Stability of Lines with Zero Receding Contact Angle Produced by Inkjet Printing at Small Drop Volume.

We present an experimental study of the maximum and minimum bounding drop spacing for a parallel-sided liquid line produced by inkjet printing with drop volumes of 1.5 and 8.5 pL, on substrates with advancing contact angles of 46 and 54°, and zero receding contact angle. The results are used to validate models of the limiting bounds for the formation of stable parallel-sided lines as a function of drop spacing and transverse printing speed. The model for the maximum drop spacing bound (minimum line width) shows a good agreement with our results, but, when used to predict the stable line width, there is an influence of printing speed not captured by the model. This is probably because of a coupling between printed drop volume and ejection velocity outside the scope of the model. The minimum drop spacing bound (maximum stable line width) is limited by a bulging instability, and our results agree with the existing model, except for printing with the largest drop volumes at low temperature. It is shown that under these conditions, there is a different mechanism for bulging that occurs after printing over a period of minutes, if the liquid bead is present on the surface for a significant period of time before drying. Our results suggest that this mechanism is possibly triggered by imperfections on the substrate.

The systemic influence of chronic smoking on skin structure and mechanical function.

One of the major functions of human skin is to provide protection from the environment. Although we cannot entirely avoid, for example, sun exposure, it is likely that exposure to other environmental factors could affect cutaneous function. A number of studies have identified smoking as one such factor that leads to both facial wrinkle formation and a decline in skin function. In addition to the direct physical effects of tobacco smoke on skin, its inhalation has additional profound systemic effects for the smoker. The adverse effects on the respiratory and cardiovascular systems from smoking are well known. Central to the pathological changes associated with smoking is the elastic fibre, a key component of the extracellular matrices of lungs. In this study we examined the systemic effect of chronic smoking (>40 cigarettes/day; >5 years) on the histology of the cutaneous elastic fibre system, the nanostructure and mechanics of one of its key components, the fibrillin-rich microfibril, and the micromechanical stiffness of the dermis and epidermis. We show that photoprotected skin of chronic smokers exhibits significant remodelling of the elastic fibre network (both elastin and fibrillin-rich microfibrils) as compared to the skin of age- and sex-matched non-smokers. This remodelling is not associated with increased gelatinase activity (as identified by in situ zymography). Histological remodelling is accompanied by significant ultrastructural changes to extracted fibrillin-rich microfibrils. Finally, using scanning acoustic microscopy, we demonstrated that chronic smoking significantly increases the stiffness of both the dermis and the epidermis. Taken together, these data suggest an unappreciated systemic effect of chronic inhalation of tobacco smoke on the cutaneous elastic fibre network. Such changes may in part underlie the skin wrinkling and loss of skin elasticity associated with smoking. © 2020 The Authors. The Journal of Pathology published by John Wiley & Sons Ltd on behalf of Pathological Society of Great Britain and Ireland.

Patterned, morphing composites via maskless photo-click lithography.

Morphing materials, also known as smart materials are attracting increasing attention as sensors, actuators and in soft robotic applications. In this work bilayered morphing composites were created by exploiting the thiol-ene photoclick reaction via maskless digital light processing (DLP). This technique allows for gradients and patterns of near infrared (nIR)-triggered materials to be efficiently crosslinked to substrates, with suitable interfacial adhesion to realise complex morphing. Photo-thermally responsive composites are produced by DLP patterning of reduced graphene oxide-filled chitosan-methacrylamide (rGO-chitosan-MA) on thiolated polydimethylsiloxane substrates via thiol-ene photoclick reaction. Morphing composites with parallel striped patterns and box-like hinges were printed via DLP to realise self-rolling and self-folding behaviours. Bilayered structures, with gradient rGO-chitosan-MA thicknesses (2-8 µm), were produced by controlling the light intensity from the DLP device. These gradient bilayered structures enable photothermal-triggered gradient bending and morphing exemplified here by a "walking worm" and a kirigami-inspired "opening flower". Thermo-mechanical calculations were performed to estimate bending angles, and finite element analysis applied to simulate self-folding and bending. The difference between simulation and measurements is in the range 0.4-7.6%, giving confidence to the assumptions and simplifications applied in design.

