Molecularly imprinted polymer nanoparticles-based electrochemical sensor for determination of diazinon pesticide in well water and apple fruit samples.

In this research, an electrochemical sensor based on molecularly imprinted polymer (MIP) nanoparticles for selective and sensitive determination of diazinon (DZN) pesticides was developed. The nanoparticles of diazinon imprinted polymer were synthesized by suspension polymerization and then used for modification of carbon paste electrode (CPE) composition in order to prepare the sensor. Cyclic voltammetry (CV) and square wave voltammetry (SWV) methods were applied for electrochemical measurements. The obtained results showed that the carbon paste electrode modified by MIP nanoparticles (nano-MIP-CP) has much higher adsorption ability for diazinon than the CPE based non-imprinted polymer nanoparticles (nano-NIP-CP). Under optimized extraction and analysis conditions, the proposed sensor exhibited excellent sensitivity (95.08 µA L µmol(-1)) for diazinon with two linear ranges of 2.5 × 10(-9) to 1.0 × 10(-7) mol L(-1) (R (2) = 0.9971) and 1.0 × 10(-7) to 2.0 × 10(-6) mol L(-1) (R (2) = 0.9832) and also a detection limit of 7.9 × 10(-10) mol.L(-1). The sensor was successfully applied for determination of diaznon in well water and apple fruit samples with recovery values in the range of 92.53-100.86 %. Graphical abstract Procedure for preparation of electrochemical sensor based on MIP nanoparticles for determination of diazinon.

Sample preparation method for the analysis of some organophosphorus pesticides residues in tomato by ultrasound-assisted solvent extraction followed by dispersive liquid-liquid microextraction.

A very simple and economic method for organophosphorus pesticides (OPPs) residues analysis in tomato by means of gas chromatography-flame photometric detection (GC-FPD) has been developed. The method involves a rapid and small-scale extraction. The sample was homogenised and extraction of the OPPs with acetone was carried out assisted by sonication. No clean-up or evaporation were required after extraction. Pre-concentration of the OPPs from the acetone extract was done by using dispersive liquid-liquid microextraction (DLLME) technique. Chlorobenzene was added in micro-level volume as extraction solvent and triphenylphosphate as internal standard in DLLME procedure. The method showed good linearity over the range assayed (0.5-1000µgkg(-1)) and the detection limits for the pesticides studied varied from 0.1 to 0.5µgkg(-1). Repeatability studies resulted a relative standard deviation lower than 10% in all cases. The proposed method was used to determine pesticides levels in tomatoes grown in open field.

A 96-Monolithic inorganic hollow fiber array as a new geometry for high throughput solid-phase microextraction of doxorubicin in water and human urine samples coupled with liquid chromatography-tandem mass spectrometry.

Innovations in extraction phases, extraction modes and hyphenated instrument configurations, are the most important issues to address for progress in the solid phase microextraction (SPME) methodology. In this regard, we have embarked on the development of a novel biocompatible 96-monolithic inorganic hollow fiber (96-MIHF) array as a new configuration for high-throughput SPME on a 96-well plate system. An arrangement of highly ordered 96 titania/Hydroxyapatite (TiO2/HAP) nanocomposite hollow fibers and corresponding stainless-steel needles on a Teflon plate holder were used as the extraction module. The inorganic hollow fibers were prepared via a rapid and reproducible template approach (Polypropylene hollow fiber) in combination with a sol-gel method in the presence of polyvinyl alcohol (PVA), as a network maker. The hollow fiber-shape sorbents were obtained with excellent precision by weight (RSD% = 4.98, n = 10) and length (RSD% = 1.08, n = 10) criteria. The proposed design can overcome a number of geometrically dependent drawbacks of conventional high-throughput SPME methods, mainly the ones related to sorbent amount and surface area due to possessing inner/outer surfaces without additional internal supports. The SPME platform, for the first time, was successfully applied for the extraction and preconcentration of doxorubicin from urine and water media without requiring sample preparation and free from significant matrix effect. The extracted analyte was analyzed by liquid chromatography-ion trap tandem mass spectrometry (LC-MS/MS). Highly satisfactory analytical figures of merit were obtained under optimized conditions. The limit of detection (LOD), limit of quantification (LOQ) and linearity of determination were 0.1 ng mL-1, 0.25 ng mL-1 and 0.25 to 4000 ng mL-1, respectively. The interday, intraday and inter sorbent precisions for three concentration levels ranged from 2.01 to 8.09 % (n = 3), 1.02 to 8.65 % (n = 5) and 0.99 to 1.02% (n = 15), respectively. The mean intra-well RSD value for 96 individual wells in 96-MIHF-SPME-LC-MS/MS (n = 3) at the medium concentration level was 7.81%.

