RESUMEN
By modifying the interconnection design between standard single-mode fiber (SSMF) and nested antiresonant nodeless type hollow-core fiber (NANF), we create an air gap between SSMF and NANF. This air gap enables the insertion of optical elements, thus providing additional functions. We show low-loss coupling using various graded-index multimode fibers acting as mode-field adapters resulting in different air-gap distances. Finally, we test the gap functionality by inserting a thin glass sheet in the air gap, which forms a Fabry-Perot interferometer and works as a filter with an overall insertion loss of only 0.31 dB.
RESUMEN
We report simultaneous low coupling loss (below 0.2 dB at 1550 nm) and low back-reflection (below -60 dB in the 1200-1600 nm range) between a hollow core fiber and standard single mode optical fiber obtained through the combination of an angled interface and an anti-reflective coating. We perform experimental optimization of the interface angle to achieve the best combination of performance in terms of the coupling loss and back-reflection suppression. Furthermore, we examine parasitic cross-coupling to the higher-order modes and show that it does not degrade compared to the case of a flat interface, keeping it below -30 dB and below -20 dB for LP11 and LP02 modes, respectively.
RESUMEN
A monolithic fiber laser operating in the short wavelength infrared that is suitable for CO2 gas sensing applications is proposed and presented. The current study reports a laser design based on the direct inscription of a monolithic Fabry-Perot (FP) cavity in a thulium-doped optical fiber using the femtosecond laser (FsL) plane-by-plane inscription method to produce the cavity mirrors. The FP cavity was inscribed directly into the active fiber using two wavelength-identical fiber Bragg gratings (FBGs), one with high and one with low reflectivity. Initially the effective length of the fiber was defined using a single high reflectivity FBG and subsequently a very weak FBG was inscribed at the other end of the fiber in order to demonstrate a fully monolithic fiber laser. All fiber lasers were designed for continuous wave operation at 1950 nm and characterized with respect to the power output, slope efficiency, stability, and effective resonator length. The performance of the presented monolithic laser cavities was evaluated using the same active fiber as a reference fiber spliced to FBGs inscribed in passive fiber; an improvement exceeding 12% slope efficiency is reported for the presented monolithic laser.
RESUMEN
Two experimental configurations of a hybrid K-band (25 GHz) microwave photonic link (MPL) are investigated for seamless broadband wireless access networks. Experimental configurations consist of optical fiber, free-space optics (FSO) and radio frequency (RF) wireless channels. We analyze in detail the effects of channel impairments, namely fiber chromatic dispersion, atmospheric turbulence and multipath-induced fading on the transmission performance. In the first configuration, transmission of the 64-quadrature amplitude modulation (QAM) signal with 5, 20 and 50 MHz bandwidths over 5 km standard single-mode fiber (SSMF), 2 m turbulent FSO and 3 m RF wireless channels is investigated. We show that, for QAM with a high bandwidth, the link performance is being affected more by atmospheric turbulence. In the second configuration, the 20 MHz 4/16/64-QAM signals over a 50 km SSMF and 40 m FSO/RF wireless links are successfully transmitted with the measured error vector magnitude (EVM) values of 12, 9 and 7.9%, respectively. It is shown that, for all transmitted microwave vector signals, the bit error rate is lower than the hard-decision forward-error-correction limit of 3.8×10-3. Moreover, an extended FSO link span of 500 m for 25 GHz hybrid MPL with 16-QAM at 10 Gb/s under the weak and strong turbulence regimes is evaluated via simulation analysis to mimic a practical outdoor system.
RESUMEN
We demonstrate halving the record-low loss of interconnection between a nested antiresonant nodeless type hollow-core fiber (NANF) and standard single-mode fiber (SMF). The achieved interconnection loss of 0.15 dB is only 0.07 dB above the theoretically-expected minimum loss. We also optimized the interconnection in terms of unwanted cross-coupling into the higher-order modes of the NANF. We achieved cross-coupling as low as -35 dB into the LP[Formula: see text] mode (the lowest-loss higher-order mode and thus the most important to eliminate). With the help of simulations, we show that the measured LP[Formula: see text] mode coupling is most likely limited by the slightly imperfect symmetry of the manufactured NANF. The coupling cross-talk into the highly-lossy LP[Formula: see text] mode ([Formula: see text] dB/km in our fiber) was measured to be below -22 dB. Furthermore, we show experimentally that the anti-reflective coating applied to the interconnect interface reduces the insertion loss by 0.15 dB while simultaneously reducing the back-reflection below -40 dB over a 60 nm bandwidth. Finally, we also demonstrated an alternative mode-field adapter to adapt the mode-field size between SMF and NANF, based on thermally-expanded core fibers. This approach enabled us to achieve an interconnection loss of 0.21 dB and cross-coupling of -35 dB into the LP[Formula: see text] mode.