The formation mechanism of hexagonal Mo2C defects in CVD graphene grown on liquid copper.

Thin Mo2C hexagonal defects precipitate in CVD graphene when Mo crucibles are engaged to hold the liquid copper substrate, while these defects disappear when W crucibles are present. These defects have been identified as the thin precipitates of Mo2C. The growth mechanism of the Mo2C defects is demonstrated through thermodynamic calculations. This can be beneficial in graphene defect engineering through the vapour phase transport of the volatile MoO3 phase.

Structural, Mechanical, Imaging and in Vitro Evaluation of the Combined Effect of Gd3+ and Dy3+ in the ZrO2-SiO2 Binary System.

Mechanical strength and biocompatibility are considered the main prerequisites for materials in total hip replacement or joint prosthesis. Noninvasive surgical procedures are necessary to monitor the performance of a medical device in vivo after implantation. To this aim, simultaneous Gd3+ and Dy3+ additions to the ZrO2-SiO2 binary system were investigated. The results demonstrate the effective role of Gd3+ and Dy3+ to maintain the structural and mechanical stability of cubic zirconia ( c-ZrO2) up to 1400 °C, through their occupancy of ZrO2 lattice sites. A gradual tetragonal to cubic zirconia ( t-ZrO2 → c-ZrO2) phase transition is also observed that is dependent on the Gd3+ and Dy3+ content in the ZrO2-SiO2. The crystallization of either ZrSiO4 or SiO2 at elevated temperatures is delayed by the enhanced thermal energy consumed by the excess inclusion of Gd3+ and Dy3+ at c-ZrO2 lattice. The addition of Gd3+ and Dy3+ leads to an increase in the density, elastic modulus, hardness, and toughness above that of unmodified ZrO2-SiO2. The multimodal imaging contrast enhancement of the Gd3+ and Dy3+ combinations were revealed through magnetic resonance imaging and computed tomography contrast imaging tests. Biocompatibility of the Gd3+ and Dy3+ dual-doped ZrO2-SiO2 systems was verified through in vitro biological studies.

Two-Step Electrochemical Intercalation and Oxidation of Graphite for the Mass Production of Graphene Oxide.

Conventional chemical oxidation routes for the production of graphene oxide (GO), such as the Hummers' method, suffer from environmental and safety issues due to their use of hazardous and explosive chemicals. These issues are addressed by electrochemical oxidation methods, but such approaches typically have a low yield due to inhomogeneous oxidation. Herein we report a two-step electrochemical intercalation and oxidation approach to produce GO on the large laboratory scale (tens of grams) comprising (1) forming a stage 1 graphite intercalation compound (GIC) in concentrated sulfuric acid and (2) oxidizing and exfoliating the stage 1 GIC in an aqueous solution of 0.1 M ammonium sulfate. This two-step approach leads to GO with a high yield (>70 wt %), good quality (>90%, monolayer), and reasonable oxygen content (17.7 at. %). Moreover, the as-produced GO can be subsequently deeply reduced (3.2 at. % oxygen; C/O ratio 30.2) to yield highly conductive (54 600 S m-1) reduced GO. Electrochemical capacitors based on the reduced GO showed an ultrahigh rate capability of up to 10 V s-1 due to this high conductivity.

Tetragonal to Cubic Transformation of SiO2-Stabilized ZrO2 Polymorph through Dysprosium Substitutions.