Speciation of butyl and phenyltin compounds using dispersive liquid-liquid microextraction and gas chromatography-flame photometric detection.

Dispersive liquid-liquid microextraction and gas chromatography-flame photometric detection (DLLME-GC-FPD) were performed for the speciation of butyl and phenyltin compounds in water samples after derivatization with sodium tetraethylborate (NaBEt4). Some important parameters, such as pH, amount of NaBEt4, derivatization time, kind and volume of extraction and disperser solvents, extraction time and salt effect were investigated and optimized. High enrichment factors (825-1036) and low detection limits (0.2-1 ng L(-1)) were obtained under the optimum conditions. The calibration graphs were linear in the range of 0.5-1000 ng L(-1) (as Sn) for the target analytes. The relative standard deviations (RSDs) for the extraction of 20 ng L(-1) (as Sn) of butyl and phenyltin compounds varied from 2.3 to 5.9% (n=7) and from 4.1 to 8.8% (n=7) with and without using internal standard, respectively. Seawater and river water samples were successfully analyzed using the proposed method and the relative recoveries of the studied compounds in the water samples, at spiking levels of 10.0 and 100 ng L(-1) (as Sn) were obtained to be 82.5-104.7%.

Determination of chlorophenols in water samples using simultaneous dispersive liquid-liquid microextraction and derivatization followed by gas chromatography-electron-capture detection.

Simultaneous dispersive liquid-liquid microextraction (DLLME) and derivatization combined with gas chromatography-electron-capture detection (GC-ECD) was used to determine chlorophenols (CPs) in water sample. In this derivatization/extraction method, 500 microL acetone (disperser solvent) containing 10.0 microL chlorobenzene (extraction solvent) and 50 microL acetic anhydride (derivatization reagent) was rapidly injected by syringe in 5.00 mL aqueous sample containing CPs (analytes) and K(2)CO(3) (0.5%, w/v). Within a few seconds the analytes derivatized and extracted at the same time. After centrifugation, 0.50 microL of sedimented phase containing enriched analytes was determined by GC-ECD. Some effective parameters on derivatization and extraction, such as extraction and disperser solvent type and their volume, amount of derivatization reagent, derivatization and extraction time, salt addition and amount of K(2)CO(3) were studied and optimized. Under the optimum conditions, enrichment factors and recoveries are in the range of 287-906 and 28.7-90.6%, respectively. The calibration graphs are linear in the range of 0.02-400 microg L(-1) and limit of detections (LODs) are in the range of 0.010-2.0 microg L(-1). The relative standard deviations (RSDs, for 200 microg L(-1) of MCPs, 100 microg L(-1) of DCPs, 4.00 microg L(-1) of TCPs, 2.00 microg L(-1) of TeCPs and PCP in water) with and without using internal standard are in the range of 0.6-4.7% (n=7) and 1.7-7.1% (n=7), respectively. The relative recoveries of well, tap and river water samples which have been spiked with different levels of CPs are 91.6-104.7, 80.8-117.9 and 83.3-101.3%, respectively. The obtained results show that simultaneous DLLME and derivatization combined with GC-ECD is a fast simple method for the determination of CPs in water samples.

Solid-phase extraction combined with dispersive liquid-liquid microextraction-ultra preconcentration of chlorophenols in aqueous samples.

