon content. IOD increases with increasing H2O2 pretreatment temperature. Before torrefaction, SCGs' IOD pretreated at 50 °C is 1.94%, while that pretreated at 105 °C is 8.06%. This is because, before torrefaction, H2O2 pretreatment sufficiently weakens SCGs' molecular structure, resulting in a higher IOD value. The IOD value of torrefied SCGs (TSCG) pretreated at 105 °C is 10.71%, accounting for a 4.59% increase compared to that pretreated at 50 °C. This implies that TSCG pretreated by H2O2 at 105 °C has better thermal stability. For every 1% increase in IOD of TSCG, the carbon content of the biochar increases 0.726%, and the HHV increases 0.529%. Overall, it is demonstrated that H2O2 is a green and promising pretreatment additive for upgrading SCG biochar's calorific value, and torrefied SCGs can be used as a potential solid fuel to approach carbon neutrality.

Single-Molecule Light-Sheet Microscopy with Local Nanopipette Delivery.

The detection of single molecules in biological systems has rapidly increased in resolution over the past decade. However, the delivery of single molecules remains to be a challenge. Currently, there is no effective method that can both introduce a precise amount of molecules onto or into a single cell at a defined position and then image the cellular response. Here, we have combined light-sheet microscopy with local delivery, using a nanopipette, to accurately deliver individual proteins to a defined position. We call this method local-delivery selective-plane illumination microscopy (ldSPIM). ldSPIM uses a nanopipette and ionic feedback current at the nanopipette tip to control the position from which the molecules are delivered. The number of proteins delivered can be controlled by varying the voltage applied. For single-molecule detection, we implemented single-objective SPIM using a reflective atomic force microscopy cantilever to create a 2 µm thin sheet. Using this setup, we demonstrate that ldSPIM can deliver single fluorescently labeled proteins onto the plasma membrane of HK293 cells or into the cytoplasm. Next, we deposited the aggregates of amyloid-ß, which causes proteotoxicity relevant to Alzheimer's disease, onto a single macrophage stably expressing a MyDD88-eGFP fusion construct. Whole-cell imaging in the three-dimensional (3D) mode enables the live detection of MyDD88 accumulation and the formation of myddosome signaling complexes, as a result of the aggregate-induced triggering of toll-like receptor 4. Overall, we demonstrate a novel multifunctional imaging system capable of precise delivery of single proteins to a specific location on the cell surface or inside the cytoplasm and high-speed 3D detection at single-molecule resolution within live cells.

Analysis of microparticle deposition in the human lung by taguchi method and response surface methodology.

The deposition phenomenon of microparticle and SAR-CoV-2 laced bioaerosol in human airways is studied by Taguchi methods and response surface methodology (RSM). The data used herein is obtained from simulations of airflow dynamics and deposition fractions of drug particle aerosols in the downstream airways of asthma patients using computational fluid dynamics (CFD) and discrete particle motion (DPM). Three main parameters, including airflow rate, drug dose, and particle size, affecting aerosol deposition in the lungs of asthma patients are examined. The highest deposition fraction (DF) is obtained at the flow rate of 45 L min-1, the drug dose of 200 µg·puff-1, and the particle diameter of 5 µm. The optimized combination of levels for the three parameters for maximum drug deposition is performed via the Taguchi method. The importance of the influencing factors rank as particle size > drug dose > flow rate. RSM reveals that the combination of 30 L min-1, 5 µm, 200 µg·puff- has the highest deposition fraction. In part, this research also studied the deposition of bioaerosols contaminated with the SAR-CoV-2 virus, and their lowest DF is 1.15%. The low DF of bioaerosols reduces the probability of the SAR-CoV-2 virus transmission.