Partially stabilized tetragonal zirconia (t-ZrO2) is of particular interest for hard tissue replacements. Aging-related failures of the ceramic associated with the gradual transformation from t-ZrO2 to m-ZrO2 (monoclinic zirconia) can lead to its premature removal from the implant site. In addition, monitoring the satisfactory performance of the implant throughout its lifespan without invasive techniques is a challenging task. The magnetic resonance imaging (MRI) contrast ability of dysprosium (Dy3+) is well-established. To this aim, varied levels of Dy3+ additions in the ZrO2-SiO2 binary oxide system were explored. The results indicate the effective role of Dy3+ in the formation of thermally and mechanically stable c-ZrO2 (cubic zirconia) phase at higher temperatures. The presence of SiO2 influenced the t-ZrO2 stabilization, whereas Dy3+ tends to occupy the ZrO2 lattice sites to induce c-ZrO2 transition. Magnetic and MRI tests displayed the commendable contrast ability of Dy3+ stabilized ZrO2-SiO2 binary systems. Nanoindentation results demonstrate a remarkable enhancement of the mechanical properties.

An ex vivo porcine skin model to evaluate pressure-reducing devices of different mechanical properties used for pressure ulcer prevention.

Pressure ulcers are complex wounds caused by pressure- and shear-induced trauma to skin and underlying tissues. Pressure-reducing devices, such as dressings, have been shown to successfully reduce pressure ulcer incidence, when used in adjunct to pressure ulcer preventative care. While pressure-reducing devices are available in a range of materials, with differing mechanical properties, understanding of how a material's mechanical properties will influence clinical efficacy remains limited. The aim of this study was to establish a standardized ex vivo model to allow comparison of the cell protection potential of two gel-like pressure-reducing devices with differing mechanical properties (elastic moduli of 77 vs. 35 kPa). The devices also displayed differing energy dissipation under compressive loading, and resisted strain differently under constant load in compressive creep tests. To evaluate biological efficacy we employed a new ex vivo porcine skin model, with a confirmed elastic moduli closely matching that of human skin (113 vs. 119 kPa, respectively). Static loads up to 20 kPa were applied to porcine skin ex vivo with subsequent evaluation of pressure-induced cell death and cytokine release. Pressure application alone increased the percentage of epidermal apoptotic cells from less than 2% to over 40%, and increased cellular secretion of the pro-inflammatory cytokine TNF-alpha. Co-application of a pressure-reducing device significantly reduced both cellular apoptosis and cytokine production, protecting against cellular damage. These data reveal new insight into the relationship between mechanical properties of pressure-reducing devices and their biological effects. After appropriate validation of these results in clinical pressure ulcer prevention with all tissue layers present between the bony prominence and external surface, this ex vivo porcine skin model could be widely employed to optimize design and evaluation of devices aimed at reducing pressure-induced skin damage.

Vertical Sculpted Pillar Reduction Mammaplasty in 317 Patients: Technique, Complications, and BREAST-Q Outcomes.

BACKGROUND: The senior author (JCG) has described the vertical sculpted pillar breast reduction. OBJECTIVES: This manuscript aimed to compare this technique's safety profile to other established techniques via complication rate reporting. Few studies have utilized the BREAST-Q for long-term outcomes reporting in bilateral reduction mammaplasty patients. BREAST-Q outcome comparisons, between cosmetic and insurance-based breast reduction cohorts, have not been previously reported. METHODS: A retrospective chart review was performed on patients who underwent reduction mammaplasty using the vertical sculpted pillar technique. The BREAST-Q postoperative reduction mammaplasty module was administered. Complication rates and outcomes data were compared among patient cohorts distinguished by pedicle, scar pattern, and payor population. Statistically significant differences were set at P < .05. RESULTS: Compared to the superior pedicle, use of the superomedial pedicle statistically increased rates of postoperative fat necrosis in this series. Complication rates did not differ among scar patterns, but use of a J, L-shaped, or short-T scar decreased the need for secondary/revisional surgery. Cosmetic and insurance-based outcomes did not differ in any domain of the postoperative reduction mammaplasty BREAST-Q module. CONCLUSIONS: Complications data for the vertical sculpted pillar reduction mammaplasty were comparable to published results for other techniques. Complication rates are unaffected by scar pattern. Superomedial pedicle selection and larger insurance-based reductions may predispose to statistically significant increases in fat necrosis compared to use of the superior pedicle. Payor source neither affects the majority of complication rates, nor BREAST-Q satisfaction and quality of life domains. This information can be used to improve management of expectations during the preoperative consultation process. LEVEL OF EVIDENCE: 4 Therapeutic.