The solid-phase extraction (SPE) joined with the dispersive liquid-liquid microextraction (DLLME) has been developed as an ultra preconcentration technique for the determination of chlorophenols in water samples. Chlorophenols (CPs) were employed as model compounds to assess the extraction procedure and were determined by gas chromatography-electron-capture detection (GC-ECD). In solid-phase extraction-dispersive liquid-liquid microextraction (SPE-DLLME), CPs were adsorbed from a large volume of aqueous samples (100 mL) into 100 mg functionalized styrene-divinylbenzene polymer (PPL) sorbent. After the elution of the desired compounds from the sorbent by using acetone, DLLME technique was performed on the obtained solution. Some important extraction parameters, such as sample solution flow rate, breakthrough volume, sample pH, type and volume of the elution solvent as well as the salt addition, were studied and optimized. The new method (SPE-DLLME) provided an ultra enrichment factor (4390-17,870) for 19 CPs. The calibration graphs were linear in the range of 0.001-20 microg L(-1) and the limits of detection (LODs) ranged from 0.0005 to 0.1 microg L(-1). The relative standard deviations (RSDs, for 10.0 microg L(-1) of MCPs, 5.00 microg L(-1) of DCPs, 0.200 microg L(-1) of TCPs, 0.100 microg L(-1) of TeCPs and PCP) with and without the internal standard varied from 1.1 to 6.4% (n=7) and 2.5-9.7% (n=7), respectively. The relative recoveries of the well, tap and river water samples, spiked with different levels of CPs, were 71-110%, 73-115% and 88-121%, respectively.

New method based on combining ultrasonic assisted miniaturized matrix solid-phase dispersion and homogeneous liquid-liquid extraction for the determination of some organochlorinated pesticides in fish.

In this study, ultrasonic assisted miniaturized matrix solid-phase dispersion (US-MMSPD) combined with homogeneous liquid-liquid extraction (HLLE) has been developed as a new method for the extraction of organochlorinated pesticides (OCPs) in fish prior to gas chromatography with electron capture detector (GC-ECD). In the proposed method, OCPs (heptachlor, aldrin, DDE, DDD, lindane and endrin) were first extracted from fish sample into acetonitrile by US-MMSPD procedure, and the extract was then used as consolute solvent in HLLE process. Optimal condition for US-MMSPD step was as follows: volume of acetonitrile, 1.5 mL; temperature of ultrasound, 40°C; time of ultrasound, 10 min. For HLLE step, optimal results were obtained at the following conditions: volume of chloroform, 35 µL; volume of aqueous phase, 1.5 mL; volume of double distilled water, 0.5 mL; time of centrifuge, 10 min. Under the optimum conditions, the enrichment factors for the studied compounds were obtained in the range of 185-240, and the overall recoveries were ranged from 39.1% to 81.5%. The limits of detection were 0.4-1.2 ng g(-1) and the relative standard deviations for 20 ng g(-1) of the OCPs, varied from 3.2% to 8% (n=4). Finally, the proposed method has been successfully applied to the analysis of the OCPs in real fish sample, and satisfactory results were obtained.

Highly improved electrooxidation of glucose at a nickel(II) oxide/multi-walled carbon nanotube modified glassy carbon electrode.

Electrochemical oxidation of glucose on a glassy carbon disc electrode modified with multi-walled carbon nanotubes and nickel(II) oxide (GC/MWCNT/NiO) was examined by cyclic voltammetry and chronoamperometry in alkaline aqueous solutions. The results were compared with those obtained on a nickel(II) oxide modified glassy carbon electrode (GC/NiO). Both electrodes conditioned by potential cycling in a limited potential range (0.1-0.6 V vs. Ag/AgCl) in 0.10 M NaOH solution. It was found that the multi-walled carbon nanotubes improve remarkably the reactivity of nickel(II) oxide for glucose oxidation. The GC/MWCNT/NiO electrode exhibited good linear behavior in the concentration range from 2.0x10(-4) mol/L to 1.2x10(-2) mol/L for the quantitative analysis of glucose with a limit of detection of 1.6x10(-4) mol/L (3sigma). The prepared electrode exhibits satisfactory stability and long life if stored at ambient conditions. Finally, it has been demonstrated that the proposed modified electrode can be successfully used for the assay of glucose in serum samples.

Development of dispersive liquid-liquid microextraction method for the analysis of organophosphorus pesticides in tea.

In this article, a new method for the determination of organophosphorus pesticides (OPPs) in tea was developed by using dispersive liquid-liquid microextraction (DLLME) and gas chromatography-flame photometric detection (GC-FPD). A mixture of acetonitrile and n-hexane was used as an extraction solvent for the extraction of OPPs from tea samples. When the extraction process was finished, the mixture of solvents was rapidly dispersed in water; target analyte was extracted to a small volume of n-hexane, using DLLME. Recovery tests were performed for concentration 5.0 microg/kg. The recovery for each target analyte was in the range between 83.3 and 117.4%. The repeatability of the proposed method, expressed as relative standard deviation, varied between 3 and 7.8% (n=3). The detection limit of the method for tea was found ranging from 0.030 to 1 microg/kg for all the target pesticides. Compared with the conventional sample preparation method, the proposed method has the advantage of being quick and easy to operate, and has high-enrichment factors and low consumption of organic solvent.

Combination of dispersive liquid-liquid microextraction with flame atomic absorption spectrometry using microsample introduction for determination of lead in water samples.

The dispersive liquid-liquid microextraction (DLLME) was combined with the flame atomic absorption spectrometry (FAAS) for determination of lead in the water samples. Diethyldithiophosphoric acid (DDTP), carbon tetrachloride and methanol were used as chelating agent, extraction solvent and disperser solvent, respectively. A new FAAS sample introduction system was employed for the microvolume nebulization of the non-flammable chlorinated organic extracts. Injection of 20 microL volumes of the organic extract into an air-acetylene flame provided very sensitive spike-like and reproducible signals. Some effective parameters on the microextraction and the complex formation were selected and optimized. These parameters include extraction and disperser solvent type as well as their volume, extraction time, salt effect, pH and amount of the chelating agent. Under the optimized conditions, the enrichment factor of 450 was obtained from a sample volume of 25.0 mL. The enhancement factor, calculated as the ratio of the slopes of the calibration graphs with and without preconcentration, which was about 1000. The calibration graph was linear in the range of 1-70 microgL(-1) with a detection limit of 0.5 microgL(-1). The relative standard deviation (R.S.D.) for seven replicate measurements of 5.0 and 50 microgL(-1) of lead were 3.8 and 2.0%, respectively. The relative recoveries of lead in tap, well, river and seawater samples at the spiking level of 20 microgL(-1) ranged from 93.8 to 106.2%. The characteristics of the proposed method were compared with those of the liquid-liquid extraction (LLE), cloud point extraction (CPE), on-line and off-line solid-phase extraction (SPE) as well as co-precipitation, based on bibliographic data. Operation simplicity, rapidity, low cost, high enrichment factor, good repeatability, and low consumption of the extraction solvent at a microliter level are the main advantages of the proposed method.

Rapid determination of lead in water samples by dispersive liquid-liquid microextraction coupled with electrothermal atomic absorption spectrometry.

The need for highly reliable methods for the determination of trace and ultratrace elements has been recognized in analytical chemistry and environmental science. A simple and powerful microextraction technique was used for the detection of the lead ultratrace amounts in water samples using the dispersive liquid-liquid microextraction (DLLME), followed by the electrothermal atomic absorption spectrometry (ET AAS). In this microextraction technique, a mixture of 0.50 mL acetone (disperser solvent), containing 35 microL carbon tetrachloride (extraction solvent) and 5 microL diethyldithiophosphoric acid (chelating agent), was rapidly injected by syringe into the 5.00 mL water sample, spiked with lead. In this process, the lead ions reacted with the chelating agent and were extracted into the fine droplets of CCl(4). After centrifugation (2 min at 5000 rpm), the fine CCl4 droplets were sedimented at the bottom of the conical test tube (25+/-1 microL). Then, 20 microL from the sedimented phase, containing the enriched analyte, was determined by ET AAS. The next step was the optimization of various experimental conditions, affecting DLLME, such as the type and the volume of the extraction solvent, the type and the volume of the disperser solvent, the extraction time, the salt effect, pH and the chelating agent amount. Moreover, the effect of the interfering ions on the analytes recovery was also investigated. Under the optimum conditions, the enrichment factor of 150 was obtained from only a 5.00 mL water sample. The calibration graph was linear in the range of 0.05-1 microg L(-1) with the detection limit of 0.02 microg L(-1). The relative standard deviation (R.S.D.) for seven replicate measurements of 0.50 microg L(-1) of lead was 2.5%. The relative lead recoveries in mineral, tap, well and sea water samples at the spiking level of 0.20 and 0.40 microg L(-1) varied from 93.5 to 105.0. The characteristics of the proposed method were compared with the cloud point extraction (CPE), the liquid-liquid extraction, the solid phase extraction (SPE), the on-line solid phase extraction (SPE) and the co-precipitation, based on bibliographic data. The main DLLME advantages combined with ET AAS were simplicity of operation, rapidity, low cost, high-enrichment factor, good repeatability, low consumption of extraction solvent, requiring a low sample volume (5.00 mL).