Tin(II) Sulfide (SnS) Nanosheets by Liquid-Phase Exfoliation of Herzenbergite: IV-VI Main Group Two-Dimensional Atomic Crystals.

The liquid-phase exfoliation of tin(II) sulfide to produce SnS nanosheets in N-methyl-2-pyrrolidone is reported. The material is characterized by Raman spectroscopy, atomic force microscopy, lattice-resolution scanning transmission electron microscope imaging, and energy dispersive X-ray spectrum imaging. Quantum chemical calculations on the optoelectronic characteristics of bulk and 10-layer down to monolayer SnS have been performed using a quantum chemical density functional tight-binding approach. The optical properties of the SnS and centrifugally fractionated SnS nanosheet dispersions were compared to that predicted by theory. Through centrifugation, bilayer SnS nanosheets can be produced size-selectively. The scalable solution processing of semiconductor SnS nanosheets is the key to their commercial exploitation and is potentially an important step toward the realization of a future electronics industry based on two-dimensional materials.

Combining AFM and acoustic probes to reveal changes in the elastic stiffness tensor of living cells.

Knowledge of how the elastic stiffness of a cell affects its communication with its environment is of fundamental importance for the understanding of tissue integrity in health and disease. For stiffness measurements, it has been customary to quote a single parameter quantity, e.g., Young's modulus, rather than the minimum of two terms of the stiffness tensor required by elasticity theory. In this study, we use two independent methods (acoustic microscopy and atomic force microscopy nanoindentation) to characterize the elastic properties of a cell and thus determine two independent elastic constants. This allows us to explore in detail how the mechanical properties of cells change in response to signaling pathways that are known to regulate the cell's cytoskeleton. In particular, we demonstrate that altering the tensioning of actin filaments in NIH3T3 cells has a strong influence on the cell's shear modulus but leaves its bulk modulus unchanged. In contrast, altering the polymerization state of actin filaments influences bulk and shear modulus in a similar manner. In addition, we can use the data to directly determine the Poisson ratio of a cell and show that in all cases studied, it is less than, but very close to, 0.5 in value.

Adipose-derived stem cell to epithelial stem cell transdifferentiation: a mechanism to potentially improve understanding of fat grafting's impact on skin rejuvenation.

BACKGROUND: Recent evidence suggests that lipofilling improves overlying skin composition and appearance. Adipose-derived stem cells (ADSC) have been implicated. OBJECTIVE: The authors identify ADSC transdifferentiation into epithelial stem cells through coexpression of GFP+ (green fluorescent protein positive) ADSC with the epithelial stem cell marker p63 in an in vivo fat grafting model. METHODS: Six male, GFP+ mice served as adipose tissue donors. Twelve nude mice served as recipients. Recipients were subdivided into 2 arms (6 mice/each arm) and received either whole-fat specimen (group 1) or isolated and purified ADSC + peptide hydrogel carrier (group 2) engrafted into a 1-cm(2) left parascapular subdermal plane. The right parascapular subdermal plane served as control. Skin flaps were harvested at 8 weeks and subjected to (1) confocal fluorescent microscopy and (2) reverse transcriptase polymerase chain reaction (RT-PCR) for p63 mRNA expression levels. RESULTS: Gross examination of skin flaps demonstrated subjectively increased dermal vessel presence surrounding whole-fat and ADSC specimens. The GFP+ cells were seen within overlying dermal architecture after engraftment and were found to coexpress p63. Significantly increased levels of p63 expression were found in the ADSC + hydrogel skin flaps. CONCLUSIONS: We offer suggestive evidence that GFP+ ADSC are found within the dermis 8 weeks after engraftment and coexpress the epithelial stem cell marker p63, indicating that ADSC may transdifferentiate into epithelial stem cells after fat grafting. These findings complement current understanding of how fat grafts may rejuvenate overlying skin.

Collagen IV assembly is influenced by fluid flow in kidney cell-derived matrices.

Kidney podocytes and endothelial cells assemble a complex and dynamic basement membrane that is essential for kidney filtration. Whilst many components of this specialised matrix are known, the influence of fluid flow on its assembly and organisation remains poorly understood. Using the coculture of podocytes and glomerular endothelial cells in a low-shear stress, high-flow bioreactor, we investigated the effect of laminar fluid flow on the composition and assembly of cell-derived matrix. With immunofluorescence and matrix image analysis we found flow-mediated remodelling of collagen IV. Using proteomic analysis of the cell-derived matrix we identified changes in both abundance and composition of matrix proteins under flow, including the collagen-modifying enzyme, prolyl 4-hydroxylase (P4HA1). To track collagen IV assembly, we used CRISPR-Cas9 to knock in the luminescent marker HiBiT to the endogenous COL4A2 gene in podocytes. With this system, we found that collagen IV was secreted and accumulated consistently under both static and flow conditions. However knockdown of P4HA1 in podocytes led to a reduction in the secretion of collagen IV and this was more pronounced under flow. Together, this work demonstrates the effect of fluid flow on the composition, modification, and organisation of kidney cell-derived matrix and provides an in vitro system for investigating flow-induced matrix alteration in the context of kidney development and disease.

Graphene-Based Transparent Flexible Strain Gauges with Tunable Sensitivity and Strain Range.

Monolayers of graphene oxide, assembled into densely packed sheets at an immiscible hexane/water interface, form transparent conducting films on polydimethylsiloxane membranes after reduction in hydroiodic acid (HI) vapor to reduced graphene oxide (rGO). Prestraining and relaxing the membranes introduces cracks in the rGO film. Subsequent straining opens these cracks and induces piezoresistivity, enabling their application as transparent strain gauges. The sensitivity and strain range of these gauges is controlled by the cracked film structure that is determined by the reducing conditions used in manufacture. Reduction for 30 s in HI vapor leads to an array of parallel cracks that do not individually span the membrane. These cracks do not extend on subsequent straining, leading to a gauge with a usable strain range >0.2 and gauge factor (GF) at low strains ranging from 20 to 100, depending on the prestrain applied. The GF reduces with increasing applied strain and asymptotes to about 3, for all prestrains. Reduction for 60 s leads to cracks spanning the entire membrane and an increased film resistance but a highly sensitive strain gauge, with GF ranging from 800 to 16,000. However, the usable strain range reduces to <0.01. A simple equivalent resistor model is proposed to describe the behavior of both gauge types. The gauges show a repeatable and stable response with loading frequencies >1 kHz and have been used to detect human body strains in a simple e-skin demonstration.

Formation of coffee stains on porous surfaces.

During the drying of drops of nanoparticle suspensions, segregation can occur by internal fluid flows toward the contact line, if the contact line is pinned. This leads to a characteristic ring deposit or coffee stain. On solid substrates coffee staining can be eliminated through the use of solvent mixtures that promote Marangoni flows to oppose these drying-induced flows. Here it is shown that a suspension, optimized to eliminate the formation of coffee stains on a range of solid surfaces, shows coffee staining on a number of porous surfaces. This behavior is shown to be consistent with a mechanism of fluid removal through capillary flow (draining) of the solvent into the porous substrate, combined with filtration of the particles by the small pore size, in addition to the flow from solvent evaporation. The extent of capillary driven coffee staining is a function of substrate pore size: if the pore size is small, capillary flow is slow, reducing the observed coffee staining. However, if the pore size is too large, the nanoparticles are absorbed into the material along with the draining solute and no deposition of particles is observed.