Part-per-trillion determination of chlorobenzenes in water using dispersive liquid-liquid microextraction combined gas chromatography-electron capture detection.

In this study, a simple, rapid and efficient method, dispersive liquid-liquid microextraction (DLLME) combined gas chromatography-electron capture detection (GC-ECD), for the determination of chlorobenzenes (CBs) in water samples, has been described. This method involves the use of an appropriate mixture of extraction solvent (9.5 microl chlorobenzene) and disperser solvent (0.50 ml acetone) for the formation of cloudy solution in 5.00 ml aqueous sample containing analytes. After extraction, phase separation was performed by centrifugation and the enriched analytes in sedimented phase were determined by gas chromatography-electron capture detection (GC-ECD). Our simple conditions were conducted at room temperature with no stiring and no salt addition in order to minimize sample preparation steps. Parameters such as the kind and volume of extraction solvent, the kind and volume of disperser solvent, extraction time and salt effect, were studied and optimized. The method exhibited enrichment factors and recoveries ranging from 711 to 813 and 71.1 to 81.3%, respectively, within very short extraction time. The linearity of the method ranged from 0.05 to 100 microgl(-1) for dichlorobenzene isomers (DCB), 0.002-20 microgl(-1) for trichlorobenzene (TCB) and tetrachlorobenzene (TeCB) isomers and from 0.001 to 4 microgl(-1) for pentachlorobenzene (PeCB) and hexachlorobenzene (HCB). The limit of detection was in the low microgl(-1) level, ranging between 0.0005 and 0.05 microgl(-1). The relative standard deviations (R.S.D.s) for the concentration of DCB isomers, 5.00 microgl(-1), TCB and TeCB isomers, 0.500 microgl(-1), PeCB and HCB 0.100 microgl(-1) in water by using the internal standard were in the range of 0.52-2.8% (n=5) and without the internal standard were in the range of 4.6-6.0% (n=5). The relative recoveries of spiked CBs at different levels of chlorobenzene isomers in tap, well and river water samples were 109-121%, 105-113% and 87-120%, respectively. It is concluded that this method can be successfully applied for the determination of CBs in tap, river and well water samples.

Synthesis of salicylaldehyde-modified mesoporous silica and its application as a new sorbent for separation, preconcentration and determination of uranium by inductively coupled plasma atomic emission spectrometry.

A new functionalized mesoporous silica (MCM-41) using salicylaldehyde was utilized for the separation, preconcentration and determination of uranium in natural water by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions for effective adsorption of trace levels of U(VI) were optimized. The preconcentration factor was 100 (1.0 mL of elution for a 100 mL sample volume). The analytical curve was linear in the range 2-1000 microg L(-1) and the detection limit was 0.5 ng mL(-1). The relative standard deviation (R.S.D.) under optimum conditions was 2.5% (n=10). Common coexisting ions did not interfere with the separation and determination of uranium at pH 5. The sorbent exhibited excellent stability and its sorption capacity under optimum conditions has been found to be 10mg of uranium per gram of sorbent. The method was applied for the recovery and determination of uranium in different water samples.