Stability Bounds for Micron Scale Ag Conductor Lines Produced by Electrohydrodynamic Inkjet Printing.

Continuous conducting lines of width 5-20 µm have been printed with a Ag nanoparticle ink using drop-on-demand (DOD) electrohydrodynamic (EHD) inkjet printing on Si and PDMS substrates, with advancing contact angles of 11° and 35°, respectively, and a zero receding contact angle. It is only possible to achieve stable parallel sided lines within a limited range of drop spacings, and this limiting range for stable line printing decreases as the contact angle of the ink on the substrate increases. The upper bound drop spacing for stable line formation is determined by a minimum drop overlap required to prevent contact line retraction, and the lower bound is governed by competing flows for drop spreading onto an unwetted substrate and a return flow driven by a Laplace pressure difference between the newly deposited drops and the fluid some distance from the growing tip. The upper and lower bounds are shown to be consistent with those predicted using existing models for the stability of inkjet printed lines produced using piezoelectric droplet generators. A comparison with literature data for EHD printed lines finds that these limiting bounds apply with printed line widths as small as 200 nm using subfemtoliter drop volumes. When a fine grid pattern is printed, local differences in Laplace pressure lead to the line width retracting to the minimum stable width and excess ink being transported to the nodes of the grid. After printing and sintering, the printed tracks have a conductivity of about 15%-20% of bulk Ag on the Si substrate, which correlates with a porosity of about 60%.

Characterizing the elastic properties of tissues.

The quality of life of ageing populations is increasingly determined by age-related changes to the mechanical properties of numerous biological tissues. Degradation and mechanical failure of these tissues has a profound effect on human morbidity and mortality. Soft tissues have complex and intricate structures and, similar to engineering materials, their mechanical properties are controlled by their microstructure. Thus age-relate changes in mechanical behavior are determined by changes in the properties and relative quantities of microstructural tissue components. This review focuses on the cardiovascular system; it discusses the techniques used both in vivo and ex vivo to determine the age-related changes in the mechanical properties of arteries.

Fabrication of microvascular constructs using high resolution electrohydrodynamic inkjet printing.

Fabrication of the intricate anatomy of vasculature within engineered tissue remains one of the key challenges facing the field of tissue engineering. We report the use of electrohydrodynamic (EHD) inkjet printing to create hydrogel-based microvascular tissues with hierarchical and branching channels, whose minimum feature size of 30µm approaches the physical scale of native capillary blood vessels. The principle relies on the use of complementary thermoreversible gelling properties of Pluronic F127 (PF-127) and gelatin methacryloyl, which served as sacrificial templates and permanent matrices respectively. Human dermal fibroblasts and human umbilical vein endothelial cells were successfully co-cultured within the engineered microvascular tissue constructs for up to 21 days, and attained high cell viability. Tissue specific morphology was maintained on perfusion. The ability to create cellularised, vascularised proto-tissues with high spatial resolution using EHD inkjet printing, provides a new strategy for developing advanced vascular models with the potential to impact upon an extensive range of biomedical applications.

Formation and stability of lines produced by inkjet printing.

To produce stable lines with parallel sides through inkjet printing, individual drops are deposited on a surface so that they coalesce; this initial liquid line (or bead) must remain stable until it forms a solid. The stable line width is shown to be bounded by two limits, with the lower bound (minimum line width) determined by the maximum drop spacing for stable coalescence and the upper bound determined by the minimum drop spacing below which a bulging instability occurs. The maximum stable track width is also a function of the velocity at which an inkjet printhead traverses the substrate. These bounds are presented in dimensionless form and are shown to agree well with experiment. To enable easier determination of the stability of an arbitrary ink/substrate combination, both the upper and lower bounds are presented in graphical forms to define a region of bead stability in an appropriate parameter space.